ADS7824PG4 - 4-Ch 12-Bit 40kSPS SAR ADC | Texas Instruments
부품 번호: ADS7824PG4 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $16.8 | $168.00 |
| 100 | $14.2 | $1,420.00 |
| 500 | $12.6 | $6,300.00 |
| 1,000 | $11.1 | $11,100.00 |
ADS7824PG4 개요
A successive-approximation register ADC is a comparator-based converter that performs a binary search against the input voltage, one bit per clock cycle, producing a complete 12-bit result in a fixed number of conversion cycles. Within the broader data-converter taxonomy, the ADS7824PG4 sits between precision delta-sigma converters (which trade speed for resolution) and high-speed flash converters (which trade resolution and power for sample rate). SAR ADCs are favored where single-shot deterministic latency, modest resolution, and low power consumption must coexist, as in multiplexed industrial sensor acquisition.
Key features include a guaranteed 25 us max acquisition-and-conversion time, 50 mW max power dissipation from a single +5 V supply, ±10 V industrial input range with on-chip laser-trimmed scaling resistors, ±0.5 LSB linearity, ±0.1% channel-to-channel matching, and a 4-channel single-ended or pseudo-differential input mux. The internal 2.5 V reference and clock eliminate the need for external analog support components in most designs.
Typical applications include industrial process-control PLCs, multi-loop data acquisition systems, multi-channel instrumentation front-ends, and pin-compatible upgrades for legacy ADS7825 16-bit designs. The wide ±10 V input range allows direct connection to industrial ±10 V transducers and 4-20 mA loop sense resistors without external signal conditioning.
드롭인 대체품: ADS7824PG4 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ADS7824PG4 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Data Interface, Sampling Rate, Number of Input Channels, Input Type.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ADS7824P
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADS7825P
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADS7807PBG4
✅ 드롭인✓ 재고 있음
$11.85 / 개
데이터시트 보기 →ADS7824PG4 최대 정격 & 전기적 특성
| 분해능 | 12 bits |
| Number of Channels | 4 (single-ended / pseudo-differential) |
| 샘플링 속도 | 40 kSPS |
| Conversion Time | 25 us max |
| Architecture | SAR (Successive Approximation) |
| 입력 전압 범위 | ±10 V (industrial, on-chip scaled) |
| Channel-to-Channel Matching | ±0.1% |
| Linearity (INL) | ±0.5 LSB max |
| 공급 전압 | +5 V single supply |
| Power Dissipation | 50 mW max |
| Data Interface | Parallel + Serial |
| Reference | Internal 2.5 V |
| 동작 온도 범위 | -40C to +85C |
| 패키지 | 28-pin PDIP (N) 0.300 inch, through-hole |
| Lead-Free / RoHS | Yes (G4 suffix, Pb-free) |
ADS7824PG4 핀 구성
| 핀 1 | CH0 — Analog input channel 0 |
| 핀 2 | CH1 — Analog input channel 1 |
| 핀 3 | CH2 — Analog input channel 2 |
| 핀 4 | CH3 — Analog input channel 3 |
| 핀 5 | AGND — Analog ground |
| 핀 6 | REF — Internal 2.5 V reference output / bypass |
| 핀 7 | DGND — Digital ground |
| 핀 8 | VCC — +5 V analog/digital supply |
| 핀 9 | R/C — Read/Convert input |
| 핀 10 | CS — Chip select (active low) |
| 핀 11 | BUSY — Conversion in progress (active high) |
| 핀 12 | HBEN — High-byte enable for parallel read |
| 핀 13 | DB11/MSB — Data bit 11 / MSB |
| 핀 14 | DB10 — Data bit 10 |
| 핀 15 | DB9 — Data bit 9 |
| 핀 16 | DB8 — Data bit 8 |
| 핀 17 | DB7 — Data bit 7 |
| 핀 18 | DB6 — Data bit 6 |
| 핀 19 | DB5 — Data bit 5 |
| 핀 20 | DB4 — Data bit 4 |
| 핀 21 | DB3 — Data bit 3 |
| 핀 22 | DB2 — Data bit 2 |
| 핀 23 | DB1 — Data bit 1 |
| 핀 24 | DB0/LSB — Data bit 0 / LSB |
| 핀 25 | SDAT — Serial data output |
| 핀 26 | SCLK — Serial clock input |
| 핀 27 | SYNC — Synchronization input |
| 핀 28 | DGND — Digital ground |
일반적인 애플리케이션
ADS7824PG4 적합 용도: 6 애플리케이션s: Industrial Process Control PLCs, Multi-Channel Data Acquisition Systems, 4-20 mA Current Loop Monitoring, Multi-Channel Instrumentation Front-Ends, Pin-Compatible Legacy ADS7825 Upgrades, SCADA Remote Terminal Units (RTUs).
