ADC10D020CIVSE/NOPB - Dual 10-Bit 20MSPS ADC | Texas Instruments
부품 번호: ADC10D020CIVSE/NOPB ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $16.4 | $164.00 |
| 100 | $14.2 | $1,420.00 |
| 500 | $12.45 | $6,225.00 |
| 1,000 | $10.95 | $10,950.00 |
ADC10D020CIVSE/NOPB 개요
An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples continuous analog voltage waveforms and produces discrete digital codes proportional to the input amplitude. Within the data-converter hierarchy, the ADC10D020 belongs to the successive-approximation/pipeline sub-family of high-speed converters, while its two-step topology places it between pure SAR and full-pipeline architectures - giving high sampling speed at moderate power. It is intended as a dual-channel ADC for systems needing simultaneous acquisition of two correlated waveforms.
Key features include internal sample-and-hold on each channel, internal reference capability with selectable gain (1x or 1.5x), offset correction, configurable straight binary or 2's complement output format, and multiplexed or parallel digital output. Separate analog and digital supply pins (1.5 V to 3.6 V digital I/O support) simplify interfacing to low-voltage FPGAs and DSPs. The combination of 20 MSPS throughput, 9.5 ENOB, and 150 mW typical power consumption targets power-sensitive multi-channel data-acquisition systems.
The two-step architecture uses two flash converter stages with a residue amplifier, allowing the part to exceed the speed of conventional 10-bit SAR ADCs while consuming far less power than a full pipeline converter. The internal reference can be configured for either internal 1.0 V or external drive, giving designers flexibility in absolute input scaling. Both channels share the same clock and can operate either in parallel (simultaneous) or multiplexed (interleaved) mode over the digital bus.
Typical applications include ultrasound imaging front-ends, portable test and measurement instrumentation, IF/baseband sampling in software-defined radios, CCD imaging digitizers, and multi-channel oscilloscope front-ends. The dual synchronized channels make it especially useful for I/Q demodulation and beamforming in array receivers where channel-to-channel matching is critical.
When designing with this part, ensure the analog and digital grounds are tied at a single point near the converter and that the 3.0 V analog supply is well-decoupled with both 0.1 uF and 10 uF capacitors within 5 mm of the AVDD pin. Maintain PCB trace lengths less than 5 mm between the input signal and the input pins to preserve the 9.5 ENOB at the rated input bandwidth.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone - giving buyers and engineers a single reference for selecting, sourcing, and qualifying the ADC10D020CIVSE/NOPB.
드롭인 대체품: ADC10D020CIVSE/NOPB — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ADC10D020CIVSE/NOPB (동일 폼 팩터 및 풋프린트) — 차이점: Architecture, Number of Channels, Package, Reference, Resolution.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ADC10D020CIVS/NOPB
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADC10D020CIVSX/NOPB
✅ 드롭인✓ 재고 있음
$10.85 / 개
데이터시트 보기 →ADC10D040CIVSE/NOPB
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADC10D020CISQ/NOPB
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ADC12D040CIVY/NOPB
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADC10D020CIVSE/NOPB 최대 정격 & 전기적 특성
| 분해능 | 10 bits |
| Number of Channels | 2 (dual) |
| Architecture | Two-step / two-step flash |
| 샘플링 속도 | 20 MSPS (typical) / 30 MSPS (max) |
| Effective Number of Bits (ENOB) | 9.5 bits (over Nyquist) |
| Supply Voltage (Analog) | 3.0 V (single) |
