DSPIC33FJ16MC102T-I/SS - 16-bit Motor Control DSC 16 MIPS | Microchip
부품 번호: DSPIC33FJ16MC102T-I/SS ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $4.2 | $4.20 |
| 10 | $3.78 | $37.80 |
| 100 | $3.36 | $336.00 |
| 500 | $3.02 | $1,510.00 |
| 1,000 | $2.68 | $2,680.00 |
DSPIC33FJ16MC102T-I/SS 개요
A digital signal controller combines the computational throughput of a DSP with the peripheral integration and ease of use of a microcontroller. Within the power-management hierarchy, the DSC sits between a general-purpose MCU and a dedicated DSP, making the dsPIC33F family a common choice for closed-loop motor control, digital power conversion, and sensor signal processing.
Key features include a motor control PWM (MCPWM) module for driving three-phase inverters, the CTMU (Charge Time Measurement Unit) for touch sensing and time measurement, and Peripheral Pin Select (PPS) for flexible remapping of digital peripherals onto I/O pins. Core-independent peripherals such as POR, brown-out detect/reset, and a watchdog timer improve system robustness. Connectivity covers I2C, SPI, UART/USART, IrDA, and LINbus, allowing direct interfacing with gate drivers, sensors, and automotive sub-networks.
Architecturally, the dsPIC33F core uses an enhanced 16-bit pipeline with DSP instruction support (barrel shifter, multiply-accumulate), operating from a 3.0V to 3.6V supply with a nominal 3.3V. The -I temperature grade covers -40C to +85C for industrial environments; the /SS suffix denotes the 28-lead SSOP surface-mount package and Tape-and-Reel delivery for automated assembly.
Typical applications include brushless DC and permanent-magnet motor drives, switch-mode power supplies and digital lighting, and embedded control nodes in industrial automation requiring LIN or UART connectivity.
Design consideration: budget program memory carefully - with 16KB FLASH, use the free MPLAB X toolchain and avoid heavy middleware stacks; the smaller 12KB dsPIC33FJ12MC202 may suffice for simple loops, while the 32KB variants give headroom.
This page synthesizes distributor pricing context, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet alone.
드롭인 대체품: DSPIC33FJ16MC102T-I/SS — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: DSPIC33FJ16MC102T-I/SS (동일 폼 팩터 및 풋프린트) — 차이점: Package, Operating Temperature, ADC, Core Architecture, Max CPU Speed.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
DSPIC33FJ16MC102-E/SS
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
DSPIC33FJ32MC102-I/SS
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$2.85 / 개
데이터시트 보기 →DSPIC33FJ32MC202-I/SS
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$3.75 / 개
데이터시트 보기 →DSPIC33FJ12MC202-I/SS
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$2.62 / 개
데이터시트 보기 →DSPIC33FJ16GP102T-I/SS
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$1.95 / 개
데이터시트 보기 →DSPIC33FJ16MC102T-I/SS 최대 정격 & 전기적 특성
| Core Architecture | 16-bit dsPIC33F |
| Max Performance | 16 MIPS |
| Program Memory (FLASH) | 16 KB |
| RAM | 1 KB |
| Supply Voltage Range | 3.0 V to 3.6 V (nominal 3.3 V) |
| 패키지 | 28-SSOP |
| 동작 온도 | -40C to +85C (Industrial, -I grade) |
| Communication Interfaces | I2C, SPI, UART/USART, IrDA, LINbus |
| Motor Control PWM | Yes (MCPWM module) |
| CTMU | Yes (Charge Time Measurement Unit) |
| Peripheral Pin Select (PPS) | Yes |
| Comparators | High-speed comparators (up to 4 per family datasheet) |
| Reset/Safety Peripherals | POR, Brown-out Detect/Reset, WDT |
| 실장 유형 | Surface Mount |
| Packaging | Tape & Reel (T suffix) |
| RoHS 상태 | Lead-free, RoHS compliant package body per family datasheet |
DSPIC33FJ16MC102T-I/SS 28-ssop 핀 구성 가이드
DSPIC33FJ16MC102T-I/SS(28-ssop 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: DSPIC33FJ16MC102T-I/SS.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
DSPIC33FJ16MC102T-I/SS 적합 용도: 6 애플리케이션s: BLDC/PMSM Motor Drives, Switch-Mode Power Supplies and Digital Lighting, Industrial Automation Sensor Nodes, Automotive Sub-Network Modules, Capacitive Touch and Time-Measurement Systems, Embedded Signal Processing and Data Acquisition.
