5M80ZE64C4N - MAX V CPLD, 64 LE, 184MHz, 1.8V | Intel/Altera
부품 번호: 5M80ZE64C4N ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $3.52 | $3.52 |
| 10 | $3.17 | $31.70 |
| 100 | $2.81 | $281.00 |
| 500 | $2.46 | $1,230.00 |
| 1,000 | $2.1 | $2,100.00 |
5M80ZE64C4N 개요
What is a CPLD? A Complex Programmable Logic Device (CPLD) is a non-volatile programmable logic device that sits between simple PLDs (PALs/GALs) and FPGAs in the programmable logic hierarchy. Unlike FPGAs which use SRAM-based configuration, CPLDs use flash or EPROM-based non-volatile storage that retains the configuration at power-off, making them ideal as glue logic, I/O expander, or boot-time controller. Within the programmable logic taxonomy, MAX V belongs to the low-power, instant-on CPLD category from Intel (formerly Altera), positioned for cost-sensitive power-management sequencing, bus bridging, and I/O expansion.
Key features include 64 macro cells distributed across 4 logic array blocks (LABs), 2 global clocks, in-system programmability via JTAG (IEEE 1149.1), and on-chip flash configuration memory. The device also integrates a user flash memory block and supports hot-socketing for live insertion. The non-volatile architecture provides instant-on functionality with no external boot PROM required, simplifying board design.
From a technical depth perspective, the 5M80ZE64C4N uses the Quartus Prime design software with Verilog HDL, VHDL, or schematic entry. The device supports the IEEE 1149.1 boundary-scan test standard and integrates pull-up resistors on every I/O pin for floating-pin tolerance. The E64 package variant provides 79 usable I/O pins thanks to the exposed pad that ties to GND and the multi-VCCIO bank structure.
Typical applications include I/O expansion for microcontrollers, address decoding in microprocessor systems, power-up/power-down sequencing for FPGAs and ASICs, bus bridging between legacy and modern interfaces, and LED driving in industrial displays. When designing, plan the multi-voltage I/O banks (VCCIO1, VCCIO2, etc.) carefully to ensure interface compatibility. Designers should also reference AN 491 for power-on sequencing recommendations. This page synthesizes distributor pricing, drop-in MAX V alternatives, and practical Quartus design notes not found in the manufacturer datasheet alone.
드롭인 대체품: 5M80ZE64C4N — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: 5M80ZE64C4N (동일 폼 팩터 및 풋프린트) — 차이점: Package, Operating Temperature, Configuration Memory, Programming Interface, User Flash Memory.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
5M80ZE64C4/I5N
✅ 드롭인✓ 재고 있음
$9.75 / 개
데이터시트 보기 →5M80ZE64C4
✅ 드롭인✓ 재고 있음
$4 / 개
데이터시트 보기 →5M80ZE64A5N
✅ 드롭인✓ 재고 있음
$3.05 / 개
데이터시트 보기 →5M160ZE64C4N
✅ 드롭인✓ 재고 있음
$4.3 / 개
데이터시트 보기 →5M160ZE64C5N
✅ 드롭인✓ 재고 있음
$4.95 / 개
데이터시트 보기 →5M40ZE64C4N
✅ 드롭인✓ 재고 있음
$1.7 / 개
데이터시트 보기 →5M80ZE64C4N 최대 정격 & 전기적 특성
| Family | MAX V |
| Device Logic Elements | 64 |
| Number of Macro Cells | 64 |
| Number of Logic Array Blocks (LABs) | 4 |
| Maximum User I/O Pins | 79 |
| Maximum Operating Frequency | 184.1 MHz |
| Core Voltage (VCCINT) | 1.8 V |
| I/O Voltage (VCCIO) | 1.5V / 1.8V / 2.5V / 3.3V |
| Programmability | In-system via JTAG (IEEE 1149.1) |
| Configuration Memory | Non-volatile flash, instant-on |
| Global Clocks | 2 |
| User Flash Memory | On-chip (8 Kbits) |
| Operating Temperature Grade | Commercial (0C to +85C) |
| Speed Grade | C4 |
| 패키지 | 64-pin EQFP (E64) with exposed pad |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant (lead-free) |
| Hot Socketing | Supported |
5M80ZE64C4N 핀 구성
| 핀 1 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 2 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 3 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 4 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 5 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 6 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 7 | VCCIO1 — I/O bank 1 supply voltage |
| 핀 8 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 9 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 10 | GND — Ground reference |
| 핀 11 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 12 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 13 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 14 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 15 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 16 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 17 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 18 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 19 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 20 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 21 | VCCIO2 — I/O bank 2 supply voltage |
| 핀 22 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 23 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 24 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 25 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 26 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 27 | GND — Ground reference |
| 핀 28 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 29 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 30 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 31 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 32 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 33 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 34 | TCK — JTAG test clock input (IEEE 1149.1) |
