마이크로컨트롤러

제품 (18719)

ATSAMD20G15A-MUT - 32KB Flash ARM Cortex-M0+ MCU | Microchip
ATSAMD20G15A-MUT

ATSAMD20G15A-MUT - 32KB Flash ARM Cortex-M0+ MCU | Microchip

The Microchip ATSAMD20G15A-MUT is an ARM Cortex-M0+ based 32-bit microcontroller from the SAM D20 family, integrating 32KB of Flash and 4KB of SRAM, running at up to 48 MHz, in a 48-pin QFN package with exposed pad. It is designed for low-power, high-performance embedded applications in home automation, consumer, metering, and industrial segments. What is an ARM Cortex-M0+ microcontroller? An ARM Cortex-M0+ microcontroller is a 32-bit reduced instruction set computing (RISC) MCU built on the ARMv6-M architecture, optimized for energy efficiency and deterministic interrupt response. The Cortex-M0+ sits at the entry level of the ARM Cortex-M family (M0/M0+ -> M3/M4 -> M7) and targets applications that need 32-bit processing, low active power, and deep sleep currents measured in nanoamps. Within the broader system hierarchy it belongs to embedded microcontrollers -> microcontrollers -> microprocessors & MCUs -> semiconductors. Microchip's SAM D20 family is the company's mainstream Cortex-M0+ lineup, bridging 8-bit PIC and Cortex-M3/M4 designs. Key features of the ATSAMD20G15A-MUT include the Cortex-M0+ core reaching 2.14 CoreMark/MHz, 32KB Flash, 4KB SRAM, an SERCOM-configurable peripheral set for I2C/SPI/UART, a 12-bit ADC, a 10-bit DAC, and multiple sleep modes that drop quiescent current to microamp levels. The device operates from 1.62V to 3.6V across the -40C to +85C industrial temperature range. Technically, the device implements single-cycle 32-bit hardware multiply, a Nested Vectored Interrupt Controller (NVIC), and Microchip's Atmel START / MPLAB X IDE toolchain support. The 48-QFN exposed pad enhances thermal dissipation for sustained 48 MHz operation. Typical applications include smart-home sensor nodes, battery-powered metering devices, industrial control modules, and consumer HMI peripherals where low-power sleep and Cortex-M0+ code density provide meaningful BOM savings. When designing with this MCU, choose decoupling capacitors sized to peak SERCOM switching currents and confirm exposed-pad soldering to maximize thermal performance. The 48-QFN package requires careful PCB land pattern design to avoid manufacturing defects. This page synthesizes distributor pricing, drop-in alternatives within the SAM D20 family, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATSAMD20G15B-AUT - 48MHz Cortex-M0+ MCU, 32KB Flash | Microchip
ATSAMD20G15B-AUT

ATSAMD20G15B-AUT - 48MHz Cortex-M0+ MCU, 32KB Flash | Microchip

The Microchip Technology ATSAMD20G15B-AUT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20G family, integrating 32KB of Flash and 4KB of SRAM, running at up to 48 MHz core frequency, and housed in a 48-pin TQFP (7x7 mm) package. The device operates from a single 1.62V to 3.63V supply and includes 6 SERCOM (serial communication) interfaces, a 12-bit ADC, 10-bit DAC, and a full-speed USB 2.0 device controller, enabling compact, low-power connected designs in industrial and consumer segments. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O onto one silicon die. The ARM Cortex-M0+ is the smallest and most energy-efficient member of the ARM Cortex-M family, optimized for deterministic 32-bit performance at minimum power and code density. The ATSAMD20G15B-AUT sits within the broader hierarchy: Cortex-M0+ -> ARM 32-bit core -> embedded MCU -> semiconductor. Microchip's SAM D20 family further specializes this core for low-power, mixed-signal IoT endpoints with the company's proprietary SleepWalking peripherals and event system. Key features of the ATSAMD20G15B-AUT include six SERCOM modules (each software-configurable as USART, I2C, or SPI), up to 38 general-purpose I/O pins, a 12-channel 350 ksps 12-bit ADC with hardware oversampling, a 10-bit 350 ksps DAC, two analog comparators, and a Peripheral Touch Controller (PTC) supporting capacitive touch sensing. The device integrates a full-speed USB 2.0 device port with on-chip transceiver, a Real-Time Clock (RTC) with calendar mode, and a 32 kHz oscillator plus 8 MHz and 48 MHz internal oscillators for flexible clocking without external crystals. At the architecture level, the ATSAMD20G15B-AUT leverages the Cortex-M0+ v6-M instruction set with a single-cycle I/O port and a low-latency interrupt controller (NVIC) supporting 32 IRQ lines. The Microchip Atmel Studio / MPLAB X ecosystem provides a mature toolchain via ARM GCC, and the part is supported by Atmel START code generation and ASF (Advanced Software Framework) drivers. A 2KB independent Flash read/write region is reserved for EEPROM emulation via the NVM controller, simplifying parameter storage. Typical applications include home automation nodes, smart metering endpoints, consumer appliances (washing machines, coffee machines), low-cost sensor hubs, capacitive touch user interfaces, and industrial control peripherals. The combination of USB device, multiple SERCOM, and ADC/DAC in a small TQFP-48 footprint makes it a strong fit for sensor reading + wired connectivity in a single chip. The -AUT suffix denotes industrial temperature range (-40C to +85C) and tape-and-reel packaging. When designing with this part, allocate PCB area for a 32.768 kHz watch crystal if RTC accuracy below 1% is required, and provide a 1uF + 100nF decoupling network within 3 mm of each supply pair. Take care that the USB DM/DP trace impedance is 90 ohms differential and that the VBUS pin uses the correct divider when self-powered, per the Microchip datasheet. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATSAMD20G15B-MU - 32KB Flash Cortex-M0+ MCU 48MHz | Microchip
ATSAMD20G15B-MU

ATSAMD20G15B-MU - 32KB Flash Cortex-M0+ MCU 48MHz | Microchip

The Microchip Technology ATSAMD20G15B-MU is a 32-bit ARM Cortex-M0+ flash microcontroller running at up to 48 MHz, integrating 32 KB of Flash and 4 KB of SRAM in a 48-pin VQFN-EP (7x7 mm) package. It belongs to the SAM D20 family of low-power, high-performance microcontrollers aimed at home automation, consumer, metering, and industrial applications. A microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory, data memory, and programmable I/O peripherals. The Cortex-M0+ core inside the ATSAMD20G15 is one of the most energy-efficient ARM cores available, featuring single-cycle hardware multiplication, a 2-stage pipeline, and a deeply integrated Nested Vector Interrupt Controller (NVIC). Microcontrollers in this class belong to the broader hierarchy of embedded processors -> ARM Cortex-M -> Cortex-M0+ -> Microchip SAM D20. Engineers select Cortex-M0+ MCUs when deterministic real-time response, ultra-low sleep current, and a compact footprint are critical. Key features of the ATSAMD20G15B-MU include 32 KB Flash, 4 KB SRAM, up to 48 MHz CPU clock, six SERCOM interfaces configurable as UART/SPI/I2C, a 12-bit ADC with up to 350 ksps, 10-bit DAC output, full-speed USB 2.0 device, and a 16-bit timer/counter. The device operates from 1.62 V to 3.6 V and supports the industrial temperature range of -40 °C to +85 °C. Technically, the device uses Microchip's proprietary low-power picoPower technology with multiple sleep modes, an integrated 32 kHz RTC, and event system for inter-peripheral signaling without CPU wake-up. Its single-cycle I/O bus reduces latency between peripherals and the core. Typical applications include smart-home sensor nodes, IoT edge devices, battery-powered metering, low-cost consumer HMI, USB HID peripherals, and industrial control modules. The integrated 12-bit ADC makes it well-suited for analog sensor reading. Designers should note that the VQFN-EP package requires a properly sized exposed-pad land pattern with multiple thermal vias for reliable operation and PCB heat spreading. Decoupling capacitors (100 nF + 1 µF) must be placed as close to VDD pins as possible. This page synthesizes distributor pricing from DigiKey/Mouser, drop-in alternatives drawn from the SAM D20 family, and practical design notes not found in the standalone Microchip datasheet, providing an information-gain view for hardware engineers evaluating Cortex-M0+ solutions.

