마이크로컨트롤러

제품 (18718)

ATSAMD20E16B-MU - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip
ATSAMD20E16B-MU

ATSAMD20E16B-MU - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip Technology ATSAMD20E16B-MU is an ARM Cortex-M0+ based 32-bit flash microcontroller (MCU) from the SAM D20E family, delivering up to 48 MHz CPU clock speed with 64 KB of flash memory and 8 KB of SRAM, housed in a 32-pin VQFN (5x5 mm) package with an exposed pad for improved thermal dissipation. It integrates a single-cycle hardware multiplier, single-cycle 32-bit I/O interface, and a full Cortex-M0+ debug architecture with configurable pin mapping via the SERCOM peripheral. What is an ARM Cortex-M0+ microcontroller? An ARM Cortex-M0+ MCU is an ultra-low-power 32-bit processor core from Arm designed for embedded applications that demand deterministic real-time response, low energy consumption, and a small silicon footprint. Within the broader taxonomy it sits as a microcontroller (MCU) -> 32-bit MCU -> ARM Cortex-M microcontroller -> Cortex-M0+ class. The ATSAMD20E16 belongs to Microchip's SAM D20 family, which positions it as a low-power, high-performance general-purpose MCU for consumer, industrial, and IoT edge nodes. Key features of the ATSAMD20E16B-MU include 64 KB (64K x 8) of embedded flash program memory, 8 KB of SRAM, four SERCOM (serial communication interface) instances that can each be independently configured as UART/SPI/I2C, a 12-bit ADC, two analog comparators, two brown-out detectors (BOD), power-on reset (POR), a real-time clock (RTC), watchdog timer (WDT), and six timer/counter instances. The device supports Sleep, Idle, and Standby low-power modes enabling deep sub-microamp sleep currents for battery applications. Architecturally, the ATSAMD20E16B-MU uses a single-cycle 32-bit bus matrix with separate AHB and APB bridges, giving deterministic latency on GPIO and peripheral access. The 48 MHz Cortex-M0+ core pairs with a tightly-coupled flash controller that reduces wait states on contiguous code execution, while the SERCOM blocks re-use the same silicon for I2C, SPI, or USART through a flexible pin-mux, which lets designers reassign peripherals at PCB bring-up without changing the BOM. Typical applications include home automation nodes, smart metering, industrial sensor conditioning, low-power wearables, USB human-interface devices, and consumer electronics requiring Bluetooth or sub-GHz companion chips. The wide 1.62-3.63 V VDD range lets it operate from a single Li-ion cell or two AA cells directly. When designing with this part, route the exposed pad (EP) to a continuous ground plane with thermal vias for EMI and thermal performance, and use Atmel Studio 7 or Microchip Studio with the DFP (device family pack) to configure the SERCOM peripheral multiplexing. This page synthesizes distributor pricing, drop-in alternatives within the SAM D20 family, and practical design notes not consolidated on the manufacturer product page.

견적 요청 문의하기
ATSAMD20E17A-AN - ARM Cortex-M0+ 48MHz 128KB Flash MCU | Microchip
ATSAMD20E17A-AN

ATSAMD20E17A-AN - ARM Cortex-M0+ 48MHz 128KB Flash MCU | Microchip

The Microchip Technology (formerly Atmel) ATSAMD20E17A-AN is a 32-bit ARM Cortex-M0+ flash microcontroller running up to 48 MHz, integrating 128 KB of Flash and 16 KB of SRAM in a 32-pin TQFP (7x7 mm) package. It is part of the SAM D20E family, optimized for low-power, high-performance home automation, consumer, metering, and industrial applications. According to the Microchip product page, the device supports an operating voltage range of 1.62 V to 3.63 V over -40 C to +105 C, with internal 8 MHz and 32 kHz oscillators plus PLL support. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, communication interfaces, and analog blocks. Within the broader taxonomy, the ATSAMD20E17A-AN sits at: microcontroller -> embedded processor -> semiconductor device. The ARM Cortex-M0+ core is the smallest and most energy-efficient member of the Cortex-M family, ideal for cost-sensitive and battery-powered designs. Key features include the Cortex-M0+ core with single-cycle I/O access, an 8-channel Event System for inter-peripheral signaling without CPU intervention, a 12-bit 350 ksps ADC with up to 10 analog channels, two analog comparators, and up to six SERCOM (serial communication) interfaces that can each be configured as UART, SPI, or I2C. The device also integrates a 16-bit timer/counter, a 24-bit Real-Time Counter (RTC) with calendar, and full-speed USB 2.0 device support via a separate D- pin (PA24/PA25 require external crystal for USB operation). Typical applications include smart home sensor nodes, IoT edge devices, industrial control and metering, consumer appliances, and low-power wireless companion MCUs. The wide 1.62-3.63 V supply range and dual operating temperature grades (industrial -40 to +85 C and extended -40 to +105 C) make the part suitable for both commercial and harsh-environment deployments. When designing with the ATSAMD20E17A-AN, place decoupling capacitors (100 nF + 1 uF) as close as possible to each VDD pin pair and ensure the exposed pad on the TQFP is soldered to a continuous ground pour for thermal dissipation and low-impedance return paths. The DFLL and PLL require configuration via SAMD20 firmware libraries - leaving them at reset state may limit achievable system clock precision. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATSAMD20E17A-ANT - 48MHz Cortex-M0+ MCU 128KB Flash | Microchip
ATSAMD20E17A-ANT

ATSAMD20E17A-ANT - 48MHz Cortex-M0+ MCU 128KB Flash | Microchip

The Microchip Technology ATSAMD20E17A-ANT is a 32-bit ARM Cortex-M0+ microcontroller running at up to 48 MHz with 128 KB of Flash and 16 KB of SRAM in a 32-pin TQFP (7x7) package. It operates from 1.62 V to 3.63 V and is rated for industrial temperature range from -40 C to +105 C, making it suitable for harsh-environment applications. What is a Cortex-M0+ microcontroller? The ARM Cortex-M0+ is the most energy-efficient processor in the ARM Cortex-M family, designed for embedded applications requiring low power, deterministic interrupt response, and small code footprint. MCUs in this category are widely used as the main processor in IoT nodes, sensor hubs, consumer appliances, and industrial controllers where 8-bit MCUs can no longer keep up with feature demands but full Cortex-M4 parts are over-budget. The ATSAMD20E17A integrates multiple peripherals that reduce bill-of-materials cost: a 6-channel SERCOM (configurable as UART/SPI/I2C), a 12-bit/350 ksps ADC with up to 10 analog channels, two 16-bit timer/counters, a 32.768 kHz RTC, and a full-speed USB device. The Microchip SleepWalking peripheral allows the ADC, SERCOM, and other blocks to wake the core only when a qualified event occurs, enabling system-level current consumption below 100 uA/MHz in active mode and microamp-level standby currents. Internal architecture uses a 2-channel bus matrix connecting Flash, SRAM, and peripherals to the Cortex-M0+ core via AHB and APB bridges. The Event System (12 channels) lets peripherals trigger each other without CPU intervention, further reducing average active current and enabling deterministic response times. Hardware divide and single-cycle I/O access are key architectural features inherited from the Cortex-M0+ specification. Typical applications include home automation wireless sensor nodes, low-power IoT edge devices, consumer remote controls, smart metering, industrial sensor conditioning, and USB HID peripherals such as keyboards and custom interface devices. The wide operating voltage range suits coin-cell powered designs, while the USB device makes tethered PC peripherals practical without an external PHY. When designing with this part, use the Atmel Studio 7 or MPLAB X IDE with the ASF (Atmel Software Framework) or Harmony 3, and program/debug via SWD using a Microchip debugger. Decouple VDD with at least one 100 nF ceramic capacitor per power pin pair and keep the trace between VDD and the capacitor below 5 mm. This page synthesizes distributor pricing, drop-in alternatives from the SAM D20 family and competitive Cortex-M0+ parts, and practical design notes not found in the manufacturer datasheet summary.

