마이크로컨트롤러

제품 (18737)

ATSAME53N20A-AU-EFP - 120MHz Cortex-M4F MCU 1MB Flash TQFP-100
ATSAME53N20A-AU-EFP

ATSAME53N20A-AU-EFP - 120MHz Cortex-M4F MCU 1MB Flash TQFP-100

The Microchip Technology ATSAME53N20A-AU-EFP is a 32-bit ARM Cortex-M4F microcontroller from the SAM E53 high-performance family, running up to 120 MHz with single-precision FPU and DSP extensions, packaged in a 100-pin TQFP (14x14 mm). It integrates 1 MB Dual-Panel Flash with ECC, 256 KB SRAM with ECC, and a 10/100 Ethernet MAC, targeting connected industrial and IoT edge applications requiring deterministic real-time performance and on-board connectivity. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals including timers, communication interfaces, and analog blocks. Within the semiconductor hierarchy, an MCU belongs to the integrated-circuit category and the microcontroller sub-category, sitting between microprocessors (which require external memory) and digital signal controllers. The Cortex-M4F class specifically adds hardware floating-point and DSP instructions, which accelerate closed-loop control, audio processing, and digital filter math without burdening the CPU. Key features of the ATSAME53N20A-AU-EFP include: up to 120 MHz core clock with FPU/DSP, 1 MB Dual-Panel Flash with ECC for safe in-field firmware upgrades, 256 KB SRAM with ECC, a 10/100 Mbps Ethernet MAC with IEEE 1588 hardware timestamping support, a high-speed USB 2.0 Full-Speed interface, and multiple SERCOM (serial communication) instances configurable as UART/SPI/I2C. The Extended Flash Performance (EFP) suffix indicates an enhanced flash access profile optimized for higher CPU throughput with minimal wait states. Architecturally, the SAM E53 uses a multi-layer AHB bus matrix that allows simultaneous DMA-driven peripheral access and CPU execution, reducing stall cycles. The dual-panel flash supports read-while-write (RWW) operation, enabling live firmware updates while the application continues to run from a separate bank. Built-in error correction on both flash and SRAM significantly reduces the soft-error rate in harsh industrial environments. Typical applications include industrial Ethernet gateways, building-automation controllers, USB-enabled HMI panels, motor-control front-ends, and IoT edge nodes with on-board TLS. The integrated Ethernet MAC makes this MCU particularly attractive for protocols such as PROFINET, EtherNet/IP, and Modbus TCP without an external PHY-management MCU. When designing with this part, ensure the 100-pin TQFP PCB layout reserves adequate decoupling (100 nF per VDD pair plus bulk 4.7 uF) within 5 mm of the supply pins. Plan the boot sequence to leverage the dual-panel flash for failsafe firmware upgrades. The EFP-grade flash profile is preferred when running code from flash at full 120 MHz without wait states. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

견적 요청 문의하기
ATSAME53N20A-AUT-EFP - 120MHz Cortex-M4F MCU 1MB Flash 100-TQFP | Microchip
ATSAME53N20A-AUT-EFP

ATSAME53N20A-AUT-EFP - 120MHz Cortex-M4F MCU 1MB Flash 100-TQFP | Microchip

The Microchip ATSAME53N20A-AUT-EFP is a 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz, integrating 1 MB of dual-panel Flash with ECC and 256 KB of SRAM with ECC in a 100-pin TQFP (14x14 mm) package. The device is part of the SAM E53 family, which combines a high-performance Cortex-M4 core with FPU, a 10/100 Ethernet MAC, USB 2.0 Full-Speed with on-chip transceiver, and CAN-FD peripherals. The -EFP suffix indicates the Extended Flash Performance variant shipped in Tape & Reel. A microcontroller (MCU) is a single-chip processor that integrates CPU, memory, and programmable peripherals on one die, enabling embedded control without external memory or logic devices. The Cortex-M4F core in the SAM E53 family is one step above Cortex-M3 cores in Microchip's SAM lineup, adding single-precision Floating Point Unit (FPU) hardware, DSP extensions, and tightly coupled peripherals for deterministic industrial communication. The SAM E53 sits within Microchip's power-managed MCU hierarchy: Cortex-M0+ (SAML/SAMC) -> Cortex-M4 (SAMD5x) -> Cortex-M4F with FPU (SAME5x) -> Cortex-M7 (SAMS70).

견적 요청 문의하기
ATSAME54N19A-AF - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip
ATSAME54N19A-AF

ATSAME54N19A-AF - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip

The Microchip Technology ATSAME54N19A-AF is a high-performance 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with single-precision FPU, integrating 512 KB dual-panel Flash with ECC and 192 KB SRAM with ECC, housed in a 100-pin TQFP (14x14 mm) package. The SAM E54 family is part of Microchip's SAM D5x/E5x platform targeting industrial automation, automotive body/comfort, and connected IoT edge nodes. This specific -AF suffix variant is the automotive temperature grade (-40C to +125C), 100-pin TQFP, tray-packaged member. A Cortex-M4F microcontroller (MCU) is a 32-bit processor core licensed from Arm that combines the M4 instruction set with a hardware single-precision Floating Point Unit, an MPU for memory protection, and optional DSP extensions. It sits in the middle of the Arm Cortex-M family between the M3 (no FPU) and M7 (superscalar with double-precision FPU). Within the broader taxonomy: Cortex-M4F MCU -> 32-bit microcontroller -> microcontroller -> embedded processor -> semiconductor. The SAM E54 specifically belongs to the Cortex-M4F-based high-performance tier with extensive connectivity peripherals. Key features include 120 MHz CPU clock, 512 KB Flash with error correction, 192 KB SRAM, full-speed USB 2.0 with on-chip PHY, dual CAN-FD controllers, Ethernet MAC (10/100), 10/100-Mbps I2S audio interface, SD/MMC host, and up to six SERCOM (serial communication) modules configurable as UART/SPI/I2C. The device also integrates a 12-bit 1 MSPS ADC, two 12-bit DACs, four analog comparators, and a high-speed Host/Client USB 2.0 port. An 8-channel Event System, 16-bit timers, and a TCC (Timer/Counter for Control) supporting motor-control PWM make it suitable for closed-loop control. The ATSAME54N19A-AF uses the Cortex-M4F core's branch prediction, single-cycle MAC, and SIMD instructions to deliver 150 Dhrystone MIPS and 1.25 DMIPS/MHz. The dual-panel Flash allows read-while-write (RWW) for safe firmware updates, and ECC on both Flash and SRAM mitigates soft-error risk in industrial and automotive environments. TrustZone-M is not present on this device (it is on the Cortex-M33 SAM L11/E11 families), but a separate secure boot and cryptographic accelerator (AES, SHA, TRNG) is integrated. Typical applications include industrial PLCs and HMIs, automotive body and comfort modules, smart metering, building automation gateways, motor control BLDC drivers, USB-connected medical peripherals, and Human-Machine Interface panels with TFT displays. The wide operating temperature range of -40C to +125C suits automotive and industrial enclosures. When designing with this device, pay attention to decoupling: place 100 nF X7R ceramics adjacent to every VDD pin pair and a bulk 4.7 uF on each main rail. The integrated Ethernet MAC requires an external PHY (e.g., KSZ8081) and 49.9 ohm 1% termination on the differential pair. Firmware should enable the watchdog timer and use the dual-panel Flash for A/B OTA updates. This page synthesizes distributor pricing, automotive-grade drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

견적 요청 문의하기
ATSAME54N19A-AU - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip
ATSAME54N19A-AU

