BLE112-A-V1C - BLE 4.0 Module with U.FL Antenna | Silicon Labs
부품 번호: BLE112-A-V1C ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $12.5 | $12.50 |
| 10 | $11.4 | $114.00 |
| 100 | $10.2 | $1,020.00 |
| 500 | $9.4 | $4,700.00 |
| 1,000 | $8.75 | $8,750.00 |
BLE112-A-V1C 개요
A Bluetooth Low Energy module is a complete wireless subsystem that integrates a BLE radio, a microcontroller, an antenna or antenna connector, and a certified protocol stack into a single surface-mount package. Within the wireless hierarchy, it sits below full Bluetooth systems and above bare radio chips, allowing designers to add BLE connectivity without developing RF layout, antenna matching, or regulatory certification themselves.
Key features include Bluetooth v4.0 single-mode compliance, support for both master and slave roles with 4 or more simultaneous connections in master mode, and an integrated Bluetooth Low Energy stack covering GAP, GATT, L2CAP, SMP, and BLE profiles. The fully integrated approach combines radio, microcontroller, and software stack in one certified module, dramatically reducing development effort.
Technically, the module integrates the BLE radio transceiver with an on-board microcontroller running the Bluegiga Bluetooth Smart software, so host processors can communicate over a simple interface or the application can run entirely on-module. The U.FL connector permits an external antenna for optimized range and enclosure flexibility, distinguishing the -V1C variant from the chip-antenna BLE112-A-V1.
Typical applications include battery-powered sensor nodes, proximity beacons, fitness and health accessories, and industrial wireless monitoring where a Class 2 link with an externally optimized antenna is preferred. The 2 V to 3.6 V supply range allows direct operation from a coin-cell battery.
Design consideration: the U.FL variant requires a mating antenna assembly (U.FL to SMA pigtail plus antenna) in the bill of materials, and the 50-ohm transmission line to the connector should follow controlled-impedance layout practice on the host PCB.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: BLE112-A-V1C — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: BLE112-A-V1C (동일 폼 팩터 및 풋프린트) — 차이점: Mounting Type.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
BLE112-A-V1
✅ 드롭인✓ 재고 있음
$16.89 / 개
데이터시트 보기 →BLE112-A-V1C 사양 (제조사 공개)
| Bluetooth Version | Bluetooth v4.0, single mode |
| Frequency Band | 2.4 GHz ISM |
| Air Data Rate | 2 Mbps |
| Supply Voltage Range | 2 V to 3.6 V |
| Power Class | Class 2 |
| Operating Modes | Master and slave |
| Simultaneous Connections | 4+ in master mode |
| Integrated Stack | GAP, GATT, L2CAP, SMP, BLE profiles |
| Antenna Type | U.FL connector (external antenna) |
| 실장 유형 | Surface Mount |
| Package Pin Count | 32-pin SMD |
| Integrated Solution | Bluetooth radio, microcontroller and software stack |
| Target Application | Low power sensors and accessories |
BLE112-A-V1C 인터페이스 및 커넥터
BLE112-A-V1C은(는) 제조사에서 공개한 대로 다음 인터페이스와 커넥터를 제공합니다: 블루투스, 전력 입력. 확장 헤더 핀아웃, 커넥터 핀 번호, 전기적 한계는 제조사 문서에 정의되어 있습니다.
| 블루투스 | Bluetooth v4.0, single mode |
| 전력 입력 | 2 V to 3.6 V |
다음을 참조하십시오: 제조사 문서 전체 확장 헤더 핀아웃 및 커넥터 핀 번호는 다음을 참조하십시오.
전력 및 열 특성
| 전력 입력 | 2 V to 3.6 V |
제조사에서 공개한 BLE112-A-V1C의 전력 입력 및 열 파라미터입니다.
일반적인 애플리케이션
BLE112-A-V1C 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Nodes, Fitness and Health Accessories, Bluetooth Proximity Beacons, Industrial Wireless Monitoring, Smart Home IoT Accessories, Embedded Systems Connectivity Add-On.
Battery-Powered Sensor Nodes
The BLE112-A-V1C fits coin-cell sensor nodes because its 2 V to 3.6 V supply range connects directly to a 3 V lithium cell without a regulator, and the integrated Bluetooth v4.0 stack handles GAP advertising and GATT services without host firmware. In a typical temperature or humidity node, the module spends most of its life in sleep and wakes for short advertising or connection events, preserving battery life. The U.FL antenna connector lets the designer place the antenna at the enclosure edge for optimal radiation even when the PCB sits inside a dense housing. Using the on-module microcontroller for sensing logic removes the need for a separate MCU, reducing BOM cost and sleep-state current.
추천
Fitness and Health Accessories
Wearable health devices such as heart-rate straps and activity trackers benefit from the BLE112-A-V1C's small 32-pin SMD module format, Bluetooth v4.0 single-mode compliance, and integrated GATT profile support, which enables interoperability with smartphones and tablets. The certified stack including SMP provides the pairing and bonding security required for personal health data. The 2 Mbps air data rate covers streaming of sensor samples at typical physiologic rates, while BLE connection intervals can be relaxed between measurements to save power. The U.FL connector allows the antenna to be routed to a strap or case position with clear radiation, improving link margin when the wearable is worn against the body, which strongly attenuates 2.4 GHz signals.
