ATMEGA649-16AI - 8-Bit AVR MCU 16MHz 64KB Flash | Microchip
부품 번호: ATMEGA649-16AI ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
ATMEGA649-16AI 개요
An 8-bit AVR microcontroller is a Harvard-architecture RISC processor that executes most instructions in a single clock cycle, sitting at the low end of the embedded processing hierarchy below 32-bit MCUs but above dedicated logic. Microcontrollers of this class combine CPU, program memory, data memory, and peripherals in a single chip, serving as the central control element of an embedded system.
Key features include 130 powerful instructions with most executing in a single clock cycle, self-programming Flash with read-while-write capability for boot-loader applications, JTAG for on-chip debugging and boundary scan, and an on-chip LCD driver that offloads segment driving from software. The 54 general-purpose I/O lines available in the TQFP-64 package provide extensive connectivity to keypads, displays, and sensors.
Technically, the device belongs to the AVR ATmega family with 32 general-purpose working registers directly connected to the ALU, enabling single-cycle execution and code efficiency up to six times faster than conventional CISC MCUs. In-System Programming (ISP) allows firmware updates on the assembled board through SPI, while In-Circuit Serial Programming and debugging are supported via tools such as the MPLAB SNAP connected through an 8-pin SIL header.
Typical applications include consumer appliances with LCD user interfaces, metering products, industrial control panels, and battery-powered instruments, where the integrated LCD controller and low-power AVR core reduce board area and power consumption compared with a discrete LCD driver.
Design consideration: the LCD controller multiplexes a number of segment pins with general-purpose I/O, so pin budgeting must be completed early in the schematic capture process to avoid redesign.
This page synthesizes distributor pricing leads, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, as of 2026-09-18.
드롭인 대체품: ATMEGA649-16AI — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATMEGA649-16AI (동일 폼 팩터 및 풋프린트) — 차이점: Operating Temperature, Maximum Clock Frequency, Package, EEPROM, General Purpose I/O.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ATMEGA645-16AI
✅ 드롭인✓ 재고 있음
$6.45 / 개
데이터시트 보기 →ATMEGA645V-8AI
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →ATMEGA329-16AI
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →ATMEGA325-16AI
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ATMEGA325V-8AI
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$3.2 / 개
데이터시트 보기 →ATMEGA649-16AI 최대 정격 & 전기적 특성
| Core | AVR 8-Bit RISC |
| Core Size | 8-Bit |
| 최대 클록 주파수 | 16 MHz |
| Program Memory Size | 64 KB (32K x 16) Flash, ISP, read-while-write |
| EEPROM Size | 2 KB |
| SRAM Size | 4 KB |
| Instruction Set | 130 powerful instructions, most single-cycle |
| General Purpose I/O | 54 I/O lines (TQFP-64 configuration) |
| Working Registers | 32 x 8-bit general purpose |
| JTAG | Yes (on-chip debug and boundary scan) |
| LCD Controller | On-chip segment LCD driver |
| 패키지 | 64-TQFP (14x14 mm) |
| 실장 유형 | Surface Mount |
| 동작 온도 | -40C to +85C (industrial grade, per Atmel part number suffix 'I') |
| RoHS 상태 | Compliant (per Microchip product listing) |
| Programming Interfaces | ISP (SPI), JTAG, ICSP via MPLAB SNAP |
ATMEGA649-16AI 64-tqfp (14x14 mm) 핀 구성 가이드
ATMEGA649-16AI(64-tqfp (14x14 mm) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: ATMEGA649-16AI.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ATMEGA649-16AI 적합 용도: 6 애플리케이션s: Utility Metering with LCD Display, Consumer Appliance Control Panels, Industrial Control and HMI Nodes, Battery-Powered Portable Instruments, Building Automation and Access Control, Medical and Diagnostic Device UI Boards.
Utility Metering with LCD Display
Electricity, water, and gas meters require a low-power controller that can drive a numeric or bar-graph LCD for decades on battery or shunt-derived power. The ATMEGA649-16AI fits this role because its integrated segment LCD controller drives the display directly, eliminating a discrete LCD driver IC, while the AVR core at 16MHz handles measurement and communication tasks with mostly single-cycle instructions. Firmware can reside in the 64KB self-programming Flash with read-while-write support, enabling field firmware updates through a boot loader without interrupting the display. The 2KB EEPROM stores calibration and consumption totals across power loss. With 54 general-purpose I/O lines in the TQFP-64 package, tariff buttons, pulse outputs, and serial communication all fit on one chip.
추천
Consumer Appliance Control Panels
Ovens, washing machines, and climate-control appliances combine an LCD or segment display, a keypad matrix, and relay or triac actuation. The ATMEGA649-16AI addresses all three needs on one die: the on-chip LCD driver renders the user interface, the 16MHz AVR core with 130 single-cycle instructions executes the control state machine and safety interlocks deterministically, and the 54 I/O lines drive keypads and relays directly. The 4KB SRAM holds the UI state and task buffers, while the 2KB EEPROM retains user settings across power cycles. In-System Programming through SPI allows the same assembled PCB to be flashed with model-specific firmware at end-of-line, reducing the number of unique boards a manufacturer must stock and test.