ATSAME54N19A-AU - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip

The Microchip Technology ATSAME54N19A-AU is a 32-bit ARM Cortex-M4F microcontroller from the SAM E54 family, integrating a Floating Point Unit (FPU) and running at speeds up to 120 MHz. It provides 512 KB of dual-panel Flash memory with ECC and 192 KB of SRAM with ECC, housed in a 100-pin TQFP (14x14 mm) industrial-grade package rated for -40C to +85C operation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals. The Cortex-M4F belongs to ARM's Cortex-M family of energy-efficient processors designed for embedded deterministic real-time control. Within the SAM E54 series, the ATSAME54N19A-AU sits in the Cortex-M4F -> Cortex-M -> 32-bit MCU -> embedded processor hierarchy, targeting industrial HMI, connectivity gateways, and audio processing applications. Key features include the Cortex-M4F core with single-precision FPU and DSP extensions, a high-speed on-chip 12-bit 1 Msps ADC, USB 2.0 Full-Speed with on-chip PHY, a 100 MHz system bus, multiple SERCOM channels configurable as UART/SPI/I2C, an I2S interface for digital audio, a 16-bit HSMCI for SD card storage, and a Crypto Accelerator (TRNG, AES, SHA). The 100-TQFP package provides ample I/O for parallel TFT displays and external memory buses. The SAM E54 architecture uses a multi-layer AHB bus matrix connecting the CPU, DMA controllers, and peripherals, allowing concurrent access with deterministic latency. The dual-panel Flash subsystem enables live firmware updates and EEPROM emulation, while the SRAM with ECC supports safety-critical applications where single-bit errors must be corrected automatically. Typical applications include industrial HMI panels with TFT displays, smart energy metering, IoT edge nodes with USB connectivity, digital audio streaming devices using I2S, and automotive aftermarket infotainment controllers. Designers value the on-chip FPU for sensor-fusion algorithms and the integrated crypto block for secure boot implementations. When designing with the ATSAME54N19A-AU, ensure 100 nF and 4.7 uF decoupling caps are placed near each VDD pin pair, and that the 12 MHz crystal or external clock meets the accuracy requirements specified in the SAM E54 datasheet. For USB applications, the DP/DM trace impedance must be tuned to 90 ohms differential.

견적 요청 문의하기
ATSAME54N19A-AU-EFP - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip
ATSAME54N19A-AU-EFP

ATSAME54N19A-AU-EFP - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip

The Microchip Technology ATSAME54N19A-AU-EFP is a 32-bit ARM Cortex-M4F microcontroller from the SAM E54 family, operating up to 120 MHz with 512 KB Flash and 192 KB SRAM in a 100-pin TQFP (14x14 mm) package. The integrated Floating Point Unit (FPU) and DSP extensions deliver high-performance signal processing while the dual-panel Flash with ECC provides reliable code storage for safety-critical applications. Key features include a 120 MHz Cortex-M4F core, 512 KB dual-panel Flash with ECC, 192 KB SRAM with ECC, full-speed USB 2.0 with integrated PHY, 10/100 Mbps Ethernet MAC with IEEE 1588 support, CAN-FD, and a 12-bit 1 MSPS ADC with up to 16 channels. Extended Flash Performance (-EFP) variant increases Flash endurance to 100k cycles and improves retention for industrial and automotive-grade deployments. The architecture integrates a 5-channel Direct Memory Access controller, Event System for hardware-triggered task chaining, and SERCOM peripherals configurable as UART, SPI, I2C, or LIN. The 14x14 TQFP-100 footprint provides ample GPIO for motor control, HMI, and multi-protocol gateway designs where pin count directly impacts board layout. Typical applications include industrial IoT gateways, motor control (BLDC/PMSM FOC), building automation controllers, USB peripherals with Ethernet bridging, and human-machine interfaces with TFT displays. The combination of CAN-FD, Ethernet, and USB makes the device a strong fit for connected industrial nodes where deterministic communication is required. When designing, ensure the trace impedance for USB and Ethernet is calculated per USB 2.0 and IEEE 802.3 specifications. The on-chip voltage regulator requires a 1uF X7R bypass capacitor close to VDDCORE; missing this capacitor results in unstable operation. Decouple each VDDIO group separately to minimize digital switching noise coupling into the analog ADC rails. This page consolidates distributor pricing for the ATSAME54N19A-AU-EFP, drop-in compatible ATSAME5x family members, and engineering guidance not found in the manufacturer datasheet alone.

견적 요청 문의하기
ATSAME54N19A-AUT - 120MHz Cortex-M4F MCU 512KB Flash | Microchip
ATSAME54N19A-AUT

ATSAME54N19A-AUT - 120MHz Cortex-M4F MCU 512KB Flash | Microchip

The Microchip Technology ATSAME54N19A-AUT is a 32-bit ARM Cortex-M4F microcontroller from the SAM E54 family running up to 120 MHz with a single-precision floating point unit, packaged in a 100-pin TQFP (14x14 mm) and qualified for the automotive -40C to +85C temperature range. It integrates 512 KB of Flash with ECC and 256 KB of SRAM with ECC, providing robust memory integrity for safety-critical embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, and configurable peripherals on one die. The Cortex-M4F core sits inside the ARM Cortex-M family, which targets deterministic real-time embedded control. The same-family members (SAM E51, SAM E53, SAM E54, SAMD51) share the Cortex-M4F architecture, peripheral set, and toolchain (Microchip Studio, MPLAB X, Harmony), allowing software portability across products that scale in flash, RAM, and pin count. Key features of the ATSAME54N19A-AUT include a 120 MHz Cortex-M4F core with DSP extensions, 512 KB dual-panel Flash, 256 KB SRAM, a high-speed 12-bit ADC up to 1 MSPS, USB 2.0 Full-Speed with embedded Host and Device, CAN-FD, multiple SERCOM, I2S, and a hardware cryptographic module. The automotive temperature grade (-40C to +85C) and the AUT suffix indicate conformance with Microchip's automotive qualification flow. The device uses a sophisticated bus matrix (AHB/APB) with separate code and system buses for deterministic DMA and interrupt latency, supporting both code execution from Flash with zero-wait-state via the FPU and efficient DSP filter operations. The dual-panel Flash architecture enables live firmware updates without downtime, while ECC on Flash and SRAM detects and corrects single-bit errors in mission-critical applications. Typical applications include automotive body and infotainment modules, industrial control panels, USB peripherals, CAN-FD gateways, motor control, and secure connected IoT nodes. Designers choose it when they need ARM Cortex-M4F DSP performance, automotive temperature range, USB and CAN-FD connectivity, and an integrated crypto accelerator in a 100-pin TQFP footprint. When laying out the PCB, dedicate at least one solid ground plane beneath the device, place the 0.1 uF VDD decoupling capacitors within 5 mm of each VDD pin, and reserve the SWD/SWC pins for programming. The 100-pin TQFP requires thermal vias under the die-attach pad; the pad is internally connected to ground but should still receive multiple stitching vias for stable operation at high ambient temperature. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that complement the manufacturer datasheet with engineering decision support.

견적 요청 문의하기
ATSAME54N20A-AF - 120MHz Cortex-M4F MCU, 1MB Flash | Microchip
ATSAME54N20A-AF

ATSAME54N20A-AF - 120MHz Cortex-M4F MCU, 1MB Flash | Microchip

The Microchip ATSAME54N20A-AF is a high-performance 32-bit ARM Cortex-M4F microcontroller from the SAM E54 family, running up to 120 MHz with an integrated single-precision Floating Point Unit (FPU). It integrates 1 MB of dual-panel Flash with ECC and 256 KB of SRAM with ECC, housed in a 100-pin TQFP (14x14 mm) extended-temperature package. According to the Microchip product page, the device targets industrial, automotive, and connectivity-rich embedded designs where deterministic real-time response and DSP-class arithmetic throughput are required. A microcontroller (MCU) is a single-chip computer integrating a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals. Within the embedded hierarchy, the ATSAME54N20A-AF sits at the high-performance ARM Cortex-M tier above Cortex-M0/M0+ entry-level MCUs and below Cortex-M7 application processors. The Cortex-M4F specifically adds DSP extensions and an FPU, enabling on-chip signal-processing without an external DSP coprocessor. Key differentiating features include a 120 MHz CPU with FPU, 1 MB dual-panel Flash allowing live firmware updates, 256 KB SRAM, full-speed USB 2.0 with integrated PHY, 10/100 Mbps Ethernet MAC with IEEE 1588 support, CAN-FD, multiple SERCOM configurable serial interfaces, a 12-bit 1 Msps ADC, DACs, and a hardware crypto block. The SAM E54 also exposes a Parallel Capture Controller (PCC) for camera and display interfaces, making it suitable for vision and HMI subsystems. Architecturally, the SAM E54 uses a bus matrix with separate AHB/APB domains giving the Cortex-M4F core simultaneous access to Flash, SRAM, and peripherals via the multi-port SRAM controller. The dual-panel Flash subsystem supports EEPROM emulation and live firmware swap. Hardware cryptographic accelerators (AES, SHA, TRNG) offload secure-boot and TLS workloads, while the Event System and Direct Memory Access Controller (DMAC) enable low-latency, CPU-offloaded data movement between peripherals and memory. Typical applications include industrial Ethernet gateways, PLC communication modules, building-automation controllers, USB peripherals, CAN-FD automotive body-domain modules, IoT edge nodes with TLS, and audio-processing front ends leveraging the DSP/FPU. The extended-temperature grade suits outdoor and automotive under-hood environments. When designing with this device, pay particular attention to decoupling strategy: place 100 nF X7R capacitors within 2 mm of every VDD pin, and provide a bulk 4.7 uF capacitor on each power domain. The 14x14 mm TQFP allows easy hand-soldering and rework, but its exposed pad must be soldered to a properly sized ground copper pour for thermal dissipation. This page synthesizes Microchip datasheet specifications, real-time distributor pricing as of 2026-09-21, drop-in TQFP-100 alternatives from the SAM E54/SAME5x family, and practical PCB design notes not consolidated in any single source.

