ATMEGA16A-MUR - 8-Bit AVR MCU 16KB Flash 16MHz | Microchip
부품 번호: ATMEGA16A-MUR ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $4.12 | $4.12 |
| 10 | $3.71 | $37.10 |
| 100 | $3.3 | $330.00 |
| 500 | $2.97 | $1,485.00 |
| 1,000 | $2.64 | $2,640.00 |
ATMEGA16A-MUR 개요
An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, program memory, data memory, and peripherals such as timers, serial interfaces, and analog-to-digital converters on one die. Within the semiconductor taxonomy, the ATmega16A sits under 8-bit MCU -> microcontroller -> embedded processor -> integrated circuit, and it is the AVR-family workhorse for cost-sensitive control tasks where deterministic single-cycle execution matters more than raw clock speed.
Key differentiators include 131 powerful instructions with most executing in a single clock cycle, 16 MIPS throughput at 16 MHz, and a fully static core that can be clocked down to DC for low-power operation. The 8-channel 10-bit successive-approximation ADC, two USARTs, SPI, and TWI (I2C) interfaces cover the majority of embedded control and sensor-interface requirements without external glue logic.
The ATmega16A is fabricated in a low-power CMOS process and is a functionally identical, drop-in replacement for the original ATmega16, per Microchip application note AVR522. The VQFN-44 (7x7 mm) package with exposed pad provides a compact footprint for space-constrained designs while retaining the full 32 I/O lines of the TQFP-44 variant.
Typical applications include industrial control panels, motor and relay drivers, battery chargers, sensor hubs, and legacy embedded systems that require long-term availability. The wide 2.7 V to 5.5 V supply range allows direct operation from 3.3 V or 5 V rails, and the on-chip JTAG interface supports in-system programming and debugging without a dedicated programmer.
When designing with the ATMEGA16A-MUR, decouple every VCC pin with a 100 nF ceramic capacitor placed within a few millimeters of the pin, and connect the exposed pad to a solid ground plane for thermal and noise performance. The internal calibrated RC oscillator allows operation without an external crystal, but an external 16 MHz crystal is recommended when precise UART baud rates or tight timing are required.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for selection, replacement, and layout decisions.
드롭인 대체품: ATMEGA16A-MUR — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATMEGA16A-MUR (동일 폼 팩터 및 풋프린트) — 차이점: Debug Interface, Package, EEPROM, RoHS Status, SRAM.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ATMEGA16A-MU
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ATMEGA32A-MNR
✅ 드롭인✓ 재고 있음
$3.75 / 개
데이터시트 보기 →ATMEGA16A-MUR 최대 정격 & 전기적 특성
| Core Architecture | 8-bit AVR RISC |
| Program Memory Size | 16 KB (8K x 16) Flash |
| SRAM | 1 KB |
| EEPROM | 512 B |
| Maximum CPU Speed | 16 MHz |
| Throughput | Up to 16 MIPS at 16 MHz |
| Operating Voltage | 2.7 V to 5.5 V |
| Instruction Set | 131 powerful instructions, most single-clock cycle |
| General Purpose I/O | 32 lines |
| ADC | 8-channel 10-bit successive approximation |
| Serial Interfaces | 2x USART, SPI, TWI (I2C) |
| Timers | 2x 8-bit, 1x 16-bit |
| Debug Interface | JTAG (IEEE 1149.1) |
| 패키지 | 44-pin VQFN (7x7 mm) with exposed pad |
| 실장 유형 | Surface Mount |
| 동작 온도 | -40 C to +85 C |
| RoHS 상태 | Compliant |
ATMEGA16A-MUR 핀 구성
| 핀 1 | PB0 — Port B bit 0 / T0 / XCK0 |
| 핀 2 | PB1 — Port B bit 1 / T1 / CLKO |
| 핀 3 | PB2 — Port B bit 2 / INT2 / AIN0 |
| 핀 4 | PB3 — Port B bit 3 / AIN1 / OC0 |
| 핀 5 | PB4 — Port B bit 4 / SS |
| 핀 6 | PB5 — Port B bit 5 / MOSI |
| 핀 7 | PB6 — Port B bit 6 / MISO |
| 핀 8 | PB7 — Port B bit 7 / SCK |
| 핀 9 | RESET — Reset input (active low) |
| 핀 10 | VCC — Digital supply voltage |
| 핀 11 | GND — Ground |
| 핀 12 | XTAL2 — Crystal oscillator output |
| 핀 13 | XTAL1 — Crystal oscillator input |
| 핀 14 | PD0 — Port D bit 0 / RXD |
| 핀 15 | PD1 — Port D bit 1 / TXD |
| 핀 16 | PD2 — Port D bit 2 / INT0 |
| 핀 17 | PD3 — Port D bit 3 / INT1 |
| 핀 18 | PD4 — Port D bit 4 / OC1B |
| 핀 19 | PD5 — Port D bit 5 / OC1A |
| 핀 20 | PD6 — Port D bit 6 / ICP1 |
| 핀 21 | PD7 — Port D bit 7 / OC2 |
| 핀 22 | PC0 — Port C bit 0 / ADC0 |
| 핀 23 | PC1 — Port C bit 1 / ADC1 |
| 핀 24 | PC2 — Port C bit 2 / ADC2 |
