ATSAMD21G16L-MUT - 32-bit Cortex-M0+ MCU, 64KB Flash, 48MHz | Microchip
부품 번호: ATSAMD21G16L-MUT ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $4.1 | $4.10 |
| 10 | $3.68 | $36.80 |
| 100 | $3.22 | $322.00 |
| 500 | $2.86 | $1,430.00 |
| 1,000 | $2.55 | $2,550.00 |
ATSAMD21G16L-MUT 개요
A microcontroller (MCU) is an integrated circuit that combines a CPU core, program and data memory, peripherals, and I/O on a single chip. The ARM Cortex-M0+ is the smallest and most energy-efficient ARM core, designed for embedded applications that need deterministic real-time behavior at low power. Within Microchip's portfolio, the ATSAMD21G16L belongs to the SAM D family of Cortex-M0+ devices, which sit below the Cortex-M4 SAM E/SAM4S families and above the tinyAVR/AVR XMEGA families in terms of performance and feature integration.
Key features of the ATSAMD21G16L-MUT include: up to 48 MHz core clock, 64 KB Flash (64K x 8), 8 KB SRAM, Direct Memory Access (DMA) controller, full-speed USB 2.0 device, up to 6 SERCOM (serial communication) interfaces, a 12-bit ADC, a 10-bit DAC, and multiple timer/counter and PWM channels. The 48-QFN package includes an exposed thermal pad that improves heat dissipation and provides a low-impedance ground connection, which is critical at the higher CPU frequencies.
Architecturally, the SAM D21G L-variant combines a single-cycle hardware multiplier, single-cycle I/O port access, and a low-power SleepWalking peripheral event system. Compared with the older ATSAMD21G16A/B variants, the L revision changes pinout to add additional analog and timer channels per Microchip application note AT04470, so the L is not a drop-in for A/B silicon.
Typical applications include consumer electronics, IoT sensor nodes, USB human-interface devices, low-power wireless sensor hubs, lighting controllers, and industrial control with Functional Safety (FuSa) considerations. The combination of USB device, DMA, and rich peripherals makes it a strong fit for connected products on tight power budgets.
When designing with this MCU, route the exposed pad (EP) to a continuous ground plane for thermal and electrical performance, and follow Microchip's SAM D21 hardware design checklist for decoupling. The L-variant pinout is not compatible with A/B variants, so PCB layout cannot be reused directly from ATSAMD21G16A/B reference designs.
This page synthesizes verified distributor pricing, same-brand drop-in alternatives from the SAM D20/SAM D21 family, and practical design notes not found on a single manufacturer page.
드롭인 대체품: ATSAMD21G16L-MUT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATSAMD21G16L-MUT (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Operating Temperature, USB, Package, Debug Interface.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ATSAMD21G16B-MUT
✅ 드롭인✓ 재고 있음
$2.05 / 개
데이터시트 보기 →ATSAMD21G15B-MUT
✅ 드롭인✓ 재고 있음
$1.78 / 개
데이터시트 보기 →ATSAMD21E18A-MF
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$6.95 / 개