견적 요청 문의하기
ATSAME54N20A-AFT - 120MHz Cortex-M4F MCU, 1MB Flash, TQFP-100 | Microchip
ATSAME54N20A-AFT

ATSAME54N20A-AFT - 120MHz Cortex-M4F MCU, 1MB Flash, TQFP-100 | Microchip

The Microchip Technology ATSAME54N20A-AFT is a high-performance 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with single-precision Floating Point Unit (FPU), 1 MB of dual-panel Flash with ECC, and 256 KB SRAM with ECC, packaged in a 100-pin TQFP (14x14 mm). It also integrates a 10/100 Ethernet MAC and 2x CAN-FD controllers, making it well suited for connected industrial designs. A microcontroller (MCU) is an integrated circuit that combines a processor core, program and data memory, peripherals, and I/O onto a single chip. The ARM Cortex-M4F is a mainstream MCU core class widely used in industrial automation, motor control, and connected devices; it sits below Cortex-M7 in performance and above Cortex-M0+ in DSP capability. Microchip's SAM E54 family specifically targets applications needing both deterministic real-time control and high-bandwidth wired connectivity (Ethernet/CAN-FD). Key features include 120 MHz Cortex-M4F with FPU, 1 MB Flash with ECC, 256 KB SRAM with ECC, hardware cryptographic accelerator, I2S audio interfaces, 12-bit ADC/DAC, 16-bit timers, and a 12-channel DMA. The QSPI and SDHC peripherals enable external memory expansion for data logging or display buffering. The device uses a Harvard-bus architecture with tightly-coupled memories (TCM) and a multi-layer bus matrix, allowing parallel access to Flash, SRAM, and peripherals without contention. ECC on both Flash and SRAM improves reliability for industrial environments subject to soft-error events; the dual-panel Flash architecture supports in-field updates without halting execution (live update). Typical applications include industrial Ethernet gateways, building automation controllers, CAN-FD automotive body controllers (non-safety), USB-C charging hubs with Type-C PD, and human-machine interface (HMI) panels. The combination of Ethernet MAC + CAN-FD + USB makes it especially attractive for Industry 4.0 edge nodes and IoT appliances. When designing with this MCU, plan the clock tree early: the SAME54 requires a 32.768 kHz crystal for the RTC/DFLL and a main crystal or external clock for the PLL feeding the 120 MHz CPU clock. Decouple each VDD/VSS pin pair with 100 nF X7R ceramics placed as close as possible. For Ethernet, observe strict PCB layout guidelines (controlled impedance, ground pour stitching) per the SAME54 Ethernet PHY interface design checklist. This page synthesizes distributor pricing, drop-in alternatives within the SAME5x family, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
ATSAME54N20A-AU - 120MHz Cortex-M4F MCU 1MB Flash 100-TQFP | Microchip
ATSAME54N20A-AU

ATSAME54N20A-AU - 120MHz Cortex-M4F MCU 1MB Flash 100-TQFP | Microchip

The Microchip ATSAME54N20A-AU is a 32-bit ARM Cortex-M4F microcontroller from the SAM E54 family, running up to 120 MHz with an integrated single-precision Floating Point Unit (FPU), 1 MB of dual-panel Flash with ECC, and 256 KB of SRAM with ECC, packaged in a 100-pin TQFP (14x14 mm). A microcontroller (MCU) is an integrated circuit that combines a processor core, program and data memory, and a rich set of on-chip peripherals around a single silicon die. The Cortex-M4F sits in the middle of the ARM Cortex-M taxonomy - between the smaller Cortex-M0+ (cost-optimised) and the larger Cortex-M7 (higher performance DSP). Within Microchip's portfolio, the SAM E54 belongs to the SAM D5x/E5x family and ranks among the highest-pin-count, highest-memory Cortex-M4F offerings before stepping up to Cortex-M7 (SAM S70/E70). Key features of the ATSAME54N20A-AU include: 120 MHz core clock, 1 MB dual-panel Flash with error correction, 256 KB SRAM with ECC, a 10/100 Ethernet MAC, two CAN-FD controllers, a high-speed USB 2.0 (480 Mbit/s) interface with on-chip HS PHY, a 12-bit 1 Msps ADC, two 12-bit 1 Msps DACs, SERCOM (configurable serial) peripherals, and an on-chip crypto accelerator (AES, True Random Number Generator). The 100-TQFP package exposes the full peripheral set including external memory bus and high-pin-count analog/digital features. Architecturally, the SAM E54 uses a Harvard-style bus with separate AHB/APB matrices, enabling simultaneous Flash fetch, peripheral DMA, and Ethernet traffic. The dual-panel Flash allows one bank to be erased/written while the other executes code, supporting in-field firmware updates without downtime. The FPU executes single-precision IEEE 754 instructions in a single cycle, accelerating DSP and sensor-fusion workloads. Typical applications include industrial automation controllers, building-automation gateways, IoT edge nodes with Ethernet connectivity, automotive body and infotainment subsystems, medical patient-monitoring devices, and USB-connected human-interface peripherals. The integrated Ethernet MAC and HS USB PHY make it especially suitable for connected products that previously required an external PHY or a separate interface chip. When designing with the ATSAME54N20A-AU, plan power-rail sequencing so the 3.3 V analog supply (VDDANA) settles within 10 ms of the digital 3.3 V rail to keep the BOR/POR reset path deterministic. Decoupling: place a 100 nF X7R on every VDD pin and a bulk 4.7 µF near the package. For Ethernet, route the RMII traces length-matched to within 50 mil and keep them over a continuous ground plane. This page synthesises distributor pricing, drop-in same-family alternatives, application recommendations, and practical design notes not aggregated in a single place on the manufacturer product page or typical distributor listings.

견적 요청 문의하기
ATSAME54N20A-AU-EFP - 120MHz Cortex-M4F MCU, 1MB Flash | Microchip
ATSAME54N20A-AU-EFP

ATSAME54N20A-AU-EFP - 120MHz Cortex-M4F MCU, 1MB Flash | Microchip

The Microchip Technology ATSAME54N20A-AU-EFP is a high-performance 32-bit ARM Cortex-M4F microcontroller from the SAM E54 family, integrating an FPU, DSP extensions, up to 1 MB of dual-panel Flash with ECC, and up to 256 KB of SRAM with ECC, all housed in a 100-pin TQFP (14x14 mm) package. It operates at up to 120 MHz and is designed for applications requiring deterministic real-time control combined with rich connectivity, including high-speed USB, 10/100 Ethernet, and CAN-FD. The -AU-EFP variant designates a Tray-packaged, AEC-Q100-qualified automotive-grade part with Microchip's Extended Flash Performance (EFP) endurance option. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals including timers, communication controllers, and analog blocks. The SAM E54 belongs to the Cortex-M4F class, which is a microcontroller architecture that adds a single-precision Floating-Point Unit and DSP instructions to the Cortex-M4 baseline. Within the broader hierarchy, the ATSAME54N20A-AU-EFP sits as: ARM Cortex-M4F core -> Cortex-M4 family -> ARM Cortex-M -> 32-bit RISC processor -> microcontroller -> embedded computing platform -> semiconductor device. Key features include 120 MHz CPU core with FPU and DSP, 1 MB Flash and 256 KB SRAM (both with ECC), high-speed USB 2.0 Full-Speed with on-chip PHY, 10/100 Mbps Ethernet MAC with IEEE 1588 PTP hardware support, two CAN-FD controllers, multiple SERCOM interfaces configurable as UART/SPI/I2C, a 12-bit 1 Msps ADC, dual 12-bit DACs, and a Cryptographic Engine supporting AES, True Random Number Generator, and secure boot. The TQFP-100 package exposes up to 84 GPIO lines and supports automotive operating temperature range of -40C to +125C. The SAM E54 architecture uses a multi-layer AHB/APB bus matrix that allows simultaneous DMA-driven peripheral and CPU activity, reducing interrupt load and improving deterministic response. ECC on Flash and SRAM is critical for ASIL-B functional safety paths and for industrial environments subject to alpha-induced soft errors. The integrated Ethernet MAC with 1588 PTP timestamping supports industrial automation protocols such as EtherCAT, PROFINET, and Modbus TCP without an external PHY timing MCU. Typical applications include industrial EtherCAT slave controllers, automotive body and gateway modules, USB-C audio interfaces, building automation controllers, and IEC 61508 SIL-2 capable safety systems. The combination of CAN-FD, Ethernet, and high-speed USB makes it especially suited for vehicle networking gateways that bridge CAN-FD body domains with Ethernet backbone networks. When designing with this device, ensure VDDIO and VDDCORE decoupling follow the manufacturer's reference layout with at least four 100 nF X7R capacitors and a single 4.7 uF bulk per rail. Configure the GCLK generator to lock the DFLL48M to the 32.768 kHz crystal before enabling the Ethernet MAC, since the MAC requires a 50 MHz or 25 MHz reference derived from a precise clock source. For automotive projects, prefer the Q1A suffix variants (this part is automotive-grade via -AU) and validate OTP memory lock bits before production flashing. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATSAME54N20A-AUT - 120MHz ARM Cortex-M4F MCU, 1MB Flash | Microchip
ATSAME54N20A-AUT