견적 요청 문의하기
ATSAMD20G15B-MUT - 32KB Flash Cortex-M0+ MCU 48-QFN | Microchip
ATSAMD20G15B-MUT

ATSAMD20G15B-MUT - 32KB Flash Cortex-M0+ MCU 48-QFN | Microchip

The Microchip Technology ATSAMD20G15B-MUT is a 32-bit ARM Cortex-M0+ based flash microcontroller (SAM D20G family) featuring 32KB of flash, 4KB of SRAM, and a maximum CPU clock of 48 MHz, housed in a 48-pin 7x7 mm QFN package with exposed thermal pad. It is designed for low-power, high-performance embedded applications and ships as a tape-and-reel (T/R) variant with industrial temperature grade (-40C to +85C). A microcontroller (MCU) is an integrated circuit that combines a CPU core, program and data memory, peripherals, and I/O on a single silicon die. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor core, typically used as a stepping stone between 8/16-bit legacy MCUs and higher-end Cortex-M3/M4 parts. The SAM D20G family sits within Microchip's broader SAM (Smart ARM) portfolio, bridging tiny AVR/PIC parts and higher-end Cortex-M based SAM S70/E70 devices. Key features of the ATSAMD20G15B-MUT include the SERCOM (Serial Communication Interface) module which can be configured as UART, SPI, or I2C; a 12-bit ADC with up to 200 ksps throughput; a 10-bit DAC; and an Event System for inter-peripheral signaling without CPU wake-up. Power consumption is rated at down to sub-uA in deep-sleep backup mode, with multiple SleepWalking peripheral channels. The device implements Microchip's proprietary Atmel Start code-generation framework and is fully supported by Atmel Studio 7, MPLAB X IDE, and Microchip Studio for GCC-based development. The Cortex-M0+ core includes the ARMv6-M instruction set, hardware multiply (32-bit result in one cycle), and a single-cycle I/O port. Typical applications include home automation endpoints, smart metering nodes, consumer electronics HIDs, industrial sensor interfaces, and low-power IoT edge nodes where battery life and small footprint outweigh raw CPU throughput. The SERCOM-rich architecture also simplifies BOM reuse across UART, SPI, and I2C sensor variants. When designing with this part, budget decoupling capacitance (100 nF X7R + 1 uF X5R minimum on each VDD pin) and follow Microchip's QFN land pattern with a contiguous ground pad beneath the EP for thermal dissipation. Programming is supported through the SWD interface, requiring PA30 (SWDCLK) and PA31 (SWDIO) to be reserved or strapped appropriately. This page synthesizes distributor pricing, drop-in pin-compatible alternatives within the SAM D20 family, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
ATSAMD20G16A-AN - ARM Cortex-M0+ MCU, 64KB Flash, 48TQFP | Microchip
ATSAMD20G16A-AN

ATSAMD20G16A-AN - ARM Cortex-M0+ MCU, 64KB Flash, 48TQFP | Microchip

The Microchip Technology ATSAMD20G16A-AN is an ARM Cortex-M0+ based 32-bit microcontroller delivering up to 48 MHz performance with 64 KB Flash and 8 KB SRAM, housed in a 48-pin TQFP package. It integrates six SERCOM configurable serial interfaces (I2C/SPI/UART), a 12-bit ADC with up to 350 ksps throughput, a 10-bit DAC, and a 256-channel Peripheral Touch Controller for capacitive sensing. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, and programmable peripherals. The Cortex-M0+ is ARM's most energy-efficient 32-bit core, optimized for deterministic interrupt response and low active/sleep power. The SAM D20 family extends this foundation with Microchip's Atmel-era peripheral set including SERCOM, Event System, and PTC, making it a popular choice for cost-sensitive embedded designs. Key features of the ATSAMD20G16A-AN include 38 programmable I/O pins, an operating voltage range of 1.62V to 3.63V, brown-out detect, power-on reset, watchdog timer, RTC with calendar mode, and a full-speed USB 2.0 device interface in higher-pin variants. The 12-bit ADC offers up to 16 analog inputs with hardware averaging, while the 10-bit DAC provides buffered analog output for sensor excitation or waveform generation. The SAM D20 architecture uses a single-cycle hardware multiplier and a Nested Vectored Interrupt Controller (NVIC) for deterministic latency. The Event System allows peripherals to communicate without CPU intervention, enabling energy-efficient operation by keeping the CPU in sleep mode while data flows autonomously. The PTC peripheral scans up to 256 mutual-capacitance or self-capacitance electrodes for touch interfaces without external components. Typical applications include home automation controllers, smart metering, low-power wireless sensor nodes, consumer electronics with touch interfaces, and industrial HMI panels. The wide 1.62V-3.63V supply range and integrated peripherals reduce BOM cost in battery-powered systems where multiple voltage rails are undesirable. When designing with the ATSAMD20G16A-AN, ensure that firmware is loaded via SWD or the factory-programmed boot loader; Microchip's Atmel Studio 7 and MPLAB X IDE both support this part. Decoupling: place 100 nF X7R ceramics on each VDD pin and a 4.7 uF bulk capacitor on the main rail. This page consolidates verified distributor pricing, drop-in alternatives, and PCB-level design guidance derived from Microchip application notes — information not aggregated on the manufacturer datasheet alone.

견적 요청 문의하기
ATSAMD20G16A-AU - 48MHz ARM Cortex-M0+ MCU 64KB Flash | Microchip
ATSAMD20G16A-AU

ATSAMD20G16A-AU - 48MHz ARM Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip Technology ATSAMD20G16A-AU is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20G family, featuring 64KB of Flash, 8KB of SRAM, and a maximum CPU clock of 48MHz in a 48-pin TQFP (7x7 mm) package. It integrates the Cortex-M0+ core with the Microchip peripheral touch controller (PTC), 6 SERCOM interfaces, a 12-bit 1MSPS ADC, and multiple 16-bit timers, making it a compact, low-power general-purpose MCU. What is a Cortex-M0+ microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and configurable peripherals. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor, optimized for deterministic interrupt response and ultra-low power embedded designs. MCUs like the ATSAMD20G16A-AU sit within the broader taxonomy: Cortex-M0+ -> ARM Cortex-M family -> 32-bit RISC processor -> microcontroller -> embedded system -> semiconductor. The SAM D20 family targets home automation, consumer, metering, and industrial applications where small footprint and peripheral integration matter most. Key features of the ATSAMD20G16A-AU include six SERCOM (serial communication) modules, each configurable as UART, SPI, or I2C, plus a 12-bit 1MSPS ADC with up to 14 channels, two 16-bit timers/counters, a real-time clock, and the Peripheral Touch Controller (PTC) for capacitive sensing. The device operates from 1.62V to 3.63V supply, supports Sleep, Idle, and Standby modes, and provides a typical active current under 4 mA at full 48MHz clock, achieving 2.14 CoreMark/MHz energy efficiency. Technically, the SAM D20G uses a single-cycle hardware multiplier and a 2-stage pipeline to deliver high code density while maintaining the low gate count of the M0+ core. Its event system allows peripherals to trigger one another without CPU involvement, offloading work and reducing wake events. The integrated PTC uses the QTouch library to support capacitive buttons, sliders, and proximity sensing directly without external components. Typical applications include capacitive touch user interfaces, smart-home sensor hubs, low-power wireless sensor nodes, industrial control panels, and battery-powered metering devices. Its 1MSPS ADC makes it suitable for fast data-acquisition tasks, while its SERCOM flexibility simplifies multi-protocol bridging. Designers also favor the SAM D20G for portable consumer products where Sleep-mode current and small package size drive BOM decisions. When designing with this device, allocate the 48-pin TQFP footprint carefully because it shares GPIO and peripheral mapping with the SAM D20E and SAM D20J series. Plan for an external 32.768kHz crystal if accurate RTC timing is required, and confirm supply voltage headroom when using the ADC at full 1MSPS sampling rate. This page synthesizes distributor pricing, drop-in alternatives within the SAM D20 family, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
ATSAMD20G16A-AUT - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip
ATSAMD20G16A-AUT