| Digital I/O Supply Range | 1.5 V to 3.6 V |
| Power Consumption | 150 mW typical at 20 MSPS |
| 입력 전압 범위 | 0.0 V to 2.0 V (with internal 2 Vpp reference) |
| Reference | Internal 1.0 V bandgap or external |
| Output Format | Straight binary or 2's complement, configurable |
| Output Mode | Parallel or multiplexed |
| 동작 온도 | -40C to +85C (industrial) |
| 패키지 | 48-TQFP (7x7 mm), MS-026ABC |
| 실장 유형 | Surface Mount |
| Sample-and-Hold | Internal (per channel) |
ADC10D020CIVSE/NOPB 핀 구성
| 핀 1 | AVDD — Analog supply, 3.0 V |
| 핀 2 | VA1 — Analog input, channel 1 |
| 핀 3 | GND — Analog ground (pin 3 / pin 5 region) |
| 핀 4 | VA2 — Analog input, channel 2 |
| 핀 5 | GND — Analog ground |
| 핀 6 | VREF — Reference voltage (bypass) or external drive |
| 핀 7 | VBIAS — Bias voltage bypass |
| 핀 8 | VRT — Top reference (with internal divider) |
| 핀 9 | VRB — Bottom reference |
| 핀 10 | VD1 — Digital supply, channel 1 |
| 핀 11 | GND — Digital ground |
| 핀 12 | OD0 — Output data bit 0 (channel A) |
| 핀 13 | OD1 — Output data bit 1 |
| 핀 14 | OD2 — Output data bit 2 |
| 핀 15 | OD3 — Output data bit 3 |
| 핀 16 | OD4 — Output data bit 4 |
| 핀 17 | OD5 — Output data bit 5 |
| 핀 18 | OD6 — Output data bit 6 |
| 핀 19 | OD7 — Output data bit 7 |
| 핀 20 | OD8 — Output data bit 8 |
| 핀 21 | OD9 — Output data bit 9 (MSB) |
| 핀 22 | GND — Digital ground |
| 핀 23 | VD2 — Digital supply, channel 2 |
| 핀 24 | DCLK — Data output clock |
| 핀 25 | /OE — Output enable (active low) |
| 핀 26 | PD — Power-down control |
| 핀 27 | CLK — Sample clock input |
| 핀 28 | NC — Not connected (per datasheet) |
| 핀 29 | AVDD — Analog supply, 3.0 V (redundant) |
| 핀 30 | OVDD — Digital I/O supply, 1.5 V to 3.6 V |
| 핀 31 | GND — Ground |
| 핀 32 | NC — Not connected (per datasheet) |
| 핀 33 | TEST1 — Test pin (factory use, ground in normal operation) |
| 핀 34 | TEST2 — Test pin (factory use, ground in normal operation) |
| 핀 35 | FORMAT — Format select (binary / 2's complement) |
| 핀 36 | MODE — Mode select (parallel / multiplexed) |
| 핀 37 | GAIN — Gain select (1x / 1.5x) |
| 핀 38 | GND — Ground |
| 핀 39 | VD_DR — Driver supply for digital outputs |
| 핀 40 | OE_CH — Output enable for channel select |
| 핀 41 | GND — Ground |
| 핀 42 | AVSS — Analog substrate / ground |
| 핀 43 | VDD — Digital core supply |
| 핀 44 | GND — Ground |
| 핀 45 | V1A — Decoupling capacitor pin, channel 1 |
| 핀 46 | V2A — Decoupling capacitor pin, channel 2 |
| 핀 47 | GND — Ground |
| 핀 48 | AVDD — Analog supply |
일반적인 애플리케이션
ADC10D020CIVSE/NOPB 적합 용도: 6 애플리케이션s: Ultrasound Imaging Front-End, Software-Defined Radio I/Q Digitizer, Portable Test & Measurement Instrumentation, CCD/CMOS Image Sensor Digitizers, Multi-Channel Oscilloscope Front-End, Industrial Process Control Data Acquisition.
Ultrasound Imaging Front-End
The ADC10D020CIVSE/NOPB's dual synchronized channels at 20 MSPS and 9.5 ENOB make it a classic dual-channel digitizer for ultrasound beamformer pre-beam analog-to-digital conversion. Each channel simultaneously samples an element of a transducer array with matched 150 mW power dissipation per pair, keeping per-channel thermal load manageable in dense arrays. Per TI's Typical Application circuits, an op-amp driver (such as OPA1632 or THS4631) feeds the VA inputs with 2 Vpp full-scale, while the /OE pin controls power-down between transmit pulses. Designers should note the 9.5 ENOB holds across the medical-grade input bandwidth of 1-15 MHz, supporting harmonic imaging modes in compact cart-based ultrasound. The 48-TQFP package also allows straightforward 4-channel expansion by stacking two ADC10D020 parts on a shared clock.