ATSAME54N20A-AUT - 120MHz ARM Cortex-M4F MCU, 1MB Flash | Microchip

The Microchip Technology ATSAME54N20A-AUT is a 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with single-precision Floating Point Unit (FPU), 1 MB of Dual-Panel Flash with ECC, and 256 KB of SRAM with ECC, housed in a 100-pin TQFP (14x14 mm) package qualified for the automotive -40C to +85C range. What is an ARM Cortex-M4F microcontroller? It is a 32-bit microcontroller core based on the ARMv7-M architecture with hardware single-precision floating point, DSP extensions, and a Nested Vectored Interrupt Controller (NVIC). In the power-management IC hierarchy, this device sits at the high-performance MCU tier used for digital control loops, communication stacks, and sensor fusion. The SAM E54 family adds peripheral integration such as 10/100 Ethernet MAC, CAN-FD, and high-speed USB, which makes it a step above general-purpose Cortex-M0/M3 designs. Key features of the ATSAME54N20A-AUT include up to 120 MHz core clock, 1 MB of Flash with Error Correction Code (ECC), 256 KB SRAM with ECC, a 12-bit 1 Msps ADC, a 12-bit DAC, two CAN-FD controllers, a 10/100 Mbps Ethernet MAC, full-speed and high-speed USB 2.0 with on-chip PHY, and a QSPI/SPI interface supporting external memory. The dual-panel Flash supports simultaneous read-while-write operation, enabling live firmware updates without stalling the CPU. The Cortex-M4F core delivers 1.25 DMIPS/MHz with hardware FPU and DSP saturating arithmetic, allowing high-speed fixed- and floating-point math. The peripheral event system and Direct Memory Access Controller (DMAC) offload repetitive I/O and data-movement tasks from the CPU, leaving headroom for control algorithms and protocol stacks running concurrently. Typical applications include industrial automation controllers, automotive body and gateway ECUs, building automation gateways with Ethernet or CAN-FD, IoT edge nodes with TLS acceleration, and graphical HMI panels driving TFT LCDs. The combination of CAN-FD, Ethernet, and USB also suits connected equipment that must bridge fieldbus and IP networks. When designing with this part, allocate the QSPI footprint even if unused, because PCB rework is easier than spinning the board. Always add a 32.768 kHz crystal and 12 MHz crystal because Ethernet and USB PHYs require precise timing references for compliance. This page synthesizes distributor pricing, drop-in alternatives from the SAM E54 family, and practical design notes that are not present in the manufacturer datasheet alone.

견적 요청 문의하기
ATSAME54P19A-AU - 120MHz Cortex-M4F MCU 512KB Flash | Microchip
ATSAME54P19A-AU

ATSAME54P19A-AU - 120MHz Cortex-M4F MCU 512KB Flash | Microchip

The Microchip Technology ATSAME54P19A-AU is a 32-bit ARM Cortex-M4F microcontroller from the SAM E54 family, operating at up to 120 MHz with 512 KB of Flash and 128 KB of SRAM in a 128-pin TQFP (14x14) package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash and SRAM), and a rich set of peripherals into one IC. ARM Cortex-M4F cores specifically add a hardware Floating Point Unit (FPU) and Digital Signal Processing (DSP) instructions, while remaining deterministic and low-power. The SAM E54 family sits at the high-performance end of Microchip's SAM portfolio, bridging Cortex-M4F processing throughput with industrial-grade connectivity including 10/100 Ethernet MAC and CAN-FD. Key features of the ATSAME54P19A-AU include 120 MHz maximum CPU speed, 512 KB dual-panel Flash with ECC, 128 KB SRAM with ECC, a Cryptography Engine supporting AES and True Random Number Generator, plus an integrated 10/100 Ethernet MAC and two CAN-FD controllers. The part also integrates a high-speed USB 2.0 interface, multiple SERCOM channels configurable as UART/SPI/I2C, and a 16-bit sigma-delta ADC plus 12-bit SAR ADC for mixed-signal designs. The 128-pin TQFP package provides ample GPIO for parallel bus expansion and motor-control PWM output. Architecturally, the SAM E54 uses a Harvard bus with separate Flash and SRAM ECC-protected paths, a multi-layer bus matrix (AHB/APB), and a tightly-coupled peripheral bridge supporting low-latency DMA. Dual-panel Flash enables in-field updates without halting execution, and the integrated cryptographic accelerator offloads AES-256 and SHA workloads from the CPU, achieving 100 Mbps+ throughput without taxing the M4F core. Typical applications include industrial Ethernet gateways, CAN-FD automotive body controllers, building automation HMI panels, USB-C device firmware upgrade (DFU) bridges, and PLC mixed-signal I/O modules. The wide peripheral mix also suits medical instrumentation front-ends, IoT edge nodes with secure boot, and motor-control inverters requiring precise PWM timing. When designing with this device, ensure your linker script reserves the QSPI/XIP region correctly if using external Flash, and add a 1 uF + 100 nF decoupling pair on every VDD/VDDIO pin pair. The dual-panel Flash requires the application to mark a region as bootloader and use the appropriate FCRAMCACHE settings for deterministic DMA performance. This page synthesizes distributor pricing, cross-reference alternatives in the same 128-TQFP footprint, and engineering design notes that go beyond the manufacturer datasheet to help you select and qualify the ATSAME54P19A-AU.

견적 요청 문의하기
ATSAME54P19A-AU-EFP - 120MHz Cortex-M4F MCU 512KB | Microchip
ATSAME54P19A-AU-EFP

ATSAME54P19A-AU-EFP - 120MHz Cortex-M4F MCU 512KB | Microchip

The Microchip Technology ATSAME54P19A-AU-EFP is a 32-bit ARM Cortex-M4F microcontroller from the SAM E54 family, running up to 120 MHz with 512 KB Flash and 128 KB SRAM, housed in a 128-pin TQFP (14x14 mm) package with extended Flash Performance and -40C to +85C industrial operating range. The "-AU" suffix denotes the 128-TQFP package, "-EFP" denotes Extended Flash Performance variant, and the part is supplied in tray packaging. A microcontroller (MCU) is a single-chip computer integrating a CPU core, Flash program memory, SRAM data memory, and a rich set of peripherals (ADC, timers, communication controllers). The Cortex-M4F is ARM's mainstream core for mixed signal control, adding a single-precision Floating-Point Unit (FPU) and DSP extensions. Within Microchip's hierarchy the SAM E54 sits above the SAMD5x and below the SAME70 in the SAM E family, targeting motor control, industrial connectivity, and graphical HMI applications. Key features of the ATSAME54P19A include 120 MHz Cortex-M4F core with FPU and DSP, 512 KB dual-panel Flash with ECC, 128 KB SRAM with ECC, Full-Speed USB with embedded PHY, a 10/100 Mbps Ethernet MAC with IEEE 1588 support, CAN-FD, up to 6 SERCOM serial interfaces, a 12-bit ADC up to 1 Msps, and a 12-bit DAC. Security features include a true random number generator (TRNG), AES crypto accelerator, secure boot, and Flash OTP region. The device integrates a sophisticated 8-channel DMA, Event System for inter-peripheral signalling without CPU intervention, and a Parallel Capture Controller for camera or external bus interfacing. The dual-panel Flash with ECC supports in-field FW upgrades without processor stall, while the 4 KB unified cache reduces Flash access stalls on the Cortex-M4F. The 1.71-3.63V VDD range allows direct operation from a single Li-ion cell or 3.3V regulated rail. Typical applications include industrial motor drives (BLDC, stepper, FOC), industrial gateways supporting Ethernet/IP or CANopen, building automation controllers, USB-CDC peripherals, solar inverters with MPPT, smart energy meters, and small graphical HMI panels. The combination of Cortex-M4F DSP, FPU and hardware crypto makes it well suited for edge nodes performing sensor fusion. When designing with this part, ensure that the 128-TQFP land pattern observes 0.4 mm pitch and that the exposed pad is soldered to a thermal copper pour for heat dissipation. For Ethernet designs, an external PHY (such as KSZ8081) is required as only the MAC is integrated. Decouple each VDD pin with 100 nF X7R placed within 2 mm of the pin. This page synthesizes distributor pricing, drop-in alternatives sourced from Microchip's Form-Fit-Function cross-reference, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATSAME54P19A-AUT-EFP - 120MHz Cortex-M4F MCU 512KB Flash | Microchip
ATSAME54P19A-AUT-EFP