ATSAMD20G16A-AUT - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip ATSAMD20G16A-AUT is an ARM Cortex-M0+ based 32-bit microcontroller from the SAM D20G family, operating at up to 48 MHz with 64 KB of Flash and 8 KB of SRAM in a 48-pin TQFP (7x7 mm) industrial-grade package. It integrates the Cortex-M0+ core with single-cycle multiplier, Nested Vectored Interrupt Controller (NVIC), and Microchip's SERCOM (Serial Communication Interface) peripheral set configurable as UART/USART, SPI, or I2C. What is a microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals such as timers, ADC, communication interfaces, and GPIO. The Cortex-M0+ family is the smallest and most energy-efficient member of the ARM Cortex-M processor lineup, designed for deterministic embedded control in cost- and power-sensitive applications. Microcontrollers sit within the broader taxonomy of: MCU -> embedded processor -> semiconductor -> integrated circuit. Key features of the ATSAMD20G16A-AUT include 64 KB Flash, 8 KB SRAM, 6 SERCOM channels, a 12-bit 350 ksps ADC with up to 20 channels, two 16-bit Timer/Counters (TC), a 32-bit Real-Time Timer (RTC) with calendar mode, and a full-speed USB 2.0 device controller. The device operates from 1.62 V to 3.63 V and supports sleepwalking peripherals that wake the CPU only when a peripheral event requires service, minimizing average current draw in battery-powered designs. Architecturally, the ATSAMD20G16A-AUT uses an advanced 65 nm process and Microchip's proprietary peripheral event system that allows peripherals to trigger one another without CPU intervention. The integrated 48 MHz digital frequency-locked loop (DFLL48M) provides a stable clock source that can be referenced to a 32.768 kHz crystal, enabling USB Full-Speed operation without an external high-frequency oscillator. Typical applications include home automation nodes, smart metering endpoints, consumer electronics with USB device interfaces, industrial sensor hubs, low-cost IoT edge devices, and human-machine interface (HMI) controllers. The combination of Cortex-M0+ efficiency and full-speed USB makes it especially attractive for HID-class peripherals, USB-to-UART bridges, and small graphics terminals. When designing with this part, choose decoupling capacitors per the datasheet (typically 100 nF on each VDD pin) and ensure SWD signals (SWDIO, SWCLK) are routed away from high-frequency switching nodes. The IDCODE-based Cortex-M0+ debug interface allows programming and debug via Atmel-ICE, MPLAB ICD 4, or compatible third-party tools such as PEmicro. This page synthesizes distributor pricing for the ATSAMD20G16A-AUT, drop-in same-package alternatives from both Microchip's own SAM D family and competing Cortex-M0+ vendors, and practical PCB layout notes not found in the standalone manufacturer datasheet PDF.

견적 요청 문의하기
ATSAMD20G16A-MNT - ARM Cortex-M0+ 48MHz 64KB MCU | Microchip
ATSAMD20G16A-MNT

ATSAMD20G16A-MNT - ARM Cortex-M0+ 48MHz 64KB MCU | Microchip

The Microchip Technology ATSAMD20G16A-MNT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20 family, featuring 64KB of Flash and 8KB of SRAM, operating at up to 48MHz with a 2.14 CoreMark/MHz performance rating, housed in a 48-pin QFN (7x7 mm) package. The device integrates a 14-channel 12-bit Analog-to-Digital Converter (ADC), one 10-bit Digital-to-Analog Converter (DAC), and supports 1.6V to 3.6V operation over the -40C to +105C industrial temperature range. A Cortex-M0+ microcontroller is the smallest and most energy-efficient core in the ARM Cortex-M family, designed for cost-sensitive embedded applications. It occupies the hypernym hierarchy: microcontroller (MCU) -> 32-bit MCU -> ARM Cortex-M -> Cortex-M0+ -> low-power MCU category. The ATSAMD20G16A-MNT belongs to the Atmel SMART SAM D20 series, which is positioned between 8/16-bit legacy MCUs and higher-end Cortex-M3/M4 devices, making it ideal for applications that need modern 32-bit performance at 8-bit cost. Key features include Serial Wire Debug (SWD) interface, Event System for inter-peripheral signaling, six Serial Communication Interfaces (SERCOM) configurable as I2C/SPI/UART, two I2S interfaces, one Full-Speed USB 2.0 device with on-chip transceiver, and a Real-Time Clock (RTC). The device supports Sleep, Idle, Standby, and Backup sleep modes with fast wake-up times, making it suitable for battery-powered applications. The Peripheral Touch Controller (PTC) supports capacitive touch sensing with up to 256 channels. The ATSAMD20G16A-MNT uses a single-cycle hardware multiplier and single-cycle IO access port for deterministic 48MHz operation, achieving 2.14 CoreMark/MHz efficiency. The 48-QFN package with 7x7 mm body and 0.5 mm pitch integrates an exposed thermal pad for improved heat dissipation. The device provides up to 38 programmable I/O pins, all of which support interrupt capability. Typical applications include home automation, smart metering, sensor hubs, low-power IoT edge nodes, consumer electronics HMI, and industrial control peripherals. The wide operating voltage range (1.6V-3.6V) supports direct Li-ion battery connection. The integrated USB 2.0 Full-Speed device makes it well-suited for HID peripherals, CDC virtual COM ports, and USB-powered sensor nodes. When designing with this device, ensure that the VDDCORE pin has proper decoupling and follow the recommended PCB layout for the 48-QFN package. The 6 SERCOM modules provide flexible peripheral mapping, but careful pin assignment is needed to avoid conflicts when using multiple interfaces simultaneously. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design guidance not found in the manufacturer datasheet alone, including cross-package family migration paths within the SAM D20/D21 series.

견적 요청 문의하기
ATSAMD20G16A-MUT - 48MHz Cortex-M0+ MCU, 64KB Flash | Microchip
ATSAMD20G16A-MUT

ATSAMD20G16A-MUT - 48MHz Cortex-M0+ MCU, 64KB Flash | Microchip

The Microchip ATSAMD20G16A-MUT is a 32-bit ARM Cortex-M0+ flash microcontroller in the SAM D20 family, delivering up to 48 MHz core speed with 64 KB Flash and 8 KB SRAM in a 48-pin QFN (7x7 mm) package. It is the industrial/consumer tape-and-reel variant of the ATSAMD20G16A family and is automotive-qualified per the Jotrin listing description, supporting 1.8V/2.5V/3.3V supply rails. A Cortex-M0+ microcontroller (MCU) is a 32-bit ARM-based processor core designed for low-power, cost-sensitive embedded applications. The Cortex-M0+ sits at the entry level of the ARM Cortex-M family and is followed up the hierarchy by Cortex-M0, M3, M4, M7, M33, and M85. Inside Microchip's portfolio, this part belongs to the SAM D20 family of low-power Cortex-M0+ MCUs, which target home automation, consumer, metering, and industrial end-products. Compared with 8-bit PIC MCUs, a Cortex-M0+ brings a 32-bit instruction set, deterministic interrupt handling (NVIC), and Thumb-2 code density that lets engineers run richer protocol stacks (BLE provisioning, LoRa, sub-GHz proprietary) on a single die. Key features of the ATSAMD20G16A-MUT include: 64 KB Flash, 8 KB SRAM, a 12-bit ADC with up to 256-channel Peripheral Touch Controller (PTC), a 10-bit DAC, a 32 kHz RTC, and up to six SERCOM serial-communication modules that can each be configured as USART, I2C, or SPI. The device integrates an internal 32.768 kHz oscillator, a fractional PLL, and an 8-channel Event System for inter-peripheral signaling without CPU load, which is unusual for an entry-level Cortex-M0+ part. Architecturally, the SAM D20 uses a single-cycle hardware multiplier, single-cycle 32-bit multiply-accumulate, and a 2.14 CoreMark/MHz rating (per Atmel datasheet family spec). The 256-channel PTC enables capacitive touch sensing for buttons, sliders, and proximity electrodes without an external touch IC, and the integrated 10-bit DAC can drive audio reference rails or setpoints for closed-loop control. Typical applications include home automation sensor hubs, smart metering (gas/water/electric), industrial HMI panels with capacitive touch, consumer appliances with brushless-DC control, and low-cost IoT end nodes. The wide 1.62V-3.63V supply tolerance and low-power sleep modes (<1 µA typical) make it well-suited to battery-powered deployments such as electronic shelf labels, remote controls, and wearable patches. When designing with the ATSAMD20G16A-MUT, choose the QFN-48 (7x7) land pattern with a continuous EP ground plane and follow Microchip AN2466 layout guidance for the analog supply (VDDANA) decoupling. The PTC touch channels share pins with the ADC, so firmware must decide at build time whether the board uses capacitive touch or analog sampling on each pin. This page synthesizes distributor pricing, drop-in SAM D20 alternatives, and practical design notes that go beyond the manufacturer datasheet, giving engineers a single source for sourcing and second-sourcing decisions.

