CC1312PSIPMOTR - Sub-1GHz SiP RF Module | Texas Instruments
부품 번호: CC1312PSIPMOTR ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $21.8 | $21.80 |
| 10 | $20.65 | $206.50 |
| 100 | $19.53 | $1,953.00 |
| 500 | $18.6 | $9,300.00 |
| 1,000 | $17.75 | $17,750.00 |
CC1312PSIPMOTR 개요
A system-in-package wireless MCU combines a radio transceiver, a microcontroller, crystal oscillators, RF matching components and decoupling capacitors inside a single pre-tested package. In the power-management hierarchy of an IoT node, a SiP sits above a bare transceiver IC: it removes the hardest part of RF design, the antenna matching network and layout sensitivity, and replaces it with a surface-mount component that can be reflowed onto a standard PCB. The CC1312PSIP integrates a CC1312R device die plus an integrated power amplifier for increased link budget.
Key features include support for IEEE 802.15.4-based stacks (Wi-SUN, Thread-compatible PHYs) and proprietary Sub-1 GHz protocols, operation on the SimpleLink MCU platform, and a Common SimpleLink Low Power F2 SDK shared across the family. The integrated PA extends output power and therefore range compared with non-PA SiP versions, which matters for metering and streetlight meshes.
Technically, the device belongs to the SimpleLink F2 family and is supported by the SysConfig system configuration tool. TI explicitly states that the CC1312PSIP portfolio includes pin-compatible 2.4 GHz SiPs, so a product can migrate between communication standards (Sub-1 GHz and 2.4 GHz) on the same PCB footprint, protecting firmware and hardware investment.
Typical applications include Wi-SUN mesh networks for smart utilities, wireless sensor networks in the 868/915 MHz bands, and long-range IoT nodes where the PA-enhanced link budget enables multi-kilometer range in rural deployments.
Design consideration: as a SiP module, the CC1312PSIP still requires a clean 48-pin land pattern, ground vias under the package, and an antenna feed designed for the target band; follow the TI reference design impedance exactly.
This page synthesizes verified distributor data, drop-in alternatives and practical design notes not found on the manufacturer datasheet alone.
드롭인 대체품: CC1312PSIPMOTR — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
CC1352PSIPMOTR
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
CC1312PSIPMOT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
CC1312PSIPMOTR 사양 (제조사 공개)
| Product Type | Sub-1 GHz SiP wireless MCU module with integrated power amplifier |
| Frequency Range (Module) | 863 MHz to 930 MHz |
| Radio Tuning Range | 861 MHz to 1030 MHz |
| Protocols | IEEE 802.15.4, 6LoWPAN, Wi-SUN, mioty, proprietary Sub-1 GHz |
| 패키지 | QFM (MOT), 48 pins |
| 실장 유형 | Surface Mount |
| 동작 온도 | -40C to +105C |
| Temperature Grade (MOT) | -40 to 105 |
| Integrated Power Amplifier | Yes |
| Platform | TI SimpleLink MCU platform |
| SDK | SimpleLink Low Power F2 SDK |
| Configuration Tool | SysConfig |
| Pin-Compatible 2.4 GHz SiP Option | Yes (same-footprint portfolio) |
| Packaging | Tape and Reel (TR suffix) |
CC1312PSIPMOTR 인터페이스 및 커넥터
CC1312PSIPMOTR에 대해 제조사에서 공개한 인터페이스 목록이 없습니다. 커넥터 및 헤더 세부 정보는 제조사 문서를 참조하십시오.
다음을 참조하십시오: 제조사 문서 전체 확장 헤더 핀아웃 및 커넥터 핀 번호는 다음을 참조하십시오.
전력 및 열 특성
| 동작 온도 | -40C to +105C |
제조사에서 공개한 CC1312PSIPMOTR의 전력 입력 및 열 파라미터입니다.