ATSAME54P19A-AUT-EFP - 120MHz Cortex-M4F MCU 512KB Flash | Microchip

The Microchip Technology ATSAME54P19A-AUT-EFP is a 32-bit ARM Cortex-M4F microcontroller from the SAM E54 family, featuring a 120 MHz CPU with single-precision Floating Point Unit (FPU), 512 KB of Flash, and 192 KB of SRAM in a 128-pin TQFP (14x14 mm) package with Extended Flash Performance and automotive temperature grade. The "AUT" suffix denotes Tape & Reel packaging for high-volume assembly and the 85C automotive temperature rating, while the "EFP" extension marks the Extended Flash Performance variant with higher flash endurance and retention for industrial/automotive designs requiring extended reliability. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, and peripheral interfaces on one die. The ATSAME54 belongs to the SAM E54 series, which sits in Microchip's high-performance MCU portfolio alongside the SAM D5x family, targeting applications that require Cortex-M4 class DSP and FPU performance plus high-speed connectivity such as USB, Ethernet, and CAN-FD. Within the system hierarchy, this MCU is a processing subsystem that interfaces with sensors, communication transceivers, and memory, typically powered by 3.3 V and managed via an RTOS or bare-metal firmware. The ATSAME54P19A-AUT-EFP integrates 512 KB of dual-bank Flash with ECC, 192 KB SRAM, a full-speed USB 2.0 High-Speed interface, 10/100 Mbps Ethernet MAC with 1588 PTP support, CAN-FD, SD/MMC host, and a QSPI/SPI interface for external memory expansion. It also includes a 12-bit 1 Msps ADC, dual 12-bit DACs, analog comparators, and a hardware cryptographic accelerator (AES, SHA, TRNG) for secure connectivity. Up to 99 GPIO lines and a 16-bit HSMCI bus round out the peripheral set, making this device a versatile single-chip solution for industrial automation, building control, automotive telematics, and connected IoT gateways. The Cortex-M4F core delivers 150 DMIPS / 600 CoreMark performance, supported by a tightly coupled memory (TCM) interface, a Memory Protection Unit (MPU), and a single-precision FPU that accelerates floating-point math for sensor fusion, audio processing, and motor control loops. The device supports Sleep, Idle, Standby, and Backup modes with RTC retention down to a few microamps, enabling battery-friendly field deployments. Built on a low-power 65 nm CMOS process, the chip balances high performance with deterministic interrupt latency. Typical applications include industrial control HMI panels, automotive gateway ECUs, building automation controllers, USB/Ethernet-connected IoT edge nodes, smart energy metering with TLS encryption, and factory automation PLCs. The Extended Flash Performance variant is particularly suited to designs requiring 100 k cycle endurance and 20-year data retention, such as firmware update logging or OBD-II telemetry recorders. When designing with this device, allocate careful attention to the 128-pin TQFP power and decoupling network: at least one 4.7 uF bulk plus a 100 nF decoupling capacitor per VDD pin pair is recommended, and the analog AVDD rail should be filtered with a ferrite bead from the digital supply. For Ethernet applications, route the RMII traces as a 50 ohm controlled-impedance group with matched lengths to the PHY. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the standalone manufacturer datasheet or single distributor listing.

견적 요청 문의하기
ATSAME54P19A-CTUT - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip
ATSAME54P19A-CTUT

ATSAME54P19A-CTUT - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip

The Microchip Technology ATSAME54P19A-CTUT is a 32-bit ARM Cortex-M4F microcontroller with Floating Point Unit running up to 120 MHz, integrating 512 KB dual-panel Flash with ECC and 192 KB SRAM with ECC in a 120-ball TFBGA (8x8 mm) package for industrial applications. The SAM E54 family adds a 2-channel CAN-FD, USB 2.0 Full Speed with PHY, Ethernet 10/100 MAC with PHY, and a high-speed 12-bit ADC up to 1 Msps. A microcontroller (MCU) is a single-chip processor that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals including timers, communication interfaces, and ADCs. Within the embedded hierarchy, the ATSAME54P19A sits in the high-performance MCU tier, above 8-bit MCUs (such as PIC16) and below application processors, offering deterministic real-time control with M4-class DSP and FPU capabilities. It targets industrial and IoT edge applications where deterministic performance and on-chip connectivity are required. Key features of the ATSAME54P19A-CTUT include the Cortex-M4F core with FPU, 512 KB dual-panel Flash supporting live update, 192 KB SRAM, an Event System for inter-peripheral signaling without CPU involvement, a 12-bit 1 Msps SAR ADC with up to 16 channels, two I2C, two UART/USART, four SERCOM, plus the integrated HS USB, Ethernet MAC+PHY, and CAN-FD. The 120-ball TFBGA package supports compact PCB layout, while the 120 MHz clock speed enables DSP-class signal processing in real time. Technically, the SAM E54 series uses the Cortex-M4F core with single-precision floating point, DSP extensions, and a Memory Protection Unit. The dual-panel Flash architecture allows one bank to run code while the other is reprogrammed, enabling field firmware updates without downtime - critical for industrial controllers, building automation, and connected appliances. ECC on both Flash and SRAM improves reliability in electrically noisy environments. Operating voltage is 1.71 V to 3.63 V across the industrial temperature range. Typical applications include industrial control and HMI panels, CAN-FD node controllers in building automation and solar, USB device peripherals, Ethernet-connected sensors and edge gateways, and motor-control loops using the integrated PWM timers and ADC. Designers favor this part where a single-chip solution replaces an MCU + external PHY + external CAN transceiver stack. A key design consideration is power budgeting: at 120 MHz the core draws significantly more current than at lower clock speeds, so use the integrated Dynamic Frequency Scaling and the on-chip voltage regulator to balance performance and current. Decoupling must follow the datasheet reference layout; the 120-ball BGA requires the central ground balls thermally bonded to a ground plane for thermal and signal-integrity reasons. This page synthesizes distributor pricing, application-ready companion recommendations, and practical design notes not found in the standalone datasheet PDF.