견적 요청 문의하기
ATSAMD20E17A-AU - 48MHz Cortex-M0+ MCU 128KB Flash | Microchip
ATSAMD20E17A-AU

ATSAMD20E17A-AU - 48MHz Cortex-M0+ MCU 128KB Flash | Microchip

The Microchip Technology ATSAMD20E17A-AU is a 32-bit ARM Cortex-M0+ microcontroller operating at up to 48 MHz, integrating 128 KB of Flash and 16 KB of SRAM in a 32-pin TQFP (7x7 mm) package. The device is part of the SAM D20E family, optimized for low-power, high-performance embedded designs. What is an ARM Cortex-M0+ microcontroller? A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (SRAM), and programmable peripherals. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor core, designed for deterministic real-time control with a Thumb-2 instruction subset. MCUs sit at the bottom of the compute hierarchy and are distinct from microprocessors by their integrated memory and peripherals. In the SAM D20E family, the Cortex-M0+ core is paired with the Microchip peripheral set, including SERCOM (configurable serial communication) and Event System for hardware-triggered DMA-like operation without CPU intervention. Key features include 128 KB Flash, 16 KB SRAM, 48 MHz maximum clock, an 8-channel 12-bit ADC, 10-bit DAC, up to six SERCOM interfaces configurable as UART/SPI/I2C, and a full-speed USB 2.0 device. The peripheral touch controller (PTC) supports capacitive touch sensing, and the Event System enables deterministic inter-peripheral signaling. Typical applications span home automation, consumer electronics, smart metering, industrial control, and IoT edge nodes where low power consumption, small footprint, and rich connectivity are required. The 32-TQFP package supports hand-solderable prototyping and standard SMT assembly lines. Design consideration: the SAM D20E requires careful clock configuration to balance CPU performance against quiescent current; sleep modes with RTC running can drop consumption to single-digit microamps. Use Atmel Studio / MPLAB X IDE with the ASF or Harmony 3 framework for driver support. This page synthesizes distributor pricing, pin-compatible SAM D20 family drop-ins, and practical design notes not collected in any single manufacturer document.

견적 요청 문의하기
ATSAMD20E17A-AUT - Cortex-M0+ MCU 48MHz 128KB | Microchip
ATSAMD20E17A-AUT

ATSAMD20E17A-AUT - Cortex-M0+ MCU 48MHz 128KB | Microchip

The Microchip ATSAMD20E17A-AUT is an ARM Cortex-M0+ based 32-bit flash microcontroller (SAM D20E family) operating at up to 48 MHz, integrating 128 KB of Flash and 16 KB of SRAM in a 32-pin TQFP (7x7 mm) package. It belongs to the low-power, high-performance SAM D20 family from Microchip (formerly Atmel) and targets home automation, consumer, metering, and industrial applications. The device pairs a deterministic Cortex-M0+ pipeline with Microchip's peripheral touch controller and SERCOM serial framework. What is a Cortex-M0+ microcontroller? A microcontroller (MCU) is a single-chip computer integrating CPU, memory (Flash for code, SRAM for data), and peripherals on one die. The Cortex-M0+ is ARM's smallest, most energy-efficient 32-bit core, optimized for deterministic interrupt response and ultra-low active current. An MCU like the ATSAMD20E17A-AUT sits in the system hierarchy as: embedded controller -> microcontroller -> 32-bit MCU -> Cortex-M0+ MCU. It differs from a microprocessor (MPU) by being self-contained without external memory buses. Key features include 128 KB Flash, 16 KB SRAM, 48 MHz core clock, an 8-channel 12-bit ADC, two Analog Comparators, up to 26 GPIO, six SERCOM modules (configurable as UART, SPI, or I2C), and the Peripheral Touch Controller supporting up to 256 buttons. The device also integrates a full-speed USB 2.0 device interface, an RTC, and SleepWalking peripherals that allow the CPU to stay asleep while peripherals autonomously service events. Architecturally the ATSAMD20E17A-AUT uses a single-cycle hardware multiply, the Microchip Event System for inter-peripheral signaling without CPU wake-up, and a 6-channel DMA engine. The 1.62V-3.63V wide supply range covers single-cell Li-ion and coin-cell operation, while built-in FPU-less Cortex-M0+ keeps the active current under 70 uA/MHz. Typical applications include smart-home sensor hubs, IoT edge nodes, BLE front-ends (paired with an ATBTLC1000 or ATSAM R34 module), HVAC controllers, industrial sensor transmitters, USB HID peripherals, and low-cost brushed DC motor control via a companion ATA6826 driver. The wide voltage range and low sleep current also suit battery-powered metering. When designing with this MCU, allocate the SERCOM channels early in the firmware architecture because each channel can only be bound to one of UART/SPI/I2C at a time. The 32-pin TQFP variant limits GPIO to 26 pins compared to the 48-pin variant, so plan pin counts accordingly. This page synthesizes Microchip datasheet data, distributor pricing tiers, and practical design notes not available on the OEM summary, giving engineers a single reference for vendor selection and PCB bring-up of the ATSAMD20E17A-AUT.

견적 요청 문의하기
ATSAMD20E17A-MN - 128KB Flash ARM Cortex-M0+ MCU | Microchip
ATSAMD20E17A-MN

ATSAMD20E17A-MN - 128KB Flash ARM Cortex-M0+ MCU | Microchip

The Microchip ATSAMD20E17A-MN is a 32-bit ARM Cortex-M0+ based flash microcontroller with 128KB of Flash and 16KB of SRAM, operating at up to 48MHz from a 1.62V to 3.6V supply in a 32-pin VQFN (5x5 mm) package. It is part of the SAM D20E family designed for low-power, high-performance embedded applications. A microcontroller (MCU) is an integrated circuit that combines a processor core, program memory (Flash), working memory (SRAM), and a rich set of peripherals on a single die. The Cortex-M0+ is the most energy-efficient ARM processor core, offering Thumb-2 instruction set compatibility and a 2.14 CoreMark/MHz performance figure. Within the broader taxonomy, this device is a Flash microcontroller -> embedded MCU -> 32-bit microcontroller -> semiconductor. Compared to 8-bit MCUs like the PIC16F series, the Cortex-M0+ offers higher computational throughput, deterministic interrupts via the Nested Vectored Interrupt Controller (NVIC), and modern peripherals such as SERCOM configurable serial interfaces. Key features of the ATSAMD20E17A-MN include six SERCOM interfaces (each configurable as UART, SPI, or I2C), a 12-bit 1 MSPS ADC with up to 10 analog channels, two 16-bit Timer/Counters (TC), a 32-bit Real-Time Counter (RTC) with calendar mode, a full-speed USB 2.0 device interface, and an Event System for inter-peripheral signaling without CPU intervention. The device supports up to 26 programmable I/O pins. The SAM D20 architecture uses a single-cycle hardware multiplier and a 2-layer AHB-Lite bus matrix, giving 2.14 CoreMark/MHz. The Peripheral Touch Controller (PTC) supports capacitive touch buttons, sliders, and wheels. A low-power SleepWalking peripheral can wake the CPU only when meaningful data is present, enabling battery-friendly idle states as low as a few microamperes in deep-sleep modes. Typical applications include home automation nodes, smart metering endpoints, consumer electronics, low-cost sensor hubs, and industrial control peripherals. The wide 1.62-3.6V operating range and 105C extended-industrial temperature option also suit rugged environments. When designing with this device, pay attention to decoupling (place 100nF and 1uF capacitors within a few millimeters of each VDD pin) and consider whether the 5x5 mm QFN land pattern is acceptable for your manufacturing process. The PTC touch channels overlap with the ADC, so verify pin allocation before locking the BOM. This page synthesizes distributor pricing, drop-in alternates within the SAM D20 family, and practical design notes that are not aggregated on the manufacturer datasheet alone, helping engineers accelerate their selection.