일반적인 애플리케이션
CC1312PSIPMOTR 적합 용도: 6 애플리케이션s: Wi-SUN Smart Utility Mesh Networks, Wireless Sensor Networks (868/915 MHz), Streetlight and Smart City Infrastructure, Long-Range Telemetry and SCADA Nodes, Asset Tracking and Logistics, Home and Building Automation Hubs.
Wi-SUN Smart Utility Mesh Networks
The CC1312PSIPMOTR fits Wi-SUN mesh deployments such as advanced metering infrastructure and distribution automation because its integrated power amplifier increases the Sub-1 GHz link budget, extending node-to-node range in 868/915 MHz bands where propagation penetrates buildings and foliage far better than 2.4 GHz. The CC1312PSIP natively supports Wi-SUN FAN on the SimpleLink Low Power F2 SDK, so certified-stack integration requires no proprietary MAC development. Placed as the main wireless MCU on the node PCB, it drives the antenna through a simple 50-ohm feed, and the -40C to +105C rating covers pole-mounted and vault enclosures. The trade-off versus a non-PA module is higher TX current draw, so battery-only nodes should duty-cycle transmissions.
추천
Wireless Sensor Networks (868/915 MHz)
For industrial wireless sensor networks, the CC1312PSIPMOTR acts as a single-chip sensor node: its ARM-based wireless MCU handles sensing, protocol and radio duties without a host processor, cutting BOM count and sleep current. The 863-930 MHz coverage with integrated PA delivers multi-kilometer line-of-sight range for agricultural monitoring, tank-level telemetry and cold-chain loggers spread across large sites. Using proprietary Sub-1 GHz modes on the SimpleLink F2 SDK lets designers optimize data rate versus sensitivity, trading throughput for link margin. Because the RF matching and 48 MHz crystal are factory-integrated in the SiP, each sensor node PCB needs no RF tuning, which dramatically improves first-pass manufacturing yield across contract manufacturers.
추천
Streetlight and Smart City Infrastructure
Smart streetlight controllers and city IoT gateways benefit from the CC1312PSIPMOTR's combination of PA-enhanced range and 802.15.4 mesh protocol support. Mesh networking across hundreds of luminaires in the 868/915 MHz bands self-heals and scales without cellular subscription costs, and the module's integrated PA ensures reliable links even when controllers are mounted inside metal pole bases with compromised antennas. The -40C to +105C temperature range handles sealed enclosures exposed to direct summer sun. Designers typically pair the module with a mains-powered supply, so the higher TX current of the PA path is acceptable, and the SysConfig tool simplifies adapting the same PCB to a 2.4 GHz standard later by swapping to a pin-compatible SiP.
추천
Long-Range Telemetry and SCADA Nodes
Remote SCADA endpoints, such as irrigation controllers, pipeline monitors and wellhead telemetry, use the CC1312PSIPMOTR where cellular coverage is absent and licensed radios are too costly. The 861-1030 MHz radio tuning range lets one hardware design serve region-specific frequency plans (868 MHz Europe, 915 MHz ISM US, 920 MHz Japan) with antenna and firmware changes only, thanks to the integrated crystal and matching already certified inside the SiP. The PA lifts effective radiated power toward the regulatory limit, maximizing range per hop across sparse topologies. The industrial -40C to +105C rating and 48-pin reflowable QFM package suit conformal-coated, vibration-prone outdoor enclosures typical of field telemetry installations.
추천
Asset Tracking and Logistics
In long-range asset tracking for shipping containers, agricultural equipment and rental fleets, the CC1312PSIPMOTR provides a low-power Sub-1 GHz link to gateways installed on vehicles or site infrastructure, complementing or replacing cellular where coverage or cost is a constraint. The integrated PA compensates for small or partially shielded antennas on metal assets, and the wireless MCU's low sleep current extends battery life to multi-year service intervals. Firmware can implement proprietary long-range PHYs on the SimpleLink F2 SDK with AES security. Because the SiP integrates crystals and matching, thin tracker PCBs can route the 48-pin land pattern on two layers near the battery, keeping the module small enough for concealed mounting brackets.