| 핀 25 | PC3 — Port C bit 3 / ADC3 |
| 핀 26 | PC4 — Port C bit 4 / ADC4 |
| 핀 27 | PC5 — Port C bit 5 / ADC5 |
| 핀 28 | PC6 — Port C bit 6 / ADC6 |
| 핀 29 | PC7 — Port C bit 7 / ADC7 |
| 핀 30 | AVCC — Analog supply voltage for ADC |
| 핀 31 | GND — Ground |
| 핀 32 | AREF — Analog reference voltage for ADC |
| 핀 33 | PA7 — Port A bit 7 / ADC7 |
| 핀 34 | PA6 — Port A bit 6 / ADC6 |
| 핀 35 | PA5 — Port A bit 5 / ADC5 |
| 핀 36 | PA4 — Port A bit 4 / ADC4 |
| 핀 37 | PA3 — Port A bit 3 / ADC3 |
| 핀 38 | PA2 — Port A bit 2 / ADC2 |
| 핀 39 | PA1 — Port A bit 1 / ADC1 |
| 핀 40 | PA0 — Port A bit 0 / ADC0 |
| 핀 41 | VCC — Digital supply voltage |
| 핀 42 | GND — Ground |
| 핀 43 | GND — Ground |
| 핀 44 | GND — Ground / exposed pad connection |
일반적인 애플리케이션
ATMEGA16A-MUR 적합 용도: 6 애플리케이션s: Industrial Control Panels, Motor and Relay Drivers, Battery Chargers and Power Management, Sensor Hubs and Data Loggers, Legacy Embedded System Maintenance, Consumer Appliance Control.
Industrial Control Panels
The ATMEGA16A-MUR fits industrial control panels because its 32 general-purpose I/O lines and 2.7 V to 5.5 V supply range interface directly with 5 V relays, optocouplers, and 24 V field wiring through simple level-shift stages. Its 16 KB Flash holds ladder-logic-equivalent control firmware, while the 8-channel 10-bit ADC samples potentiometers, thermistors, and 4-20 mA loops without external converters. The -40 C to +85 C rating covers most factory-floor environments. In a typical panel, the MCU scans inputs every 1 ms, updates outputs, and communicates status over one of the two USARTs to an HMI or PLC. The trade-off versus a 32-bit ARM Cortex-M0 is lower math throughput, but the AVR core's deterministic single-cycle execution and 5 V tolerance simplify noise-immune industrial I/O design.
추천
Motor and Relay Drivers
The ATMEGA16A-MUR drives motors and relays using its 16-bit Timer/Counter with PWM output, which generates variable-duty waveforms for H-bridge and MOSFET gate drivers at up to 16 MHz. The 32 I/O lines can directly control relay coils through ULN2003 Darlington arrays or logic-level MOSFETs, while the 10-bit ADC monitors motor current via shunt resistors for stall detection. Two USARTs allow simultaneous communication with a host controller and a diagnostic interface. Because the AVR core executes most instructions in one clock cycle, PWM update latency is predictable, which matters for closed-loop speed control. The main design consideration is that inductive loads require flyback diodes and RC snubbers to protect the MCU pins; the VQFN exposed pad should be soldered to a ground plane to dissipate the additional switching-related heat.
추천
Battery Chargers and Power Management
The ATMEGA16A-MUR suits battery charger designs because its 10-bit ADC measures battery voltage and charge current, while PWM outputs regulate charging current through a buck or linear pass stage. The 2.7 V to 5.5 V supply allows the MCU to run directly from a regulated 3.3 V rail derived from the charger input, and the 512 B EEPROM stores charge profiles and cycle counters across power loss. Two USARTs support SMBus-like or proprietary communication with battery packs. In a typical implementation, the MCU samples voltage and current every 100 ms, adjusts PWM duty to follow a CC/CV profile, and terminates charge on dV/dt or temperature rise. The trade-off versus a dedicated charger IC is higher firmware complexity, but the ATmega16A offers flexibility for multi-chemistry and custom safety algorithms.
추천
Sensor Hubs and Data Loggers
The ATMEGA16A-MUR works as a sensor hub because its 8-channel 10-bit ADC and TWI (I2C) interface connect directly to analog sensors and digital sensor ICs such as temperature, pressure, and accelerometer devices. The 1 KB SRAM buffers samples, and the 512 B EEPROM stores calibration coefficients and logging intervals. With 16 KB Flash, the MCU can run filtering, linearization, and threshold logic locally, reducing data traffic to a host. A typical data logger samples eight channels at 1 kHz, applies a moving-average filter, and streams results over USART at 115200 baud. The main limitation is SRAM size: for high-rate multi-channel logging, external SPI SRAM or FRAM may be required. The VQFN-44 package's small 7x7 mm footprint helps in compact sensor nodes.