견적 요청 문의하기
ATSAMD20E18A-ANT - ARM Cortex-M0+ MCU 48MHz 256KB TQFP-32
ATSAMD20E18A-ANT

ATSAMD20E18A-ANT - ARM Cortex-M0+ MCU 48MHz 256KB TQFP-32

The Microchip Technology ATSAMD20E18A-ANT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20E family, delivering 48 MHz CPU performance with 256 KB Flash and 32 KB SRAM in a 32-pin TQFP (7x7 mm) package. It operates from 1.6 V to 3.6 V and is qualified to 105 degrees C, making it well suited to industrial and consumer environments. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, communication interfaces, and analog-to-digital converters. The Cortex-M0+ core is the smallest and most energy-efficient member of the ARM Cortex-M family, optimized for deterministic, low-power embedded workloads. As part of the broader hierarchy MCU -> embedded controller -> system-on-chip -> semiconductor, the ATSAMD20E18A-ANT sits at the entry-level Cortex-M tier but still offers substantial compute density for sensor hubs, human-machine interfaces, and protocol bridges. Key differentiating specifications include the Cortex-M0+ core at 48 MHz with single-cycle GPIO access, 256 KB self-programmable Flash, 32 KB SRAM, a 12-bit 350 ksps ADC with up to 16 analog channels, a 10-bit DAC, a 32-bit RTC, and a 256-channel Peripheral Touch Controller (PTC) that supports capacitive touch buttons, sliders, and proximity sensors without external components. The integrated SERCOM module provides up to six configurable serial interfaces that can each operate as I2C, SPI, or USART, dramatically simplifying BOM optimization. Architecturally, the device uses the Cortex-M0+ v6-M instruction set with hardware multiply and divide, NVIC with 4 priority levels, and a low-power SleepWalking peripheral event system that wakes only the peripherals needed for a task while keeping the core asleep. This combination, together with typical active current of approximately 70 uA/MHz, places the part in Microchip's low-power performance tier. Typical applications include home automation control nodes, smart metering, capacitive touch user interfaces, wireless sensor transceivers paired with modules such as ATSAMR21, industrial sensor hubs, and consumer appliances. The wide 1.6-3.6 V supply range simplifies single-Li-ion or 3.3 V system design. When designing with this part, allocate sufficient decoupling near each VDD pin and follow the 32-pin TQFP land pattern recommendations in the datasheet to maintain ADC accuracy. This page synthesizes verified distributor pricing, drop-in alternatives, application notes, and PCB design considerations not found in the manufacturer datasheet alone.

견적 요청 문의하기
ATSAMD20E18A-AU - ARM Cortex-M0+ MCU 256KB Flash 32-TQFP | Microchip
ATSAMD20E18A-AU

ATSAMD20E18A-AU - ARM Cortex-M0+ MCU 256KB Flash 32-TQFP | Microchip

The Microchip Technology ATSAMD20E18A-AU is a 32-bit ARM Cortex-M0+ based flash microcontroller from the SAM D20E family, delivering 48 MHz core performance with 256 KB Flash and 32 KB SRAM in a 32-pin TQFP (7x7 mm) package. The device operates from a 1.62 V to 3.63 V supply and includes up to 26 programmable I/O pins, a 12-channel SERCOM (serial communication) subsystem, a 12-bit 350 ksps ADC, and a 10-bit 350 ksps DAC. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash for program code and SRAM for data), and a rich set of peripherals on one die. The Cortex-M0+ sits at the lowest-power end of the ARM Cortex-M family tree, optimized for deterministic interrupt response at minimal energy cost. MCUs belong to the broader embedded controller hierarchy - faster than 8/16-bit legacy microcontrollers but simpler than microprocessors, and form a subset of integrated circuits used in virtually all digital products. Key features of the ATSAMD20E18A-AU include the Microchip proprietary Atmel START / MPLAB X IDE support, a 32 KB SRAM with a tightly-coupled bus for low-latency access, a full-speed USB 2.0 device with on-chip transceiver, and a peripheral touch controller (PTC) supporting capacitive buttons, sliders, and wheels. The integrated sleepwalking peripheral event system allows peripherals to wake the core only when needed, enabling deep Sleep mode currents below 10 µA. The architecture uses a single 32-bit AHB-Lite bus with a separate bridge for low-power peripherals, and the Cortex-M0+ implements the ARMv6-M Thumb instruction set. A hardware multiplier (32-bit result in one cycle) and configurable NVIC (Nested Vectored Interrupt Controller) with up to 32 IRQs give the part real-time responsiveness uncommon in entry-level MCUs. Typical applications include home automation nodes, low-cost consumer devices, smart energy metering, industrial sensor hubs, and capacitive-touch user interfaces. The wide 1.62 V to 3.63 V range supports direct connection to single-cell Li-ion (3.7 V nominal) and 3.3 V regulated rails without level shifters. When designing with this part, decouple VDDIN and VDDCORE with 100 nF plus 4.7 µF bulk capacitors placed within 5 mm of the pins. Use the SERCOM peripheral (not legacy USART/SPI/I2C) and route D+ / D- differential traces with 90 Ω impedance if USB is enabled. This page synthesizes distributor pricing from DigiKey, Mouser, Heisener, LCSC, and Octopart; same-package drop-in alternatives from the Microchip SAMD20 family; and practical design notes not consolidated in the manufacturer datasheet.

견적 요청 문의하기
ATSAMD20E18A-AUT - 48MHz Cortex-M0+ 256KB Flash MCU | Microchip
ATSAMD20E18A-AUT

ATSAMD20E18A-AUT - 48MHz Cortex-M0+ 256KB Flash MCU | Microchip

The Microchip Technology ATSAMD20E18A-AUT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20E family, featuring 256KB of flash memory, 32KB of SRAM, and a 48 MHz core clock in a 32-pin TQFP (7x7 mm) package. It integrates a 12-bit ADC, a 10-bit DAC, a 256-channel Peripheral Touch Controller (PTC), a full-featured RTC, and multiple SERCOM modules for flexible serial communication. A Cortex-M0+ microcontroller (MCU) is a low-power 32-bit processor core from the ARM Cortex-M family, designed for energy-efficient embedded applications. It sits in the hierarchy: ARM Cortex-M0+ -> Cortex-M series -> 32-bit RISC microcontroller -> embedded processor -> semiconductor. Cortex-M0+ cores target cost-sensitive IoT, sensor, and consumer devices that need 32-bit performance at 8-bit price points, with deterministic interrupt handling and a thumb-only instruction set for compact code density. Key features of the ATSAMD20E18A-AUT include a 1.6V to 3.6V supply range, 6 SERCOM channels that can each operate as USART, I2C, or SPI, a 12-channel 12-bit ADC with 350 ksps sampling, a 10-bit 350 ksps DAC, and full USB 2.0 Full-Speed device support with on-chip transceiver. The device also offers 6 event channels for inter-peripheral signalling without CPU intervention, an idle/standby power-down mode that drops current to a few microamps, and a built-in 32 kHz RTC oscillator with calendar mode. Architecturally, the part uses an M0+ core with a single-cycle hardware multiplier and a Nested Vectored Interrupt Controller (NVIC). The flash controller supports in-application programming, and the device is supported by Atmel/Microchip Studio, MPLAB X IDE, and the Harmony framework, easing firmware porting. The 32-pin TQFP (AUT - tape-and-reel packaging, 'U' indicating industrial temperature grade) offers easy hand-solder-friendly prototyping. Typical applications include home automation nodes, smart sensor hubs, low-power wireless MCU companions, industrial metering and control, consumer electronics human-interface devices, and battery-powered IoT endpoints. The integrated PTC enables robust touch-button, slider, and wheel interfaces without external touch ICs, making the part especially attractive for appliance front panels. When designing with this part, choose a 32.768 kHz crystal for RTC accuracy and add a 1uF + 0.1uF decoupling pair close to each VDD pin. For USB applications, route the D+/D- lines as a 90-ohm differential pair and tie VBUS to the USB VBUS pad through a voltage divider. The -AUT suffix denotes tape-and-reel packaging and industrial (-40C to +85C) temperature grade. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes - all derived from the Microchip datasheet family and verified web sources - that go beyond the bare datasheet content to support faster engineering decisions.

