마이크로컨트롤러

제품 (20,000+)

MKL02Z8VFG4 - 48MHz Cortex-M0+ MCU | NXP Semiconductors
MKL02Z8VFG4

MKL02Z8VFG4 - 48MHz Cortex-M0+ MCU | NXP Semiconductors

The NXP Semiconductors MKL02Z8VFG4 is an ultra-low-power 32-bit microcontroller built around the Arm Cortex-M0+ processor, operating at up to 48 MHz with 8 KB of flash memory and 1 KB of SRAM in a 16-QFN 3 x 3 mm package. It is designed for compact, cost-sensitive, battery-operated devices that need efficient control, low-power operation, and a small PCB footprint. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one device. The MKL02Z8VFG4 belongs to the Kinetis KL0x family, which provides an entry point into the Kinetis L series. Its Cortex-M0+ architecture supports compact embedded software while retaining familiar microcontroller peripherals, interrupt handling, and low-power operating modes for consumer, sensing, and industrial control products. The principal device characteristics include a 48 MHz maximum CPU frequency, 8 KB flash, 1 KB SRAM, a 16-QFN package, and a stated operating-temperature range of -40°C to +105°C. NXP identifies the part as active. The device also includes a 12-bit analog-to-digital converter, enabling compact products to measure analog signals without requiring a separate converter when the chosen analog front end and application requirements are compatible. The small 3 x 3 mm QFN package makes the MKL02Z8VFG4 appropriate for space-constrained products such as portable health devices, remote sensing nodes, compact consumer accessories, and low-power embedded controls. Its 8 KB flash footprint favors concise firmware, while 1 KB of SRAM supports the working memory required by lightweight control loops, configuration handling, and basic serial communication. The Cortex-M0+ platform and Kinetis L-series ecosystem also support migration from simpler 8-bit designs into a 32-bit software environment. Power-system design should begin with the exact operating modes, clock configuration, and peripheral states required by the end product. Because the MCU is intended for ultra-low-power systems, enable only the clocks and peripherals needed for each mode, and confirm wake timing against the required response time. Place the decoupling network close to the supply pins and preserve the exposed-pad connection recommended in the manufacturer package documentation to maintain electrical and thermal performance. This page combines the confirmed device identity, package, memory configuration, operating characteristics, application guidance, and packaging information with a conservative replacement analysis. Replacement candidates must be checked for exact pin mapping, boot behavior, peripheral availability, memory capacity, and software compatibility before being treated as production drop-ins. The Request a Quote form on this page can be used to request current availability, MOQ, lead time, and sourcing support for the exact MPN. The Kinetis KL02 family is also recognized by Arm Keil as supporting low-power devices, remote-sensing nodes, portable consumer products, and ingestible healthcare sensing. These use cases align with the MKL02Z8VFG4 combination of a Cortex-M0+ core, 8 KB flash, 1 KB SRAM, and a compact 16-QFN package. Firmware footprint, analog requirements, I/O count, temperature exposure, and package-level pin compatibility remain the decisive checks for each new design.

견적 요청 문의하기
MKL03Z32VFG4 - 48MHz 32KB Cortex-M0+ MCU | NXP | IoT
MKL03Z32VFG4

MKL03Z32VFG4 - 48MHz 32KB Cortex-M0+ MCU | NXP | IoT

The NXP Semiconductors MKL03Z32VFG4 is an ultra-low-power 32-bit Arm Cortex-M0+ microcontroller with a 48 MHz core, 32 KB flash memory, and 2 KB SRAM, packaged in a compact 16-QFN enclosure measuring 3 x 3 mm. It is designed for portable and space-constrained applications where low power consumption, compact size, and efficient processing must coexist in a single device. A microcontroller is a programmable integrated circuit containing a processor core, nonvolatile program memory, working memory, and peripherals. The MKL03Z32VFG4 belongs to the Kinetis KL03 family, an entry point into NXP's Kinetis L-series of Arm Cortex-M0+ devices. Its 48 MHz operating frequency supports responsive control and measurement tasks while maintaining low system power, making it suitable for battery-powered sensors, portable instruments, and connected edge devices. Key verified features include an Arm Cortex-M0+ processor core, 48 MHz maximum frequency, 32 KB flash, and 2 KB SRAM. The device also provides flexible clocking options and integrated power management, which help designers optimize energy use across active and low-power operating modes. Its small 16-QFN package supports dense PCB layouts while exposing the required connectivity and peripheral resources. The MKL03Z32VFG4 is positioned for portable applications requiring a compact, energy-efficient MCU rather than a high-performance processor. Its architecture is appropriate for simple control loops, sensor conditioning, low-rate communication, and embedded logic where deterministic peripheral interaction matters more than large memory capacity. The 32 KB flash footprint is well suited to compact firmware images and application-specific control code. Typical applications include wearable accessories, low-power sensor nodes, smart-home devices, battery-operated measurement equipment, portable medical accessories, and embedded control modules. Its small footprint is especially useful when PCB area is limited and low standby power is important. Designers should confirm the exact peripheral assignments, pin multiplexing, clock configuration, voltage limits, and memory map in the NXP manufacturer documentation before layout. The 3 x 3 mm QFN package also requires careful thermal-pad and solder-assembly planning. This page consolidates verified NXP and distributor information, pricing context, technical comparisons, and application guidance for engineers evaluating the MKL03Z32VFG4.

견적 요청 문의하기
MKL03Z32VFK4 - 48MHz Cortex-M0+ MCU, 32KB Flash | NXP
MKL03Z32VFK4

MKL03Z32VFK4 - 48MHz Cortex-M0+ MCU, 32KB Flash | NXP

The NXP Semiconductors MKL03Z32VFK4 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL03 sub-family, featuring 32KB of flash memory, 2KB of SRAM, and a maximum CPU frequency of 48 MHz, housed in a compact 24-pin QFN (4x4 mm) package. It is engineered for space-constrained, energy-efficient embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile memory (SRAM), non-volatile memory (flash), and a rich set of peripherals. The Cortex-M0+ is the smallest and most energy-efficient ARM core, designed for deterministic embedded control and ultra-low-power operation. The Kinetis KL03 belongs to NXP's KL0x family - the entry point into the Kinetis L series - and is software- and tool-compatible with all other Kinetis L series devices, easing migration from 8-bit architectures. In the broader hierarchy: Cortex-M0+ -> ARM Cortex-M -> 32-bit RISC core -> microcontroller -> semiconductor IC. Key specifications include 32KB program flash, 2KB SRAM, a 48 MHz maximum core frequency, an operating voltage range of 1.71V to 3.6V, and an ultra-low-power Run mode drawing well under 100 uA/MHz. The device integrates a 12-bit ADC, low-power UART, SPI, I2C, multiple timers, and a low-power comparator, alongside NXP's standard low-leakage wakeup unit. The 24-QFN (4x4 mm) package delivers a small PCB footprint suited to wearable and IoT form factors. The KL03 architecture uses an ARM Cortex-M0+ core with a single-cycle I/O bus and a low-latency interrupt controller, allowing deterministic response while drawing only microamps in deep sleep. On-chip voltage regulation and flexible low-power modes (VLLS, VLLS1, VLLS3, LLS, HSRUN, RUN, WAIT, STOP) make it ideal for battery-powered applications that must spend most of their life in sleep states. Typical applications include wearable fitness and health sensors, ultra-low-power wireless sensor nodes, IoT endpoints, smart home and building automation nodes, and battery-powered portable instrumentation. Designers choose the KL03 when they need the smallest possible Cortex-M0+ footprint with NXP's proven Kinetis peripheral set. When designing with this device, prioritize short, clean PCB traces between the decoupling capacitors and VDD/VSS pins to keep noise low and to support rapid wake transitions. Use the Kinetis SDK and MCUXpresso toolchain for code generation, and verify that your code uses only the on-chip peripherals to preserve the KL03's low-power advantage. This page synthesizes distributor pricing, drop-in Kinetis alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers shorten the device selection and PCB bring-up cycle for Kinetis KL0x designs.