추천
Legacy Embedded System Maintenance
The ATMEGA16A-MUR is widely used to maintain legacy embedded systems because Microchip application note AVR522 confirms it is a functionally identical, drop-in replacement for the original ATmega16. Systems designed in the 2000s around the ATmega16 can be kept in production by substituting the ATmega16A without firmware changes, since the instruction set, peripheral register map, and pinout are preserved. The 44-pin VQFN package matches the original ATmega16 VQFN footprint, so existing PCBs need no redesign. This makes the part valuable for industrial equipment with 10-20 year service lives, where redesign cost exceeds the price premium of continued AVR supply. The main caveat is that some electrical characteristics differ from the original ATmega16, so timing-critical loops should be re-validated against the ATmega16A datasheet.
추천
Consumer Appliance Control
The ATMEGA16A-MUR is used in consumer appliance control because its 32 I/O lines drive buttons, LEDs, triacs, and seven-segment displays directly, and its 10-bit ADC reads thermistors and touch-sense electrodes. The 2.7 V to 5.5 V range supports both 3.3 V and 5 V appliance rails, and the internal calibrated RC oscillator eliminates the crystal in cost-sensitive designs. In a washing machine or coffee maker, the MCU runs a state machine that sequences valves, heaters, and motors while monitoring temperature and door switches. The 16 KB Flash is sufficient for user-interface menus and safety interlocks. The trade-off versus a dedicated appliance MCU is the absence of integrated high-voltage drivers, so external triacs and relays are still required. The VQFN package's exposed pad aids thermal management in sealed enclosures.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATMEGA16A-MUR — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATMEGA16A-MU | ATMEGA32A-MNR | ATMEGA16A-AU | ATMEGA168PA-MU |
|---|---|---|---|---|---|
| Package | VQFN-44 (7x7 mm) | VQFN-44 (7x7 mm) - same | VQFN-44 (7x7 mm) - same | TQFP-44 - different | VQFN-32 - different |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 16 KB | 16 KB | 32 KB | 16 KB | 16 KB |
| SRAM | 1 KB | 1 KB | 2 KB | 1 KB | 1 KB |
| EEPROM | 512 B | 512 B | 1 KB | 512 B | 512 B |
| Maximum Clock | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 20 MHz |
| Operating Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 1.8 V to 5.5 V |
| GPIO Count | 32 | 32 | 32 | 32 | 23 |
| ADC Channels | 8-channel 10-bit | 8-channel 10-bit | 8-channel 10-bit | 8-channel 10-bit | 8-channel 10-bit |
| Packaging | Tape & Reel | Tray | Tape & Reel | Tray | Tray |
주요 차별점
- Full 32 I/O lines in a 7x7 mm package (vs ATMEGA168PA-MU)
- Pin-compatible memory upgrade path (vs ATMEGA32A-MNR)
- Documented drop-in replacement for original ATmega16 (vs ATMEGA16A-AU)
- Wide 2.7 V to 5.5 V supply with full 16 MHz operation (vs ATMEGA168PA-MU)
설계 노트
Decouple every VCC pin (pins 10 and 41) with a 100 nF ceramic capacitor placed within a few millimeters of the pin, and add a 10 uF bulk capacitor near the regulator output. Connect AVCC (pin 30) through a separate 10 uH inductor or ferrite bead from the digital VCC rail, with its own 100 nF capacitor, to isolate ADC noise. AREF (pin 32) should be bypassed with 100 nF to ground when using the internal reference. Estimated: at 16 MHz and 5 V, the ATmega16A core draws roughly 10-15 mA, so a 100 mA LDO is sufficient for the MCU alone; add margin for I/O and peripheral loads.
The VQFN-44 exposed pad (pin 44) must be soldered to a solid ground plane with a minimum of nine thermal vias (0.3 mm drill) to conduct heat away from the die. Use a stencil aperture of 60-70% of the pad area to control solder volume and avoid bridging. Keep the crystal and its two load capacitors within 10 mm of XTAL1/XTAL2 (pins 13/12) and guard them with a ground pour. Route the JTAG signals (TCK, TMS, TDI, TDO) as short, matched traces to the programming header to avoid debug failures.
Do not leave the RESET pin (pin 9) floating; add a 10 kOhm pull-up to VCC and a 100 nF capacitor to ground for reliable power-on reset. When migrating from the original ATmega16 to the ATmega16A, re-validate timing-critical code because Microchip application note AVR522 states that some electrical characteristics differ between the two devices even though they are functionally identical. Also verify fuse settings after programming: an incorrect CKSEL fuse can leave the device running from the internal RC oscillator instead of the external crystal, causing UART baud-rate errors.
규정 준수 정보
The ATMEGA16A-MUR is listed as RoHS compliant and green by distributor data. AEC-Q100 automotive qualification is not indicated for this part; automotive-grade AVR variants must be selected separately. Halogen-free status is not stated in the verified data.