견적 요청 문의하기
ATSAMD20G16B-AN - 64KB Flash ARM Cortex-M0+ MCU 48MHz | Microchip
ATSAMD20G16B-AN

ATSAMD20G16B-AN - 64KB Flash ARM Cortex-M0+ MCU 48MHz | Microchip

The Microchip ATSAMD20G16B-AN is a 32-bit ARM Cortex-M0+ based microcontroller delivering up to 48 MHz CPU performance with 64KB Flash and 8KB SRAM, housed in a 48-pin TQFP (7x7 mm) package. It operates across a 1.6 V to 3.6 V supply range and supports the industrial -40 C to +105 C temperature grade, with 38 programmable I/O lines and six flexible SERCOM serial communication modules. The device integrates a 12-bit ADC, 10-bit DAC, 256-channel Peripheral Touch Controller (PTC), six 16-bit timers, two analog comparators, and a full-speed USB 2.0 device with on-chip transceiver. Per the Microchip SAM D20 family datasheet, these Cortex-M0+ parts reach 2.46 CoreMark/MHz, providing excellent performance per milliwatt for battery-powered designs. A microcontroller (MCU) is an integrated circuit containing a CPU core, program memory (Flash), data memory (SRAM), and a configurable set of peripherals. The Cortex-M0+ is the smallest and most energy-efficient ARM core, optimized for deterministic interrupt-driven embedded workloads. The SAM D20 family belongs to the Cortex-M0+ microcontroller hypernym hierarchy: ARM Cortex-M0+ -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. Within Microchip's portfolio it sits between tiny 8-bit PIC MCUs and the higher-performance Cortex-M4 SAM D/E families, offering a sweet spot of low active power (under 70 uA/MHz typical) and rich peripheral integration. Key differentiating features include hardware PTC touch support that eliminates external touch ICs in human-interface designs, an on-chip Full-Speed USB 2.0 device eliminating external PHY cost, a 12-bit 350 ksps ADC and 10-bit DAC for sensor signal conditioning, and six SERCOM modules that can each be reconfigured as I2C/SPI/USART. The 48 MHz core plus single-cycle I/O gives deterministic response for motor control loops, while the Event System allows peripherals to trigger each other without CPU intervention, further reducing power. Per the SAM D20 datasheet, low-power Sleep mode typically draws below 1.5 uA with RTC running, enabling multi-year coin-cell operation. Typical applications include home automation sensors, smart metering endpoints, consumer wearables, industrial HMI panels, USB HID peripherals, and Capacitive Touch user interfaces. Industrial-grade qualification makes the part suitable for factory floor controllers operating continuously at elevated ambient temperatures. Designers should plan decoupling (1 uF plus 100 nF near VDDIN/VDDIO), reserve a 32.768 kHz crystal footprint for RTC Sleep modes, and follow Microchip AN2460 layout guidance for clean ADC reference performance. Firmware is generated via MPLAB X IDE with the ASF or MCC framework. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not always present in the manufacturer datasheet.

견적 요청 문의하기
ATSAMD20G16B-ANT - 64KB Flash Cortex-M0+ MCU 48MHz | Microchip
ATSAMD20G16B-ANT

ATSAMD20G16B-ANT - 64KB Flash Cortex-M0+ MCU 48MHz | Microchip

The Microchip Technology ATSAMD20G16B-ANT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20 family, featuring 64KB of flash memory, 8KB of SRAM, and a 48MHz CPU clock, housed in a 48-pin TQFP (7x7 mm) package. This low-power, high-performance MCU integrates a 12-bit ADC, 10-bit DAC, 256-channel Peripheral Touch Controller (PTC), RTC, and six SERCOM (Serial Communication Interface) modules configurable as I2C, SPI, or UART. A microcontroller (MCU) is a single-chip computer containing a processor core, memory, and programmable peripherals. The Cortex-M0+ is the most energy-efficient ARM core, designed for embedded applications where low power and deterministic interrupt response matter more than raw compute. MCUs sit at the heart of nearly every connected product - from home appliances to industrial sensors - forming the lowest tier of the embedded computing hierarchy (MCU -> SoC -> microprocessor -> computer system). Key features of the ATSAMD20G16B-ANT include 64KB flash, 8KB SRAM, 48MHz CPU, 12-bit ADC, 10-bit DAC, 256-channel PTC for capacitive touch, RTC with calendar mode, six SERCOM modules, and an operating voltage range of 1.62V to 3.63V. The device offers multiple low-power modes (Idle, Standby, Backup, and Off) with typical active current under 5 mA at full CPU speed, making it well suited for battery-powered applications. The ATSAMD20G16B is built on a low-leakage process optimized for energy efficiency, integrating a high-precision 32kHz RTC oscillator and an 8MHz system oscillator with PLL. Its Event System allows inter-peripheral signaling without CPU intervention, freeing the M0+ core for application code. Six SERCOM channels provide flexible mixed-protocol connectivity, and the 12-bit ADC delivers up to 350ksps conversion rate for sensor reading. Typical applications include home automation nodes, consumer electronics with capacitive touch interfaces, smart metering, IoT sensor endpoints, industrial control peripherals, and low-power wireless sensor platforms. The wide 1.62-3.63V supply range and deep sleep currents below 5 uA enable multi-year coin-cell battery operation in remote sensor nodes. When designing with this part, note that the ATSAMD20G16B-ANT ships in 48-TQFP requiring standard SMT assembly, supports SWD debugging via Atmel/Microchip Studio or MPLAB X, and uses the Atmel/Microchip START code configurator for rapid peripheral initialization. Pair it with a 32.768kHz crystal for RTC accuracy and follow Microchip application notes for low-power design patterns. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, providing a single-source engineering reference for the ATSAMD20G16B-ANT.

견적 요청 문의하기
ATSAMD20G16B-AUT - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip
ATSAMD20G16B-AUT

ATSAMD20G16B-AUT - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip Technology ATSAMD20G16B-AUT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20G family, operating at up to 48 MHz with 64 KB of Flash and 8 KB of SRAM, housed in a 48-pin TQFP (7x7 mm) industrial-grade package. Key headline parameters are 64 KB Flash, 8 KB SRAM, 48 MHz core clock, and a 1.62 V to 3.6 V supply range, with operating temperature from -40 °C to +85 °C. What is a Cortex-M0+ microcontroller? An ARM Cortex-M0+ microcontroller is a 32-bit reduced instruction set computing (RISC) core designed for ultra-low-power embedded applications, sitting at the low-power end of the Cortex-M family below Cortex-M3/M4/M7. Microcontrollers are single-chip computers integrating CPU core, non-volatile Flash program memory, volatile SRAM, and a broad set of peripherals such as timers, ADC/DAC, communication interfaces (SERCOM), and general-purpose I/O. In the broader taxonomy: Cortex-M0+ -> ARM Cortex-M -> 32-bit MCU -> microcontroller -> integrated circuit -> semiconductor. The SAM D20 family is Microchip's mainstream low-power Cortex-M0+ line, bridging 8-bit AVR/PIC customers into 32-bit ARM designs. Key features of the ATSAMD20G16B-AUT include a 12-bit ADC with up to 14 channels, a 10-bit DAC, six SERCOM modules configurable as UART/SPI/I2C, a 24-bit Timer/Counter for control applications, a 256-channel Peripheral Touch Controller (PTC), a Real-Time Clock (RTC), and full-speed USB device support. The device is designed for low-power operation with multiple Sleep modes and an event system for CPU-independent peripheral communication. Architecturally, the SAM D20G16B uses a single-cycle hardware multiplier, a Nested Vector Interrupt Controller (NVIC), and Microchip's Atmel START/MPLAB X ecosystem. The integrated SERCOM blocks are highly flexible - each can be reconfigured at runtime among USART, SPI, and I2C, allowing designers to match the silicon to varied peripheral needs without changing hardware. Typical applications include home automation, smart consumer devices, industrial sensor nodes, IoT endpoints, low-cost metering, and human-machine interface (HMI) modules. The wide operating voltage range (1.62 V to 3.6 V) and low-power modes also make it well suited for battery-powered designs. Design consideration: choose the TQFP-48 package when a hand-solderable footprint or socketed prototype is required; use the QFN-48 (SAM D20G18A-MU family) for space-constrained designs. Programming and debug are done via the SWD interface - reserve the SWDIO/SWDCLK pins or plan for board rework. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
ATSAMD20G16B-MNT - 48MHz ARM Cortex-M0+ MCU, 64KB Flash | Microchip
ATSAMD20G16B-MNT