견적 요청 문의하기
ATSAMD20E18A-MNT - 256KB Flash ARM Cortex-M0+ MCU | Microchip
ATSAMD20E18A-MNT

ATSAMD20E18A-MNT - 256KB Flash ARM Cortex-M0+ MCU | Microchip

The Microchip Technology ATSAMD20E18A-MNT is a 32-bit ARM Cortex-M0+ flash microcontroller delivering up to 48 MHz CPU performance in a 32-pin VQFN (MNT) package with exposed pad. It integrates 256 KB of Flash program memory and 32 KB of SRAM, providing generous headroom for embedded firmware, protocol stacks, and sensor-fusion code in space-constrained designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a rich set of peripherals. The ARM Cortex-M0+ is the smallest and most energy-efficient ARM core, optimized for low-power deterministic interrupt response, while the SAM D20E series adds Microchip-specific peripherals, power management, and an event system. Within the broader taxonomy, the ATSAMD20 sits between 8-bit AVR/PIC MCUs and higher-performance Cortex-M3/M4 parts, making it the canonical choice for cost-sensitive, battery-powered, sensor-centric products. Key features of the ATSAMD20E18A-MNT include 6 SERCOM (serial communication) interfaces configurable as I2C/SPI/UART, a 12-bit 350 ksps ADC with up to 20 channels, a 10-bit DAC, a 256-channel Peripheral Touch Controller (PTC) for capacitive buttons and sliders, and a full-speed USB 2.0 device port. The integrated event system allows peripherals to trigger one another without CPU intervention, freeing the Cortex-M0+ core for application logic and reducing active current. Technically, the device operates from 1.62 V to 3.63 V, supports Sleep, Idle, Standby, and Backup sleep modes with sub-microamp standby current, and includes a 32.768 kHz RTC with calendar. The Cortex-M0+ core reaches 2.14 CoreMark/MHz, and the Memory Protection Unit (MPU) helps harden RTOS-based firmware against runaway pointers. Programming is via the integrated Serial Wire Debug (SWD) interface and the Microchip Atmel Studio / MPLAB X toolchain. Typical applications include home automation nodes (HVAC, lighting, smart plugs), industrial sensor transmitters, consumer wearables and fitness bands, low-power wireless sensor nodes (when paired with an AT86RF233 or similar 2.4 GHz radio), capacitive-touch user interfaces, and USB peripherals such as HID controllers. The wide operating voltage and rich analog peripherals make it ideal for battery-powered measurement products. When designing with this part, choose decoupling capacitors per the datasheet (typically one 100 nF per VDD pin) and route SWD signals on inner layers with a ground return path. For best EMC performance, the exposed pad must be soldered to a contiguous ground plane, and unused I/O pins should be configured as outputs low rather than left floating. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and design notes not found on the manufacturer datasheet alone, helping engineers shorten the BOM-evaluation cycle for ATSAMD20-based designs.

견적 요청 문의하기
ATSAMD20E18A-MU - 48MHz ARM Cortex-M0+ 256KB Flash MCU | Microchip
ATSAMD20E18A-MU

ATSAMD20E18A-MU - 48MHz ARM Cortex-M0+ 256KB Flash MCU | Microchip

The Microchip Technology ATSAMD20E18A-MU is a 32-bit ARM Cortex-M0+ microcontroller in the SAM D20E family, featuring 256KB Flash, 32KB SRAM, and a 48MHz CPU, housed in a 32-pin VQFN (5x5 mm) package with an exposed pad. It is built around the Cortex-M0+ core, executes the Thumb-2 instruction set, and integrates a single-cycle hardware multiplier. The device supports 1.62V to 3.63V supply operation and reaches 2.14 CoreMark/MHz, making it suitable for a wide range of performance- and power-sensitive embedded applications. An ARM Cortex-M0+ microcontroller is an entry-level 32-bit MCU that delivers higher code density and energy efficiency than legacy 8-bit/16-bit microcontrollers while retaining a familiar programmer model. Within the product taxonomy, the Cortex-M0+ sits between Cortex-M0 and Cortex-M3 in the ARM Cortex-M family; the SAM D20E specifically belongs to Microchip's SAM D20 series, which is positioned for low-power, general-purpose 32-bit designs spanning home automation, consumer, metering, and industrial control applications. The integration of 256KB Flash and 32KB SRAM in a 5x5 mm VQFN makes the family attractive where code size and PCB area are tight. Key features include 256KB Flash (256K x 8), 32KB SRAM, up to 48MHz CPU clock, an integrated peripheral touch controller (PTC) supporting sliders, buttons, and proximity sensing, and the standard SAM D20 SERCOM module count for I2C, SPI, and UART operation. The part also provides a 12-bit ADC, 10-bit DAC, multiple timers (TC, TCC), and a full-speed USB 2.0 device interface. Typical I/O count for the 32-pin variant supports up to 26 GPIO lines. Architecturally, the device uses a single-cycle hardware multiplier and a tightly coupled memory controller to deliver efficient Cortex-M0+ execution at up to 2.14 CoreMark/MHz. The integrated SleepWalking peripheral event system allows selected peripherals to wake the core only when needed, which contributes to the SAM D20 series' reputation for low standby current and Idle/Standby modes consuming microamp-level current. Typical applications include smart-home sensor hubs, low-power industrial controllers, USB-to-UART bridges, battery-powered metering devices, and human-machine interface (HMI) controllers using touch or segment-LCD fronts. The combination of 256KB Flash and the extended SAM D20 peripheral set is well matched to connected appliances and IoT edge nodes that must run a small RTOS or bare-metal state machine. When designing with this part, confirm that your firmware stack (startup, linker script, and ASF/MPLAB Harmony configuration) targets the SAM D20E variant and the 256KB Flash size. Pay attention to decoupling of the exposed thermal pad for thermal performance, and review the recommended load capacitance on the 32kHz crystal if RTC accuracy is critical. This page synthesizes verified distributor pricing, drop-in pin-compatible alternatives from the SAMD20 family, and practical design notes not found on a single manufacturer page - giving procurement, FAE, and design engineers one place to evaluate and substitute ATSAMD20E18A-MU.

견적 요청 문의하기
ATSAMD20G14A-AN - 48MHz Cortex-M0+ 16KB Flash MCU | Microchip
ATSAMD20G14A-AN

ATSAMD20G14A-AN - 48MHz Cortex-M0+ 16KB Flash MCU | Microchip

The Microchip (Atmel) ATSAMD20G14A-AN is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20 family, featuring 16KB of Flash and 2KB of SRAM, operating at up to 48MHz with 2.14 CoreMark/MHz performance. It is housed in a 48-pin TQFP (7x7mm) industrial-grade package and supports 1.6V to 3.6V operation. What is a Cortex-M0+ microcontroller? An ARM Cortex-M0+ microcontroller (MCU) is a low-power 32-bit processor core designed for embedded applications requiring deterministic real-time response and minimal energy consumption. MCUs integrate CPU, Flash, SRAM, and peripherals (ADC, timers, communication interfaces) onto a single die, sitting below microprocessors in the system hierarchy: CPU -> MCU -> SoC -> semiconductor. The Cortex-M0+ is the smallest, most energy-efficient ARM core, targeting battery-powered IoT, sensor hubs, and consumer devices where 8/16-bit MCUs previously dominated. Key features of the ATSAMD20G14A-AN include the SERCOM (Serial Communication Interface) peripheral that can be configured as UART, SPI, or I2C, a 12-bit ADC with up to 14 channels, multiple 16/32-bit timers, and the Event System for hardware-triggered inter-peripheral signalling without CPU overhead. The device includes a full-speed USB 2.0 Device interface on select family members and operates from a single 1.6V to 3.6V supply with on-chip voltage regulation. The SAM D20 architecture pairs the Cortex-M0+ core with a single-cycle hardware multiplier, single-cycle I/O port access, and Microchip's SleepWalking peripherals that wake the CPU only when meaningful events occur. The 48MHz clock source can be derived from the internal 8MHz oscillator or an external crystal, providing flexibility for cost-sensitive or precision-timing applications. Typical applications include home automation controllers, industrial sensor nodes, low-power wireless sensor hubs, consumer appliances, smart metering, and battery-powered IoT edge devices. Its low active current and deep-sleep modes make it well-suited for energy-harvesting designs. When designing with this MCU, ensure the supply decoupling network follows the 100nF+bulk capacitor recommendation and that unused pins are configured as outputs or inputs with internal pull-up enabled to minimize power leakage in sleep modes. This page synthesizes live distributor pricing, drop-in SAM D20 family alternatives, and practical design notes not consolidated on the manufacturer datasheet page.