Industrial Process Control PLCs
The ADS7824PG4's 4-channel multiplexed inputs and ±10 V industrial input range make it ideally suited for programmable logic controller analog input modules. With on-chip laser-trimmed scaling resistors accepting ±10 V directly, it eliminates the need for external signal-conditioning op-amps for transducer signals such as pressure, flow, and level sensors. The 25 us conversion time and 40 kSPS sampling rate comfortably exceed the typical update rates of <100 Hz in industrial loops, while the 50 mW power dissipation allows the module to operate from a single +5 V PLC backplane rail. Multiple channels share one converter, reducing BOM cost and board area for compact PLC designs.
추천
Multi-Channel Data Acquisition Systems
For multi-channel data acquisition boards serving 4-32 channels, the ADS7824PG4 offers a compact front-end via its built-in 4-channel mux and parallel/serial interface. The internal 2.5 V reference and clock reduce external component count, while ±0.1% channel-to-channel matching allows uniform measurement without per-channel calibration. Eight ADS7824PG4 devices can share a serial bus to expand to 32 channels without address-decoding logic, supporting applications such as multi-zone temperature monitoring, distributed strain gauge arrays, and laboratory instrumentation front-ends with deterministic single-shot 25 us conversion time.
추천
4-20 mA Current Loop Monitoring
The ADS7824PG4's 4-channel input mux and ±10 V input range directly accommodate 4-20 mA current loops when terminated with a 250 ohm sense resistor, producing a 1-5 V signal that falls well within the ADC's input span. Each of the four channels can monitor an independent loop, and the 25 us conversion time means an entire 4-channel scan completes in approximately 100 us, far faster than the <1 Hz loop update requirement. The ±0.5 LSB integral nonlinearity ensures accurate process variable digitization, while the internal reference eliminates long-term calibration drift typical of ratiometric measurement chains.
추천
Multi-Channel Instrumentation Front-Ends
Portable test and measurement instruments that read multiple sensors simultaneously benefit from the ADS7824PG4's 4-channel mux and parallel/serial dual interface. The -40C to +85C industrial temperature range supports laboratory and field-deployed use, while ±0.5 LSB linearity preserves measurement fidelity for strain gauges, thermocouple amplifiers (post-cold-junction compensation), and bridge sensors. Internal scaling to ±10 V allows the same board to handle both low-level and industrial signal levels, simplifying the analog front-end and reducing component count.
추천
Pin-Compatible Legacy ADS7825 Upgrades
The ADS7824PG4 is explicitly pin-compatible with the ADS7825 family (per TI datasheet footnote referencing 16-bit converters in the ADS family), allowing designers to drop the ADS7824PG4 onto existing ADS7825 16-bit layouts when cost or power budget is prioritized over resolution. The same scaling, multiplexer, and digital interface are preserved, so firmware updates are unnecessary. This makes the ADS7824PG4 attractive for cost-reduced variants of established industrial products where 12-bit resolution is provably sufficient.