데이터시트 보기 →ATSAMD20G16A-MUT
✅ 드롭인✓ 재고 있음
$2.41 / 개
데이터시트 보기 →ATSAMD20G18A-MU
✅ 드롭인✓ 재고 있음
$3.51 / 개
데이터시트 보기 →ATSAMD21G16L-MUT 최대 정격 & 전기적 특성
| Core Architecture | ARM Cortex-M0+ |
| Family | SAM D21G (Functional Safety / FuSa) |
| Silicon Variant | L revision |
| Maximum CPU Frequency | 48 MHz |
| Program Flash | 64 KB (64K x 8) |
| SRAM | 8 KB |
| Supply Voltage Range | 1.6 V to 3.6 V |
| 동작 온도 | -40 C to +85 C |
| 패키지 | 48-pin QFN (7x7 mm) with exposed pad |
| 실장 유형 | Surface Mount (Tape & Reel, 'MUT' suffix) |
| DMA Controller | Yes |
| USB | Full-Speed USB 2.0 Device |
| ADC / DAC | 12-bit ADC / 10-bit DAC |
| Communication Interfaces | Up to 6 SERCOM (I2C/SPI/UART) |
| RoHS 상태 | Compliant (GREEN per Mouser listing) |
ATSAMD21G16L-MUT 핀 구성
| 핀 1 | VDDIO — Digital I/O supply voltage |
| 핀 2 | GND — Ground (digital) |
| 핀 3 | PA00 — GPIO / TCC2 channel 0 / ADC AIN0 reference |
| 핀 4 | PA01 — GPIO / TCC2 channel 1 / ADC AIN1 |
| 핀 5 | PA02 — GPIO / ADC AIN2 / DAC VOUT |
| 핀 6 | PA03 — GPIO / ADC AIN3 / reference voltage |
| 핀 7 | GND — Ground |
| 핀 8 | VDDANA — Analog supply voltage |
| 핀 9 | PA04 — GPIO / ADC AIN4 / SERCOM alt |
| 핀 10 | PA05 — GPIO / ADC AIN5 / SERCOM alt |
| 핀 11 | PA06 — GPIO / ADC AIN6 / SERCOM alt |
| 핀 12 | PA07 — GPIO / ADC AIN7 / SERCOM alt |
| 핀 13 | PA08 — GPIO / NMI / SERCOM alt |
| 핀 14 | PA09 — GPIO / SERCOM alt |
| 핀 15 | PA10 — GPIO / SERCOM alt |
| 핀 16 | PA11 — GPIO / SERCOM alt |
| 핀 17 | VDDCORE — Internal core voltage (decoupling only) |
| 핀 18 | GND — Ground |
| 핀 19 | PA12 — GPIO / SERCOM alt |
| 핀 20 | PA13 — GPIO / SERCOM alt |
| 핀 21 | PA14 — GPIO / SERCOM alt |
| 핀 22 | PA15 — GPIO / SERCOM alt |
| 핀 23 | PA16 — GPIO / SERCOM alt |
| 핀 24 | PA17 — GPIO / SERCOM alt |
| 핀 25 | PA18 — GPIO / SERCOM alt |
| 핀 26 | PA19 — GPIO / SERCOM alt |
| 핀 27 | PA20 — GPIO / SERCOM alt |
| 핀 28 | PA21 — GPIO / SERCOM alt |
| 핀 29 | PA22 — GPIO / SERCOM alt |
| 핀 30 | PA23 — GPIO / USB D- (alt) |
| 핀 31 | PA24 — GPIO / USB D+ (alt) |
| 핀 32 | PA25 — GPIO / SERCOM alt |
| 핀 33 | GND — Ground |
| 핀 34 | VDDIO — Digital I/O supply |
| 핀 35 | PA26 — GPIO / SERCOM alt |
| 핀 36 | PA27 — GPIO / SERCOM alt |
| 핀 37 | PA28 — GPIO / SERCOM alt |
| 핀 38 | PA29 — GPIO / SERCOM alt |
| 핀 39 | PA30 — GPIO / SWCLK (programming) |
| 핀 40 | PA31 — GPIO / SWDIO (programming) |
| 핀 41 | PB00 — GPIO / SERCOM alt |
| 핀 42 | PB01 — GPIO / SERCOM alt |
| 핀 43 | PB02 — GPIO / SERCOM alt |
| 핀 44 | PB03 — GPIO / SERCOM alt |
| 핀 45 | PB04 — GPIO / SERCOM alt |
| 핀 46 | PB05 — GPIO / SERCOM alt |
| 핀 47 | PB06 — GPIO / SERCOM alt |
| 핀 48 | PB07 — GPIO / SERCOM alt |
| 핀 49 | EP — Exposed pad - thermal/ground; must be soldered to ground plane |
일반적인 애플리케이션
ATSAMD21G16L-MUT 적합 용도: 6 애플리케이션s: USB Human Interface Device (HID), Low-Power IoT Sensor Node, Industrial Lighting Controller, Motor Control / BLDC Commutation, Consumer Wearable / Fitness Device, Industrial Control with Functional Safety (FuSa).