견적 요청 문의하기
ATSAMD20G14A-AUT - 48MHz Cortex-M0+ MCU 16KB Flash TQFP-48 | Microchip
ATSAMD20G14A-AUT

ATSAMD20G14A-AUT - 48MHz Cortex-M0+ MCU 16KB Flash TQFP-48 | Microchip

The Microchip Technology ATSAMD20G14A-AUT is a low-power, high-performance ARM Cortex-M0+ based flash microcontroller (MCU) from the SAM D20G family, operating at up to 48 MHz with 16 KB of Flash and 2 KB of SRAM, housed in a 48-pin TQFP (7x7 mm) package. It targets a wide range of home automation, consumer, metering, and industrial applications requiring deterministic 32-bit processing in a compact footprint. What is an ARM Cortex-M0+ microcontroller? It is a 32-bit RISC processor core designed by ARM as the most energy-efficient member of the Cortex-M family, intended for deeply embedded applications. Microcontrollers integrating Cortex-M0+ cores (Cortex-M0+ MCU -> ARM microcontroller -> 32-bit MCU -> embedded controller) bridge sensor/actuator signals to firmware-driven decision logic in IoT endpoints, motor nodes, and portable instruments. Key features of the ATSAMD20G14A-AUT include 16 KB Flash, 2 KB SRAM, an integrated Serial Communication Interface (SERCOM) block configurable as UART/SPI/I2C, a 12-bit ADC, a 10-bit DAC, multiple timers, and the full Microchip SAM D20 peripheral set. The device operates from 1.62 V to 3.63 V, supports industrial temperature grade (-40C to +85C), and includes the SleepWalking peripheral event system that lets peripherals wake the CPU autonomously to minimize average power consumption. Architecturally, the ATSAMD20G14A-AUT combines a single-cycle Cortex-M0+ core with a 6-channel DMA controller, an event system for inter-peripheral signaling, and Microchip's Atmel Studio/MPLAB X toolchain compatibility. Code execution is deterministic, interrupt latency is short, and the integrated voltage regulator supports single-supply Li-ion or 3.3 V designs without external regulation. Typical applications include smart-home sensor hubs, low-power wireless nodes (when paired with an external transceiver), industrial metering, HVAC controllers, consumer white goods, and human-machine interface (HMI) touch panels. The combination of small Flash footprint, low-power modes, and rich peripherals also suits wearable fitness devices and battery-powered instrumentation. When designing with this part, place a 100 nF decoupling capacitor on each VDD pin and keep the trace to VDDCORE short; use the SERCOM peripheral's pin-mux flexibility to optimize PCB routing. Program/debug requires an SWD header compatible with the Atmel-ICE, MPLAB ICD 4, or a CMSIS-DAP adapter. This page synthesizes distributor pricing, drop-in alternatives within the SAM D20 family, and practical design notes that go beyond the manufacturer datasheet to support rapid BOM decisions.

견적 요청 문의하기
ATSAMD20G14A-MN - ARM Cortex-M0+ MCU, 48MHz, 16KB Flash | Microchip
ATSAMD20G14A-MN

ATSAMD20G14A-MN - ARM Cortex-M0+ MCU, 48MHz, 16KB Flash | Microchip

The Microchip Technology ATSAMD20G14A-MN is a 32-bit ARM Cortex-M0+ microcontroller (MCU) from the SAM D20G family, featuring 16KB of Flash, 2KB of SRAM, and a maximum CPU frequency of 48MHz, housed in a 48-pin VQFN (7x7 mm) package. It operates from a wide 1.62V to 3.63V supply, integrates a 14-channel 12-bit ADC and a 10-bit DAC, and supports I2C, SPI, UART/USART, and I2S serial interfaces. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable peripherals. Within the broader taxonomy, the ATSAMD20G14A-MN is an instance of: 32-bit microcontroller -> ARM Cortex-M0+ MCU -> SAM D20 family -> Atmel/Microchip SMART ARM-based MCU. As a Cortex-M0+ device it delivers Thumb-2 instruction efficiency at 2.46 CoreMark/MHz, the highest per-MHz performance of any ARM Cortex-M core, while consuming as little as 70 uA/MHz active and sub-1 uA in deep-sleep standby modes. Key features include the Cortex-M0+ core with single-cycle I/O access, 6 SERCOM (serial communication) interfaces each reconfigurable between I2C/SPI/UART, a 12-bit 350 ksps ADC with up to 14 analog channels, a 10-bit 350 ksps DAC, and an 8-channel Event System for inter-peripheral signaling without CPU involvement. The device also integrates an 8-bit timer/counter, a 16-bit timer/counter with capture/PWM modes, a 32-bit Real-Time Counter, and a full-speed USB 2.0 device interface on selected variants. The SAM D20G uses an efficient pipeline architecture with deterministic interrupt latency, single-cycle GPIO access, and a Peripheral Event System that allows direct peripheral-to-peripheral triggers without waking the CPU. Its low-power design uses multiple SleepWalking-aware peripherals, an on-chip 32 kHz oscillator with PLL multiplier to 48 MHz, and a brown-out detector with separate thresholds for Flash and I/O rails. Typical applications include home automation nodes, consumer electronics HMI, smart metering, industrial sensor hubs, IoT edge nodes, and wearable devices. The wide operating voltage (1.62-3.63V) and low SleepWalking current also make it suitable for battery-powered designs powered from a single Li-ion or 2xAA cell. When designing with this device, use the Atmel/Microchip ASF (Atmel Software Framework) or the modern MPLAB Harmony v3 peripheral library, select the internal 48 MHz DFLL for the system clock with a 32.768 kHz crystal reference, and follow the datasheet recommended decoupling of one 100 nF capacitor per VDD pin plus a bulk capacitor near the regulator output. This page synthesizes distributor pricing, drop-in alternatives within the SAM D20 family, and practical design notes not aggregated on the manufacturer datasheet page, helping engineers select, source, and qualify the part faster.

견적 요청 문의하기
ATSAMD20G14A-MNT - ARM Cortex-M0+ MCU, 48MHz, 16KB Flash | Microchip
ATSAMD20G14A-MNT

ATSAMD20G14A-MNT - ARM Cortex-M0+ MCU, 48MHz, 16KB Flash | Microchip

The Microchip ATSAMD20G14A-MNT is a low-power, high-performance 32-bit ARM Cortex-M0+ flash microcontroller (MCU) in the Atmel | SMART SAM D20G family, integrating 16 KB of flash and 2 KB of SRAM, running at up to 48 MHz, and housed in a 48-pin VQFN (7x7 mm) package with an exposed thermal pad for improved dissipation. It operates across a wide 1.62V to 3.63V supply range and delivers 2.14 CoreMark/MHz, balancing deterministic real-time performance with the low energy modes required for battery-driven designs. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program and data memory, and a rich set of on-chip peripherals such as timers, ADC, communication interfaces, and general-purpose I/O. The ARM Cortex-M0+ belongs to the Cortex-M family of 32-bit RISC cores designed for embedded systems, while Microchip's SAM D20 product line extends this core with low-power SleepWalking peripherals, a SERCOM (Serial Communication Interface) block, and event system that make the device competitive against 8-bit and 16-bit MCUs while remaining easy to program. Within the broader taxonomy, this part sits at: MCU -> microcontroller -> ARM Cortex-M0+ microcontroller -> SAM D20 family -> low-power Cortex-M0+ MCU. Key features of the ATSAMD20G14A-MNT include up to 38 GPIO pins, six SERCOM channels configurable as UART/SPI/I2C, a 12-bit 350 ksps ADC with up to 14 channels, 16-bit timers/counters, a 32 kHz RTC, full-speed USB 2.0 device support in related variants, and the standard SAM D20 peripheral mix. The 'MNT' suffix indicates the industrial temperature grade (-40C to +105C), VQFN-48 (7x7) package, and Tape & Reel packaging, with Pb-free / RoHS-compliant lead finish. Typical applications include home automation, consumer electronics, smart metering, industrial sensor nodes, human-machine interface (HMI) controllers, and IoT edge devices. Compared with 8-bit PIC or AVR alternatives at similar cost points, the SAM D20G delivers roughly an order-of-magnitude more compute, modern peripherals, and an ARM ecosystem (CMSIS, ASF, Harmony, GCC/IAR/Keil toolchains). At the same time it preserves strong low-power behaviour - down to a few microamperes in deep-sleep modes with RAM retention - making it a credible drop-in upgrade when firmware complexity outgrows 8-bit MCUs. When designing with the ATSAMD20G14A-MNT, ensure the 48-pin VQFN exposed pad is soldered to a continuous ground plane for both thermal and electrical performance, place the two 100 nF + 1 uF VDD decoupling pairs within 2 mm of each VDD pin, and follow Microchip's SAM D20 reference design notes for the 32.768 kHz crystal layout if RTC accuracy is required.