추천
SCADA Remote Terminal Units (RTUs)
SCADA remote terminal units operating in unmanned field enclosures value the ADS7824PG4's robustness through its industrial temperature grade and ±10 V input tolerance for protection against field transients. The 4-channel mux lets a single ADC service temperature, pressure, level, and flow transmitters in an RTU, with the ±0.1% channel-to-channel matching ensuring consistent conversion across transmitters of the same type. Power dissipation at 50 mW max also helps passive cooling in sealed enclosures where convection is limited, supporting long-life field deployment.
추천
추천 제품 요약
엔지니어링 참조 데이터: ADS7824PG4 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ADS7824P | ADS7824U | ADS7825P | ADS7825U | ADS7807PBG4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-PDIP (N) through-hole | 28-PDIP (N) through-hole - same | 28-SOIC (DW) - different | 28-PDIP (N) - same | 28-SOIC (DW) - different | 28-PDIP (N) - same |
| Resolution | 12 bits | 12 bits | 12 bits | 16 bits | 16 bits | 16 bits |
| Number of Channels | 4 | 4 | 4 | 4 | 4 | 1 |
| Sampling Rate | 40 kSPS | 40 kSPS | 40 kSPS | 40 kSPS | 40 kSPS | 40 kSPS |
| Input Voltage Range | +/-10 V | +/-10 V | +/-10 V | +/-10 V | +/-10 V | +/-10 V |
| Conversion Time | 25 us max | 25 us max | 25 us max | 25 us max | 25 us max | 25 us max |
| Pb-Free (G4 suffix) | Yes | No (standard marking) | No | No | No | Yes |
| Approx. Unit Price (qty 1) | $18.50 | $18.00 | $17.20 | $22.00 | $21.00 | $19.80 |
주요 차별점
- Pin-compatible 16-bit upgrade path (vs ADS7825P)
- Integrated 4-channel input multiplexer (vs ADS7807PBG4 (single-channel 16-bit))
- Pb-free G4 suffix for lead-free compliance (vs ADS7824P (non-G4))
- Dual parallel and serial interfaces (vs ADS7822PG4 (serial-only))
설계 노트
The ADS7824PG4 operates from a single +5 V supply with 50 mW max power dissipation. Decouple VCC to DGND with a 10 uF tantalum + 0.1 uF ceramic bypass placed close to the supply pin. For high-noise industrial environments, add a ferrite bead between the +5 V rail and the IC VCC pin. The internal 2.5 V reference output (REF) should be buffered with a 10 uF external capacitor; do not load the REF pin with more than a few hundred microamps or reference accuracy degrades. Estimated: typical quiescent current is ~10 mA at +5 V, well within the 50 mW max envelope.
On a 28-PDIP board, dedicate one plane layer to AGND (pins 5 and 28 ground connection point) and another to DGND, joining them at a single point near the +5 V regulator ground return. Keep analog input traces (CH0-CH3, AGND) routed away from digital control signals (CS, R/C, BUSY, SCLK) to avoid clock feedthrough into the sample-and-hold. Place the REF bypass capacitor directly across pin 6 (REF) and pin 5 (AGND); trace length should be less than 5 mm to minimize reference noise pickup.
Common pitfalls include (1) forgetting to convert SDAT during a parallel mode read, which can cause bus contention - the datasheet recommends tying SDAT to a defined logic level if unused; (2) drawing more than ~500 uA from the internal REF pin causes INL degradation across all four channels; (3) cycling CS faster than the conversion time, which forces BUSY to ignore the read and produce stale data; and (4) using the ADS7824PG4 outside its -40C to +85C temperature range, which compromises ±0.5 LSB linearity. Per the datasheet, latching HBEN with the wrong polarity during a parallel read can latch the high byte into the low byte bus, scrambling the conversion result.
규정 준수 정보
G4 suffix denotes Pb-free, RoHS-compliant lead finish. AEC-Q100 not applicable for industrial data acquisition. Halogen-free marking not explicitly stated in verified data.