| 핀 35 | TMS — JTAG test mode select input |
| 핀 36 | TDI — JTAG test data input |
| 핀 37 | TDO — JTAG test data output |
| 핀 38 | GND — Ground reference |
| 핀 39 | VCCINT — Core supply voltage (1.8V) |
| 핀 40 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 41 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 42 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 43 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 44 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 45 | VCCIO2 — I/O bank 2 supply voltage |
| 핀 46 | I/O — Dual-purpose user I/O pin (Bank 2) |
| 핀 47 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 48 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 49 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 50 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 51 | GND — Ground reference |
| 핀 52 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 53 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 54 | VCCIO1 — I/O bank 1 supply voltage |
| 핀 55 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 56 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 57 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 58 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 59 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 60 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 61 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 62 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 63 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 64 | I/O — Dual-purpose user I/O pin (Bank 1) |
| 핀 EP | GND (Exposed Pad) — Thermal/ground pad; must be soldered to PCB ground plane |
일반적인 애플리케이션
5M80ZE64C4N 적합 용도: 7 애플리케이션s: I/O Expansion for Microcontrollers, Power Sequencing Controller for FPGAs and ASICs, Address Decoding and Chip-Select Logic, Bus Bridging and Protocol Translation, LED Driving and Industrial Display Control, Glue Logic in Industrial Automation, FPGA Configuration Supervisor.
I/O Expansion for Microcontrollers
The 5M80ZE64C4N serves as an instant-on I/O expander for microcontrollers that lack sufficient GPIO. With 79 user I/O pins and multi-voltage VCCIO banks (1.5V to 3.3V), it adds PWM outputs, keypad scanning, or sensor multiplexing to MCUs like the STM32 or PIC. The non-volatile flash configuration means the CPLD is active at power-on before the MCU initializes, providing fail-safe initial pin states. The 184 MHz fMAX enables sub-10 ns response to interrupt-driven events. Quartus Prime Lite free toolchain enables rapid prototyping without license costs.
추천
Power Sequencing Controller for FPGAs and ASICs
The 5M80ZE64C4N is widely used as a power-up and power-down sequencing controller for multi-rail FPGAs and ASICs requiring strict rail ordering. Its non-volatile instant-on behavior activates at system power-up and asserts enable signals to DC-DC converters in a defined sequence, then holds the FPGA in reset until all rails are stable. The CPLD's 2 global clocks and configurable output slew rates reduce EMI during sequencing events. Typical designs use 4 to 16 macro cells per sequence step, well within the 5M80's 64 LE capacity.
추천
Address Decoding and Chip-Select Logic
In microprocessor and DSP systems, the 5M80ZE64C4N implements high-speed address decoding and chip-select generation across multiple peripherals. With 79 available I/O and 184 MHz operation, it can decode 24-bit or wider address buses with sub-10 ns propagation delay, replacing dozens of discrete 74-series logic gates with a single reprogrammable device. The instant-on behavior means chip-selects are valid at power-on without waiting for MCU firmware to load, critical for systems with external boot memories.
추천
Bus Bridging and Protocol Translation
The 5M80ZE64C4N bridges between legacy parallel buses (ISA, SRAM, 8/16-bit MCU) and modern serial interfaces (SPI, I2C, UART). With multi-voltage I/O banks, it can simultaneously interface 5V-tolerant legacy devices and 1.8V modern ASICs. The on-chip 8 Kbit user flash stores configuration constants and lookup tables, eliminating external EEPROMs. Typical bridging applications include legacy-to-modern display controllers, sensor hub aggregation, and factory automation protocol converters.
추천
LED Driving and Industrial Display Control
The 5M80ZE64C4N drives multiplexed LED matrices, seven-segment displays, and character LCDs in industrial HMIs. Its 79 I/O pins support up to 8-digit 7-segment displays with current-driver enable signals. The 1.8V core and 3.3V VCCIO capability drive both modern LED drivers and legacy interfaces. The non-volatile flash storage retains display patterns and animations across power cycles. With 184 MHz fMAX, the CPLD refreshes displays with no visible flicker.
추천
Glue Logic in Industrial Automation
In factory automation and PLC systems, the 5M80ZE64C4N replaces discrete 74HC and 74LVC logic gates with a single programmable device, reducing board area and BOM cost. Functions include watchdog timer generation, signal conditioning, level shifting between field-bus voltages, and custom timing logic for motor control. The commercial temperature grade and surface-mount EQFP-64 package fit standard industrial PCB assembly processes. JTAG in-system programmability allows field updates without desoldering.