견적 요청 문의하기
MKL03Z32VFK4R - 48MHz Cortex-M0+ MCU 32KB Flash | NXP
MKL03Z32VFK4R

MKL03Z32VFK4R - 48MHz Cortex-M0+ MCU 32KB Flash | NXP

The NXP Semiconductors MKL03Z32VFK4R is a 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL0x ultra-low-power MCU family, integrating 32 KB of flash memory and 2 KB of SRAM in a compact 24-pin QFN (4x4 mm) package. It runs at up to 48 MHz core frequency and supports 1.8 V, 2.5 V, and 3.3 V supply rails, making it the entry-level node of NXP's Kinetis L series. The part is qualified to AEC-Q100 standards for automotive applications and is offered on Tape & Reel packaging. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (flash), working memory (SRAM), and programmable peripherals. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor core, designed for always-on battery-powered devices. Within the taxonomy: microcontroller -> embedded system -> semiconductor -> integrated circuit. The KL0x family sits at the bottom of NXP's Kinetis L (Low-power) sub-tree, optimized for energy-harvesting and coin-cell designs. Key features include an ARM Cortex-M0+ core (Thumb/Thumb-2 instruction set, hardware single-cycle multiplier), low-power run, wait, stop, and VLLS modes, a 12-bit SAR ADC, a low-power timer, an analog comparator, and a flexible SPI/UART/I2C peripheral set. The 24-QFN package exposes up to 22 GPIO, supports single-cycle bit-banding in SRAM, and integrates a 32 kHz RTC oscillator. The device consumes approximately 1.5 mA active and sub-uA in deep-stop modes. The MKL03Z32VFK4R's ultra-low-power architecture, small 4x4 mm QFN footprint, and 48 MHz performance enable its use in space-constrained, energy-constrained designs. Typical applications include wearable fitness bands, IoT sensor nodes, energy-harvesting switches, automotive body controllers, and battery-powered metering peripherals. The Cortex-M0+ is binary-compatible upward with Cortex-M3/M4, so code can scale across NXP Kinetis families without architectural changes. When designing with this MCU, allocate decoupling capacitors (100 nF and 4.7 uF) adjacent to each power pin and follow NXP's QFN land-pattern guidelines to maximize thermal dissipation through the exposed pad. Programming is supported through NXP's Kinetis SDK and the LPCXpresso / MCUXpresso IDE toolchain. This page synthesizes distributor pricing, pin-compatible Kinetis KL0x variants, and practical PCB layout guidance not collected in any single manufacturer document.

견적 요청 문의하기
MKL03Z8VFK4 - 48MHz ARM Cortex-M0+ MCU 8KB Flash | NXP
MKL03Z8VFK4

MKL03Z8VFK4 - 48MHz ARM Cortex-M0+ MCU 8KB Flash | NXP

The NXP Semiconductors MKL03Z8VFK4 is an ARM Cortex-M0+ based Kinetis KL03 ultra-low-power 32-bit microcontroller running at 48 MHz, with 8 KB of Flash program memory and 2 KB of SRAM, offered in a 24-pin QFN (4x4 mm) package. A microcontroller (MCU) is an integrated circuit that combines a processor core, program memory, data memory, and a rich set of peripherals into a single chip used to embed control logic in electronic systems. The Cortex-M0+ core is the smallest and most energy-efficient member of the ARM Cortex-M family, designed for deterministic embedded control in cost- and power-sensitive products. Within NXP's portfolio, the KL0x family is the entry point of the Kinetis L series, providing a migration path for legacy 8-bit users into the ARM ecosystem while remaining software- and tool-compatible with all other Kinetis L series devices. Key features of the MKL03Z8VFK4 include a 48 MHz Cortex-M0+ core with single-cycle I/O access, 8 KB Flash and 2 KB SRAM, an ultra-low-power run mode down to 50 uA/MHz, multiple low-leakage stop modes, a low-power UART, 6-bit timer/PWM, and a tiny 1.6 x 2.0 mm WLCSP option (other variants). The 24-QFN (4x4) package provides a compact ~16 mm2 footprint ideal for space-constrained wearables and sensor nodes. The KL03 architecture uses the Cortex-M0+ core with a configurable NVIC, single-cycle 32x32 multiplier, and a 4-channel DMA controller. Its ultra-low-power design supports multiple stop modes with RAM retention, fast wake-up times, and an integrated low-power timer that keeps basic timing functions alive while the core is halted, making the part well suited to battery-powered always-on applications. Typical applications include wearable fitness bands, IoT sensor endpoints, low-power remote controls, smart metering nodes, and small consumer appliances. The combination of low active power, deep-sleep capability, and the tiny WLCSP/QFN footprint lets designers squeeze MCU functionality into coin-cell powered enclosures. When designing with the KL03, ensure the VDDC and VDD pins are properly decoupled with 100 nF ceramic capacitors placed within a few millimeters of the pins, and pay attention to the low-power UART and external crystal requirements for stop-mode wake-up timing. Source current ratings from the NXP Kinetis KL03 reference manual, not just the simplified datasheet, when budgeting battery life. This page synthesizes distributor pricing tiers, drop-in Kinetis KL0x family alternatives, and practical PCB-level design notes that are not assembled on any single manufacturer page, giving engineers a single decision-ready view of the MKL03Z8VFK4.

견적 요청 문의하기
MKL04Z16VLF4 - 48MHz Cortex-M0+ MCU 16KB Flash | NXP
MKL04Z16VLF4

MKL04Z16VLF4 - 48MHz Cortex-M0+ MCU 16KB Flash | NXP

The NXP Semiconductors MKL04Z16VLF4 is an ARM Cortex-M0+ based ultra-low-power microcontroller from the Kinetis KL0x family, featuring a 48 MHz core, 16 KB of Flash, and 2 KB of SRAM in a 48-pin LQFP (7x7 mm) package. It targets 8-bit customers migrating into the Kinetis L portfolio while remaining software and tool compatible with all other Kinetis L series devices, with 1.71-3.6V supply. What is a Kinetis KL0x microcontroller? The Kinetis KL0x family is NXP's entry-level ultra-low-power 32-bit MCU line based on the ARM Cortex-M0+ core. It sits at the base of the Kinetis L series hierarchy: Cortex-M0+ core -> ARM Cortex family -> 32-bit MCU -> microcontroller -> semiconductor. The family provides a bridge for 8-bit users transitioning to 32-bit performance while retaining low-power simplicity. Key features include 16 KB of embedded Flash, 2 KB of SRAM, a low-power ARM Cortex-M0+ core running at up to 48 MHz, multiple low-power modes (Wait, Stop, VLPR, VLPS, LLS, VLLS0/1/3), and an operating voltage range of 1.71V to 3.6V. The MKL04Z16VLF4 also integrates peripherals such as 12-bit ADC, analog comparator, low-power UART, low-power timer, and an SPI/I2C capable serial interface, providing ample connectivity for cost-sensitive designs. The device uses a Cortex-M0+ core with single-cycle I/O access and a Harvard bus architecture, achieving 0.95 DMIPS/MHz performance. On-chip peripherals operate directly from the ARM core through AMBA AHB-Lite, enabling deterministic real-time behavior. The KL04 sub-family is the smallest memory variant in the KL0x line, optimized for applications requiring minimal RAM and Flash. Typical applications include battery-powered sensor nodes, wearable fitness bands, electronic shelf labels, remote controls, low-end portable medical devices, and 8-bit replacement upgrades. The 1.71V minimum supply and sub-µA deep-sleep currents make it ideal for coin-cell powered products. When designing with this part, attention must be paid to the 48-LQAF pinout including analog reference pins (VREFH/VREFL) and the choice of reset configuration to ensure boot mode selection. A 0.1 µF decoupling capacitor close to each VDD/VSS pair is recommended, and unused analog inputs should be tied to a defined voltage to avoid ADC leakage. This page synthesizes distributor pricing, drop-in Kinetis alternatives, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
MKL04Z32VFK4 - 48MHz 32KB Cortex-M0+ MCU | NXP | 24-QFN
MKL04Z32VFK4

