CD4541BE - 100 kHz Programmable Timer | Texas Instruments
부품 번호: CD4541BE ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0.0857 | $0.09 |
| 10 | $0.0857 | $0.86 |
| 100 | $0.0857 | $8.57 |
| 500 | $0.0857 | $42.85 |
| 1,000 | $0.0857 | $85.70 |
CD4541BE 개요
A programmable timer is a timing IC that generates or measures intervals using digital counters and, often, an external resistor-capacitor network. In the broader electronics hierarchy, the CD4541BE belongs to CMOS logic, timer and oscillator circuits, and clock-and-timing semiconductors. Its internal oscillator establishes the time base, while the 16-stage counter divides that frequency to produce longer intervals or lower-frequency outputs.
The MODE input, located at pin 10, provides selectable operating modes. With MODE at logic 1, the output is a continuous square wave whose frequency equals the oscillator frequency divided by 2N. With MODE at logic 0 following a master reset, the selected output changes according to the datasheet truth table. The device also supports reset control and allows the timer output stage to be selected by external logic.
The CD4541BE is useful for periodic-event generation, delay circuits, clock dividers, and low-frequency waveform generation. Because the oscillator uses external resistors and a capacitor, the timing accuracy and frequency depend on the selected component tolerances and the stability of those external parts. Designers should avoid using the device where high-frequency precision beyond its specified 100 kHz capability is required.
Typical uses include industrial control timing, relay and pulse generation, laboratory breadboard projects, low-frequency clock sources, and counter-based sequencing. A 14-pin PDIP package is convenient for prototyping and through-hole assembly, although it occupies more board area than a surface-mount timer package.
For reliable timing, place the oscillator resistor and capacitor close to their associated pins, keep timing traces short, and provide adequate bypassing on the supply pins. Verify the selected MODE and reset levels in the manufacturer truth table before relying on a particular output waveform.
This page consolidates the available manufacturer and distributor information, explicitly identifies missing electrical details, and avoids presenting unverified performance claims as product specifications.
드롭인 대체품: CD4541BE — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: CD4541BE (동일 폼 팩터 및 풋프린트) — 차이점: Package.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
CD4541BMT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
CD4541BF3A
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC14541BCPG
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
CD4541BE 사양
| Product Type | CMOS programmable timer |
| Maximum Oscillator Frequency | 100 kHz |
| Supply Voltage Rating | 20 V high-voltage rating |
| Counter Stages | 16 stages |
| Oscillator Timing Components | 2 resistors and 1 capacitor |
| Power-On Reset | Automatic power-on reset |
| MODE Input | Pin 10; logic 1 for continuous square-wave mode and logic 0 for reset-dependent output mode |
| Output Frequency | Oscillator frequency divided by 2N |
| 패키지 | 14-pin PDIP |
| 실장 유형 | Through-hole |
| Logic Family | CMOS |
| Master Reset | Supported |
| Output Control Logic | Programmable output selection |
| Supply Voltage Maximum | 20 V rating |
CD4541BE 14-pin pdip 핀 구성 가이드
CD4541BE(14-pin pdip 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: CD4541BE.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
CD4541BE 적합 용도: 6 애플리케이션s: Periodic Clock Generation, Pulse and Delay Generation, Industrial Event Sequencing, Laboratory Function Generator, Countdown and Repetitive Trigger Circuits, Low-Frequency Embedded Control.
Periodic Clock Generation
The CD4541BE fits low-frequency periodic clock generation because its external two-resistor, one-capacitor network establishes the oscillator time base and the 16-stage counter extends the available timing range. In continuous square-wave mode, MODE pin 10 at logic 1 divides the oscillator frequency according to the selected counter stage. This approach is useful for clocking a small control system, cycling a display state, or producing a repeatable service pulse without a microcontroller. The engineering tradeoff is that timing accuracy depends on the external resistor and capacitor tolerances, so stable components and short PCB traces are important.
추천
Pulse and Delay Generation
Use the CD4541BE when a simple hardware pulse train or delayed transition is required. Its oscillator, 16-stage counter, reset input, and selectable output logic allow the timing period to be extended without using a processor timing loop. The MODE input determines whether the selected output operates as a continuous divided square wave or follows the reset-dependent sequence described in the manufacturer truth table. Because the verified data does not specify exact timing tolerances, calculate the oscillator values from the datasheet and validate them across temperature and supply variation before using the circuit for safety-critical timing.
