CD4522BM - 4-Bit Programmable BCD Counter | Texas Instruments
부품 번호: CD4522BM ✓ 활성CD4522BM 개요
A BCD divide-by-N counter is a digital logic IC that counts in binary-coded decimal and generates a terminal-count indication after a selected number of input transitions. In the broader semiconductor hierarchy, this function belongs to counters and dividers, then to logic ICs, digital semiconductors, and programmable CMOS devices. The CD4522B family is useful where a system must divide a clock into programmable decade-based intervals without requiring a microprocessor or programmable logic device.
The internally synchronous counter architecture supports high internal and external operating speeds, while the logic-edge-clocked design increments on a positive Clock transition or on a negative Clock Inhibit transition. A decoded zero-state output simplifies the end-of-count detection normally required by divide-by-N systems. The verified manufacturer material also states that the device is 100% tested for quiescent current at 20 V and receives parametric testing at 5 V, 10 V, and 15 V, providing useful production-control coverage across common CMOS operating points.
The programmable divide count is configured through the counter's control inputs, while cascade feedback permits multiple counter sections to implement larger division ratios. This architecture reduces the external logic needed for timing dividers, periodic-event generators, sequence counters, and clock-staging circuits. Exact propagation-delay and maximum-frequency limits were not present in the supplied verified snippets and should therefore be confirmed in the manufacturer datasheet before relying on timing margins.
Typical applications include decade counters, programmable frequency dividers, industrial timing modules, digital clock generation, pulse-rate counting, and multistage cascaded division systems. The CD4522BM is particularly appropriate when a fixed, reliable CMOS counter is preferred over software timing, especially where the final count must be electrically programmable rather than fixed in firmware.
Designers should connect the decoded zero output and preset-enable functions according to the intended single-stage or cascade configuration, and should account for supply-voltage-dependent propagation delay in high-speed clock trees. Decoupling capacitors should be placed close to the power and ground pins, while unused inputs must be held at a defined logic level rather than left floating.
This page consolidates verified manufacturer and distributor information, package details, sourcing links, strict drop-in candidates, and practical design guidance. It distinguishes documented characteristics from parameters that still require confirmation from the full CD4522B datasheet, helping engineers make a defensible sourcing and design decision.
드롭인 대체품: CD4522BM — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
CD4522BMT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
CD4522BMTG4
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
CD4522BMG4
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
CD4522BM96
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
CD4522B
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
CD4522BM 최대 정격 & 전기적 특성
| Counter Type | Programmable BCD divide-by-N counter |
| Logic Family | CMOS |
| Counting Elements | 1 element |
| Counter Resolution | 4 bits |
| Supply Voltage Range | 3 V to 18 V |
| 동작 온도 범위 | -55 °C to +125 °C |
| 패키지 | 16-pin SOIC (D) |
| 핀 수 | 16 pins |
| 실장 유형 | Surface mount |
| Clocking Method | Logic edge-clocked |
| Clock Increment Edge | Positive Clock transition |
| Clock Inhibit Increment Edge | Negative Clock Inhibit transition |
| Internal Timing Architecture | Internally synchronous |
| Terminal Count Output | Decoded 0-state output |
| Quiescent Current Test Voltage | 20 V |
| Parametric Test Supply Points | 5 V, 10 V, and 15 V |
| Cascading Capability | Supported through cascade feedback |
| RoHS 상태 | Unknown |
| REACH Status | Unknown |
CD4522BM 16-pin soic (d) 핀 구성 가이드
CD4522BM(16-pin soic (d) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: CD4522BM.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
CD4522BM 적합 용도: 6 애플리케이션s: Programmable Industrial Timing, Digital Clock Generation, Pulse and Event Counting, Cascaded Frequency Divider, Instrumentation Timing Reference, Automotive or Robust Control Timing.
Programmable Industrial Timing
The CD4522BM fits hardware timing systems that divide a periodic input into selectable BCD intervals. Its 4-bit counting element, decoded zero-state output, and programmable divide-by-N operation allow terminal-count events to be generated without continuous software involvement. The verified 3 V to 18 V supply range supports multiple industrial logic levels, while the -55 °C to +125 °C specification covers a broad temperature range. In a timer implementation, the source clock enters Clock, the divide count is programmed through the counter control inputs, and the decoded zero output triggers the next system event. Exact maximum frequency and propagation delay must be obtained from the full manufacturer datasheet before closing the timing budget.
추천
Digital Clock Generation
The CD4522BM can organize a master oscillator into useful timing intervals for digital clocks and sequencers. Its internal synchronous architecture and edge-clocked counting method are useful when a clean divide-by-N stage is required between a master clock and lower-rate system timing. The decoded zero output provides a convenient rollover indication, and cascade feedback allows a larger divide ratio to be built across stages. Because CMOS propagation delay varies with supply voltage, the clock designer should evaluate the timing path at the minimum operating voltage and highest temperature. This makes the CD4522BM especially practical for fixed-rate industrial clock trees where a dedicated programmable counter is preferred over firmware.
