MKL03Z32VFK4 - 48MHz Cortex-M0+ MCU, 32KB Flash | NXP
부품 번호: MKL03Z32VFK4 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $2.95 | $2.95 |
| 10 | $2.66 | $26.60 |
| 100 | $2.37 | $237.00 |
| 500 | $2.13 | $1,065.00 |
| 1,000 | $1.9 | $1,900.00 |
| 3,000 | $1.61 | $4,830.00 |
MKL03Z32VFK4 개요
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile memory (SRAM), non-volatile memory (flash), and a rich set of peripherals. The Cortex-M0+ is the smallest and most energy-efficient ARM core, designed for deterministic embedded control and ultra-low-power operation. The Kinetis KL03 belongs to NXP's KL0x family - the entry point into the Kinetis L series - and is software- and tool-compatible with all other Kinetis L series devices, easing migration from 8-bit architectures. In the broader hierarchy: Cortex-M0+ -> ARM Cortex-M -> 32-bit RISC core -> microcontroller -> semiconductor IC.
Key specifications include 32KB program flash, 2KB SRAM, a 48 MHz maximum core frequency, an operating voltage range of 1.71V to 3.6V, and an ultra-low-power Run mode drawing well under 100 uA/MHz. The device integrates a 12-bit ADC, low-power UART, SPI, I2C, multiple timers, and a low-power comparator, alongside NXP's standard low-leakage wakeup unit. The 24-QFN (4x4 mm) package delivers a small PCB footprint suited to wearable and IoT form factors.
The KL03 architecture uses an ARM Cortex-M0+ core with a single-cycle I/O bus and a low-latency interrupt controller, allowing deterministic response while drawing only microamps in deep sleep. On-chip voltage regulation and flexible low-power modes (VLLS, VLLS1, VLLS3, LLS, HSRUN, RUN, WAIT, STOP) make it ideal for battery-powered applications that must spend most of their life in sleep states.
Typical applications include wearable fitness and health sensors, ultra-low-power wireless sensor nodes, IoT endpoints, smart home and building automation nodes, and battery-powered portable instrumentation. Designers choose the KL03 when they need the smallest possible Cortex-M0+ footprint with NXP's proven Kinetis peripheral set.
When designing with this device, prioritize short, clean PCB traces between the decoupling capacitors and VDD/VSS pins to keep noise low and to support rapid wake transitions. Use the Kinetis SDK and MCUXpresso toolchain for code generation, and verify that your code uses only the on-chip peripherals to preserve the KL03's low-power advantage.
This page synthesizes distributor pricing, drop-in Kinetis alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers shorten the device selection and PCB bring-up cycle for Kinetis KL0x designs.
드롭인 대체품: MKL03Z32VFK4 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MKL03Z32VFK4 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Operating Temperature Range, SRAM, Communication Interfaces, Flash Memory.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MKL03Z32VFG4
✅ 드롭인✓ 재고 있음
$1.85 / 개
데이터시트 보기 →MKL03Z8VFK4
✅ 드롭인✓ 재고 있음
$1.85 / 개
데이터시트 보기 →MKL03Z8VFG4R
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MKE04Z8VWJ
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MKL02Z32VFK4
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MKL03Z32VFK4 최대 정격 & 전기적 특성
| Core | ARM Cortex-M0+ |
| Family | Kinetis KL03 |
| Maximum CPU Frequency | 48 MHz |
| Program Flash | 32 KB |
| SRAM | 2 KB |
| Operating Voltage Range | 1.71 V to 3.6 V |
| 패키지 | 24-QFN (4x4 mm) |
| 실장 유형 | Surface Mount |
| ADC | 12-bit SAR |
| Communication Interfaces | UART, SPI, I2C, LPUART |
| Timers | Low-power timer, RTC, PWM/TPM |
| 동작 온도 범위 | -40 C to +105 C |
| Low-Power Modes | VLLS0/1/3, LLS, STOP, WAIT, RUN, HSRUN |
| RoHS 상태 | Compliant |
| Lead-Free | Yes |
MKL03Z32VFK4 핀 구성
| 핀 1 | PTA0/IRQ — General-purpose I/O / Interrupt request |
| 핀 2 | PTA1 — General-purpose I/O |
| 핀 3 | PTA2 — General-purpose I/O |
| 핀 4 | PTA4 — General-purpose I/O |
| 핀 5 | PTA5/Reset_b — GPIO / Reset (active low) |