추천
FPGA Configuration Supervisor
The 5M80ZE64C4N supervises FPGA configuration from a parallel flash memory, monitoring the FPGA's CONF_DONE and nSTATUS signals and recovering from configuration errors by toggling nCONFIG. This offloads critical boot-time supervision from the system MCU, ensuring reliable FPGA startup even when the host processor is reset or being updated. The CPLD's instant-on behavior guarantees the FPGA boot supervisor is operational before any other system component powers up, a critical safety function in telecom and medical equipment.
추천
추천 제품 요약
엔지니어링 참조 데이터: 5M80ZE64C4N — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | 5M80ZE64C4/I5N | 5M80ZE64C4 | 5M80ZE64A5N | 5M160ZE64C4N | 5M160ZE64C5N | 5M40ZE64C4N |
|---|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | 64-pin EQFP (E64) | 64-pin EQFP (E64) - same | 64-pin EQFP (E64) - same | 64-pin EQFP (E64) - same | 64-pin EQFP (E64) - same | 64-pin EQFP (E64) - same | 64-pin EQFP (E64) - same |
| Logic Elements (Macro Cells) | 64 | 64 | 64 | 64 | 160 (+150%) | 160 (+150%) | 40 (-37.5%) |
| Speed Grade | C4 | I5 (industrial temp, C4 speed) | C4 | A5 (automotive) | C4 | C5 (slower) | C4 |
| Operating Temperature Grade | Commercial (0C to +85C) | Industrial (-40C to +100C) | Commercial | Automotive (-40C to +125C) | Commercial | Commercial | Commercial |
| Core Voltage (VCCINT) | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Maximum User I/O | 79 | 79 | 79 | 79 | 79 (same E64 package limits) | 79 | 79 |
| Configuration Memory | Non-volatile flash | Non-volatile flash | Non-volatile flash | Non-volatile flash | Non-volatile flash | Non-volatile flash | Non-volatile flash |
주요 차별점
- Non-volatile flash configuration with instant-on (vs SRAM-based FPGAs (e.g., Cyclone IV))
- 79 user I/O pins in compact EQFP-64 package (vs 5M40ZE64C4N (same package))
- Multi-voltage VCCIO banks (1.5V/1.8V/2.5V/3.3V) (vs Single-voltage I/O CPLDs)
설계 노트
Decouple VCCINT (1.8V core) with at least one 0.1uF ceramic capacitor placed within 5 mm of the supply pin, plus a bulk 10uF tantalum or ceramic near the IC. Each VCCIO bank (VCCIO1, VCCIO2) requires its own 0.1uF decoupling cap even if both banks share the same voltage rail. The exposed pad (EP) must be soldered to a low-impedance ground plane to dissipate heat and provide electrical reference. Estimated: total decoupling requirement is approximately 3 to 5 capacitors; budget 100 nF + 10 uF per supply domain.
The EQFP-64 package has a 0.5 mm pitch and a large center exposed pad. Use microvia-in-pad PCB technology or a solder-mask-defined pad pattern to ensure reliable solder joint formation under the EP. Maximum reflow temperature per JEDEC J-STD-020 is 260C for 60 seconds peak. Maintain at least 0.2 mm keep-out between EP and inner signal traces to prevent solder wicking issues. The 0.5 mm pitch requires 4-mil trace and space design rules for fanout routing.
Pin 1 is identified by the dot marker on the top surface of the package. JTAG pins (TCK, TMS, TDI, TDO) must be routed with 4-mil traces kept short and away from switching signals to avoid programming errors. Both global clock inputs (CLK0, CLK1) should use matched-length routing if used for source-synchronous applications. The GND pins at positions 10, 27, 38, 51 form the recommended stitching pattern; connect each directly to the ground plane with short vias.
Do not leave unused I/O pins floating - enable the internal weak pull-up resistors in the Quartus Prime device configuration, or tie them externally to a valid logic level. The 5M80ZE64C4N does not support LVDS or HSTL I/O standards; only LVCMOS/LVTTL at 1.5V/1.8V/2.5V/3.3V are supported. The flash programming cycles are rated for at least 100 write/erase cycles - design the firmware update path to track and limit the number of field reprogramming events.
For outputs switching at 100 MHz or above, place a 33 ohm series damping resistor near the CPLD pin to reduce transmission-line ringing on traces longer than 25 mm. Enable slew-rate control (slow slew rate) in the Quartus Prime assignment editor for switching outputs to reduce EMI by approximately 6 to 10 dB at the cost of a small propagation delay increase. Estimated: 33 ohm damping reduces overshoot by approximately 50% on 50 mm microstrip traces.
규정 준수 정보
RoHS and lead-free compliant per Intel/Altera product page. Not AEC-Q100 qualified in this commercial speed grade - choose 5M80ZE64A5N variant for automotive applications.