ATSAMD20G16B-MNT - 48MHz ARM Cortex-M0+ MCU, 64KB Flash | Microchip

The Microchip ATSAMD20G16B-MNT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20G family, delivering up to 48 MHz CPU clock with 64 KB of flash and 8 KB of SRAM, housed in a 48-pin QFN (7x7 mm) package with exposed thermal pad. It operates from 1.62 V to 3.6 V and targets a wide range of home automation, consumer, metering, and industrial applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one die. The ARM Cortex-M0+ is the smallest and most energy-efficient ARMv6-M core, designed for deterministic embedded control with a 2-stage pipeline, Thumb-2 instruction set, and micro trace buffer. Within the MCU taxonomy, this part sits in the Cortex-M0+ -> ARM Cortex -> 32-bit MCU -> microcontroller -> semiconductor hierarchy, optimized for low-power deterministic tasks. Key features include 64 KB (64K x 8) flash, 8 KB SRAM, an integrated 12-bit ADC, a 10-bit DAC, six SERCOM (serial communication) interfaces configurable as UART/SPI/I2C, a 256-channel Peripheral Touch Controller (PTC), a real-time clock (RTC), and the standard Microchip SleepWalking peripheral event system. The device supports up to 38 GPIO and operates across the industrial temperature range of -40 C to +105 C. A built-in 32 kHz internal oscillator and 8 MHz DFLL allow the core to run at full 48 MHz without external crystals, reducing BOM cost. The SAM D20 architecture combines the Cortex-M0+ core with Microchip's Event System, enabling peripherals to trigger one another without CPU intervention - this is the foundation of the device's low-power performance. The PTC peripheral provides robust capacitive touch sensing with up to 256 channels, supporting buttons, sliders, wheels, and proximity sensors through a single die, replacing mechanical switches in harsh environments. Typical applications include home automation controllers (thermostats, smart lighting, appliance HMIs), industrial sensor hubs, low-power wireless sensor nodes paired with sub-GHz or BLE companions, capacitive touch user interfaces, and battery-powered metering devices. The 1.62 V minimum VDD supports direct connection to single-cell Li-ion or 2x AA alkaline chemistries without external regulators. When designing with this device, follow the Microchip schematic checklist: place a 100 nF decoupling capacitor on each VDD pin, connect the exposed pad to a solid ground copper pour, and ensure the SWDIO/SWDCLK lines are length-matched if routing off-board. The -MNT suffix indicates tape-and-reel packaging with the standard QFN 7x7 mm land pattern, while the -MUT (trays) and -MN (lower-temperature) suffixes share the same pinout.

견적 요청 문의하기
ATSAMD20G16B-MU - 48MHz ARM Cortex-M0+ MCU 64KB Flash | Microchip
ATSAMD20G16B-MU

ATSAMD20G16B-MU - 48MHz ARM Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip Technology ATSAMD20G16B-MU is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20G family, featuring 64KB of flash memory and 8KB of SRAM, operating at up to 48 MHz, in a 48-pin QFN (7x7 mm) package with exposed thermal pad. The device integrates the Cortex-M0+ core with a single-cycle hardware multiplier and a high-performance peripheral bus, providing efficient deterministic execution for embedded control applications. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (flash), data memory (SRAM), and integrated peripherals such as timers, communication interfaces, and analog blocks. The SAM D20 family sits within Microchip's broader portfolio of ARM Cortex-M microcontrollers (Cortex-M0+ -> Cortex-M family -> ARM architecture -> 32-bit RISC processor), positioning this device as a low-power, high-performance tier suitable for general-purpose embedded designs. Key features include 64KB flash with ECC and 8KB SRAM, a 12-bit 350 ksps analog-to-digital converter (ADC) with up to 14 channels, two 16-bit timers/counters for PWM and capture, multiple SERCOM interfaces supporting I2C, SPI, and UART, and a full-speed USB 2.0 device interface on selected variants. Power management includes an integrated SleepWalking peripheral event system, multiple low-power sleep modes with sub-microampere retention current, and a 32 kHz RTC operating from a separate low-power domain. Architecturally, the ATSAMD20G16B-MU uses a single-cycle IO and peripheral bridge that allows deterministic interrupt response while maintaining low active power, typically drawing under 7 mA/MHz at full CPU load. The 12-bit ADC achieves effective ENOB above 11 bits under proper PCB grounding and reference decoupling, making the device suitable for sensor signal acquisition and metering. Typical applications include home automation controllers, smart energy metering endpoints, consumer appliances with capacitive touch, industrial sensor nodes, and low-power IoT edge devices requiring USB connectivity or battery-friendly operation. The wide operating voltage range of 1.62V to 3.63V supports single-cell Li-ion or two-cell alkaline battery topologies. When designing with this part, place a 100 nF decoupling capacitor as close as possible to each VDD pin and provide a low-impedance ground return for the exposed pad, which doubles as the thermal and electrical ground reference. Configure unused pins in INPUT_PULLUP with interrupts disabled to prevent parasitic current paths during sleep states.

견적 요청 문의하기
ATSAMD20G16B-MUT - 32-bit Cortex-M0+ MCU, 64KB Flash, 48-QFN | Microchip
ATSAMD20G16B-MUT

ATSAMD20G16B-MUT - 32-bit Cortex-M0+ MCU, 64KB Flash, 48-QFN | Microchip

The Microchip ATSAMD20G16B-MUT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20G family, integrating 64KB of Flash and 8KB of SRAM, and operating at up to 48 MHz in a 48-pin QFN (7x7 mm) package with an industrial temperature grade (-40C to +85C) and Tape & Reel packaging. It belongs to Microchip's SAM D20 family of low-power, high-performance Cortex-M0+ MCUs designed for home automation, consumer, metering, and industrial applications, with on-chip peripherals including a 12-bit ADC, 10-bit DAC, 256-channel Peripheral Touch Controller (PTC), RTC, and multiple SERCOM configurable serial interfaces. The 'MUT' suffix denotes a 48-pin QFN package in Tape & Reel format. What is an ARM Cortex-M0+ microcontroller? An ARM Cortex-M0+ MCU is a 32-bit microcontroller built around ARM's smallest, most energy-efficient Cortex-M core, which provides Thumb-2 instruction set compatibility, single-cycle I/O access, and a deterministic interrupt controller (NVIC). It sits at the entry point of the Cortex-M family, above 8-bit microcontrollers like 8051/PIC16 and below Cortex-M3/M4/M7 cores in processing capability. The SAM D20G family adds Microchip's proprietary low-power SleepWalking peripherals, Event System, and SERCOM modules on top of the Cortex-M0+ core, positioning it as a power-optimized general-purpose MCU for connected and battery-powered applications. Key differentiating features of the ATSAMD20G16B-MUT include 64KB of in-system programmable Flash with unique 128-bit serial number, 8KB SRAM, 48 MHz maximum CPU speed, six SERCOM channels configurable as USART/UART/SPI/I2C, a 12-bit 350 ksps ADC with up to 20 channels, a 10-bit 350 ksps DAC, and full-speed USB 2.0 device support (note: USB requires external 48 MHz clock). The integrated PTC supports up to 256 touch channels for capacitive touch buttons, sliders, and proximity sensing without external ICs. Architecturally, the SAM D20G16 uses an event-driven design with Microchip's SleepWalking technology that allows peripherals to evaluate incoming data while the CPU remains in sleep mode, waking only on matched events. The Event System routes peripheral triggers across the chip without CPU intervention, enabling ultra-low standby current of under 1 uA with RTC running. The 48 MHz core draws roughly 7 mA/MHz active, allowing long battery life in intermittent-duty applications. Typical applications include smart home sensor nodes (HVAC, door/window sensors), industrial metering (water/gas/electricity), consumer electronics (wearables, toys, appliances), IoT edge nodes, and human-machine interfaces (touch panels, LED control). The wide operating voltage range (1.62V to 3.63V) supports both single-cell Li-ion battery systems and 3.3V regulated industrial rails. Designers should evaluate power budget versus peripheral set carefully: the SAM D20G16 supports SleepWalking and six Sleep modes down to <1 uA backup, but higher-speed ADC sampling or continuous USB operation will dominate the active current budget. Pin-compatible migration paths within the SAM D20/D21 families exist for higher memory or USB integration needs. This page synthesizes distributor pricing, drop-in alternatives within the SAM D20 family, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
ATSAMD20G17A-ANT - 48MHz ARM Cortex-M0+ MCU 128KB Flash 48-TQFP
ATSAMD20G17A-ANT