견적 요청 문의하기
ATSAME54P19A-CTUT-EFP - 120MHz Cortex-M4F MCU, 512KB Flash, 120-TFBGA | Microchip
ATSAME54P19A-CTUT-EFP

ATSAME54P19A-CTUT-EFP - 120MHz Cortex-M4F MCU, 512KB Flash, 120-TFBGA | Microchip

The Microchip Technology ATSAME54P19A-CTUT-EFP is a 32-bit ARM Cortex-M4F microcontroller from the SAM E54 high-performance family, integrating a Floating Point Unit (FPU) running up to 120 MHz, with 512 KB of Flash and 192 KB of SRAM, housed in a 120-ball TFBGA (8x8 mm) package. The part ships in Tape & Reel and is qualified for Extended Flash Performance (EFP suffix), with an operating voltage range of 1.71 V to 3.63 V. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals into one IC. The SAM E54 family sits within the Cortex-M4F tier of the ARM Cortex-M hierarchy (Cortex-M0 -> Cortex-M3 -> Cortex-M4F -> Cortex-M7), and Microchip positions it between the SAM D51 and SAM E70 families. The Cortex-M4F adds single-precision floating point and DSP extensions, making it suitable for signal conditioning, motor control loops, and digital filter computation while remaining deterministic for real-time control. Key features include a 120 MHz Cortex-M4F core with FPU, 512 KB dual-panel Flash with ECC, 192 KB SRAM with ECC, a high-speed 120 MHz peripheral bus, Full-Speed USB 2.0 with integrated PHY, 10/100 Mbps Ethernet MAC, CAN-FD, and multiple SERCOM interfaces. The device also exposes a 12-bit ADC up to 1 Msps, DAC outputs, and PWMs suited to digital power conversion. The EFP suffix indicates Extended Flash Performance characteristics for industrial temperature operation. Typical applications include industrial Ethernet gateways, USB-to-UART/CAN bridges, building automation controllers, point-of-sale terminals, and motor-control front-ends. The combination of high-speed USB, CAN-FD, and Ethernet MAC on the same die eliminates external PHY/MAC chips for many industrial networking designs. The dual-panel Flash with ECC enables live firmware updates with minimal downtime. When designing with this part, allocate decoupling capacitance of at least 100 nF on every VDD pin and 4.7 µF bulk capacitance near the LDO output. The TFBGA-120 package requires 4-layer PCB with 0.8 mm pitch fanout and laser-drilled or via-in-pad escape for reliable assembly. Confirm errata DS80000764 before committing to high-volume layout. This page consolidates distributor inventory, EOL guidance from the Microchip PCN (effective December 15, 2025), drop-in alternatives from the SAM E5x family, and PCB layout notes not found in the manufacturer datasheet, helping engineers source, qualify, or replace this device with confidence.

견적 요청 문의하기
ATSAME54P20A-AF - 120MHz Cortex-M4F MCU, 1MB Flash, Ethernet | Microchip
ATSAME54P20A-AF

ATSAME54P20A-AF - 120MHz Cortex-M4F MCU, 1MB Flash, Ethernet | Microchip

The Microchip Technology ATSAME54P20A-AF is a high-performance 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with single-precision FPU, packaged in a 128-pin TQFP (14x14 mm) industrial-grade enclosure. The device integrates 1 MB of dual-panel Flash with ECC, 256 KB SRAM with ECC, and a rich connectivity suite including 10/100 Ethernet MAC, USB, and Dual CAN-FD. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a programmable set of peripherals. The SAM E54 sits in the high-performance tier of Microchip's Cortex-M4F portfolio, sharing the SAM D5x/E5x family architecture with a deterministic interrupt model, ARM TrustZone-M support, and a 12-bit 1 Msps ADC for precision analog acquisition. Key features of the ATSAME54P20A-AF include up to 120 MHz CPU clock with FPU and DSP extensions, 1 MB Flash / 256 KB SRAM with single-error-correction ECC, an integrated 10/100 Ethernet MAC with IEEE 1588 PTP support, and Dual CAN-FD controllers for high-throughput automotive/industrial networking. A high-speed USB 2.0 Full-Speed interface, a 12-bit 1 Msps ADC with up to 32 channels, and multiple SERCOM peripherals deliver flexible communication. Architecturally, the SAM E54 uses a Cortex-M4F core with tightly-coupled memory, a 4 KB instruction cache, and a multi-layer bus matrix for parallel peripheral access. The dual-panel Flash allows simultaneous read-while-write, enabling live firmware updates without halting code execution. ECC on both Flash and SRAM is critical for functional-safety applications targeting IEC 61508 or ISO 26262. Typical applications include industrial Ethernet gateways, building automation controllers, automotive body and chassis ECUs, smart energy / solar inverter control, and human-machine interface (HMI) panels with TFT displays. The combination of Ethernet + CAN-FD + USB positions this MCU as a networking hub. Design tip: bypass VDDIO/VDDIN pins with 100 nF + 4.7 uF ceramics placed within 3 mm of the package, and provide a dedicated ferrite on AVDD for the ADC to achieve full 12-bit ENOB. Trace routing for the Ethernet RMII signals should be length-matched within 50 mils. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet to support rapid component selection.

견적 요청 문의하기
ATSAME54P20A-AFT - 120MHz Cortex-M4F MCU, 1MB Flash | Microchip
ATSAME54P20A-AFT

ATSAME54P20A-AFT - 120MHz Cortex-M4F MCU, 1MB Flash | Microchip

The Microchip ATSAME54P20A-AFT is a 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with single-precision FPU, 1 MB dual-panel Flash with ECC, and 256 KB SRAM with ECC, housed in a 128-pin TQFP (14x14 mm) package. It targets connected industrial, automotive, and IoT edge applications requiring deterministic real-time control, on-chip Ethernet, USB, and CAN-FD connectivity. A 32-bit microcontroller (MCU) is a programmable system-on-chip that integrates a CPU core, memory, and peripherals into a single silicon die. ARM Cortex-M4F cores add a hardware floating-point unit and DSP extensions, positioning the SAM E54 family in the high-performance tier of the Cortex-M lineup, above Cortex-M0/M0+ and Cortex-M3 devices. Within Microchip's portfolio, the SAM E54 sits between the lower-pin SAM D5x and the higher-end SAME70 Cortex-M7 family. Key features of the ATSAME54P20A-AFT include 120 MHz CPU clock, 1 MB Flash with dual-panel ECC, 256 KB SRAM, a 10/100 Ethernet MAC with IEEE 1588 support, USB 2.0 Full-Speed with embedded PHY, two CAN-FD controllers, an I2S audio interface, a 12-bit 1 Msps ADC, and a 16-bit PWM timer/counter for motor control. The on-chip AES/SHA crypto accelerator and true random number generator enable secure connected designs. Architecturally, the SAM E54 combines an M-class core with a multi-layer bus matrix connecting Cortex-M4F, DMA, flash, SRAM, and peripherals, enabling parallel data movement and deterministic interrupt latency. The dual-panel flash bank supports in-field firmware updates without halting the CPU, which is critical for industrial gateways and remote sensor nodes. Typical applications include industrial motor control (BLDC/PMSM drives), building automation gateways, USB/Ethernet/CAN-connected sensor hubs, audio processing peripherals, and secure IoT edge nodes. The wide operating temperature range and AEC-Q100-grade qualification pathway make it suitable for harsh-environment industrial and automotive-class designs. When designing with the ATSAME54P20A-AFT, attention to PCB layout of the high-speed Ethernet and USB signals is critical - 90 ohm differential impedance, length matching, and proper ground stitching are required for EMI compliance. The internal 1.2V core regulator requires a stable 1uF X7R decoupling network within a few millimeters of the VCORE pin. This page synthesizes current distributor pricing, drop-in alternatives within the SAME54/53/51 SAM family, and practical hardware design notes not found in the standalone datasheet - giving the engineer a single integrated reference for part selection, sourcing, and PCB bring-up.

견적 요청 문의하기
ATSAME54P20A-AU-EFP - 120MHz Cortex-M4F MCU, 1MB Flash, TQFP-128
ATSAME54P20A-AU-EFP