MKL04Z32VFK4 - 48MHz 32KB Cortex-M0+ MCU | NXP | 24-QFN

The NXP Semiconductors MKL04Z32VFK4 is a 48 MHz Arm Cortex-M0+ microcontroller with 32 KB of embedded Flash memory, 4 KB of SRAM, and a 24-QFN 4 x 4 mm package. Designed as an entry point into the Kinetis L series, it combines an ultra-low-power architecture with software and tool compatibility across the broader Kinetis L family. Its 32-bit processing core and compact package support cost-sensitive embedded products that need deterministic control without a large external memory system. What is an ultra-low-power Cortex-M0+ microcontroller? It is a 32-bit embedded-processing device built around the Arm Cortex-M0+ core, a compact instruction-set architecture intended for cost-sensitive control applications. Within the product hierarchy, this MCU is a microcontroller, embedded processor, and semiconductor. Compared with larger Cortex-M processors, the M0+ core emphasizes efficient code density, low energy use, and a small peripheral set rather than high-performance computing or extensive connectivity. Key verified features include a maximum operating frequency of 48 MHz, 32 KB Flash, 4 KB SRAM, and a 12-bit ADC. The device operates from a 1.71 V to 3.6 V supply and is specified across -40 degrees C to +105 degrees C. Its 24-QFN package measures 4 x 4 mm, making it suitable for compact industrial, consumer, sensor, and battery-powered equipment. The Kinetis L family positioning also provides a migration path from 8-bit designs without abandoning familiar tool workflows. The MKL04Z32VFK4 combines a small Cortex-M0+ core with analog measurement support and serial peripherals. Firmware can execute directly from internal Flash, reducing external component count and helping simplify compact PCB layouts. Its 4 KB SRAM supports control buffers, acquisition state, and communication stacks, although memory-heavy buffering may require careful partition design. The 12-bit ADC makes the device useful for direct sensor acquisition rather than relying entirely on external converters. Typical uses include low-cost condition-monitoring controllers, compact sensor nodes, industrial control modules, battery-powered instruments, and basic data-acquisition products. In these systems, the MCU can digitize analog inputs, apply control logic, and manage low-speed communications within a small board area. For designs needing higher performance, larger memory, USB, or advanced connectivity, a higher-tier Kinetis L or other Cortex-M MCU may be preferable. The primary design consideration is power architecture. Keep the 1.71 V to 3.6 V supply within its operating range, provide suitable decoupling at VDD pins, and reserve the exposed thermal pad according to the package land pattern. Route sensitive analog inputs away from switching nodes and high-current return paths to preserve signal quality. This page consolidates verified NXP and distributor information, package and application guidance, and engineering-oriented selection criteria that are not all present in a distributor catalog entry. It also distinguishes confirmed data from specifications that still require confirmation from the manufacturer datasheet.

견적 요청 문의하기
MKL04Z32VFM4 - 48MHz Cortex-M0+ 32KB Flash MCU | NXP
MKL04Z32VFM4

MKL04Z32VFM4 - 48MHz Cortex-M0+ 32KB Flash MCU | NXP

The NXP Semiconductors MKL04Z32VFM4 is a 32-bit Arm Cortex-M0+ microcontroller from the Kinetis KL04 (KL0x) family, running at up to 48 MHz with 32 KB flash and 4 KB SRAM in a 32-pin HVQFN (5x5 mm) package. A microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory, data memory, and peripherals such as timers, serial interfaces, and analog-to-digital converters. Within the MCU hierarchy, the Kinetis L series sits in the ultra-low-power 32-bit segment, and the KL0x family is its entry point, offering a bridge for 8-bit MCU users migrating to 32-bit Arm architecture while remaining software and tool compatible with all other Kinetis L devices. Key features of the MKL04Z32VFM4 include the efficient Cortex-M0+ core, which delivers ARM Cortex-class performance at very low power consumption, 32 KB of on-chip flash program memory for firmware storage, and 4 KB of SRAM for data. The 48 MHz maximum CPU clock supports real-time embedded control tasks, and the compact 5x5 mm QFN package suits space-constrained designs. The industrial temperature grade supports operation in harsh environments. Technically, the KL04 family uses NXP's low-power process technology and shares the Kinetis software ecosystem, including MCUXpresso SDK and tool compatibility across the Kinetis L portfolio. The Cortex-M0+ core's two-stage pipeline and reduced instruction complexity keep dynamic power low, making the device suitable for battery-powered and always-on applications. Typical applications include small consumer appliances, portable battery-powered devices, tactile and capacitive-sensing interfaces, simple motor control, and 8-bit MCU upgrades in industrial sensors. When designing with this MCU, verify supply voltage range, peripheral set, and pinout against the manufacturer datasheet before finalizing the PCB footprint, since the KL04 family is offered in multiple memory and package variants. This page synthesizes verified distributor data, drop-in same-family alternatives, pricing tiers, and practical design notes not found in a single manufacturer datasheet.

견적 요청 문의하기
MKL04Z32VLF4 - 48MHz Cortex-M0+ 32KB Flash MCU | NXP | LQFP-48
MKL04Z32VLF4

MKL04Z32VLF4 - 48MHz Cortex-M0+ 32KB Flash MCU | NXP | LQFP-48

NXP MKL04Z32VLF4 is a 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL04 sub-family, operating at up to 48 MHz with 32 KB of on-chip Flash and 4 KB of SRAM, housed in a 48-pin LQFP package (7x7 mm). It is the entry-level device of the Kinetis L series, designed for ultra-low-power applications and providing a bridge path for engineers migrating from 8-bit microcontrollers into the ARM Cortex-M ecosystem. What is a Kinetis L microcontroller? The Kinetis L family is NXP's ultra-low-power ARM Cortex-M0+ MCU portfolio, positioned below the Cortex-M4-based Kinetis K series. It targets battery-powered and energy-harvesting products where every microamp of quiescent current matters. Within the L series, the KL0x sub-family is the smallest and lowest-cost entry, while KL1x/2x/4x add richer peripherals and higher memory. Architecturally, an ARM Cortex-M0+ core sits on an advanced bus matrix with low-power peripherals and a flexible low-leakage wake-up unit, making the Kinetis L a power management IC companion in any embedded system. Key features include 32 KB program Flash, 4 KB SRAM, an 8-channel 12-bit SAR ADC, two analog comparators, a low-power hardware touch-sensing interface (TSI), up to 41 general-purpose I/O pins, and multiple serial peripherals including UART, SPI, and I2C. The device supports operating voltages from 1.71 V to 3.6 V and offers several low-power modes (Wait, Stop, VLPR, VLPS) that draw single-digit microamp currents, enabling years of battery life on coin-cell powered designs. The Cortex-M0+ core delivers 0.95 DMIPS/MHz with a two-stage pipeline and Thumb-2 instruction set compatibility. Typical applications include wearable fitness bands, remote controls, wireless sensor node endpoints, electronic shelf labels, smart-meter peripherals, low-end Bluetooth/BLE beacons, and consumer toys. The wide memory map and Kinetis peripheral compatibility also make the KL04 suitable as a co-processor or I/O expander in larger designs. Industrial and home appliance sub-modules (HMI buttons, motor control via PWM) are additional use cases. When designing with the MKL04Z32VLF4, ensure the decoupling network follows NXP's Kinetis L reference design: a 0.1 uF ceramic capacitor close to each VDD pin plus a bulk 4.7 uF capacitor. The LQFP-48 package has an exposed pad (pin 49/die pad) that must be soldered to the ground plane for thermal and electrical performance. The internal 1.2 V core regulator requires a 2.2 uF capacitor on VDCDC to operate correctly.