ATSAMD20G17A-ANT - 48MHz ARM Cortex-M0+ MCU 128KB Flash 48-TQFP

The Microchip Technology ATSAMD20G17A-ANT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20G family, integrating 128KB of Flash and 16KB of SRAM in a 48-pin TQFP (7x7 mm) package rated for the -40C to +105C industrial temperature range. It operates from a 1.62V to 3.63V supply and runs at up to 48MHz, reaching 2.14 CoreMark/MHz, and is supplied in Tape & Reel packaging per the ANT suffix designation. What is a Cortex-M0+ microcontroller? An ARM Cortex-M0+ is an ultra-low-power 32-bit microcontroller core designed for embedded applications; it sits within the broader microcontroller category which includes 8-bit (AVR, PIC), 16-bit (MSP430), and 32-bit (Cortex-M, RISC-V) families, and is a sub-category of microcontrollers which in turn falls under embedded processors, semiconductors, and electronic components. The M0+ architecture delivers Thumb-2 instruction set efficiency while consuming roughly one-third the energy of older 8-bit cores at equivalent throughput. Key features include the Atmel/Microchip Event System for peripheral interoperation without CPU intervention, up to six SERCOM (serial communication) interfaces that can each be independently configured as UART/USART, SPI, or I2C, a 12-bit ADC with up to 350 ksps sampling, a 10-bit DAC, and multiple timer/counter blocks for PWM and capture. The device also features a full-speed USB 2.0 interface, an internal 32kHz and 8MHz oscillator, and a Peripheral Touch Controller for capacitive touch sensing. The SAM D20G architecture uses single-cycle hardware multiplication and a Nested Vector Interrupt Controller (NVIC) for deterministic interrupt response. Its SleepWalking peripheral gating allows peripherals to wake the CPU only when needed, extending battery life in IoT sensor nodes to years on a single coin cell when paired with appropriate duty cycling. Typical applications include home automation gateways, smart metering, industrial sensor hubs, low-power wireless sensor nodes, consumer electronics with capacitive touch UI, and battery-powered IoT devices. The wide operating voltage range and rich peripheral set also make it well suited for portable medical and fitness devices. When designing with this device, ensure the decoupling network uses a 100nF ceramic capacitor close to each VDD pin plus a bulk 4.7uF capacitor; failure to do so may cause ADC noise pickup. Also note that migrating to the SAM D20 family from legacy AVR requires use of the Atmel/Microchip Studio or MPLAB X IDE with the appropriate CMSIS pack. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including engineering trade-offs versus other 48-pin Cortex-M0+ MCUs.

견적 요청 문의하기
ATSAMD20G17A-AU - 48MHz Cortex-M0+ MCU, 128KB Flash | Microchip
ATSAMD20G17A-AU

ATSAMD20G17A-AU - 48MHz Cortex-M0+ MCU, 128KB Flash | Microchip

The Microchip Technology (formerly Atmel) ATSAMD20G17A-AU is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20G family, operating at up to 48 MHz and housed in a 48-pin TQFP (7x7 mm) package. It integrates 128 KB of Flash program memory and 16 KB of SRAM, executes at 2.14 CoreMark/MHz, and supports a 1.62 V to 3.6 V supply range suitable for single-cell Li-ion or 3.3 V regulated rails. An ARM Cortex-M0+ microcontroller is the smallest and most energy-efficient member of the Cortex-M family, designed for deeply embedded, low-power applications that benefit from a 32-bit instruction set, deterministic interrupt handling, and a rich peripheral ecosystem. It sits within the broader taxonomy of microcontrollers -> embedded processors -> semiconductors, and bridges 8-bit PIC/AVR designs to higher-performance Cortex-M3/M4 cores without sacrificing low-power operation. Key features of the ATSAMD20G17A-AU include the SERCOM-configurable serial engine (up to 6 channels of I2C/SPI/UART), a 14-channel 12-bit ADC with up to 350 ksps sampling, one 10-bit DAC, six 16-bit timer/counters, and a full-speed USB 2.0 device port. Its peripheral touch controller (PTC) supports up to 256 channels for capacitive buttons, sliders, and proximity sensing, enabling HMI designs without external touch ICs. The device employs Microchip's proprietary low-power architecture with multiple SleepWalking-enabled peripherals, six power domains, and a typical active current below 4 mA at 48 MHz. The integrated 32.768 kHz oscillator and fractional PLL reduce external component count, and the Event System allows peripherals to trigger each other autonomously without CPU intervention for ultra-low-power sensor polling. Typical applications include home automation gateways, smart energy metering, industrial sensor nodes, consumer wearables, capacitive touch keypads, and low-cost USB HID peripherals. The wide operating temperature range of -40 C to +85 C makes it equally suitable for indoor consumer devices and harsh industrial environments. When designing with this part, allocate the SERCOM channels early because each one is multiplexed across multiple pads, and plan the PTC layout with sufficient ground flood for reliable capacitive touch SNR. Use Microchip's MPLAB X IDE with the SAMD20 DFP to unlock SleepWalking and Event System configuration. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, accelerating your sourcing and schematic review.

견적 요청 문의하기
ATSAMD20G17A-AUT - 48MHz Cortex-M0+ MCU 128KB Flash TQFP-48
ATSAMD20G17A-AUT

ATSAMD20G17A-AUT - 48MHz Cortex-M0+ MCU 128KB Flash TQFP-48

The Microchip Technology ATSAMD20G17A-AUT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20G family, integrating 128KB of Flash and 16KB of SRAM and running at up to 48 MHz in a 48-pin TQFP (7x7 mm) package. The device targets low-power, high-performance embedded applications including home automation, consumer electronics, smart metering, and industrial control, combining the energy efficiency of the Cortex-M0+ core with the peripheral richness of Atmel/Microchip's SAM D20 platform. A microcontroller (MCU) is a single-chip processor that integrates CPU, memory, and peripherals on one die; the ARM Cortex-M0+ is a minimal-footprint 32-bit core optimized for energy-efficient deterministic control, while the SAM D20 family sits one tier below Cortex-M3/M4 parts in the SAM lineup, prioritizing low active current and deep sleep modes over DSP or floating-point performance. Key features of the ATSAMD20G17A-AUT include 128KB of in-application programmable Flash, 16KB SRAM, a six-channel SERCOM-configurable serial interface, a 12-bit ADC and 10-bit DAC, and multiple 16-bit timer/counters. The SERCOM block is the most distinctive feature: each instance can be reconfigured at runtime as I2C, SPI, or USART, allowing the same silicon to serve diverse peripheral mixes without package or pinout changes. The 12-bit ADC achieves up to 300 ksps with hardware averaging and offset compensation. The architecture pairs a single-cycle Cortex-M0+ core with a 2-channel DMA controller and the standard Microchip Event System for inter-peripheral signaling without CPU wake-ups. The integrated FPU-free pipeline keeps deterministic interrupt latency under 12 cycles, and the brown-out detector, watchdog timer, and on-chip 32 kHz RC oscillator reduce external bill-of-materials cost. Typical applications include smart thermostats, sensor hubs, low-cost motor control, USB human-interface devices, battery-powered data loggers, and home-automation gateways. The wide 1.62V to 3.63V operating range supports both single-cell Li-ion and 3.3V regulated rails, while the multiple low-power sleep modes (down to a few microamperes with RTC running) make it well-suited to energy-harvesting designs. When designing in this part, choose decoupling carefully: a single 100 nF plus one bulk 4.7 µF ceramic per supply pin is the standard Microchip reference, and the SERCOM pin mapping must be locked early because pin remapping later in the project typically forces a board spin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the bare manufacturer datasheet.