추천
Industrial Control and HMI Nodes
Small industrial controllers and human-machine interface nodes need reliable firmware update paths, debugging infrastructure, and robust I/O. The ATMEGA649-16AI provides JTAG for on-chip debugging and boundary-scan testing of the assembled board, which shortens bring-up time and supports production test. The self-programming Flash with read-while-write capability allows a boot loader to receive new firmware over RS-485 or CAN while the application continues running, critical for equipment that cannot be powered down. The industrial temperature grade of -40C to +85C covers control-cabinet environments, and the 64KB Flash provides headroom for protocol stacks. The MPLAB SNAP tool connects via an 8-pin SIL header using two I/O pins plus reset for ICSP.
추천
Battery-Powered Portable Instruments
Handheld measurement and diagnostic instruments combine an LCD, buttons, and sensors, and must maximize runtime per charge. The ATMEGA649-16AI suits this class because the AVR core offers high code density and the LCD is driven by the low-power on-chip controller rather than software bit-banging, reducing average current. The device supports low-power sleep modes between measurements, and the 4KB SRAM buffers acquisition data without external memory. With the V-grade family members (ATMEGA325V-8AI, ATMEGA645V-8AI) sharing the same footprint, a design can be optimized for a lower supply voltage and 8MHz clock on the same PCB, trading processing speed for reduced active current in battery-critical variants.
추천
Building Automation and Access Control
Room controllers, thermostats, and access-control readers require a display, keypad, actuator driving, and persistent configuration storage. The ATMEGA649-16AI consolidates these requirements: the segment LCD controller drives the user display, the 54 GPIO lines handle keypad scanning and relay or lock actuation, and the 2KB EEPROM stores device addresses, credentials, and setpoints across power interruption. The 64KB self-programming Flash permits firmware and configuration updates in the field, an important serviceability feature for installed building equipment. The industrial -40C to +85C rating accommodates rooftop and unconditioned spaces. Firmware development is supported by the mature AVR toolchain and MegaCore open-source support for the ATmega649 device.
추천
Medical and Diagnostic Device UI Boards
Bench-top and portable medical devices such as blood-pressure monitors, glucose analyzers, and test instruments need a deterministic 8-bit control core driving a simple LCD interface, with auditable firmware. The ATMEGA649-16AI provides the on-chip LCD driver, 16MHz single-cycle-execution RISC core, and 4KB SRAM required for signal-chain coordination and display updates in a single TQFP-64 device, reducing component count on boards that must pass design reviews. JTAG enables boundary-scan production test and on-chip debugging during verification, supporting documentation-heavy development processes. The 2KB EEPROM retains calibration constants, and read-while-write Flash supports authenticated field updates. Longevity of the mature ATmega family simplifies long-term supply planning required in medical procurement.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATMEGA649-16AI — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATMEGA645-16AI | ATMEGA645V-8AI | ATMEGA329-16AI | ATMEGA325-16AI |
|---|---|---|---|---|---|
| Package | 64-TQFP (14x14 mm) | 64-TQFP (14x14 mm) - same | 64-TQFP (14x14 mm) - same | 64-TQFP (14x14 mm) - same | 64-TQFP (14x14 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core / Max Clock | AVR 8-bit / 16 MHz | AVR 8-bit / 16 MHz | AVR 8-bit / 8 MHz | AVR 8-bit / 16 MHz | AVR 8-bit / 16 MHz |
| Flash | 64 KB (32K x 16) | 64 KB | 64 KB | 32 KB | 32 KB |
| SRAM | 4 KB | 4 KB | 4 KB | 2 KB | 2 KB |
| EEPROM | 2 KB | 2 KB | 2 KB | 1 KB | 1 KB |
| LCD Controller | Yes (on-chip segment driver) | Yes | Yes | Yes | Yes |
| Temperature Grade | -40C to +85C (industrial) | -40C to +85C (industrial) | -40C to +85C (industrial) | -40C to +85C (industrial) | -40C to +85C (industrial) |
주요 차별점
- Integrated segment LCD controller (vs ATMEGA64-16AU)
- Double the memory of the 32KB pin-compatible siblings (vs ATMEGA329-16AI)
- 16MHz full-speed grade over V-class variants (vs ATMEGA645V-8AI)
설계 노트
Reserve the SPI pins and RESET on a standard 8-pin SIL programming header as documented by Microchip for the MPLAB SNAP: the connector uses two device I/O pins plus the reset line to implement in-circuit debugging and ICSP. Adding series resistors on the SPI lines lets peripherals share these pins during normal operation without interfering with programming. Place the header at the board edge for fixture access in end-of-line flashing, since the self-programming Flash allows model-specific firmware to be loaded after assembly.
The LCD segment and common pins are multiplexed with general-purpose I/O among the 54 I/O lines in the TQFP-64 package. Before schematic freeze, build a pin-budget table assigning every LCD segment, keypad row/column, and communication pin, because enabling the LCD controller removes those pins from GPIO service. Also confirm which family member you are compiling for: ATmega325/329 devices have half the Flash, SRAM, and EEPROM of the ATmega649, and firmware that fits on a 649 with margin may overflow a pin-compatible 329 during a shortage substitution.
The -16 suffix denotes a 16MHz maximum clock and the standard voltage class; the V-class family members (e.g., ATMEGA645V-8AI) run at lower supply voltages but only 8MHz. If your design targets battery operation at reduced voltage, evaluate the same-footprint V-grade parts early, since the swap is pin-compatible and reduces active current. Decouple VCC and AVCC separately with 100nF ceramics at each supply pin pair and keep the LCD drive voltage rail clean, as LCD contrast depends on a stable bias.
규정 준수 정보
RoHS compliance and lead-free status per Microchip product listing and distributor data. REACH, halogen-free, and conflict-minerals status not stated in the provided data.
