ATSAMDA1-XPRO vs ATSAMD21-XPRO 비교
다음의 상세 나란히 비교: ATSAMDA1-XPRO 제조: Microchip Technology 및 ATSAMD21-XPRO 제조: Microchip Technology. 주요 사양, 전기적 파라미터, 패키징, 수명 주기 상태, 가격 및 재고를 비교하여 설계 요구 사항에 가장 적합한 부품을 결정하십시오.
Microchip Technology
ATSAMDA1-XPRO - SAM DA1 Xplained Pro ARM Cortex-M0+ Eval Board
ATSAMDA1-XPRO ✓ 활성Microchip Technology
ATSAMD21-XPRO - SAM D21 Xplained Pro ARM Cortex-M0+ Eval Board
ATSAMD21-XPRO ✓ 활성사양 비교
| 파라미터 | ATSAMDA1-XPRO | ATSAMD21-XPRO |
|---|---|---|
| 브랜드 | Microchip Technology | Microchip Technology |
| 카테고리 | Development Boards | Development Boards |
| 수명 주기 상태 | 활성 | 활성 |
| 재고 상태 | In Stock | In Stock |
| 단가 (USD) | $72.00 | $36.25 |
| Product Type | Evaluation Board / Development Kit | Evaluation Board (Xplained Pro) |
| Target MCU Family | SAM DA1 (ARM Cortex-M0+) | — |
| Target Device Variants | ATSAMDA1E / ATSAMDA1G / ATSAMDA1J (32-/48-/64-pin) | — |
| Core Processor | ARM Cortex-M0+ 32-bit | ARM Cortex-M0+ 32-bit |
| Maximum Core Frequency | 48 MHz | — |
| CoreMark/MHz | 2.46 | — |
| On-chip Flash (max) | 64 KB | — |
| On-chip SRAM | 8 KB | — |
| Read-While-Write Flash | Up to 2 KB | — |
| SERCOM Modules | 6 | — |
| Peripheral Touch Controller (PTC) | Yes (hardware capacitive touch) | — |
| Integrated Debugger | Yes (EDBG / Xplained Pro on-board) | — |
| Expansion Interface | Xplained Pro / mikroBUS headers | — |
| Operating Temperature (target MCU) | -40 C to +105 C | — |
| Automotive Qualification (target MCU) | AEC-Q100 qualified | — |
| RoHS 상태 | Compliant | Compliant |
| Target MCU | — | ATSAMD21J18A |
| CPU Max Frequency | — | 48 MHz |
| Flash Memory (on-chip) | — | 256 KB |
| SRAM | — | 32 KB |
| On-board SPI Flash | — | 1 MB |
| Low-frequency Crystal | — | 32.768 kHz |
| High-frequency Crystal | — | 12 MHz |
| Debug Interface | — | nEDBG (CMSIS-DAP) on-board |
| USB Connectors | — | 1x Micro-B (debug/CDC), 1x Micro-B (target) |
| Extension Headers | — | 3x 20-pin Xplained Pro (compatible with I/O1, OLED1, QT1, PROTO1) |
| User Inputs | — | 1x mechanical reset button, 1x user touch button |
| User Outputs | — | 1x user LED |
| Arduino-compatible Headers | — | Yes (subset of ATSAMD21J18A I/O) |
| Operating Voltage (target) | — | 3.3 V |
| Board Power Source | — | USB Micro-B |
| Supported IDEs | — | MPLAB X IDE, Atmel Studio 7, Atmel START |
| Form Factor | — | Xplained Pro standard (approx 88 mm x 53 mm) |