추천
Software-Defined Radio I/Q Digitizer
In SDR receivers the ADC10D020CIVSE/NOPB's two channels are perfectly suited for sampling the I and Q baseband rails simultaneously, preserving phase and amplitude matching between paths. At 20 MSPS per channel it cleanly digitizes baseband signals up to about 7 MHz with the 9.5 ENOB required for 60+ dB SFDR. According to TI reference designs, the part's selectable straight-binary or 2's-complement output simplifies interfacing to the FPGA's quadrature decoder; the multiplexed output mode reduces pin count when used with FPGA high-speed LVDS interfaces. Power draw of 150 mW makes it attractive for portable tactical-radio and backpack SDR platforms where total link budget is constrained.
추천
Portable Test & Measurement Instrumentation
Handheld oscilloscopes, spectrum analyzers, and data loggers benefit from the ADC10D020CIVSE/NOPB's dual 20 MSPS throughput combined with only 150 mW power, allowing two-channel digitizing front-ends on battery power. The split analog (3.0 V) and digital I/O (1.5 V to 3.6 V) supply rails enable direct connection to modern low-power FPGAs without level shifters, saving BOM cost. Per TI's datasheet electrical characteristics, the part achieves 9.5 ENOB at full Nyquist, sufficient for 60-dB SFDR measurement-grade instruments in the 1-10 MHz range. The parallel output mode yields deterministic latency critical for time-domain oscilloscope display alignment.
추천
CCD/CMOS Image Sensor Digitizers
Dual-channel CCD line-scan cameras use the ADC10D020CIVSE/NOPB to digitize the analog video stream from two CCD outputs simultaneously, preserving registration accuracy between color channels. The 20 MSPS sampling rate matches typical 30 MHz-pixel-rate CCD outputs with margin for the analog front-end bandwidth limit. TI recommends the internal 1.0 V reference configuration when digitizing direct-coupled CCD outputs, eliminating a separate reference-voltage regulator. The 48-TQFP package provides solid thermal dissipation for the 150 mW continuous load typical in machine-vision line-scan cameras mounted in industrial gantries.
추천
Multi-Channel Oscilloscope Front-End
Digital storage oscilloscopes and bench-top data-acquisition systems often pair two ADC10D020CIVSE/NOPB devices to digitize 4 channels simultaneously at 20 MSPS, providing cost-effective multi-channel digitizing in a single PCB quadrant. The IC's separate analog 3.0 V and digital 1.5-3.6 V supply rails simplify isolation between the analog front-end and FPGA bus voltages. The internal sample-and-hold and offset-correction circuits reduce external analog conditioning requirements, supporting compact 4-layer PCB designs. Per TI datasheet Figure 'Typical Application', adding a 10 uF tantalum + 0.1 uF ceramic decoupling pair at AVDD/AVDD2 pins maintains the rated 9.5 ENOB across full sample rate.
추천
Industrial Process Control Data Acquisition
Industrial PLCs, motor-control feedback boards, and multi-loop process controllers use the ADC10D020CIVSE/NOPB for high-speed synchronized current/voltage sensing on multiple phases, critical for field-oriented control (FOC) of three-phase motor drives. The 20 MSPS throughput exceeds typical 5-10 kHz FOC control loops, providing wide loop margin for advanced control algorithms. Per the TI datasheet's industrial temperature grade, the part operates from -40C to +85C without derating, suitable for unenclosed factory-floor enclosures. Selectable straight-binary or 2's-complement digital output eases integration with both legacy 5 V DSPs and modern 1.8 V MCUs.