견적 요청 문의하기
ATSAMD20G17A-MN - 48MHz ARM Cortex-M0+ MCU, 128KB Flash, 48-QFN | Microchip
ATSAMD20G17A-MN

ATSAMD20G17A-MN - 48MHz ARM Cortex-M0+ MCU, 128KB Flash, 48-QFN | Microchip

The Microchip Technology ATSAMD20G17A-MN is a 32-bit ARM Cortex-M0+ based microcontroller from the SAM D20G family, operating at up to 48 MHz and integrating 128 KB of Flash and 16 KB of SRAM in a 48-pin QFN (7x7 mm) with an exposed thermal pad. It is part of the Atmel SMART SAM D20 series, a low-power, high-performance flash MCU platform reaching 2.46 CoreMark/MHz that is pin-compatible across the family and supported by the Atmel/Microchip Studio and Atmel Start software ecosystems. The SAM D20G is built around the ARM Cortex-M0+ core, the smallest and most energy-efficient ARM processor available. It is positioned within the broader taxonomy as follows: ARM Cortex-M0+ -> ARM Cortex-M processor -> 32-bit MCU -> microcontroller -> embedded system. This hierarchy places the part in the Cortex-M0+ tier aimed at cost-sensitive, low-power embedded designs that need the ARM instruction set and toolchain maturity. Key features include the Serial Communication Interface (SERCOM) modules that are highly configurable for I2C, SPI, and UART; a 12-bit ADC with up to 12 channels; 10-bit DAC outputs; and full-speed USB 2.0 Device support on selected variants. The device operates from 1.62 V to 3.63 V across the -40C to +105C industrial temperature range, offers low-power Sleep and Standby modes drawing single-digit microampere currents, and integrates an Event System for inter-peripheral signalling without CPU intervention. The 48-QFN package provides a small footprint suitable for space-constrained designs. Typical applications for the ATSAMD20G17A-MN include home automation endpoints, smart metering, industrial sensor nodes, low-power IoT wearables, consumer human-machine interface (HMI) controllers, and battery-powered data loggers. The combination of Cortex-M0+ processing, generous SRAM, and flexible SERCOM peripherals makes it well suited to designs where simple migration from 8-bit AVR parts is desirable. When designing with this device, engineers should evaluate the SleepWalking and Event System features to minimize MCU wake events, place decoupling capacitors close to the multiple VDD pins, and use the exposed pad (EP) for both thermal dissipation and ground return. The ATSAMD20G17A-MN is identical to the ATSAMD20G17A-MU except for the operating temperature range (105C industrial grade vs. 125C extended grade). This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the standalone manufacturer datasheet.

견적 요청 문의하기
ATSAMD20G17A-MNT - 48MHz Cortex-M0+ MCU 128KB Flash QFN-48 | Microchip
ATSAMD20G17A-MNT

ATSAMD20G17A-MNT - 48MHz Cortex-M0+ MCU 128KB Flash QFN-48 | Microchip

The Microchip Technology ATSAMD20G17A-MNT is a 32-bit ARM Cortex-M0+ flash microcontroller in the SAM D20 family, integrating 128KB of Flash and 16KB of SRAM, operating at up to 48MHz, in a 48-pin QFN (7x7mm) package with industrial -40C to +105C temperature range. The device is specified for 1.6V to 3.6V core/IO supply and delivers 2.14 CoreMark/MHz, balancing deterministic real-time control with deep-sleep power efficiency for battery-aware edge nodes. The -MNT suffix indicates a Matte-Tin lead-free 48-QFN industrial-grade part supplied in Tape & Reel packaging. A 32-bit microcontroller (MCU) is a single-chip processor that integrates CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, ADC, DAC, communication interfaces, and GPIO into one package. ARM Cortex-M0+ cores target energy-efficient embedded applications, sit within the hierarchy of microcontroller -> embedded processor -> semiconductor device, and are widely used wherever deterministic interrupt response and low active/sleep current are required. Key features of the ATSAMD20G17A-MNT include the Cortex-M0+ core with single-cycle I/O access for deterministic GPIO control, 128KB in-system programmable Flash plus 16KB SRAM, an 8-channel event system for hardware-triggered peripheral actions, a 12-bit 350ksps ADC, and SERCOM configurable serial interfaces (I2C/SPI/UART). The integrated 32.768kHz oscillator and DFLL/PLL with 48MHz digital frequency lock loop support crystal-less USB device and accurate timing applications. On the architecture side, the SAM D20 uses a Cortex-M0+ pipeline with single-cycle 32-bit multiplier, NVIC with 4-bit priority, and Microchip's Atmel Start/MPLAB X IDE code base. The 48-QFN package exposes up to 38 GPIO, 6 SERCOM channels, one full-speed USB 2.0 device, and a segmented LCD controller on related variants, providing a balanced peripheral set for connected sensor and HMI designs. Typical applications include home automation control panels, smart energy metering, industrial sensor hubs, consumer wearables, low-power wireless sensor nodes paired with external radios, and small human-machine interfaces using GPIO-driven LED or segment LCD indicators. The Cortex-M0+ plus SERCOM architecture suits designs that need flexible communication with limited PCB area. When designing with this part, allocate the 128KB Flash budget to leave at least 8-16KB for a future bootloader (e.g., for OTA via external SPI Flash), and confirm SERCOM pin mapping against the 48-QFN pad layout before PCB layout because SERCOM functions are multiplexed. Use the on-chip DFLL with a 32.768kHz crystal reference for jitter-sensitive timing. This page combines distributor pricing, pin-compatible alternatives, and practical design notes for the ATSAMD20G17A-MNT, complementing the manufacturer datasheet with cross-brand selection guidance not found elsewhere.

견적 요청 문의하기
ATSAMD20G17A-MU - 48MHz Cortex-M0+ 128KB Flash MCU | Microchip
ATSAMD20G17A-MU

ATSAMD20G17A-MU - 48MHz Cortex-M0+ 128KB Flash MCU | Microchip

The Microchip Technology ATSAMD20G17A-MU is a low-power, high-performance 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20G family, housed in a 48-pin QFN (7x7 mm) package with an exposed thermal pad. It integrates 128KB of in-system programmable Flash, 16KB of SRAM, and runs at up to 48MHz delivering 2.14 CoreMark/MHz, making it suitable for home automation, consumer, metering, and industrial applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals (ADCs, timers, communication interfaces). The Cortex-M0+ architecture is the smallest and most energy-efficient ARM core designed for embedded use, sitting at the bottom of the Cortex-M hierarchy (M0+ -> M0 -> M3/M4 -> M7) and offering Thumb-2 instruction set compatibility. The SAM D20 family belongs to Microchip's broader SMART portfolio of ARM-based microcontrollers, targeting low-power always-on and battery-powered designs where deterministic real-time response and ease of development (via Atmel Studio / MPLAB X) matter more than raw MHz. Key features include 14 channels of 12-bit ADC with up to 350ksps conversion rate, one 10-bit DAC, six SERCOM interfaces configurable as UART/SPI/I2C, a 32-bit Real-Time Counter (RTC), full-speed USB 2.0 device support via the D21 family, and an integrated Peripheral Touch Controller for capacitive buttons. The Event System allows peripherals to communicate without CPU intervention, reducing latency and power. The device supports 1.62V to 3.63V operation and offers multiple low-power Sleep, Standby, and Backup modes with sub-microamp current consumption. The ATSAMD20G17A-MU uses a single-cycle hardware multiplier and a 2-channel DMA controller to offload CPU-intensive tasks. The 48-QFN package exposes a thermal pad for improved heat dissipation in continuous-operation scenarios and is lead-free / RoHS compliant, suitable for industrial temperature range of -40C to +85C. The IC integrates brown-out detection, a watchdog timer, and an on-chip 32kHz ultra-low-power oscillator for accurate timekeeping in deep-sleep states. Typical applications include IoT sensor nodes, smart metering, capacitive-touch user interfaces, HVAC controllers, and low-power wireless sensor hubs. Designers value the SAM D20 family for its deterministic interrupt latency, free MPLAB X IDE / Atmel START code generation, and broad middleware support (FreeRTOS, ASF, Harmony 3). When designing with the ATSAMD20G17A-MU, plan the PCB layout so that the exposed pad is soldered to a continuous ground plane for thermal and electrical performance. Decoupling requires a 100nF ceramic capacitor close to each VDD pin and a bulk 4.7uF capacitor on the main supply rail. Engineers should use Atmel START or MPLAB Harmony 3 code configurators to generate the SERCOM and ADC peripheral initialization, reducing firmware bring-up time. This page synthesizes distributor pricing from DigiKey/Mouser/LCSC, a curated list of drop-in alternatives within the SAM D20 family, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
ATSAMD20G17A-UUT - 128KB Flash Cortex-M0+ MCU, 45-WLCSP
ATSAMD20G17A-UUT