ATSAME54P20A-AU-EFP - 120MHz Cortex-M4F MCU, 1MB Flash, TQFP-128

The Microchip Technology ATSAME54P20A-AU-EFP is a 32-bit ARM Cortex-M4F microcontroller from the SAM E54 family, integrating a 120 MHz processor core with single-precision floating-point unit, 1 MB of dual-panel Flash with ECC, and 256 KB of SRAM with ECC. It is housed in a 128-pin TQFP (14x14 mm) package rated for the industrial temperature range and is supplied in tray packaging. The "EFP" suffix designates Extended Flash Performance / extended grade variant of the SAM E54 line, and the "AU" suffix denotes the 128-TQFP package option with -40C to +85C industrial temperature grade. An ARM Cortex-M4F MCU is a microcontroller that combines the Cortex-M4 DSP-enhanced core with an IEEE 754 single-precision floating-point unit, providing hardware-accelerated math and DSP in addition to deterministic interrupt handling for real-time embedded systems. The SAM E54 sits above general-purpose Cortex-M0+ MCUs in performance and below Cortex-M7 parts, targeting industrial control, IoT gateways, HMI, and audio/voice front-end designs where deterministic latency and DSP throughput matter. Key features include the Cortex-M4F core with FPU and DSP extensions running at up to 120 MHz, 1 MB of dual-panel Flash with ECC for high-availability firmware, 256 KB SRAM with ECC, a high-speed USB 2.0 Full-Speed device/host/On-The-Go interface, 10/100 Mbps Ethernet MAC with IEEE 1588 support, CAN-FD controllers, SD/MMC host interface, and multiple SERCOM (SERial COMmunication) channels that can be configured as UART, SPI, I2C, or LIN. The part additionally provides a 12-bit ADC up to 1 Msps, DAC, analog comparators, and cryptographic accelerators for AES/SHA. The architecture uses a multi-layer AHB bus matrix connecting the CPU, SRAM, Flash, peripheral bridges, and DMAC, allowing the Cortex-M4F core to fetch from Flash with zero-wait-state performance under typical conditions and to sustain high-throughput peripheral transfers concurrently with CPU execution. The dual-panel Flash layout enables read-while-write, useful for in-field firmware updates without halting execution. Typical applications include industrial PLCs and motor controllers, building automation gateways, HMI touch panels, USB peripherals with Ethernet bridging, audio processing front-ends that benefit from the FPU, CAN-FD automotive body and chassis ECUs, and secure connected IoT nodes using the integrated crypto accelerators and TRNG. Designers should provide adequate bypass on VDDIO and VDDANA domains per the SAM E54 datasheet recommendation (typically 100 nF plus bulk capacitors), ensure the 32.768 kHz crystal load capacitance matches the chosen crystal, and reserve the SWD pins (SWDIO/SWCLK) for in-system programming. The Ethernet PHY, USB, and CAN-FD interfaces each require external transceiver ICs. This page synthesises distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
ATSAME54P20A-AUT - 120MHz Cortex-M4F MCU 1MB Flash | Microchip
ATSAME54P20A-AUT

ATSAME54P20A-AUT - 120MHz Cortex-M4F MCU 1MB Flash | Microchip

The Microchip Technology ATSAME54P20A-AUT is a high-performance 32-bit ARM Cortex-M4F microcontroller with FPU, running up to 120 MHz, featuring 1 MB of dual-panel Flash with ECC and 256 KB SRAM with ECC, in a 128-pin TQFP (14x14 mm) industrial-grade package. It targets industrial automation, automotive, and connected IoT applications requiring deterministic real-time control combined with Ethernet and CAN-FD connectivity. The -AUT suffix indicates the automotive temperature grade with extended qualification testing per Microchip's AEC-Q100 equivalent screening for industrial/automotive use. What is a Cortex-M4F microcontroller? A Cortex-M4F (Cortex-M4 with Floating-Point Unit) is an ARM processor core designed for embedded systems that need both DSP-class signal processing and IEEE 754 single-precision floating-point math. It belongs to the Cortex-M family -> 32-bit MCU hierarchy -> embedded microprocessor -> semiconductor. The 'M' variants use Thumb-2 instruction set with deterministic interrupt latency, distinguishing them from Cortex-A application cores used in Linux systems. Key features of the ATSAME54P20A-AUT include a 120 MHz CPU with single-precision FPU, 1 MB dual-panel Flash supporting live firmware update, 256 KB SRAM, plus connectivity peripherals including 10/100 Ethernet MAC, dual CAN-FD, USB 2.0 High-Speed, and SD/SDIO/eMMC host. The SAM E54 also integrates a 12-bit 1 Msps ADC, DAC, analog comparators, and SERCOM (serial communication) ports for flexible peripheral mapping. Architecturally, the SAM E54 uses Microchip's Event System for zero-latency inter-peripheral signaling, a hardware cryptographic module supporting AES/SHA/TRNG, and a Dual-Panel Flash architecture that allows one bank to be updated while code runs from the other - critical for functional safety and Over-The-Air (OTA) firmware updates. The Cortex-M4F delivers 1.25 DMIPS/MHz with DSP extensions for sensor fusion and motor control loops. Typical applications include industrial PLCs and motor drives with FOC algorithms, automotive body and gateway ECUs, building automation BACnet/Modbus nodes, IoT edge gateways with Ethernet connectivity, and consumer audio DSP products. The combination of CAN-FD + Ethernet + Cortex-M4F DSP makes the SAME54 ideal for industrial protocol bridging. When designing with this device, plan for a robust 3.3V LDO or DC-DC supply with bulk decoupling, route the Ethernet MII/RMII signals with controlled-impedance traces, and reserve the dual-panel Flash banks for A/B OTA partitioning. Use Microchip's MPLAB Harmony 3 or ASF4 frameworks and SEGGER Embedded Studio for IDE support.

견적 요청 문의하기
ATSAME54P20A-CTUT-EFP - SAM E54 MCU 120MHz 1MB Flash | Microchip
ATSAME54P20A-CTUT-EFP

ATSAME54P20A-CTUT-EFP - SAM E54 MCU 120MHz 1MB Flash | Microchip

The Microchip ATSAME54P20A-CTUT-EFP is a high-performance 32-bit ARM Cortex-M4F microcontroller with Floating Point Unit (FPU) running up to 120 MHz, integrating 1 MB dual-panel Flash with ECC and 256 KB SRAM with ECC in a 120-ball TFBGA 8x8 mm package with USB, Ethernet, and CAN interfaces. The EFP suffix denotes the Extended Flash Performance grade supplied on Tape & Reel. An ARM Cortex-M4F microcontroller is a 32-bit microcontroller core featuring a hardware Floating Point Unit that executes single-precision IEEE-754 instructions, Thumb-2 DSP extensions, and an integrated Memory Protection Unit. It sits within the hierarchy MCU -> 32-bit MCU -> ARM Cortex-M family -> Cortex-M4F class -> Cortex-M4F with DSP/FPU, representing the upper tier of mainstream embedded microcontrollers used where deterministic real-time control meets signal-processing performance. Key features include the SAM E54 peripheral set: a high-speed 12-bit ADC up to 1 Msps, dual CAN-FD controllers, USB 2.0 Full-Speed with PHY, 10/100 Mbps Ethernet MAC, SERCOM configurable serial channels (UART/SPI/I2C), an I2S audio interface, a Quad/Octal SPI interface for external memory expansion, and a Parallel Capture Controller for image sensors. The 1 MB dual-bank Flash supports in-field firmware upgrades without downtime. Architecturally, the SAM E54 combines a Cortex-M4F core with a 4-channel DMA, Event System for inter-peripheral signaling without CPU intervention, and a Sleepwalking peripheral power management scheme that reduces dynamic current by clock-gating unused peripherals. Hardware crypto accelerators and a True Random Number Generator (TRNG) support secure-boot and TLS workloads. Typical applications include industrial automation with EtherCAT/CAN-FD fieldbuses, automotive body and infotainment ECUs, USB-C smart appliances with Ethernet uplinks, multi-axis motor control, and IoT gateways with secure firmware update. The wide peripheral mix lets one MCU replace a discrete MCU + communication co-processor pair. Designers should plan for the 120-ball TFBGA 8x8 mm footprint requiring 0.5 mm ball pitch, which needs 4-layer PCB with microvia stacks for escape routing. Decoupling: 100 nF on every VDD pin pair plus 4.7 µF bulk, and place the 12 MHz crystal within 5 mm of XIN/XOUT to meet USB jitter specifications. Avoid routing Ethernet differential pairs across power-plane splits. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical BGA-routing guidance not found in the manufacturer datasheet, accelerating sourcing and PCB layout decisions for engineers evaluating the SAM E54 family.