USB Human Interface Device (HID)
The ATSAMD21G16L-MUT's integrated full-speed USB 2.0 device peripheral with on-chip transceiver makes it ideal for USB HID designs such as keyboards, mice, game controllers, and custom input devices. The 48 MHz Cortex-M0+ core delivers deterministic USB polling, and the 8 KB SRAM comfortably holds USB descriptors plus HID report buffers. The DMA controller offloads endpoint transfers so the CPU stays free for debouncing and HID report synthesis. At 3.3 V supply the device draws under 15 mA on the USB bus, comfortably inside the USB 2.0 unconfigured-device limit. Use 10 nF + 1 uF decoupling on VDDIO and route D+/D- as a 90 ohm differential pair per USB 2.0 spec.
추천
Low-Power IoT Sensor Node
The ATSAMD21G16L-MUT's SleepWalking peripherals and event system let it stay in deep sleep while an RTC or ADC autonomously wakes the core only on relevant events, which is ideal for battery-powered IoT sensor nodes (temperature, humidity, air-quality). At 1.6 V minimum supply, the part runs directly from a single alkaline or Li-SOCl2 cell with no extra LDO. The 12-bit ADC and 10-bit DAC enable direct sensor interfacing, while the SERCOM ports map to I2C/SPI sensors. With DMA plus 8 KB SRAM, multi-sensor data buffering is possible without CPU intervention. Per Microchip SAM D21 datasheet, standby current is in the microamp range when SleepWalking is enabled.
추천
Industrial Lighting Controller
The ATSAMD21G16L-MUT's high-resolution PWM channels and 12-bit ADC make it well suited to industrial lighting controllers including DALI, DMX512, and 0-10 V dimming bridges. The 48 MHz Cortex-M0+ executes the DALI state machine with cycle-accurate timing while the DMA-driven SERCOM ports handle DMX-512 reception at 250 kbaud. Functional Safety (FuSa) capability on the SAM D21G family supports diagnostic coverage for safety-related lighting such as emergency luminaires. The 1.6-3.6 V supply tolerates industrial 24 V rails when paired with a wide-input switching regulator. Use the exposed pad for thermal relief when driving multiple high-current FET outputs.
추천
Motor Control / BLDC Commutation
The ATSAMD21G16L-MUT's TCC (Timer/Counter for Control) peripherals deliver complementary PWM with dead-time insertion, perfect for sensorless or Hall-sensor BLDC and stepper motor control at low to medium power. The Cortex-M0+ at 48 MHz is sufficient for field-oriented control (FOC) loops at modest PWM frequencies, and the 12-bit ADC samples phase currents synchronously to the PWM center. 8 KB SRAM is enough for sensorless observer state variables plus a UART telemetry buffer. The wide 1.6-3.6 V supply allows direct operation from a 3.3 V LDO downstream of a higher-voltage bus. PCB layout should isolate analog AVSS from digital GND per Microchip hardware design guidelines.
추천
Consumer Wearable / Fitness Device
The ATSAMD21G16L-MUT's low-power modes, small 48-QFN (7x7) package, and integrated USB for charging/ data make it a strong fit for consumer wearables and fitness bands. The 12-bit ADC reads heart-rate / SpO2 photodiode signals, the DAC drives LED bias, and SERCOM ports talk to BLE modules over UART. SleepWalking on the ADC and RTC lets the device idle in deep sleep between sensor samples, extending coin-cell life. The exposed thermal pad aids heat spreading when USB is plugged in for charging. At 48 MHz the Cortex-M0+ runs display drivers and BLE command stacks comfortably.