견적 요청 문의하기
ATSAMD20G14A-MUT - 32-bit ARM Cortex-M0+ MCU, 48MHz, 16KB Flash | Microchip
ATSAMD20G14A-MUT

ATSAMD20G14A-MUT - 32-bit ARM Cortex-M0+ MCU, 48MHz, 16KB Flash | Microchip

The Microchip Technology (formerly Atmel) ATSAMD20G14A-MUT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20G family, operating at up to 48 MHz with 16 KB of Flash and 2 KB of SRAM, housed in a 48-pin QFN (7x7 mm) package. It integrates a 2.14 CoreMark/MHz CPU, a 12-bit ADC, multiple SERCOM interfaces, and an event system in a low-power architecture. The -MUT suffix indicates tape-and-reel packaging at 2,500-piece reels and a QFN-48 (7x7) footprint with exposed thermal pad. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), working memory (SRAM), and programmable peripherals. The Cortex-M0+ core sits at the lowest end of the ARM Cortex-M family, optimized for minimal gate count, deterministic interrupt latency, and ultra-low active power. The SAM D20 family is positioned as a low-power, high-performance replacement for 8-bit and 16-bit MCUs in home automation, consumer, metering, and industrial applications. Within the SAM D20 family, the -G14 variant represents the 48-pin 16 KB Flash tier. Key features of the ATSAMD20G14A-MUT include a 48 MHz maximum CPU clock, single-cycle 32-bit multiply, 14-channel 12-bit ADC with 350 kSamples/s throughput, up to six SERCOM (serial communication) interfaces configurable as UART, SPI, or I2C, a full-speed USB 2.0 device controller, a 24-bit timer/counter, RTC, and brown-out detection. The peripheral event system allows direct hardware-level signaling between peripherals without CPU intervention, which reduces latency and current draw. Typical applications include smart-home sensor nodes, low-power wireless IoT endpoints, industrial control and metering front-ends, USB-CDC human-interface devices, and battery-powered wearables. The integrated USB 2.0 full-speed controller makes the ATSAMD20G14A-MUT a strong fit for low-cost USB devices, while the Cortex-M0+ core delivers more than 60 DMIPS of processing while consuming only a few milliamps active. When designing with this MCU, verify that your firmware uses an Atmel/Microchip DFP device pack and a compatible toolchain (e.g., MPLAB X IDE with the XC32 compiler or Atmel Studio with GCC). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATSAMD20G14B-AU - 48MHz Cortex-M0+ MCU 16KB Flash | Microchip
ATSAMD20G14B-AU

ATSAMD20G14B-AU - 48MHz Cortex-M0+ MCU 16KB Flash | Microchip

The Microchip Technology ATSAMD20G14B-AU is a low-power, high-performance 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20 family, operating at up to 48 MHz and housed in a 48-pin TQFP (7x7 mm) industrial-temperature package. It integrates 16 KB of flash program memory and 2 KB of SRAM on-die, with the Cortex-M0+ core delivering 0.97 DMIPS/MHz while drawing as little as 50 uA/MHz active, making it well-suited to energy-constrained embedded designs. A microcontroller (MCU) is a single-chip computer that combines a CPU core, volatile and non-volatile memory, and a rich set of programmable peripherals on one silicon die. The Cortex-M0+ architecture sits at the low end of the ARMv6-M family, prioritizing deterministic interrupt response, minimal gate count, and ultra-low active/sleep current; in a system hierarchy it falls under 32-bit microcontrollers -> microcontrollers -> embedded ICs -> integrated circuits. The SAM D20 line in particular targets low-power IoT, consumer, and industrial nodes that previously required 8/16-bit parts but benefit from Thumb-2 code density and modern toolchains. Key features of the ATSAMD20G14B-AU include an integrated SERCOM peripheral block (configurable as UART, SPI, or I2C), a 12-channel 12-bit 350 ksps ADC, two analog comparators, a 16-bit timer/counter, RTC, and full-speed USB device support on selected die revisions. The device operates across 1.62 V to 3.63 V and the -AU suffix indicates a -40 C to +85 C industrial temperature grade, suitable for unattended outdoor, factory, and metering enclosures. Architecturally, the ATSAMD20G14B-AU uses Microchip's proprietary low-power process and the SAM D20 platform fabric, including a separate low-power backup domain and the SleepWalking peripheral-to-peripheral DMA path that lets the core stay asleep while peripherals wake it on stimulus. This design is the reason the part can hit sub-1 uA sleep currents with full RAM retention, a key reason battery-powered sensor and metering designs default to SAM D20. Typical applications include home-automation sensor nodes, smart-metering endpoints, low-end consumer appliances, human-interface boards (keypad + LED), HVAC control, and portable industrial test accessories. The combination of USB device, ADC, and SERCOM gives designers a flexible IO count without external glue logic. Design tip: the SAM D20 family uses the Atmel/Microchip DFLL or a 32.768 kHz crystal to derive the 48 MHz CPU clock; for USB applications the 48 MHz must be sourced from a 12 MHz crystal multiplied by the PLL. Plan decoupling with one 100 nF X7R per VDD pin and a bulk 4.7 uF on the analog rail to keep ADC noise low. This page synthesizes distributor pricing, drop-in alternatives across the SAM D20 family, and practical design notes that go beyond what the manufacturer datasheet alone offers.

견적 요청 문의하기
ATSAMD20G14B-AUT - 48MHz Cortex-M0+ 16KB Flash MCU | Microchip
ATSAMD20G14B-AUT

ATSAMD20G14B-AUT - 48MHz Cortex-M0+ 16KB Flash MCU | Microchip

Microchip Technology ATSAMD20G14B-AUT is an ARM Cortex-M0+ based 32-bit microcontroller from the SAM D20G family, delivering 48 MHz CPU performance with 16 KB of Flash and 2 KB of SRAM in a 48-pin TQFP (7x7 mm) package. The part is rated for industrial temperature range (-40C to +85C) and targets cost-sensitive, low-power embedded applications across home automation, consumer, metering, and industrial segments. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash for code, SRAM for data), and programmable peripherals into one package. The ARM Cortex-M0+ is the most energy-efficient core in the ARM-M family, designed for deterministic real-time embedded control with the smallest silicon area and lowest active power per MHz. The SAM D20 series positions Cortex-M0+ above 8-bit/16-bit legacy architectures by offering 32-bit performance, modern peripherals, and industry-standard toolchains while preserving ultra-low-power behaviour. Key features of the ATSAMD20G14B-AUT include up to 14 SERCOM (serial communication) interfaces that can be mapped to UART, SPI, I2C, or LIN, a 12-bit ADC with up to 14 channels, a 10-bit DAC, a 256-channel Peripheral Touch Controller (PTC), a Real-Time Clock (RTC) with calendar mode, and the standard Microchip SleepWalking peripheral-event system. The device operates from a 1.62V to 3.63V supply, supporting both 1.5V and 3.3V system rails. The 48-pin TQFP footprint is pin-compatible with the larger-memory siblings ATSAMD20G15B-AUT (32 KB Flash) and ATSAMD20G16B-AUT (64 KB Flash), enabling in-family scaling without PCB rework. The ATSAMD20G14B-AUT is well suited to sensor nodes, capacitive-touch user interfaces, smart meters, white goods, HVAC controllers, and low-power wireless companion MCUs. The industrial temperature grade and the rich peripheral mix allow a single part to drive a touch panel, communicate with a sensor or radio, and run the application loop while drawing minimal idle current. Designers should plan for an external 32.768 kHz crystal if RTC accuracy is required, and ensure decoupling follows the datasheet reference layout. The free Atmel Studio / MPLAB X toolchain, ASF / Harmony drivers, and SEGGER J-Link support shorten firmware development cycles. This page consolidates distributor pricing, drop-in alternatives, and design notes that go beyond what the manufacturer datasheet alone provides.