| 핀 6 | PTA6 — General-purpose I/O |
| 핀 7 | PTA7 — General-purpose I/O |
| 핀 8 | PTB0/LLWU_P0 — GPIO / Low-leakage wakeup pin 0 |
| 핀 9 | PTB1 — General-purpose I/O |
| 핀 10 | PTB2 — General-purpose I/O |
| 핀 11 | PTB3 — General-purpose I/O |
| 핀 12 | PTB4 — General-purpose I/O |
| 핀 13 | PTB5 — General-purpose I/O |
| 핀 14 | VSS — Ground |
| 핀 15 | VDD — Power supply (1.71-3.6 V) |
| 핀 16 | PTA3/SWDIO — GPIO / Serial wire debug data |
| 핀 17 | PTA8/SWCLK — GPIO / Serial wire clock |
| 핀 18 | PTA9 — General-purpose I/O |
| 핀 19 | PTA10 — General-purpose I/O |
| 핀 20 | PTA11 — General-purpose I/O |
| 핀 21 | PTB6 — General-purpose I/O |
| 핀 22 | PTB7 — General-purpose I/O |
| 핀 23 | VREFH — ADC reference high |
| 핀 24 | VREFL — ADC reference low |
일반적인 애플리케이션
MKL03Z32VFK4 적합 용도: 6 애플리케이션s: Wearable Fitness and Health Sensors, Ultra-Low-Power Wireless Sensor Nodes, IoT Endpoints and Edge Sensors, Smart Home and Building Automation Nodes, Battery-Powered Portable Instrumentation, Industrial Sensor Transmitters.
Wearable Fitness and Health Sensors
The MKL03Z32VFK4's sub-100 uA/MHz active current, VLLS0 deep-sleep mode drawing only a few hundred nanoamps, and Cortex-M0+ deterministic interrupt response make it a strong fit for wearable fitness bands, heart-rate sensors, and step-counters that spend over 99% of their life in deep sleep. The 24-QFN (4x4 mm) package fits inside a wristband or chest-strap module where PCB area is at a premium, and the 32 KB flash comfortably holds a Bluetooth Low Energy beacon stack plus a sensor-fusion library. Placed as the central MCU between a coin-cell and a low-power analog front end, the KL03 wakes on GPIO, samples, transmits via LPUART/LPSPI, and returns to VLLS0 within milliseconds - extending battery life to multiple months on a single CR2032.
추천
Ultra-Low-Power Wireless Sensor Nodes
The MKL03Z32VFK4 is ideal for Zigbee, Thread, BLE, or sub-GHz sensor nodes that must operate for years on a coin cell or harvested energy. With the KL03's VLLS0 mode drawing nanoamps and 48 MHz Cortex-M0+ providing sufficient compute for stack management and sensor processing, designers can architect end-nodes that wake, sense, transmit, and return to sleep within milliseconds. The 24-QFN (4x4 mm) package integrates directly next to sub-GHz transceivers such as the SX1276 or BLE SoCs in multi-chip modules. Use case: a battery-powered temperature/humidity node that wakes every 60 seconds, transmits a 16-byte packet over SPI to a companion radio, and returns to VLLS0, achieving >5-year battery life on two AA cells.
추천
IoT Endpoints and Edge Sensors
For IoT endpoints that require deterministic local control plus secure cloud connectivity through a companion radio, the MKL03Z32VFK4 offers a compelling blend of low cost, small footprint, and NXP's Kinetis SDK ecosystem. The 12-bit SAR ADC and analog comparator enable direct sensor interface without an external ADC IC. Place the KL03 between a 3.3 V LDO and an SPI-attached Wi-Fi/BLE module; the KL03 handles local processing while the radio handles transport. With 32 KB flash and the MCUXpresso toolchain, developers can implement MQTT-SN, LoRaWAN, or BLE GATT services with minimal external components.
추천
Smart Home and Building Automation Nodes
Building automation devices such as battery-powered door/window sensors, occupancy detectors, and HVAC wireless thermostats benefit from the MKL03Z32VFK4's combination of small 24-QFN package, VLLS0 deep-sleep, and on-chip 12-bit ADC for direct sensor conditioning. The Cortex-M0+ core runs HVAC control loops at sub-microsecond latency while the device normally sleeps. Placed at the network edge with a Zigbee or Thread radio, the KL03 acts as the application processor, while the radio SoC handles mesh networking. The Kinetis SDK's peripheral drivers and FreeRTOS port allow rapid development of standards-compliant building-automation firmware.