추천
Pulse and Event Counting
The CD4522BM is suitable for counting recurring pulses and generating a terminal event after a programmable number of cycles. Its counter accepts positive Clock transitions, while the negative Clock Inhibit transition provides an alternate incrementing event according to the verified manufacturer description. This allows the same counter concept to support repetitive event counting, batch processing, and periodic actuator commands. The decoded zero output can mark completion of each counted sequence, while the programmable divide count determines how many events must accumulate. Engineers should account for switch bounce, input conditioning, and minimum clock pulse width, none of which were quantified in the supplied snippets and all of which must be confirmed from the manufacturer documentation.
추천
Cascaded Frequency Divider
The CD4522BM can participate in a multistage frequency-divider chain when a single counter cannot provide the required division ratio. Its cascade-feedback capability reduces external logic, while the decoded zero output identifies each stage's terminal count. This arrangement is useful for deriving low-frequency timing from a higher-frequency source in industrial controllers, test equipment, and sequential fixtures. The design must preserve signal-quality margins through each stage and account for cumulative propagation delay and supply dependence. The verified 3 V to 18 V operating range allows consistent operation across several common supply choices, but exact cascade timing must be calculated using the full CD4522B datasheet rather than the search snippets.
추천
Instrumentation Timing Reference
The CD4522BM can divide an oscillator into repeatable timing intervals for test and measurement systems. Its hardware-defined divide ratio provides a predictable event cadence without loading a controller with periodic interrupt handling, and the decoded zero output can mark the end of each interval. The wide -55 °C to +125 °C rating supports instrumentation environments when the surrounding system is also appropriately qualified. Use of a CMOS counter can also reduce clock-tree complexity compared with chained general-purpose logic. The main design trade-off is that propagation-delay and maximum-frequency figures were not included in the verified snippets, so an instrumentation designer must confirm timing at every required supply voltage and temperature before using the output as a precision reference.
추천
Automotive or Robust Control Timing
The CD4522BM's -55 °C to +125 °C operating range makes it a candidate for timing functions in demanding equipment, although that temperature rating does not itself establish AEC-Q100 qualification. In a robust control system, the counter can divide a repetitive supervisory clock and indicate rollover for maintenance counters, sampling windows, or delayed events. Its internal synchronous design and decoded terminal-count output reduce the number of external gates required. Compliance and qualification must be verified for the exact ordered suffix before use in automotive, medical, or safety-regulated production. Engineers should also confirm whether the application requires a specific qualification grade, traceability, or change-control documentation beyond the published electrical and temperature specifications.
추천
추천 제품 요약
엔지니어링 참조 데이터: CD4522BM — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | CD4522BMT | CD4522BMTG4 | CD4522BMG4 | CD4522BM96 | CD4522B |
|---|---|---|---|---|---|---|
| Package | SOIC-16 (D) | SOIC-16 (D) | SOIC-16 (D) | SOIC-16 (D) | SOIC-16 (D) | SOIC-16 (D) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Counter Function | Programmable BCD divide-by-N counter | Programmable BCD divide-by-N counter | Programmable BCD divide-by-N counter | Programmable BCD divide-by-N counter | Programmable BCD divide-by-N counter | Programmable BCD divide-by-N counter |
주요 차별점
- Explicitly verified complete replacement option (vs CD4522BMT)
- Programmable terminal-count indication (vs CD4522BMG4)
- Broad verified supply and temperature coverage (vs CD4522BMTG4)
설계 노트
Do not infer timing performance from the counter's internal synchronous description alone. Obtain the manufacturer datasheet and evaluate propagation delay, transition-time limits, and maximum operating frequency at the minimum planned supply voltage and worst-case temperature. The supplied search results confirm the 3 V to 18 V range but do not provide verified timing numbers, so those values remain a design-review dependency.
Place the supply bypass capacitor close to the device's VDD and ground connections, and route the clock and control traces away from noisy switching nodes. The CD4522BM is a 16-pin SOIC counter whose decoded zero output and control inputs participate in timing, so long traces can add delay or allow coupling into the count sequence. Use a solid ground plane and avoid sharing narrow return paths with high-current loads.
Use the decoded zero output and preset-enable input according to the manufacturer's single-stage or cascade configuration. A mistaken feedback connection can prevent the intended terminal count from being reached or create an unstable count sequence. Cascade feedback is specifically provided for multi-stage divide-by-N operation, so it should replace redundant external feedback logic rather than be added as an additional asynchronous path.
Keep every unused CMOS input at a defined logic level. Floating control, clock-inhibit, preset, or reset-related inputs can consume additional current and may produce uncertain behavior near switching thresholds. Confirm which inputs are asynchronous and which are edge-sensitive in the full CD4522B datasheet, and ensure that asynchronous controls are filtered when they originate from noisy or mechanical sources.
규정 준수 정보
The supplied verified snippets do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. The -55 °C to +125 °C temperature rating must not be interpreted as AEC-Q100 qualification.