추천
Home and Building Automation Hubs
Sub-1 GHz home automation hubs, garage-door controllers and security sensors use the CC1312PSIPMOTR to reach distant battery sensors through walls, where 2.4 GHz protocols struggle. The module's 802.15.4 and proprietary stack support lets hub manufacturers serve multiple sensor ecosystems from one radio, and TI's pin-compatible 2.4 GHz SiP portfolio means the same hub PCB can be respun for Thread or Bluetooth variants without RF redesign. The PA improves hub downlink range so battery sensors can use lower TX power, saving coin-cell energy. The 48-pin QFM reflows on standard SMT lines with the same land-pattern design used across the SimpleLink SiP family, simplifying dual-SKU manufacturing.
추천
추천 제품 요약
엔지니어링 참조 데이터: CC1312PSIPMOTR — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | CC1352PSIPMOTR | CC1312PSIPMOT |
|---|---|---|---|
| Package | QFM (MOT), 48 pins, SiP | QFM (MOT), 48 pins - same footprint | QFM (MOT), 48 pins - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Frequency Bands | 863 MHz to 930 MHz (radio 861-1030 MHz) | Sub-1 GHz plus 2.4 GHz | 863 MHz to 930 MHz |
| Integrated Power Amplifier | Yes | Yes | Yes |
| Operating Temperature | -40C to +105C | -40C to +105C (MOT grade) | -40C to +105C |
| Protocols | 802.15.4, 6LoWPAN, Wi-SUN, mioty, proprietary | Same plus BLE/2.4 GHz stacks | 802.15.4, 6LoWPAN, Wi-SUN, mioty, proprietary |
| SDK / Software | SimpleLink Low Power F2 SDK + SysConfig | SimpleLink Low Power F2 SDK (shared) | SimpleLink Low Power F2 SDK (shared) |
| Packaging / Delivery | Tape & Reel (TR) | Tape & Reel | Tray / non-reel variant |
주요 차별점
- Integrated power amplifier for extended range (vs CC1312R (discrete, non-PA))
- RF design complexity removed by SiP integration (vs CC1312R QFN discrete design)
- Footprint migration path to 2.4 GHz (vs CC1352PSIPMOTR)
설계 노트
Implement the 48-pin QFM (MOT) land pattern exactly per the TI CC1312PSIP datasheet package outline, including the underside land array and the recommended via stitching to the ground plane. SiP modules depend on the PCB ground for RF return paths; deviating from the reference land pattern detunes the integrated matching and degrades output power and harmonics. Reuse the TI reference design footprint and antenna feed from the CC1312PSIP design resources rather than re-creating the RF section.
Supply the module with a low-noise rail and size the DC-DC or LDO for TX burst currents, which are substantially higher on PA-enabled SiPs than non-PA parts during 802.15.4 and Wi-SUN transmissions. Use bulk capacitance near the supply pins plus 100 nF ceramics, and isolate the RF module supply from noisy digital rails. For battery nodes, verify regulator quiescent current plus module sleep current against the datasheet figures to compute realistic battery life; do not use active-mode currents in lifetime estimates.
Two frequent mistakes: first, assuming the 863-930 MHz module ordering variant covers the full 861-1030 MHz radio tuning range for any region - confirm the correct ordering suffix for your target market (EU 868, US 915, JP 920) and certify per region. Second, using the 2.4 GHz pin-compatible SiPs (e.g., CC1352PSIP) without software migration: the footprint matches but stacks and SysConfig configurations differ. Budget firmware rework when changing radio standard even with a pin-compatible part.
규정 준수 정보
Compliance data not present in the provided web data; consult the TI product page quality/environmental section for RoHS/REACH status of CC1312PSIPMOTR.