견적 요청 문의하기
ATSAMD20G14B-MU - 48MHz ARM Cortex-M0+ MCU 16KB Flash | Microchip
ATSAMD20G14B-MU

ATSAMD20G14B-MU - 48MHz ARM Cortex-M0+ MCU 16KB Flash | Microchip

The Microchip Technology ATSAMD20G14B-MU is a low-power, high-performance ARM Cortex-M0+ based flash microcontroller (MCU) running up to 48 MHz, integrating 16 KB of flash and 2 KB of SRAM in a 48-pin VQFN (7x7 mm) package with exposed thermal pad. It supports an operating voltage range of 1.62 V to 3.63 V, six flexible SERCOM communication interfaces, a 12-bit ADC, 10-bit DAC, and multiple timers, making it suitable for a wide range of home automation, consumer, metering, and industrial applications. An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core implementing the Thumb/Thumb-2 instruction set, optimized for energy-efficient embedded designs. The Cortex-M0+ sits within a broader hierarchy of MCU cores (Cortex-M0 -> Cortex-M0+ -> Cortex-M3 -> Cortex-M4 -> Cortex-M7), and the SAMD20 family belongs to the larger Atmel/Microchip SAM D family of microcontrollers, which in turn is part of the embedded MCU segment of the semiconductor industry. Key features include the Cortex-M0+ core with single-cycle hardware multiply, the SERCOM module that can be configured as UART/USART, SPI, or I2C, an 8-channel 12-bit ADC with up to 350 ksps conversion rate, a 10-bit 350 ksps DAC, and a full-speed USB 2.0 device with on-chip transceiver. The device also includes a 32 kHz RTC, multiple PWM-capable timers (TC), and an Event System for inter-peripheral signaling without CPU intervention. The ATSAMD20G14B-MU uses an embedded Flash memory technology for program storage and SRAM for data, with hardware AES encryption accelerator (on select variants) and a true random number generator on some family members. The 48-pin QFN package offers a compact footprint, low parasitic inductance, and excellent thermal dissipation through the exposed pad, enabling dense PCB layouts in industrial control and IoT designs. Typical applications include home-automation controllers, sensor node data loggers, low-power wireless sensor hubs, USB HID peripherals, smart metering endpoints, and industrial control modules. Compared with simple 8-bit MCUs, the Cortex-M0+ delivers a 4-5x MIPS/mW efficiency improvement, enabling longer battery life in remote sensor applications. When designing with this part, ensure that the exposed pad on the QFN package is soldered to a properly-sized copper pour (typically 5x5 mm of 1 oz copper minimum) to keep junction temperature within the -40C to +85C industrial operating range. Decouple VDDIN and VDDIO with at least 1 uF X7R ceramic bypass capacitors placed close to the pins to avoid inrush-current glitches during SERCOM or ADC operation. This page synthesizes distributor pricing, drop-in alternatives from the SAMD20 family, and practical design notes not found in the standalone manufacturer datasheet.

견적 요청 문의하기
ATSAMD20G14B-MUT - ARM Cortex-M0+ 48MHz 16KB Flash MCU | Microchip
ATSAMD20G14B-MUT

ATSAMD20G14B-MUT - ARM Cortex-M0+ 48MHz 16KB Flash MCU | Microchip

The Microchip Technology ATSAMD20G14B-MUT is a 32-bit ARM Cortex-M0+ flash microcontroller in the SAM D20G family, delivering 48 MHz CPU performance with 16 KB of Flash and 2 KB of SRAM in a 48-pin QFN (7x7 mm) package. It operates from a 1.62 V to 3.63 V supply and integrates 6 SERCOM (serial communication) interfaces, a 12-bit ADC, 10-bit DAC, and full-speed USB device support on selected variants. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and programmable peripherals on one silicon die. The SAM D20 family belongs to the broader hierarchy: ARM Cortex-M0+ core -> 32-bit RISC microcontroller -> embedded MCU -> semiconductor. The Cortex-M0+ architecture delivers Thumb-2 instruction efficiency at extremely low active and sleep currents, making this category the standard for battery-powered and always-on embedded designs. Key features include the Cortex-M0+ core with single-cycle I/O access, hardware multiplier, and atomic bit-banding in the peripheral address space. The device offers up to 38 GPIO lines, six SERCOM modules that can each be configured as USART, I2C, or SPI, a 12-channel 350 kSPS 12-bit ADC, a 10-bit 350 kSPS DAC, and two analog comparators. An 8-channel event system and a 16-bit real-time counter/counter with capture/compare (TC) and timer/counter for control (TCC) blocks enable precise PWM generation. The 'B' revision of the SAM D20G14 silicon adds Atmel START / Microchip Studio project compatibility, improved power-down current figures, and refined ADC gain/offset calibration. The 'U' package suffix indicates an extended industrial temperature grade (-40 °C to +85 °C), and the 'T' suffix denotes Tape & Reel packaging for high-volume surface-mount assembly. Typical applications include low-power IoT sensor nodes, home-automation controllers, smart-metering endpoints, consumer HMI keypads, and industrial sensor hubs. The combination of 16 KB Flash, 2 KB SRAM, and the Cortex-M0+ core comfortably fits protocols such as Bluetooth Low Energy controller stacks, LoRaWAN device drivers, Modbus RTU slaves, and small graphical user interfaces. Design consideration: place a 1 µF X7R bypass capacitor within 5 mm of each VDDCORE/VDDIO pin pair and use a 100 nF high-frequency decoupling cap directly on the analog AVDD rail to preserve ADC SNR. Keep the SWD clock and SWDIO traces length-matched and surrounded by GND to avoid debugger errors at 48 MHz. This page synthesizes distributor pricing, drop-in alternatives from the same SAM D20 family, and practical design notes that complement the manufacturer datasheet with engineer-friendly guidance.

견적 요청 문의하기
ATSAMD20G15A-ANT - 48MHz Cortex-M0+ MCU, 32KB Flash | TQFP-48 | Microchip
ATSAMD20G15A-ANT

ATSAMD20G15A-ANT - 48MHz Cortex-M0+ MCU, 32KB Flash | TQFP-48 | Microchip

The Microchip ATSAMD20G15A-ANT is a 32-bit ARM Cortex-M0+ flash microcontroller in a 48-pin TQFP (7x7 mm) package, featuring 32KB of flash, 4KB of SRAM, and a 48 MHz CPU clock. It operates from 1.6V to 3.6V and supports industrial temperature grades up to +105 C junction. The device integrates a 12-bit ADC, 10-bit DAC, 256-channel Peripheral Touch Controller (PTC), RTC, and up to six SERCOM configurable serial interfaces, delivering high peripheral density in a small surface-mount footprint. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (flash), working memory (SRAM), and programmable peripherals on one silicon die. The Cortex-M0+ core sits at the low-power end of the ARM Cortex-M family, balancing deterministic performance with minimal energy per instruction. Microcontrollers in this class form the foundation of embedded systems spanning home automation, metering, consumer electronics, and industrial sensors, where deterministic real-time response and low standby current are essential. Key features of the ATSAMD20G15G15 include an Event System that lets peripherals trigger each other without CPU intervention, reducing latency and current consumption, plus a SleepWalking capability that allows peripherals to operate while the CPU remains in deep sleep. The integrated PTC supports capacitive touch sensing, eliminating external touch controller ICs in many HMI designs. The SERCOM modules can be software-configured as UART, SPI, I2C, or LIN, giving designers maximum flexibility in a 48-pin budget. The device uses a 32-bit ARM Cortex-M0+ core built on a low-power CMOS process, with a 2.62 mA/MHz active current and multiple low-power modes down to deep sleep with full SRAM retention. The 12-bit ADC provides up to 350 ksps throughput across up to 14 channels, and the 10-bit DAC supports audio and waveform generation. Brown-out detection, watchdog timer, and RTC with calendar mode support battery-backed timekeeping. Typical applications include home automation devices, smart metering endpoints, consumer HMI with capacitive touch, industrial sensor nodes, low-cost wearables, and battery-powered IoT edge nodes. The wide 1.6V-3.6V supply range supports both single-cell Li-ion and 3.3V regulated rails. AEC-Q100 qualification is not part of this specific suffix; consult the -AUT variant for automotive grade. When designing with this device, verify that your 48-pin TQFP land pattern matches the published mechanical drawing, and consider migrating to the -AUT suffix for environments requiring -40C to +125C AEC-Q100 qualification. This page consolidates distributor pricing, drop-in pin-compatible alternatives, and practical design guidance not collated in the manufacturer datasheet.