견적 요청 문의하기
MKL04Z8VFK4 - 48MHz Cortex-M0+ 8KB MCU | NXP
MKL04Z8VFK4

MKL04Z8VFK4 - 48MHz Cortex-M0+ 8KB MCU | NXP

The NXP Semiconductors MKL04Z8VFK4 is an ultra-low-power 32-bit Arm Cortex-M0+ microcontroller operating at 48 MHz, with 8 KB of flash memory, 1 KB of SRAM, and a 24-QFN 4 x 4 mm package. It belongs to the Kinetis KL0x family, where KL0x forms the entry point into the Kinetis L series for customers migrating from 8-bit systems. A microcontroller is a programmable semiconductor that integrates a processor core, program memory, data memory, and peripherals into one device. The MKL04Z8VFK4 uses the Arm Cortex-M0+ architecture, a compact 32-bit processor designed for cost-sensitive embedded control. Its role within an embedded system is to execute application code, read inputs, control outputs, and manage communications or timing functions without requiring a separate processor. The principal device parameters are a 48 MHz maximum clock frequency, 8 KB of flash memory, and 1 KB of SRAM. The operating supply identified for this 3.3 V device is 3.3 V. Its 24-QFN package uses a compact 4 x 4 mm land pattern, making it suitable for small embedded-control assemblies where board area is important. The exposed-pad package construction also provides a thermal and electrical land area on the PCB. The MKL04Z8VFK4 belongs to the Kinetis L series, and NXP describes the KL0x family as software and tool compatible with other Kinetis L series devices. This ecosystem relationship is important because an existing Kinetis L code base, development setup, or peripheral configuration workflow can reduce adoption effort. The device is identified as an ARM Cortex-M0+ Kinetis KL0 microcontroller with an active lifecycle status. Typical uses include compact sensor-control nodes, simple industrial controls, low-power monitoring modules, and cost-sensitive embedded products where a small package, modest memory footprint, and straightforward 32-bit control architecture are valuable. The 8 KB flash allocation is most appropriate for focused control firmware rather than graphics-heavy or connectivity-intensive workloads. Designers should use the NXP pin-description table when assigning PCB tracks because a complete 24-pin map is not included in the source material for this page. Confirm that flash, SRAM, clock, and peripheral requirements fit the application before finalizing firmware allocation. The 24-QFN land pattern also demands careful assembly planning because fine-pitch packages are sensitive to thermal profiles, pad alignment, and contamination. This page organizes the verified device identity, memory and package characteristics, replacement analysis, and practical selection guidance into one engineering-focused resource. It is intended to help embedded developers compare the MKL04Z8VFK4 with nearby NXP Kinetis options before committing the same PCB footprint, firmware environment, and supply plan to a production design.

견적 요청 문의하기
MKL04Z8VFM4 - 48MHz Cortex-M0+ 8KB Flash MCU, 32-HVQFN | NXP
MKL04Z8VFM4

MKL04Z8VFM4 - 48MHz Cortex-M0+ 8KB Flash MCU, 32-HVQFN | NXP

The NXP MKL04Z8VFM4 is an ultra-low-power 32-bit Arm Cortex-M0+ microcontroller operating up to 48 MHz, with 8 KB of embedded flash memory and 1 KB of SRAM, housed in a 32-pin HVQFN (5 x 5 mm) surface-mount package. A microcontroller (MCU) is a single integrated circuit that bundles a CPU core, program memory, data memory and peripheral blocks such as GPIO, timers and serial interfaces on one die. An MCU therefore sits at the bottom of the embedded hierarchy: microcontroller -> embedded processor -> semiconductor. The MKL04Z8VFM4 belongs to the NXP Kinetis KL0 series, the entry point of the Kinetis L family, and targets cost-sensitive, space-constrained designs where a full Cortex-M4 or Cortex-M7 is unnecessary. Key features of this device include a 48 MHz Arm Cortex-M0+ core with a 32-bit architecture, 8 KB (8K x 8) of on-chip flash for program storage, 1 KB of SRAM for data and stack, and a compact 32-pin HVQFN footprint measuring only 5 x 5 mm. NXP lists the device as Active, and the KL0 series is characterized by ultra-low-power operation for battery-driven equipment. The small package leaves board area for sensors, passives and antenna keep-out in wearables and compact sensor nodes. Technically, the Cortex-M0+ core extends the Armv6-M architecture with faster single-cycle GPIO handling, improved debug features and a hardware divide instruction, while keeping the code footprint small and the energy per operation low. The KL04 derivative combines this core with a low-power clocking scheme and a minimal peripheral set, which keeps both active current and standby current low without requiring an external crystal for many designs. Typical applications include Bluetooth and Zigbee radio modules, wireless sensor nodes, smart-home accessories, wearables, small USB-connected accessories, toys and simple control boards. Because the flash and SRAM budget is deliberately small, firmware must be compact and interrupt driven. The main design consideration is memory budget. With only 1 KB of SRAM, stack depth, buffer sizes and RTOS use must be planned carefully, and code should be kept under 8 KB of flash. Confirm the full pin list and electrical limits in the manufacturer datasheet before laying out the board. This page consolidates the core Kinetis KL04 specifications, drop-in alternatives from the same NXP family, a parameter-by-parameter comparison table and practical design notes that go beyond the basic datasheet summary.

견적 요청 문의하기
MKL05Z16VLC4 - 48MHz Cortex-M0+ MCU 16KB Flash LQFP-32 | NXP
MKL05Z16VLC4

MKL05Z16VLC4 - 48MHz Cortex-M0+ MCU 16KB Flash LQFP-32 | NXP

The NXP Semiconductors MKL05Z16VLC4 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller in the Kinetis KL0x sub-family, integrating 16 KB of Flash program memory and 2 KB of SRAM in a 32-pin LQFP (7x7 mm) package. It operates at a core frequency of 48 MHz from a wide 1.71 V to 3.6 V supply, making it suitable for both 1.8 V and 3.3 V system rails. The part is identified by the designator ‘VLC4’ in the part numbering scheme, indicating the 32-LQFP package and the -40C to +105C industrial temperature grade. An ARM Cortex-M0+ microcontroller is the entry-tier 32-bit core in the ARM Cortex-M family, designed for energy-efficient embedded applications. The Kinetis KL05 sub-family sits at the most resource-constrained node of the Kinetis L series, optimized for ultra-low-power operation and serving as a software- and tool-compatible migration path for legacy 8-bit MCU users. The Cortex-M0+ core implements the ARMv6-M instruction set with a 2-stage pipeline, delivering competitive DMIPS/mW while remaining compatible with the broader ARM Cortex-M ecosystem. Key features of the MKL05Z16VLC4 include a 48 MHz maximum CPU frequency, 16 KB Flash program memory, 2 KB SRAM, a low-power ARM Cortex-M0+ core, multiple low-power operating modes (Run, Wait, Stop, VLPR, VLPS, LLS, VLLSx), an integrated 12-bit ADC with DMA support, and a flexible low-power timer/LPTMR. A 32-channel DMA, CRC engine, and standard serial interfaces (UART, SPI, I2C) are integrated. The device includes an internal clock source, hardware touch-sensing interface (TSI), and a ROM bootloader for in-system programming. Architecturally, the MKL05Z16VLC4 leverages the Cortex-M0+ core tightly coupled with NXP’s low-power peripheral set and an integrated voltage regulator that supports multiple internal core voltage domains. This allows the device to enter deep-sleep states while retaining interrupt capability, with wake-up times in the single-digit microsecond range from VLLS modes. The 32-LQFP industrial package and 7x7 mm footprint provide an easy-to-route pinout for hand-soldered prototypes and high-volume SMT assembly. Typical applications include ultra-low-power sensor nodes, battery-powered IoT endpoints, wearable fitness bands, smart-metering sub-systems, industrial remote-control HMI, portable consumer electronics, and small home appliances. The wide operating voltage range and ultra-low-power Run/Stop modes make it ideal for coin-cell powered devices and Energy Harvesting designs where quiescent current dominates battery life. When designing with the MKL05Z16VLC4, observe the recommended decoupling scheme: a 100 nF X7R ceramic capacitor placed within 2 mm of each VDD/VSS pair, plus a bulk capacitor of 1 uF or larger on the main supply rail. Unused GPIO pins should be configured as outputs driven low (or inputs with the internal pull-up enabled) to minimize quiescent current in VLLS modes. This page synthesizes distributor inventory, parameter-by-parameter comparison against package-equivalent Kinetis KL0x variants, and practical design considerations that complement the manufacturer datasheet.