ATSAMD20G17A-UUT - 128KB Flash Cortex-M0+ MCU, 45-WLCSP

The Microchip ATSAMD20G17A-UUT is a low-power, high-performance 32-bit ARM Cortex-M0+ flash microcontroller in the SAM D20 family, housed in a 45-ball WLCSP package and rated for industrial temperature operation. It delivers 128KB of Flash, 16KB of SRAM, and runs at up to 48 MHz while consuming only a few microamps in deep-sleep modes, making it well suited to battery-powered and energy-harvesting designs. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program and data memory, and a rich set of peripherals on a single die. The Cortex-M0+ core used in the SAM D20 family is the smallest and most energy-efficient member of the ARM Cortex-M lineup, designed for deterministic embedded control with a minimal instruction set, hardware single-cycle I/O access, and an integrated Nested Vectored Interrupt Controller (NVIC). Within Microchip's portfolio this part sits in the hierarchy: SAM D20 family -> SAM D microcontroller series -> ARM Cortex-M0+ MCUs -> 32-bit microcontrollers -> embedded ICs. Key features include the SERCOM peripheral architecture that allows each of the up to six serial communication interfaces to be configured as UART, SPI, or I2C, a 12-bit ADC with up to 16 channels, a 10-bit DAC, multiple 16-bit timer/counters, and a full-speed USB 2.0 device interface on selected variants. The on-chip Flash can be programmed via SWD and the device supports a wide 1.62V to 3.6V supply range. The WLCSP-45 package enables compact PCB footprints for wearables and space-constrained IoT modules, with all digital I/O remappable through the peripheral multiplexing layer. Typical applications span home automation sensor nodes, smart metering, consumer HID peripherals, low-cost industrial control, and battery-powered IoT endpoints. Design considerations include careful WLCSP PCB land-pattern and reflow-profile management, providing a clean low-noise analog supply for ADC accuracy, and configuring the SERCOM peripherals via the Microchip ASF or Harmony 3 framework to map signals to the desired pads.

견적 요청 문의하기
ATSAMD20G18A-ANT - ARM Cortex-M0+ 48MHz 256KB Flash MCU | Microchip
ATSAMD20G18A-ANT

ATSAMD20G18A-ANT - ARM Cortex-M0+ 48MHz 256KB Flash MCU | Microchip

The Microchip Technology ATSAMD20G18A-ANT is a 32-bit ARM Cortex-M0+ based flash microcontroller from the SAM D20G family, delivering up to 48MHz CPU clock speed with 256KB of Flash and 32KB of SRAM in a 48-pin TQFP (7x7 mm) industrial-grade package rated for -40C to +105C operation. The device is part of Microchip's popular SAM D20 series and integrates the Cortex-M0+ core with single-cycle hardware multiplier, a 12-channel 12-bit 1 MSPS ADC, two I2C, up to six SERCOM-configurable serial interfaces, and a full-speed USB 2.0 device controller with embedded transceiver. What is a Cortex-M0+ microcontroller? The ARM Cortex-M0+ is the smallest and most energy-efficient member of the Cortex-M processor family, designed for deeply embedded applications that require deterministic real-time behaviour, low active and sleep power, and ease of programming in C. The Cortex-M0+ sits within the broader taxonomy of 32-bit microcontrollers -> ARM Cortex-M -> ARM microcontrollers -> embedded microcontrollers -> integrated circuits, and the SAM D20G family positions itself as an ultra-low-power general-purpose MCU line from Microchip. The single-cycle hardware multiplier and the Microchip SleepWalking peripheral event system are key architectural differentiators. Key features of the ATSAMD20G18A-ANT include the 48MHz Cortex-M0+ core reaching 2.46 CoreMark/MHz, 256KB in-system programmable Flash, 32KB SRAM, full-speed USB 2.0 device with on-chip transceiver, 12-bit 1 MSPS ADC with up to 20 channels, two I2C interfaces, six SERCOM modules configurable as UART/SPI/I2C, six 16-bit timers/counters, RTC with calendar mode, and a wide operating voltage range of 1.62V to 3.63V. The 48-TQFP package provides ample GPIO for typical embedded designs while remaining hand-solderable for prototyping. Architecturally, the SAM D20G uses the Cortex-M0+ with a 2-stage pipeline, a single-cycle 32x32 hardware multiplier (replacing the older 32-cycle software emulation), and a Nested Vectored Interrupt Controller (NVIC) with 32 interrupt sources. The Event System allows peripherals to communicate without CPU intervention, dramatically reducing active power consumption. The Power Manager supports multiple sleep modes (Idle, Standby, Backup) with fast wake-up, and the USB 2.0 Full-Speed controller includes an on-chip transceiver that eliminates the need for an external PHY. Typical applications include USB HID devices, IoT sensor nodes, home automation controllers, consumer electronics, smart metering, industrial control, and human-machine interface (HMI) panels. The combination of USB, ADC, and SERCOM flexibility makes the ATSAMD20G18A-ANT especially well suited to designs where a small footprint MCU must bridge to legacy RS-485 buses, sensors, and USB hosts simultaneously. When designing with this part, ensure that the decoupling network uses at least one 100nF X7R capacitor placed as close as possible to each VDD pin pair, plus a bulk 4.7uF capacitor for the USB 3.3V rail. The full-speed USB DP/DM traces must be routed as a 90-ohm differential pair with length matching within 150 mils. Developers should plan to use the Atmel/Microchip START toolchain or MPLAB X IDE with the DFP (Device Family Pack) and the ASF4 framework to accelerate firmware development. This page synthesizes distributor stock and pricing snapshots, same-family drop-in alternatives, and practical design notes not aggregated on any single distributor or manufacturer page, giving engineers a one-stop reference for the ATSAMD20G18A-ANT.

견적 요청 문의하기
ATSAMD20G18A-AU - 48MHz Cortex-M0+ MCU 256KB Flash | Microchip
ATSAMD20G18A-AU

ATSAMD20G18A-AU - 48MHz Cortex-M0+ MCU 256KB Flash | Microchip

The Microchip ATSAMD20G18A-AU is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20 family, featuring 256 KB of Flash, 32 KB of SRAM, and a maximum CPU clock of 48 MHz, housed in a 48-pin TQFP (7x7 mm) package with industrial-grade -40C to +85C operating range. The SAM D20G series reaches 2.14 CoreMark/MHz and integrates a 12-bit ADC, 10-bit DAC, up to 38 GPIO pins, a 256-channel Peripheral Touch Controller (PTC), and a full RTC subsystem, giving the designer an analog-rich mixed-signal platform in a compact footprint. What is a Cortex-M0+ microcontroller? A microcontroller (MCU) is a single-chip computer integrating a CPU core, program memory (Flash), working memory (SRAM), and peripherals such as ADC, timers, and communication controllers. The Cortex-M0+ is ARM's smallest, most energy-efficient application processor core, targeting cost-sensitive and battery-powered embedded designs. The ATSAMD20G18 belongs to the hierarchy: microcontroller -> ARM Cortex-M0+ MCU -> 32-bit MCU -> SAM D20 family -> low-power MCU, suitable for home automation, consumer, metering, and industrial nodes. Key features include 256 KB in-system programmable Flash (supporting Atmel/Microchip SAM-BA bootloader and SWD programming), 32 KB SRAM, a 12-bit 350 ksps ADC with up to 14 channels, a 10-bit 350 ksps DAC, six SERCOM channels configurable as USART/SPI/I2C, a 24-bit timer/counter for control applications, and a 32 kHz RTC. The device supports 1.62 V to 3.63 V single-supply operation and integrates an 8-channel Event System and a Peripheral Touch Controller for capacitive touch user interfaces. The ATSAMD20G18A-AU uses a 2-layer AHB bus matrix with separate code and data buses for deterministic interrupt latency, plus a low-power SleepWalking peripheral event fabric that wakes individual peripherals from sleep without waking the CPU, enabling < 10 uA/MHz active and deep-sleep currents below 1 uA. The 48-pin TQFP package provides easy hand-soldering and broad PCB layout compatibility for industrial designs. Typical applications include smart-home lighting controllers, low-power wireless sensor hubs, capacitive touch user interfaces for consumer appliances, industrial motor control FOC commutation blocks, battery-powered metering endpoints, and USB-to-UART bridge firmware development kits. The wide 1.62-3.63 V supply range and PTC peripheral make it a strong fit for IoT end nodes and human-machine interface panels. When designing with this part, allocate the 256 KB Flash carefully: a full Atmel/Microchip ASF or Harmony 3 stack with USB and graphics consumes 100-150 KB, leaving 100-150 KB for application code. Use the SWD header for in-circuit programming rather than relying on the bootloader pin only, and provide a 32.768 kHz crystal if RTC accuracy is required below 2 percent error.

견적 요청 문의하기