추천
Battery-Powered Portable Instrumentation
Handheld multimeters, portable gas detectors, and medical point-of-care devices leverage the MKL03Z32VFK4's low active current and deterministic Cortex-M0+ performance for measurement and display driving. The 12-bit ADC delivers sufficient resolution for basic measurements, and the LPUART allows low-speed debug without disturbing low-power operation. Place the KL03 between a lithium-coin-cell and a segmented LCD or OLED display; use the on-chip low-power timer for periodic measurement while the MCU sleeps. Kinetis SDK support enables rapid development of IEC 60730-compliant firmware for safety-critical portable devices.
추천
Industrial Sensor Transmitters
Loop-powered 4-20 mA sensor transmitters, wirelessHART adapters, and field-mount vibration sensors benefit from the MKL03Z32VFK4's industrial operating temperature range (-40 C to +105 C) and ultra-low sleep current for loop-powered operation. The 32 KB flash is sufficient for HART or WirelessHART protocol stacks, and the 24-QFN (4x4 mm) package fits inside standard industrial sensor housings. Place the KL03 between a 24 V loop interface and a vibration/temperature sensor chain; the 12-bit ADC digitizes the sensor signal while the MCU runs protocol stacks over SPI-attached modems. Industrial-grade ESD and EMI robustness of the Kinetis L series simplifies IEC 61000-4 compliance.
추천
추천 제품 요약
엔지니어링 참조 데이터: MKL03Z32VFK4 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MKL03Z32VFG4 | MKL03Z8VFK4 | MKL03Z8VFG4R | MKE04Z8VWJ | MKL02Z32VFK4 |
|---|---|---|---|---|---|---|
| Package | 24-QFN (4x4 mm) | 16-QFN | 24-QFN (4x4 mm) - same | 16-QFN | 20-WLCSP | 24-QFN (4x4 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Max CPU Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Program Flash | 32 KB | 32 KB | 8 KB (-75%) | 8 KB (-75%) | 8 KB (-75%) | 32 KB (same) |
| SRAM | 2 KB | 2 KB | 2 KB | 2 KB | 1 KB (-50%) | 4 KB (+100%) |
| Operating Voltage | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 2.7 V to 5.5 V | 1.71 V to 3.6 V |
| Package Pin Count | 24 | 16 | 24 | 16 | 20 | 24 |
주요 차별점
- Smallest footprint in the Kinetis L series (vs MKL03Z32VFG4)
- Largest flash in the 24-QFN KL03 line (vs MKL03Z8VFK4)
- Best-in-class VLLS0 deep-sleep current (vs MKL02Z32VFK4)
설계 노트
Estimated: average current consumption in a typical 1% duty-cycle IoT node (wake every 60 s, sample, transmit, return to VLLS0) is dominated by sleep current. With the KL03 VLLS0 sleep of approximately 0.5 uA and active current of approximately 4 mA at 48 MHz for 5 ms, the average is about 1.7 uA - giving >5 years of life on a 220 mAh CR2032 coin cell. Always include a 100 nF decoupling capacitor within 3 mm of each VDD/VSS pin pair.
The 24-QFN (4x4 mm) package has an exposed thermal pad on the underside that MUST be soldered to a copper ground pour for electrical performance and thermal dissipation. Use 0.1 mm via array (8-12 vias) under the pad stitched to the bottom ground plane to maximize heat sinking. Keep high-speed SWD traces (SWDIO, SWCLK) under 50 mm and avoid routing them near analog ADC inputs to prevent digital-noise coupling into the 12-bit ADC.
Do not operate the device above 48 MHz core clock - exceeding this causes flash wait-state violations and undefined behavior. Do not exceed 3.6 V on VDD even momentarily; the on-chip voltage regulator has no over-voltage clamp. When migrating code from the KL02 to the KL03, reconfigure any GPIO that previously used the KL02's specific analog channels - the KL03 has different peripheral muxing on shared pins and incorrect muxing will silently break UART, SPI, and ADC functionality.
Estimated: at 48 MHz core and 3.6 V supply, the KL03 dissipates approximately 14 mW (typical active current 4 mA x 3.6 V). With the 24-QFN 4x4 mm footprint soldered to a 1 square inch 2-oz copper pour, theta_JA is approximately 80 C/W, yielding a 1.1 C temperature rise above ambient - well within the 105 C maximum operating junction temperature. No external heatsink is required for any normal MCU operating mode.
규정 준수 정보
Standard NXP Kinetis KL03 is not AEC-Q100 qualified - use the KEAZ automotive sub-family for AEC-Q100. RoHS and REACH compliance per NXP product page; halogen-free status not explicitly published.