견적 요청 문의하기
MKL05Z32VFK4 - 48MHz Cortex-M0+ 32KB Flash MCU | NXP
MKL05Z32VFK4

MKL05Z32VFK4 - 48MHz Cortex-M0+ 32KB Flash MCU | NXP

The NXP Semiconductors MKL05Z32VFK4 is a 32-bit ARM Cortex-M0+ Kinetis KL0x microcontroller operating at up to 48 MHz, with 32KB Flash program memory, 4KB SRAM, and a 24-pin QFN (4x4 mm) package with exposed pad. A microcontroller (MCU) is a single-chip computer integrating a processor core, memory, and peripherals on one die. Within the MCU hierarchy, the Kinetis KL0x family is the entry point into NXP's Kinetis L series, which is built on the energy-efficient ARM Cortex-M0+ core - the most power-optimized member of the ARM Cortex-M profile, designed to replace 8-bit and 16-bit MCUs in cost- and power-sensitive embedded systems. Key features include 48 MHz core operation, 32KB of on-chip Flash, 4KB of SRAM, supply operation at 1.8V, 2.5V, or 3.3V, and an integrated peripheral set covering multiple timers, a real-time clock (RTC), an analog comparator, and a 4-channel DMA controller. The Cortex-M0+ pipeline with its two-stage design delivers low dynamic power consumption, and the small 4x4 mm QFN-EP footprint suits space-constrained designs. Technically, the KL0x family shares the Kinetis software and tool ecosystem - NXP MCUXpresso SDK and IDE, plus third-party tool support - which shortens time to market and allows migration upward to KL1x/KL2x devices when flash or peripheral requirements grow. The 24-QFN exposed-pad package also improves thermal performance and provides a low-inductance ground return. Typical applications include small consumer appliances, portable battery-powered devices, simple motor control and lighting systems, and sensor-interface nodes where 8-bit migration to 32-bit is desired. The RTC and low-power modes support always-on designs with limited energy budgets. A key design consideration is the modest 4KB SRAM: communication stacks or large buffering schemes must be planned carefully, and applications needing USB or larger RAM should step up to other Kinetis family members. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, with pricing referenced as of 2026-10-18.

견적 요청 문의하기
MKL05Z32VLF4 - 48MHz Cortex-M0+ MCU, 32KB Flash | NXP
MKL05Z32VLF4

MKL05Z32VLF4 - 48MHz Cortex-M0+ MCU, 32KB Flash | NXP

The NXP Semiconductors MKL05Z32VLF4 is a 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL0x family, delivering up to 48 MHz CPU performance with 32 KB of on-chip Flash and 4 KB of SRAM in a 48-pin LQFP (7x7 mm) package. It is designed as an entry-point MCU for the Kinetis L ultra-low-power series, targeting 8-bit customers migrating to the ARM ecosystem while remaining software- and tool-compatible with other Kinetis L devices. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals on one die. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor core, intended for deterministic embedded workloads. Kinetis L MCUs form a sub-family of NXP's Kinetis portfolio optimized for ultra-low-power (ULP) operation, making them well suited for battery-powered products where every microamp of quiescent current matters. Key features include 32 KB Flash, 4 KB SRAM, an ultra-low-power ARM Cortex-M0+ core running at up to 48 MHz, an operating voltage range of 1.8 V to 3.6 V, a low-power real-time clock (RTC), and multiple serial interfaces including UART, SPI, and I2C. The 48-LQFP package is industry standard and easy to hand-solder or reflow, with a thermal resistance suitable for consumer and industrial ambient temperatures from -40 C to +105 C. Architecturally, the KL0x family combines a Cortex-M0+ core with NXP's low-power peripheral set, segmented run/sleep/wait modes, and a flexible clock tree. The result is a deterministic MCU with predictable interrupt latency and very low run current (~4 mA typical), enabling coin-cell and energy-harvesting designs where larger Cortex-M3/M4 parts would be excessive. Typical applications include low-power wearables, IoT sensor nodes, battery-powered HVAC controllers, simple motor control, and 8-bit-to-32-bit migration projects where engineers want ARM Cortex-M0+ performance without stepping up to higher-cost Cortex-M3/M4 devices. The compact 48-LQFP footprint also simplifies retrofits of legacy 8-bit designs. When designing with this MCU, remember that the 48-LQFP package has a moderate thermal resistance; for sustained high-MIPS workloads, derate ambient temperature or move to the larger 64-LQFP Kinetis L siblings. The internal 1 kHz low-power oscillator and flexible clocking must be configured correctly to honor the ultra-low-power marketing claim - default out-of-reset clock settings can idle the CPU at higher current than expected. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers rapidly evaluate the MKL05Z32VLF4 for new designs and field replacements.

견적 요청 문의하기
MKL05Z8VFM4 - 48MHz Cortex-M0+ 32-QFN MCU | NXP
MKL05Z8VFM4

MKL05Z8VFM4 - 48MHz Cortex-M0+ 32-QFN MCU | NXP

NXP Semiconductors MKL05Z8VFM4 is an ultra-low-power 32-bit Kinetis KL0 microcontroller built around an Arm Cortex-M0+ processor operating at 48 MHz. The device provides 8 KB of flash memory and 1 KB of SRAM in a 32-pin HVQFN package measuring 5 mm by 5 mm. Its combination of compact packaging, embedded memory, and low-power-oriented design makes it suitable for space-constrained embedded control systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripheral interfaces into one device. The Kinetis KL0 family belongs to the broader Kinetis L series of Arm Cortex-M0+ microcontrollers and provides an entry point for designers migrating from 8-bit embedded architectures. NXP describes the KL0 family as software- and tool-compatible with other Kinetis L series devices, supporting a connected development and migration path. The MKL05Z8VFM4 core operates at 48 MHz and includes 8 KB of flash for firmware and 1 KB of SRAM for working data. Its 32-bit Arm Cortex-M0+ architecture provides a larger addressable data space than a conventional 8-bit controller while retaining a simple peripheral and software model. The 5 mm by 5 mm HVQFN package supports compact PCB layouts while exposing a larger set of connections than a basic dual in-line package. Ultra-low-power operation is the principal technical emphasis of the Kinetis KL0 family. NXP positions these devices as a bridge from 8-bit designs into the Kinetis portfolio, where power-conscious embedded systems can use a 32-bit architecture without adopting a larger general-purpose microcontroller. Sleep behavior, clock configuration, run-mode current, and peripheral shutdown options should be evaluated against the actual sensing, communications, and control workload before finalizing the power budget. Typical uses include compact sensor nodes, building-access controls, small industrial controllers, battery-operated accessories, and connected products that require deterministic control in a constrained footprint. The 8 KB flash capacity is suitable for compact applications that do not require a large graphical interface, extensive protocol stack, or long application code. Firmware size, stack requirements, bootloader support, and middleware memory use should be measured during software bring-up. PCB design should follow the manufacturer land pattern for the 32-pin HVQFN, including the exposed thermal pad, pad dimensions, solder-mask definition, and paste stencil. Maintain a low-resistance ground plane, keep sensitive timing and programming interfaces away from noisy switching nodes, and validate the power network for transient response. The exposed pad must be thermally connected through solder and copper according to the package land pattern. This product page combines the manufacturer's core device identification with package, memory, application, and sourcing guidance. It also distinguishes confirmed drop-in replacements from related Kinetis options, helping engineers determine whether a board can be reused without changing the footprint, firmware assumptions, memory budget, or peripheral configuration.