추천
Industrial Event Sequencing
The CD4541BE can support simple industrial event sequencing where a periodic output drives a relay, counter, indicator, or actuator interface. Its 20 V high-voltage rating and CMOS timer architecture are relevant to control-oriented circuits, although the exact input protection and output-drive limits must come from the complete manufacturer datasheet. Keep the timer IC separate from inductive loads and use suitable driver transistors, flyback protection, and isolation where required. The device is better suited to low-frequency deterministic sequencing than to high-rate communication or precision real-time measurement.
추천
Laboratory Function Generator
The CD4541BE is useful in a low-frequency laboratory clock or square-wave generator built around external timing components. MODE pin 10 can select continuous square-wave operation, while the counter stages reduce the oscillator frequency by powers of two according to the manufacturer description. This makes it convenient for educational breadboard circuits, slow trigger sources, and basic timing demonstrations. For laboratory work, measure the actual output frequency because tolerance, temperature drift, and supply conditions will influence the result; do not interpret the 100 kHz listing as a guaranteed precision frequency reference.
추천
Countdown and Repetitive Trigger Circuits
The 16-stage binary counter and programmable output logic make the CD4541BE appropriate for repetitive trigger or countdown-style circuits. After a master reset, the selected output follows the mode-dependent sequence defined in the truth table, allowing external logic to detect a terminal count or periodic interval. This can simplify older control boards that need a hardware timer rather than firmware timing. Use a suitable output driver if the load requires more current than the verified data specifies, and preserve the reset polarity and timing margins shown in the manufacturer documentation.
추천
Low-Frequency Embedded Control
A CD4541BE can provide an independent low-frequency timing reference beside a microcontroller or discrete control logic. Its standalone oscillator and counter do not depend on firmware execution, making the part useful for watchdog-like cadence, display multiplexing, or periodic maintenance requests in a larger embedded system. The 14-pin PDIP footprint is advantageous for prototypes and repairable through-hole assemblies, though it consumes more board area than a surface-mount timer. Verify supply-voltage compatibility, input levels, and output-drive requirements against the target controller and protection circuitry.
추천
추천 제품 요약
엔지니어링 참조 데이터: CD4541BE — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | CD4541BMT | CD4541BF3A | MC14541BCPG |
|---|---|---|---|---|
| Package | 14-pin PDIP | 14-pin PDIP candidate; verify exact ordering variant | 14-pin PDIP candidate; verify exact ordering variant | 14-pin PDIP candidate; verify manufacturer data |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | onsemi |
| Function | CMOS programmable timer | CD4541B-family timer candidate | CD4541B-family timer candidate | Programmable timer candidate |
주요 차별점
- Standalone hardware timing (vs ATMEGA328-AU)
- Through-hole prototyping convenience (vs MC14541BCPG)
- Programmable output behavior (vs CD4541BMT)
설계 노트
Place the two oscillator resistors and the timing capacitor close to the associated CD4541BE pins, and route the timing network as a compact analog subcircuit. Keep oscillator traces away from switching-regulator outputs, relay-driver nodes, and long high-current paths. If the timing capacitor is sensitive, use a short ground return and follow the manufacturer layout guidance for the selected package.
Do not treat the 100 kHz listing as a complete timing-accuracy specification. The external resistor and capacitor tolerances, temperature coefficient, supply variation, and counter configuration all affect the resulting period. Verify the calculated oscillator frequency on the assembled board and use the MODE pin and master-reset truth table from the Texas Instruments datasheet before designing the external logic.
Confirm the supply voltage and input/output limits against the complete manufacturer datasheet before connecting the timer to a 20 V-rated control circuit. The verified results establish a 20 V high-voltage type designation, but they do not provide the complete operating-current, output-drive, or absolute-maximum table. Add suitable protection and decoupling based on those verified limits rather than inferring them from the package name.
The 14-pin PDIP format is easy to prototype but occupies substantial board area. Keep the oscillator components away from long reset traces and noisy control outputs, and provide a local supply bypass path. When upgrading a design to a surface-mount package, treat the change as a footprint migration and verify pin numbering, orientation, and timing-node placement rather than assuming a direct replacement.
규정 준수 정보
The supplied verified data identifies a Texas Instruments CMOS timer and a 20 V high-voltage rating but does not provide RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statements.