추천
Industrial Control with Functional Safety (FuSa)
Because the ATSAMD21G16L-MUT belongs to Microchip's SAM D21G Functional Safety (FuSa) family, it is designed to support safety-related industrial control loops such as sensor monitoring, actuator interlocks, and safe-shutdown subsystems. The Cortex-M0+ core, dual brown-out detectors, watchdog timer, and ECC on Flash enable diagnostic coverage required by IEC 61508 SIL-2 type designs. The 48-QFN exposed pad improves thermal performance in enclosed industrial enclosures. The 1.6-3.6 V supply tolerates 24 V industrial rails when preceded by a wide-input DC-DC converter. Reference Microchip's SAM D21G FuSa safety manual for diagnostic library usage.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATSAMD21G16L-MUT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATSAMD21G16B-MUT | ATSAMD21G15B-MUT | ATSAMD21E18A-MF | ATSAMD20G16A-MUT | ATSAMD20G18A-MU |
|---|---|---|---|---|---|---|
| Package | 48-QFN (7x7) | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 32-QFN (5x5) - smaller | 48-QFN (7x7) - same | 48-QFN (7x7) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Maximum Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash | 64 KB | 64 KB | 32 KB | 256 KB | 64 KB | 256 KB |
| SRAM | 8 KB | 8 KB | 4 KB | 32 KB | 8 KB | 32 KB |
| USB | Full-Speed USB 2.0 Device | Full-Speed USB 2.0 Device | Full-Speed USB 2.0 Device | Full-Speed USB 2.0 Device | No USB | No USB |
| Functional Safety (FuSa) | Yes (SAM D21G) | No (B variant) | No (B variant) | No (E variant) | No | No |
| Pinout Variant | L variant | A/B variant (NOT drop-in for L) | A/B variant (NOT drop-in for L) | A variant (different pin count) | SAM D20 pinout | SAM D20 pinout |
주요 차별점
- Functional Safety (FuSa) capable silicon in a Cortex-M0+ 48-QFN (vs ATSAMD21G16B-MUT)
- Integrated USB 2.0 full-speed device peripheral (vs ATSAMD20G16A-MUT)
- L-variant pinout adds analog and timer channels vs A/B variants (vs ATSAMD21G16B-MUT)
설계 노트
Estimated: the SAM D21 48-QFN package has a thermal pad (EP) that MUST be soldered to a continuous ground plane for electrical and thermal performance. Use an array of thermal vias (0.3 mm drill, 0.5 mm pitch recommended) under the EP to reduce thermal impedance from junction to ambient. Per Microchip SAM D21 hardware design checklist, missing or poorly soldered EP pads can raise die temperature by 15-20 C at typical loads. Place 100 nF decoupling on every VDD pin and a single 4.7 uF bulk capacitor within 5 mm of the package.
The ATSAMD21G16L (L variant) is NOT pin-compatible with the ATSAMD21G16A or ATSAMD21G16B silicon revisions. Microchip application note AT04470 explicitly lists pin differences between A/B and L variants. Attempting to swap an A/B layout for an L part (or vice versa) without pin reassignment will cause immediate peripheral failures (wrong ADC channels, missing USB D+/D-). Engineers porting between A/B and L silicon must re-verify every GPIO and peripheral mapping in the datasheet pinout table.
The ATSAMD21G16L operates from a single 1.6 V to 3.6 V rail. For USB bus-powered designs, connect VBUS through a regulator (3.3 V LDO) to VDDIO/VDDANA; do not power the MCU directly from VBUS because VBUS can spike above 5 V during hot-plug events. Use the SAM D21's brown-out detector (BOD) configured at 1.6 V minimum for safe reset behavior. For battery applications, leverage the SleepWalking peripheral event system to keep average current in the microamp range between sensor events.
규정 준수 정보
RoHS GREEN status confirmed via Mouser product listing ('GREEN,1.6-3.6V,48MHz'). AEC-Q100 not applicable - this is a general-purpose industrial-grade MCU, not automotive-qualified. Functional Safety (FuSa) per Microchip SAM D21G family documentation supports IEC 61508 SIL-2 type designs.