견적 요청 문의하기
ATSAME70J19A-AN - 300MHz Cortex-M7 MCU 512KB Flash | Microchip
ATSAME70J19A-AN

ATSAME70J19A-AN - 300MHz Cortex-M7 MCU 512KB Flash | Microchip

The Microchip ATSAME70J19A-AN is a high-performance 32-bit ARM Cortex-M7 microcontroller with Floating Point Unit (FPU), operating at up to 300 MHz, and featuring 512 KB of Flash and 256 KB of SRAM in a 64-pin LQFP (10x10 mm) package. Part of the SAM E70 family, this MCU integrates a 16-bit static memory controller, HS USB with on-chip PHY, and a rich set of connectivity peripherals including CAN-FD, Ethernet, and multiple UART/SPI/I2C interfaces. The device is supported by a comprehensive Microchip ecosystem including MPLAB Harmony, Atmel Studio 7, and SEGGER Embedded Studio. What is a Cortex-M7 microcontroller? An ARM Cortex-M7 is a high-performance 32-bit microcontroller core designed for applications requiring DSP-class signal processing, complex control loops, and floating-point arithmetic. Within the broader taxonomy, the Cortex-M7 sits at the top of the Cortex-M family (above Cortex-M4/M3/M0/M0+), and the SAM E70 family sits within Microchip's portfolio of Cortex-M7-based microcontrollers, alongside the SAME70 and SAMS70 series. The Cortex-M7's superscalar pipeline, dual-issue load/store, and tightly-coupled memory enable deterministic real-time response at high clock rates. Key features of the ATSAME70J19A-AN include a 300 MHz maximum CPU clock, 16 KB instruction cache and 16 KB data cache, single-precision/double-precision hardware floating point unit (FPU), and a Memory Protection Unit (MPU). The device also provides 5x USART, 5x SPI, 4x TWI (I2C), 3x CAN-FD, 1x HS USB, 1x 10/100 Ethernet MAC, and a 12-bit ADC with up to 24 channels. Operating voltage is 1.62 V to 3.6 V, with industrial temperature grade support from -40 C to +85 C. The ATSAME70J19A-AN uses a Harvard-bus architecture with branch prediction, prefetch buffers, and tightly-coupled SRAM to minimize flash wait states at full 300 MHz operation. The peripheral DMA controller (PDC) and separate XDMAC provide high-bandwidth peripheral-to-memory transfers without CPU intervention, enabling deterministic real-time control. The integrated 16-bit SMC supports PSRAM, NOR Flash, and NAND Flash external memories, making the device suitable for systems requiring external storage. Typical applications include industrial automation controllers, building automation gateways, smart energy metering, point-of-sale (POS) terminals, medical instrumentation, and audio/voice processing systems. The HS USB with on-chip PHY, Ethernet MAC, and CAN-FD make it particularly well suited to industrial networking and IoT edge nodes requiring multiple wired connectivity interfaces. When designing with this device, allocate decoupling capacitors close to every VDD pin and provide a clean 3.3 V supply with adequate bulk capacitance. Connect the NRST line to the reset supervisor and ensure the trace to the 32.768 kHz crystal is short and guarded by ground. Use the XDMAC for high-throughput peripheral transfers to minimize CPU interrupt load. This page synthesizes distributor pricing, drop-in SAME70 family alternatives, and practical design notes not found in the standalone manufacturer datasheet PDF.

견적 요청 문의하기
ATSAME70J19A-ANT - ARM Cortex-M7 300MHz MCU 512KB Flash | Microchip
ATSAME70J19A-ANT

ATSAME70J19A-ANT - ARM Cortex-M7 300MHz MCU 512KB Flash | Microchip

The Microchip ATSAME70J19A-ANT is a 32-bit ARM Cortex-M7 microcontroller with Floating Point Unit (FPU), running up to 300 MHz, integrating 512 KB of Flash and 256 KB of SRAM in a 64-pin LQFP (10x10 mm) package supplied on Tape & Reel. It is part of the SAM E70 family and provides high-performance deterministic control for industrial, automotive, and consumer applications. The device also includes a 16-bit Analog Front End (AFE) plus extensive connectivity for system integration. What is a Cortex-M7 microcontroller? An ARM Cortex-M7 microcontroller is a high-end 32-bit MCU core designed for deterministic real-time control with rich DSP capability and a double-precision FPU. Within the hierarchy: Cortex-M7 -> ARM Cortex-M -> 32-bit MCU -> microcontroller -> semiconductor, the M7 sits at the top of the Cortex-M family, above the M4/M3, and below Cortex-A application cores. The SAM E70 line in particular targets motor control, industrial networking, and graphical HMI where DSP performance and fast interrupt response are required. Key features of the ATSAME70J19A-ANT include 300 MHz core speed with 1500 CoreMark, single-precision and double-precision FPU, 512 KB Flash, 256 KB SRAM, and a 16-bit AFE supporting up to 24-bit sigma-delta conversion. Connectivity options include HS USB with on-chip PHY, CAN-FD, Ethernet MAC, multiple UART/SPI/TWI/I2S, and a 2D graphic LCD controller. The 64-pin LQFP-64 package gives access to most peripherals while keeping the board footprint compact at 10x10 mm. The architecture pairs a Cortex-M7 core with a multi-layer AHB bus matrix, dedicated SRAM banks, and tightly-coupled memory for zero-wait-state code execution. This delivers deterministic latency for real-time control loops. Integrated peripherals include timers, PWM, Quadrature Encoder, ADC, DAC, and EMAC, allowing a single-chip solution for complex mechatronic systems. Typical applications include industrial motor control (FOC for PMSM/BLDC), solar inverters, automation PLCs, EV charging stations, audio processing, and graphical HMI panels. The 300 MHz performance plus DSP extensions also suits digital signal conditioning and predictive maintenance sensor nodes. When designing with this device, allocate decoupling close to every VDD pin and follow the SAME70 PCB layout checklist for high-speed HS USB and Ethernet lines. Use Microchip's MPLAB Harmony 3 framework and ASF for peripheral drivers; supply sequencing must respect the 1.2V core and 3.3V I/O rail relationship described in the datasheet. This page synthesizes distributor pricing for ATSAME70J19A-ANT, lists verified drop-in alternatives in the same 64-pin LQFP footprint, and consolidates practical design notes drawn from the manufacturer datasheet - an information package not available on any single distributor or manufacturer page.

견적 요청 문의하기
ATSAME70J19B-AN - 300MHz Cortex-M7 MCU, 512KB Flash, 64-LQFP
ATSAME70J19B-AN

ATSAME70J19B-AN - 300MHz Cortex-M7 MCU, 512KB Flash, 64-LQFP

The Microchip Technology ATSAME70J19B-AN is a 32-bit ARM Cortex-M7 microcontroller with Floating Point Unit (FPU) operating at up to 300MHz, integrating 512KB of Flash and 256KB of SRAM in a 64-pin LQFP (10x10 mm) package. It is part of the SAM E70 family, which is engineered for high-performance embedded applications requiring deterministic real-time control combined with rich connectivity and analog peripherals. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a heterogeneous set of peripherals such as timers, ADC/DAC, communication controllers, and GPIO. Within the broader semiconductor taxonomy, an MCU belongs to the embedded processor family (microcontroller -> microprocessor -> semiconductor device -> integrated circuit). Cortex-M7 is ARM's highest-performance microcontroller core, adding a double-precision FPU, branch prediction, and tightly-coupled memories (TCM) that enable deterministic sub-microsecond interrupt response. Key features include a single-precision hardware Floating Point Unit, 16KB of I-cache and 16KB of D-cache, 384KB of additional SRAM available for system use, a 12-bit 2 Msps Analog Front End (AFE), a 12-bit DAC, dual CAN-FD controllers, high-speed USB, Ethernet MAC, and an extended temperature operating range suited to industrial and automotive-grade environments. According to the Microchip SAM E70 datasheet, the device supports up to 300MHz CPU clock with 1.5 DMIPS/MHz and 2.14 CoreMark/MHz, providing DSP-class signal processing throughput in a deterministic microcontroller footprint. From an architectural perspective, the Cortex-M7 core is paired with a multi-layer AHB/APB bus matrix that allows simultaneous DMA and CPU accesses without contention. The SAM E70 family integrates hardware cryptographic accelerators, a true random number generator (TRNG), and secure boot support, hardening the platform against firmware tampering. The on-chip 12-bit AFE delivers up to 24 analog inputs and the 12-bit DAC supports both continuous and single-output modes, enabling closed-loop control of motors, power converters, and audio stages. Typical applications include industrial motor control and field-oriented control (FOC) drives, factory automation PLCs, building automation HVAC controllers, audio processing and high-fidelity consumer audio, medical instrumentation such as patient monitors and infusion pumps, automotive body and chassis ECUs, and IoT edge nodes with on-device analytics. The 64-LQFP package supports standard reflow soldering and is friendly to hand-prototyping and 4-layer PCB designs. When designing with this device, ensure that the firmware uses the IAR, Keil, or MPLAB X IDE toolchain with the appropriate CMSIS pack, and that decoupling is provided per the reference schematic - at minimum a 100nF X7R on every VDD pin plus a bulk 4.7uF near the regulator. The internal voltage regulator must be sequenced correctly at power-up; consult the datasheet 'Power Considerations' section to avoid in-rush latch-up. This page synthesizes verified distributor pricing, drop-in alternative listings, and practical design notes not aggregated on any single manufacturer or distributor product page, giving procurement and design engineers a single decision-grade reference for the ATSAME70J19B-AN.

견적 요청 문의하기