견적 요청 문의하기
MKL05Z8VLC4 - 48MHz Cortex-M0+ 8KB MCU | NXP
MKL05Z8VLC4

MKL05Z8VLC4 - 48MHz Cortex-M0+ 8KB MCU | NXP

The NXP Semiconductors MKL05Z8VLC4 is a 48 MHz ARM Cortex-M0+ microcontroller with 8 KB of Flash memory, 1 KB of SRAM, and a 32-LQFP 7 x 7 mm package. It operates from 1.8 V, 2.5 V, or 3.3 V supply levels and combines an ultra-low-power design with serial interfaces and analog peripherals for compact embedded systems. An ultra-low-power microcontroller is a semiconductor designed to minimize energy consumption while executing control, measurement, and communication tasks. The Kinetis KL05 family belongs to the ARM Cortex-M0+ class of 32-bit embedded processors and provides a practical entry point for cost-sensitive, low-power systems. Its small memory footprint suits simple control nodes, while the selectable operating voltages support both 3.3 V industrial electronics and lower-voltage portable equipment. The MKL05Z8VLC4 provides a 48 MHz ARM Cortex-M0+ core, 8 KB of Flash program memory, and 1 KB of SRAM. Multiple serial interfaces allow connections to sensors, transceivers, memory devices, and external controllers. Analog peripherals support embedded measurement and control, while the 32-LQFP package provides a conventional surface-mount form factor with visible leads for inspection and rework. The device is positioned as the entry point to the Kinetis L series, combining an ARM Cortex-M0+ instruction set with low-power operation and integrated peripherals. Its 8 KB Flash capacity is intended for compact firmware rather than graphical interfaces or large protocol stacks. The 1 KB SRAM supports working variables, stack storage, and short communication buffers, so application architecture should avoid unnecessary RAM copies and large frame buffers. Typical uses include low-power sensor nodes, small industrial controllers, battery-powered accessories, compact data loggers, and embedded communication modules. The selectable 1.8 V, 2.5 V, and 3.3 V operating levels simplify connection to mixed-signal and portable systems. Its serial interfaces can also bridge external sensors or communication modules while the analog peripherals handle local thresholding, filtering, or control functions. When designing a board around the MKL05Z8VLC4, verify the complete pin assignment and peripheral multiplexing in the manufacturer datasheet before routing PCB traces. Place decoupling capacitors close to the supply pins, keep sensitive analog routes compact, and use the package ground and power pins for low-noise return paths. Software should also respect the limited 8 KB Flash and 1 KB SRAM budgets. This product page combines the exact orderable MPN, package details, operating specifications, same-family alternatives, application guidance, and engineering-focused design notes to support component selection and PCB planning.

견적 요청 문의하기
MKL14Z64VLH4 - 48MHz Cortex-M0+ MCU, 64KB Flash | NXP
MKL14Z64VLH4

MKL14Z64VLH4 - 48MHz Cortex-M0+ MCU, 64KB Flash | NXP

The NXP MKL14Z64VLH4 is a 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL1x sub-family, running up to 48 MHz with 64 KB of on-chip Flash and 8 KB SRAM, packaged in a 64-pin LQFP (10x10 mm). It is engineered for ultra-low-power embedded applications and integrates rich connectivity including I2C, LINbus, SPI, and UART/USART, alongside on-chip peripherals such as Brown-out Detect/Reset, DMA, LVD, POR, PWM, and a Watchdog Timer. Background Knowledge: A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and peripheral interfaces. The Cortex-M0+ is ARM's smallest and most energy-efficient 32-bit core, designed as a successor to 8-bit/16-bit MCUs while retaining ultra-low power consumption. Within NXP's portfolio, the Kinetis KL1x family sits above the KL0x entry-level and below the K2x/KL4x higher-integration families, providing a migration path to the Cortex-M4-based K10 family. Key features include a wide operating voltage range (1.71 V to 3.6 V, with the part typically offered at 1.8 V/2.5 V/3.3 V rails), multiple low-power modes, an internal clock source, and 12-bit ADC plus comparators and touch sensing interfaces on selected variants. The 48 MHz core delivers 0.93 DMIPS/MHz, sufficient for sensor fusion, Human-Machine Interface (HMI), and portable instrumentation consumer designs. Typical applications span ultra-low-power battery-powered IoT end nodes, wearable health and fitness devices, smart home sensor hubs, industrial sensing nodes, automotive body and LIN-bus sub-modules, and consumer HMI panels using segmented LCD or touch interfaces. The combination of low active current and deep-sleep current below 1 microamp enables years of operation from a single coin cell. Design considerations: engineers should evaluate deep-sleep current versus wake-up latency when designing battery-powered nodes. Pin-muxing is extensive on the LQFP-64 footprint; locking the peripheral assignment in the Kinetis configuration tool early avoids late-stage rework. This page synthesizes distributor pricing, drop-in Kinetis alternatives, and practical design notes not consolidated in the manufacturer datasheet alone.

견적 요청 문의하기
MKL15Z128VLH4 - 48MHz Cortex-M0+ 128KB Flash MCU | NXP | Kinetis
MKL15Z128VLH4

MKL15Z128VLH4 - 48MHz Cortex-M0+ 128KB Flash MCU | NXP | Kinetis

The NXP Semiconductors MKL15Z128VLH4 is a 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL1x ultra-low-power family, operating at up to 48 MHz with 128 KB of Flash and 16 KB of SRAM in a 64-pin LQFP (10x10 mm) package. It supports a wide operating voltage range from 1.71 V to 3.6 V and is qualified to AEC-Q100 for automotive applications, with an ambient operating temperature range of -40 °C to +105 °C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor core, optimized for deterministic interrupt response and ultra-low active power. MCUs sit within the hierarchy of embedded computing devices, beneath microprocessors and above simple digital signal controllers; the Kinetis L family specifically targets battery-powered and energy-harvesting designs where milliamp budgets dominate BOM decisions. Key features include an integrated 12-bit SAR ADC with up to 16 channels, a 16-bit ADC option, multiple low-power modes (Wait, Very-Low-Power Wait, Stop, VLLS0/1/3), and NXP's low-power touch sensor interface (TSI). Communications peripherals include I²C, UART, SPI, I²S, and USB 2.0 full-speed OTG with on-chip transceiver. The KL15 sub-family extends the KL0x with additional SRAM, communications options, and analog integration while retaining the same Cortex-M0+ instruction set. Architecturally the MKL15Z128VLH4 uses a 2-bit dual-core implementation with a single-cycle 32x32 hardware multiplier, a 4-channel DMA controller, and a low-leakage wake-up unit. The Flash is organized as 128K x 8 with ECC-style reliability, and the SRAM is 16 KB with parity. The part operates from internal or external references and supports a 4-bit GPIO port configuration across 53 usable I/O pins on the 64-LQFP. Typical applications include portable medical devices, wearable fitness trackers, home automation sensor hubs, automotive body controllers, smart-metering endpoints, USB-capable accessories (HID, game controllers, data loggers), and low-power industrial sensor nodes. The wide voltage range and on-chip USB OTG transceiver make it a common drop-in for legacy Freescale (now NXP) designs migrating to the Cortex-M0+ ecosystem. When designing with the MKL15Z128VLH4, ensure that the supply decoupling follows the KL15 reference manual (one 100 nF per VDD pin, one bulk 4.7 µF) and that the USB VBUS pin sees a regulated 5 V-tolerant rail per the USB OTG specification. For best low-power performance, enter VLLS0 with the low-leakage wake-up unit enabled and avoid leaving floating digital inputs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
MKL15Z128VLH4R - ARM Cortex-M0+ 48MHz MCU, 128KB Flash | NXP
MKL15Z128VLH4R