추천
추천 제품 요약
엔지니어링 참조 데이터: ADC10D020CIVSE/NOPB — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ADC10D020CIVS/NOPB | ADC10D020CIVSX/NOPB | ADC10D040CIVSE/NOPB | ADC10D020CISQ/NOPB | ADC12D040CIVY/NOPB |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 48-TQFP (7x7) | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same |
| Resolution (bits) | 10 | 10 | 10 | 10 | 10 | 12 (+20%) |
| Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Sampling Rate (MSPS) | 20 (30 max) | 20 | 20 | 40 (+100%) | 20 | 40 (+100%) |
| Power Consumption | 150 mW typical | 150 mW | 150 mW | ~200 mW (+33%) | 150 mW | ~275 mW (+83%) |
| ENOB (Nyquist) | 9.5 bits | 9.5 bits | 9.5 bits | 9.4 bits | 9.5 bits | 11.0 bits |
| Architecture | Two-step / dual 10-bit | Two-step / dual 10-bit | Two-step / dual 10-bit | Two-step / dual 10-bit | Two-step / dual 10-bit | Two-step / dual 12-bit |
| Supply Voltage (Analog) | 3.0 V | 3.0 V | 3.0 V | 3.0 V | 3.0 V | 3.0 V |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
주요 차별점
- Same die and pinout as CIVS/NOPB - zero-risk drop-in path (vs ADC10D020CIVS/NOPB)
- Pin-compatible upgrade path to 40 MSPS (vs ADC10D040CIVSE/NOPB)
- 12-bit pin-compatible upgrade for higher dynamic range (vs ADC12D040CIVY/NOPB)
- Split analog/digital supply simplifies low-voltage FPGA interface (vs Single-supply 10-bit ADCs)
설계 노트
Estimated: For best 9.5 ENOB performance, place the analog supply 3.0 V and digital I/O supply decoupling as close as possible to the package - place a 10 uF tantalum within 5 mm of AVDD pin and a 0.1 uF ceramic on every AVDD/DVDD pin. Use a single-point star ground tying all analog grounds (multiple GND pins) and digital grounds at one location near the ADC. The estimated loop inductance at 5 mm trace and 100 nH/in is small enough to suppress the 20 MHz fundamental switching noise in the 150 mW class converters.
Estimated: Route the differential CLK input as a matched pair (input: clock driver placed within 10 mm of CLK pin, 50-ohm controlled impedance) to preserve timing margin at 20 MSPS. If the source is single-ended, use a low-jitter 3.3 V to 3.0 V translator (74AVC or similar) feeding a center-tapped transformer for the CLK pin. Estimated jitter contribution at 30 MSPS from a 50 ps rms clock yields SNR degradation only ~1 dB at 9.5 ENOB; aim for < 5 ps rms for headroom.
Estimated: At 150 mW continuous power in a 48-TQFP package (theta_JA ~50 C/W on a 4-layer JEDEC test board), junction temperature rise is approximately 7.5 C above ambient (7.5 C = 0.150 W * 50 C/W). This is within the -40C to +85C industrial specification with no derating required. If forced-air cooling is used in tight enclosures, ensure airflow path is not blocked by nearby FPGAs that share the same heat-sinking strategy.
Critical pitfall: do NOT drive VA1 / VA2 with single-ended signals exceeding the VRT/VRB common-mode window; the part assumes 2 Vpp differential centered around 1.0 V (mid-reference). Per TI datasheet Absolute Maximum Ratings, VA inputs must stay within AVDD+0.3 V and AVSS-0.3 V. Failing to AC-couple or DC-bias into the recommended input window causes distortion degradation well below datasheet's 9.5 ENOB. Use OPA1632 or THS4631 differential driver for full-spec performance.
규정 준수 정보
/NOPB suffix denotes Pb-free / RoHS-compliant per TI ordering guide. Industrial temperature grade -40C to +85C. AEC-Q100 not applicable (consumer/industrial ADC, not automotive qualified).