견적 요청 문의하기
ATSAMD20G15A-AU - 48MHz Cortex-M0+ MCU, 32KB Flash | Microchip
ATSAMD20G15A-AU

ATSAMD20G15A-AU - 48MHz Cortex-M0+ MCU, 32KB Flash | Microchip

The Microchip (formerly Atmel) ATSAMD20G15A-AU is a 32-bit ARM Cortex-M0+ flash microcontroller running up to 48 MHz, equipped with 32 KB of Flash and 4 KB of SRAM, housed in a 48-pin TQFP (7x7 mm) package. It belongs to the SAM D20 family of low-power, high-performance MCUs targeting home automation, consumer, metering, and industrial applications. An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core designed by ARM Holdings as the smallest and most energy-efficient member of the Cortex-M family. The Cortex-M0+ sits within the broader taxonomy of microcontroller -> embedded processor -> system-on-chip (SoC) -> semiconductor. It combines Thumb-2 instruction set compatibility with a tightly coupled NVIC interrupt controller, making it well suited for deterministic real-time embedded control where low active power and standby current are critical. Key differentiating features of the ATSAMD20G15A-AU include the Cortex-M0+ core at 48 MHz delivering 0.93 DMIPS/MHz, 32 KB single-cycle Flash access, an integrated SERCOM module providing up to six configurable USART/SPI/I2C serial interfaces, a 12-bit ADC with up to 350 ksps throughput, a 10-bit DAC, and full-speed USB 2.0 device support via the embedded USB transceiver. The device also integrates a 16-bit timer/counter, RTC, and a 32-bit real-time clock with calendar mode. Power features include an active current under 70 uA/MHz and a deep-sleep current below 1 uA with RTC retention. Architecturally, the ATSAMD20G15A-AU uses a single-cycle hardware multiplier, single-cycle IO port access, and a peripheral event system that lets peripherals trigger each other without CPU intervention. The 1.62V to 3.6V supply range covers both 1.8V and 3.3V typical rails. The 48-pin TQFP footprint exposes up to 38 GPIO, the SERCOM channels, ADC inputs, USB D+/D-, SWD debug, and reset lines. Typical applications include low-power IoT sensor nodes, home automation controllers, smart metering endpoints, industrial HMI modules, USB HID peripherals, and battery-powered consumer devices. The combination of Cortex-M0+ efficiency, deep SleepWalking peripherals, and integrated USB makes this part a versatile general-purpose MCU for cost-sensitive designs. When designing with this MCU, allocate the 32 KB Flash carefully - reserve a dedicated bootloader region if you plan to use the SAM-BA or UF2 bootloader. Place a 1 uF decoupling capacitor close to VDD and a 0.1 uF capacitor on each VDDIO/VDDANA pin to meet the analog noise floor of the 12-bit ADC. This page synthesizes distributor pricing, same-family drop-in alternatives from Microchip's SAM D20 lineup, cross-brand Cortex-M0+ equivalents, application notes, and practical design guidance that goes beyond the manufacturer datasheet.

견적 요청 문의하기
ATSAMD20G15A-MN - ARM Cortex-M0+ MCU 48MHz 32KB Flash QFN-48
ATSAMD20G15A-MN

ATSAMD20G15A-MN - ARM Cortex-M0+ MCU 48MHz 32KB Flash QFN-48

The Microchip Technology ATSAMD20G15A-MN is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20G family, operating at up to 48 MHz with 32 KB of Flash and 4 KB of SRAM, housed in a 48-pin QFN (7x7 mm) package with an exposed thermal pad. It operates from a wide 1.62 V to 3.63 V supply and integrates 6 SERCOM (serial communication) peripherals, a 12-bit 350 ksps ADC, 10-bit DAC, and a full-speed USB 2.0 device interface in selected variants. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, and peripheral interfaces. The Cortex-M0+ is ARM's smallest and most energy-efficient 32-bit core, designed for deterministic real-time embedded workloads. The SAM D20 family sits within Microchip's broader portfolio of 32-bit microcontrollers, which serve applications ranging from consumer wearables to industrial automation and IoT edge nodes. The ATSAMD20G15A-MN specifically targets the 32 KB Flash / 4 KB SRAM tier of the family. Key features of the ATSAMD20G15A-MN include a hardware-based Event System for inter-peripheral signalling without CPU intervention, a Sleepwalking peripheral power manager that allows I/O to wake the core only when needed, and a single-cycle 32-bit hardware multiplier. The device offers 38 GPIO lines, 6 SERCOM channels that can each be configured as UART, SPI, or I2C, and a 12-bit 1 Msps ADC with up to 14 analog input channels. The integrated Full-Speed USB 2.0 device controller requires only an external 48 MHz crystal plus a few passive components. Architecturally, the ATSAMD20G15A-MN leverages a 2-layer AHB bus matrix that allows simultaneous peripheral DMA and CPU fetches, reducing stalls and lowering average power. The device ships with Microchip's Atmel START / MPLAB Harmony software framework support, including ASF (Advanced Software Framework) drivers and freeRTOS ports. The Cortex-M0+ core delivers 2.14 CoreMark/MHz, which translates to roughly 0.9 DMIPS/MHz, suitable for sensor fusion, protocol bridging, and simple user-interface applications. Typical applications for the ATSAMD20G15A-MN include home automation controllers, low-power wireless sensor nodes, industrial metering and HVAC peripherals, consumer wearables, and USB HID peripherals such as keyboards and custom input devices. The device's USB device controller makes it especially attractive for low-cost USB-C accessories, while the rich SERCOM complement suits sensor hubs and protocol-conversion bridges. When designing with the ATSAMD20G15A-MN, ensure the exposed pad (EP) is soldered to a continuous ground plane for both thermal and electrical performance. Decouple VDDCORE and VDDIO independently with 100 nF X7R capacitors placed within 3 mm of each supply pin, and provide a bulk 4.7 uF capacitor at the regulator output. The 48 MHz system clock source can be the internal 8 MHz RC oscillator multiplied by the on-chip PLL, or an external crystal; whichever is chosen must meet the USB 48 MHz +/- 0.25% accuracy budget for USB Full-Speed operation. This page synthesizes distributor pricing across seven channels, drop-in alternatives from the same Microchip SAM D20 family, and practical design notes beyond the manufacturer datasheet, giving engineers a single reference for sourcing, substitution, and PCB bring-up decisions.

견적 요청 문의하기
ATSAMD20G15A-MU - 48MHz Cortex-M0+ 32KB MCU | Microchip | SAM D20
ATSAMD20G15A-MU

ATSAMD20G15A-MU - 48MHz Cortex-M0+ 32KB MCU | Microchip | SAM D20

The Microchip Technology ATSAMD20G15A-MU is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20G family that operates at up to 48 MHz and integrates 32 KB of Flash and 4 KB of SRAM in a 48-pin QFN (7x7 mm) package. Key features include 6 SERCOM interfaces (configurable as I2C, SPI, or UART), a 12-bit ADC with up to 10 channels, a 10-bit DAC, six 16-bit timers/counters, and a full-speed USB 2.0 device port. The device operates from 1.62 V to 3.63 V supply voltage across the full industrial -40 C to +85 C temperature range. What is a low-power 32-bit microcontroller? This category of MCU combines the energy efficiency of an 8-bit core with the computational headroom of a 32-bit ARM Cortex-M0+ instruction set, making it ideal for battery-powered and always-on applications. The SAM D20 sits within Microchip's broader portfolio of ARM-based microcontrollers and shares the peripheral IP library of the SAM D21 family, allowing drop-in upgrades when more memory or USB host support is needed. Key specifications include 2.14 CoreMark/MHz, an Event System for inter-peripheral signaling without CPU intervention, a 32 kHz low-power oscillator, and support for Sleep, Idle, Standby, and Backup power modes that draw microamps of quiescent current. The 48-pin variant (G series) provides 38 programmable I/O pins and dual SERCOM options on most pads, enabling mixed serial-bus designs without external muxes. Technical depth: built on a low-leakage CMOS process, the ATSAMD20G15A uses a single-cycle hardware multiplier, a Nested Vectored Interrupt Controller (NVIC) with 32 IRQ lines, and a Serial Wire Debug interface. The peripheral event system and DMA controller allow latency-critical loops (e.g., ADC sampling or PWM updates) to run independently of the CPU, leaving headroom for application-layer code. Typical applications include home automation gateways, smart metering end-points, consumer wearables, IoT sensor nodes, and industrial HMI panels. The wide operating voltage range makes the part equally suitable for single-cell Li-ion / two-AA battery designs and 3.3 V industrial backplanes. Design consideration: leave at least 6 mm of uninterrupted copper ground beneath the exposed pad of the QFN-48 and stitch it to the system ground with 4 thermal vias for thermal and EMI performance, and never release reset while the core supply ramp is below 1.62 V. This page synthesizes distributor pricing across DigiKey, Mouser, and LCSC, lists drop-in same-package alternatives across the SAM D20 family, and provides practical design notes not consolidated in any single vendor product page.

견적 요청 문의하기