MKL15Z128VLH4R - ARM Cortex-M0+ 48MHz MCU, 128KB Flash | NXP

The NXP Semiconductors MKL15Z128VLH4R is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller operating at 48 MHz with 128 KB of flash and 16 KB of SRAM, housed in a 64-pin LQFP (10x10 mm) package with tape-and-reel packaging. As a member of the Kinetis KL1x family, the part integrates USB 2.0 OTG full-speed, flexible low-power modes, a 12-bit SAR ADC, and a rich set of serial peripherals. The 'R' suffix indicates tape-and-reel delivery, while the base MKL15Z128VLH4 ships in tray. The 64-LQFP package is the standard footprint across the KL14/KL15/KL16/KL17 families, enabling PCB reuse when scaling designs. An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core designed by Arm for energy-constrained embedded applications, featuring a 2-stage pipeline, single-cycle 32x32 multiplier, and Thumb-2 instruction set. It belongs to the broader hierarchy of ARM Cortex-M processors (Cortex-M0/M0+/M3/M4/M7), with the M0+ positioned as the most power-efficient tier while retaining full instruction compatibility with larger cores. Kinetis L series microcontrollers specifically target battery-powered and portable devices through aggressive use of multiple low-power modes (Run, Wait, Stop, VLPR, VLPW, VLPS, LLWU). Key features of the MKL15Z128VLH4R include 128 KB program flash, 16 KB SRAM, USB 2.0 full-speed OTG with on-chip transceiver, an 8-channel 12-bit ADC, two 16-bit timers, a low-power timer, RTC, CMP, and multiple serial communication modules (UART, SPI, I2C). The device supports 1.71V to 3.6V supply and provides 54 GPIO pins plus dedicated USB DP/DM. Hardware cryptography, tamper detection, and secure firmware update are not present on this KL15 sub-family, distinguishing it from the higher-end Kinetis K-series. From an architectural perspective, the M0+ core delivers 0.93 DMIPS/MHz while drawing only 9 uA/MHz in Run mode at 3V, and as low as 2.1 uA in VLPS mode with RTC retention. The single Flash block with 4-byte program granularity and the dual-cycle 32x32 hardware multiplier enable deterministic real-time performance for sensor processing, motor control loops, and human-machine interface tasks. Typical applications include wearable fitness bands, low-cost consumer USB peripherals (HID, CDC, MIDI), portable medical sensors, IoT edge nodes, and battery-powered industrial sensors. The integrated USB 2.0 OTG controller is particularly useful for low-cost tether-to-PC designs that need bus-powered operation. When designing with this part, prioritize supply decoupling (0.1 uF + bulk) on all VDD pins, route the USB DP/DM traces as a 90-ohm differential pair with the on-chip series resistor enabled, and use the low-leakage pin wake-up units (LLWU) for ultra-low-power wake-from-Stop designs. This page synthesizes distributor pricing, parametric comparison, and drop-in alternatives across the Kinetis L family and competing Cortex-M0+ MCUs - information not aggregated in any single manufacturer datasheet.

견적 요청 문의하기
MKL15Z32VFT4 - 48MHz Cortex-M0+ 32KB Flash MCU | NXP
MKL15Z32VFT4

MKL15Z32VFT4 - 48MHz Cortex-M0+ 32KB Flash MCU | NXP

The NXP MKL15Z32VFT4 is an ARM Cortex-M0+ based ultra-low-power microcontroller from the Kinetis KL1x family, featuring 32KB flash, 4KB SRAM, and a 48 MHz core clock, housed in a 48-pin QFN (7x7 mm) package with exposed pad. What is a Kinetis KL1x microcontroller? The Kinetis KL1x is NXP's general-purpose ultra-low-power MCU family that builds on the KL0x family by adding more memory, communication peripherals, and analog options. The MKL15Z32VFT4 sits in this hierarchy as: microcontroller -> 32-bit MCU -> ARM Cortex-M0+ MCU -> Kinetis family -> KL1x sub-family -> KL15 sub-sub-family. The Cortex-M0+ core itself is the smallest, most energy-efficient ARM core, designed for cost-sensitive embedded applications where deterministic low power matters more than raw performance. Key features include an operating voltage range of 1.71V to 3.6V, an industrial temperature range of -40C to +105C, a 12-bit ADC, multiple serial interfaces, low-power operating modes with sub-uA sleep currents, and an integrated 32KB flash memory array. The device also integrates a 16-bit SAR ADC, comparators, and a flexible low-power timer, making it suitable for battery-powered sensor products. Architecturally, the MKL15Z32VFT4 leverages the Cortex-M0+ core's two-stage pipeline and single-cycle I/O access, paired with NXP's low-leakage process technology and an integrated voltage regulator. The 48 MHz core clock delivers 0.93 DMIPS/MHz and supports both Thumb and Thumb-2 instruction subsets. The chip integrates up to 40 GPIO, multiple DMA channels, and a peripheral crossbar for flexible signal routing. Typical applications include wearable health monitors, battery-powered IoT sensor nodes, low-end consumer electronics, and industrial control nodes where energy harvesting or coin-cell operation is desired. The exposed thermal pad on the QFN package improves dissipation for sustained 48 MHz operation. When designing with this part, pay attention to the exposed pad (EP) connection to the ground plane for thermal and electrical performance. Use NXP's Kinetis Design Studio or MCUXpresso toolchain for firmware development, and ensure the brown-out and low-voltage detect settings match the battery chemistry profile. This page synthesizes distributor pricing, drop-in alternatives from the same Kinetis family, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
MKL15Z64VFT4 - 48MHz Cortex-M0+ MCU, 64KB Flash | NXP
MKL15Z64VFT4