추천
Bluetooth Proximity Beacons
For iBeacon-style proximity applications, the BLE112-A-V1C transmits manufacturer-specific advertising packets using the integrated GAP layer, requiring only configuration firmware on the module's integrated microcontroller. Its 2 V to 3.6 V input suits direct coin-cell powering, a defining requirement for beacons deployed in quantity. The U.FL antenna variant is advantageous where the beacon housing is metallic or the antenna must be positioned for coverage, since a chip antenna near metal becomes detuned and loses range. Because the stack and radio are pre-certified, beacon deployments avoid per-design regulatory testing beyond the host product evaluation, and advertising interval and TX power can be tuned in firmware to trade range against multi-year battery life.
추천
Industrial Wireless Monitoring
In industrial environments, the BLE112-A-V1C provides a Class 2 Bluetooth Smart link for machine-status sensors, meter readers, and condition-monitoring nodes that report periodically to a smartphone, tablet, or BLE gateway. Master mode with 4 or more simultaneous connections allows one module to act as a small local hub polling several nearby peripheral sensors, consolidating data before forwarding. The external U.FL antenna is valuable inside control cabinets, where the module PCB can remain inside while the antenna is mounted on the cabinet exterior for reliable 2.4 GHz propagation. The wide 2 V to 3.6 V supply range accepts standard 3.3 V industrial rails, and the certified stack with SMP supports secured pairing for plant-floor data integrity.
추천
Smart Home IoT Accessories
Smart-home accessories such as door/window sensors, dimmer controls, and BLE-to-app configuration interfaces use the BLE112-A-V1C's integrated GAP, GATT, and profile stack so the product appears as a standard BLE peripheral to phones and home hubs without any host-side stack development. The single 2 V to 3.6 V supply works with both coin cells and 3.3 V house power. The module's integrated microcontroller can run the entire product application - debouncing switches, driving status LEDs, and managing sensor reads - eliminating an external MCU. The U.FL connector supports antenna placement optimized for whole-home coverage from a fixed installation point, and OTA-configurable advertising and GATT data let installers adjust behavior in the field.
추천
Embedded Systems Connectivity Add-On
Designers adding Bluetooth Smart connectivity to an existing embedded product can use the BLE112-A-V1C as a certified wireless co-processor: the host MCU exchanges data with the module over its supported interface while the module's integrated stack manages advertising, connections, pairing, and GATT. This architecture avoids porting a BLE stack to the host and keeps RF expertise off the critical path, since radio, matching, and stack are integrated and pre-certified. The 32-pin SMD module reflows onto the host PCB like a standard component, and the U.FL output allows a pigtail to an external antenna placed clear of metal shielding. The 2 Mbps data rate and Class 2 power suit short-to-medium-range data exchange at low energy cost.
추천
엔지니어링 참조 데이터: BLE112-A-V1C — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | BLE112-A-V1 |
|---|---|---|
| Package | 32-pin SMD module | 32-pin SMD module - same |
| Brand | Silicon Labs (Bluegiga) | Silicon Labs (Bluegiga) |
| Bluetooth Version | v4.0 single mode | v4.0 single mode |
| Antenna | U.FL connector (external) | Integrated chip antenna |
| Supply Voltage | 2 V to 3.6 V | 2 V to 3.6 V |
| Air Data Rate | 2 Mbps | 2 Mbps |
| Master Mode Connections | 4+ simultaneous | 4+ simultaneous |
| Integrated Stack | GAP, GATT, L2CAP, SMP, profiles | GAP, GATT, L2CAP, SMP, profiles |
주요 차별점
- External antenna flexibility via U.FL connector (vs BLE112-A-V1)
- Fully integrated certified solution (vs BLE112-A-V1)
- Trade-off: added assembly cost (vs BLE112-A-V1)
설계 노트
Route the U.FL antenna line as a controlled 50-ohm microstrip or coplanar waveguide from the module to the U.FL connector, keeping the trace as short as practical and referencing a continuous ground plane. Avoid routing the RF line under other signal layers or near switching regulators. Select a U.FL-to-SMA pigtail and antenna combination rated for 2.4 GHz, and secure the pigtail mechanically so repeated enclosure assembly does not stress the connector. Verify final radiated performance with a conducted or OTA test, since external antenna placement dominates real-world range.
Power the BLE112-A-V1C from a clean 2 V to 3.6 V rail; a 3 V coin cell or a 3.3 V LDO output are typical choices. Radio transmission draws burst current, so place low-ESR ceramic decoupling capacitors close to the module supply pins and ensure the source impedance of the supply (including coin-cell internal resistance) keeps the voltage above the 2 V minimum during TX bursts. Avoid long, thin supply traces from a shared rail; a dedicated decoupling network per the datasheet reference design prevents brownouts that manifest as BLE disconnections.
Do not substitute the -V1C (U.FL) footprint with the -V1 (chip antenna) without reviewing the mechanical design: a chip antenna requires a keep-out area free of copper and metal per the datasheet layout guidelines, while the -V1C requires clearance for the connector and pigtail. Also note that peripheral I/O pins lack internal pull-up/pull-down capability, so external resistors are needed where the application requires defined input levels. In power modes PM1, PM2, and PM3 the I/O pins retain their configured mode and output states, which designers should account for when computing sleep current.
규정 준수 정보
Compliance data was not present in the provided web data; consult the official Silicon Labs/Bluegiga product page and datasheet for RoHS/REACH certification status. The module itself is a certified Bluetooth product per the integrated stack description.