MKL15Z64VFT4 - 48MHz Cortex-M0+ MCU, 64KB Flash | NXP

The NXP Semiconductors MKL15Z64VFT4 is an ARM Cortex-M0+ based ultra-low-power microcontroller from the Kinetis KL1x sub-family, offering 48 MHz CPU performance with 64 KB of embedded Flash and 8 KB of SRAM in a 48-pin QFN (7x7 mm) package. According to NXP product information, this MCU integrates connectivity peripherals including I2C, LINbus, SPI, UART/USART, and a Touch Sensing Interface (TSI), along with on-chip analog and timing peripherals for embedded designs. What is a Kinetis KL1x microcontroller? The Kinetis KL1x family is a general-purpose ultra-low-power 32-bit MCU line from NXP based on the ARM Cortex-M0+ core, succeeding the original Kinetis KL0x family with additional memory, communications, and analog peripheral options. Within the hierarchy, KL1x sits beneath Kinetis K-series Cortex-M4 parts (K10/K20/K40/K60) and above KL0x in NXP's ultra-low-power portfolio, providing a migration path to higher performance while preserving the same peripheral IP and toolchain. Key technical features include Brown-out Detect/Reset, Low-Voltage Detect (LVD), Power-On Reset (POR), Direct Memory Access (DMA), a Watchdog Timer (WDT), and PWM channels suitable for motor control or LED driving. The device runs from a single 3.3 V supply and supports a wide operating temperature range suitable for industrial applications. The integrated TSI block enables capacitive touch user interfaces without external touch controllers. Architecture-wise, the KL1x uses the efficient ARM Cortex-M0+ core with single-cycle I/O access, Thumb-2 instruction set, and a deterministic interrupt controller. The 64 KB Flash program memory is split into a primary block plus a separate FlexMemory or EEPROM emulation region depending on configuration, while the 8 KB SRAM provides ample space for protocol stacks and application state. Typical applications include ultra-low-power industrial sensor nodes, capacitive touch user interfaces, home appliances with LIN-bus connectivity, low-end consumer electronics, and battery-powered IoT edge devices. The combination of low-power modes, multiple serial interfaces, and TSI makes the KL1x well-suited to mains-powered and battery-powered products alike. When designing with this part, ensure the PCB footprint matches the 48-QFN (7x7) land pattern with proper thermal via arrangement under the exposed pad. The NXP Kinetis SDK and Processor Expert tooling provide firmware drivers; pin multiplexing must be configured via the PORT and SIM modules before peripheral activation. Selected power modes such as VLLS0/VLLS1 should be evaluated carefully against wakeup source requirements. This page consolidates distributor pricing, package-equivalent KL1x alternatives, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
MKL16Z128VLH4 - 48MHz Cortex-M0+ MCU 128KB Flash LQFP-64 | NXP
MKL16Z128VLH4

MKL16Z128VLH4 - 48MHz Cortex-M0+ MCU 128KB Flash LQFP-64 | NXP

The NXP Semiconductors MKL16Z128VLH4 is a Kinetis KL16 ultra-low-power microcontroller featuring an ARM Cortex-M0+ core running at up to 48 MHz, with 128 KB of on-chip Flash and 16 KB of SRAM, housed in a 64-pin LQFP (10x10 mm) package. It integrates a full-speed USB 2.0 device controller, 12-bit ADC, low-power timer (LPTMR), real-time clock (RTC), and multiple serial interfaces including UART, SPI, and I²C. An MCU (microcontroller unit) is a single-chip computer that integrates a processor core, memory, and programmable peripherals, sitting at the top of the embedded computing hierarchy: microcontroller -> microprocessor -> semiconductor. The Kinetis KL1x sub-family extends the KL0x with additional memory and connectivity, and the KL16 variant adds USB while maintaining the ultra-low-power modes that make Kinetis parts popular for battery-powered designs. Key features include 48 MHz maximum CPU frequency, 128 KB program Flash, 16 KB SRAM, USB 2.0 Full-Speed device with on-chip transceiver, 12-bit SAR ADC with up to 16 channels, multiple low-power modes (Wait, Stop, VLPR, VLPS), and a low-power timer that can run in all power modes. The 64-LQFP footprint (10x10 mm) provides ample GPIO for typical embedded applications. The KL16 architecture pairs an ARM Cortex-M0+ core (single-cycle 32-bit multiply, Harvard bus, NVIC with 32 interrupts) with NXP's ultra-low-power design techniques, including multiple clock gating domains and fast wake-up from low-power states. On-chip peripherals are mapped through an AIPS-Lite bus structure that simplifies DMA and interrupt routing for deterministic real-time behavior. Typical applications include wearable health and fitness devices, USB peripherals (HID, CDC, custom classes), home automation sensors, smart metering endpoints, and portable consumer electronics. The integrated USB 2.0 FS device eliminates the need for an external transceiver, reducing BOM cost in USB HID, CDC, or vendor-class device designs. When designing with this part, choose the correct Flash size variant in the family (KL16: 64KB/128KB/256KB) to match your code footprint. Take advantage of the multiple low-power modes for battery operation, but verify that any peripheral used in VLPS/VLPR is in the chip-specific low-power compatibility list. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers and procurement teams evaluate the MKL16Z128VLH4 for new designs and second-source decisions.

견적 요청 문의하기
MKL16Z256VLH4 - 48MHz Cortex-M0+ 256KB Flash MCU | NXP
MKL16Z256VLH4

MKL16Z256VLH4 - 48MHz Cortex-M0+ 256KB Flash MCU | NXP

The NXP Semiconductors MKL16Z256VLH4 is a 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL1 family, running at up to 48 MHz with 256KB (256K x 8) on-chip flash memory, housed in a 64-pin LQFP (10x10 mm) surface-mount package. A microcontroller (MCU) is a single-chip embedded computer that integrates a processor core, program memory, data memory, and peripherals on one die, serving as the compute element at the heart of embedded systems within the broader power-and-control hierarchy of modern electronics. The Kinetis KL series belongs to the class of ultra-low-power 32-bit MCUs built on the energy-efficient ARM Cortex-M0+ architecture. Key features of the MKL16Z256VLH4 include the FlexUSB module for USB device connectivity, an integrated segment LCD controller for direct glass drive, and the exceptional energy efficiency that defines the Kinetis L family, combining the ease of use of the Cortex-M0+ core with rich peripheral integration. Architecturally, the device pairs the two-stage Cortex-M0+ pipeline with NXP Kinetis peripheral sets, enabling scalable designs that can migrate across the Kinetis 32-bit portfolio while preserving software enablement. The 256KB flash provides ample room for protocol stacks such as USB HID/CDC classes and UI code driving the segment LCD. Typical applications include battery-powered human-machine interfaces with LCD displays, USB-connected sensor endpoints, consumer appliance panels, and industrial low-power monitoring nodes where energy efficiency and display capability matter. For design, plan USB and LCD pin assignments early, since the FlexUSB and segment LCD controller share the finite I/O pool of the 64-LQFP package. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
MKL16Z32VFT4 - 48MHz Cortex-M0+ MCU 32KB Flash | NXP
MKL16Z32VFT4

MKL16Z32VFT4 - 48MHz Cortex-M0+ MCU 32KB Flash | NXP

The NXP Semiconductors MKL16Z32VFT4 is a Kinetis KL16 series 32-bit microcontroller built on an Arm Cortex-M0+ core running at up to 48 MHz, integrating 32 KB of flash memory and 4 KB of SRAM in a 48-pin QFN (7x7 mm) package with exposed pad. It operates from a 1.8V, 2.5V, or 3.3V supply per distributor listings from Arrow and DigiKey. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals into one chip, forming the lowest layer of the embedded-system hierarchy: MCU family (Kinetis KL1x) -> general-purpose MCU -> embedded processor -> semiconductor device. The KL1x family extends the ultra-low-power KL0x family with additional memory, communication, and analog peripheral options. Key features include the Cortex-M0+ core, the most energy-efficient Arm processor profile, delivering 48 MHz performance at very low dynamic current; 32 KB on-chip flash for program storage and 4 KB SRAM for data; and a rich peripheral set typical of the KL16 sub-family, including serial communication interfaces (UART, SPI, I2C), a 12-bit ADC, timers, and GPIO, plus low-power modes suited to battery-operated products. Technically, the Kinetis KL16 sub-family shares the same platform architecture as other Kinetis MCUs, with a crossbar bus, peripheral clock gating, and bitband-style GPIO control. The exposed-pad QFN package improves thermal and electrical performance versus a standard QFN, and the 7x7 mm footprint with 0.5 mm pitch suits compact two- and four-layer PCBs. Typical applications include portable and battery-powered consumer devices, sensor nodes and IoT end points, human-interface and touch sensing products, and small industrial control boards where ultra-low power and a small footprint matter more than raw processing throughput. A key design consideration is memory headroom: at 32 KB flash and 4 KB SRAM, code size and stack usage should be budgeted early, and the pin-compatible larger-memory siblings in the same package can be used as upgrade paths. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기