BLDC/PMSM Motor Drives
The DSPIC33FJ16MC102T-I/SS was designed specifically for digital motor control: its dedicated MCPWM module generates complementary PWM outputs with hardware dead-time insertion, and high-speed comparators provide fast overcurrent trip without CPU latency. At 16 MIPS with DSP multiply-accumulate instructions, it executes field-oriented control (FOC) or sensorless trapezoidal BLDC loops for low- to mid-power fans, pumps, and appliances. Typical topology places the DSC between a current-shunt sense network and a three-phase gate driver, closing current loops in the tens-of-microseconds range. The 16KB FLASH accommodates a full FOC routine plus LIN or UART communications, making it a cost-optimized single-chip drive controller.
추천
Switch-Mode Power Supplies and Digital Lighting
In digital power conversion, the DSPIC33FJ16MC102T-I/SS implements voltage-mode or current-mode control loops for LLC, buck, and PFC stages. The 16-bit core at 16 MIPS provides the loop bandwidth needed for 100-500 kHz converters, while PPS lets the designer route PWM outputs and ADC-trigger sources flexibly to minimize PCB crossings. In LED drivers and HID ballast replacements, the CTMU and comparators support fast fault detection and dimming-signal measurement. The 3.0V-3.6V operation suits designs with a 3.3V logic rail derived from an auxiliary flyback winding, and the brown-out reset guarantees safe startup behavior under sagging input conditions.
추천
Industrial Automation Sensor Nodes
As a compact industrial control node, the DSPIC33FJ16MC102T-I/SS combines UART/USART, I2C, SPI, IrDA, and LINbus connectivity with the CTMU for capacitive or resistive sensing, allowing one 28-pin device to gather sensor data, run local filtering algorithms, and report over industrial serial networks. The -40C to +85C industrial temperature grade covers uncontrolled factory-floor environments, and the watchdog timer plus brown-out detection maintain watchdog-supervised operation during power disturbances. PPS pin remapping lets a single PCB layout serve multiple product variants by changing only firmware routing, reducing SKU proliferation and qualification costs in distributed I/O and sensing applications.
추천
Automotive Sub-Network Modules
LINbus support makes the DSPIC33FJ16MC102T-I/SS well suited to automotive body and actuator sub-networks - seat adjusters, mirror controls, HVAC dampers, and small pump drives - where LIN is the mandated low-cost bus. The 16 MIPS core runs the LIN 2.x protocol stack alongside a small motor-control loop, while PPS allows flexible placement of LIN transceiver UART pins. Although this standard part is not AEC-Q100 qualified, it serves off-road, agricultural, and Tier-2 industrial-vehicle modules where full automotive qualification is not required; for under-hood temperatures, move to the -40C to +125C E-grade variant in the same 28-SSOP footprint.
추천
Capacitive Touch and Time-Measurement Systems
The integrated Charge Time Measurement Unit (CTMU) turns the DSPIC33FJ16MC102T-I/SS into a single-chip touch interface: it injects precise charge currents into touch pads and measures charge time, detecting finger capacitance changes without a dedicated touch controller. The same CTMU supports ultrasonic flow measurement and resistance/capacitance metrology by timing charge intervals. Running the acquisition and debounce firmware within 16KB FLASH, the device can also drive feedback (LED, buzzer, or UART report) from the same pins via PPS remapping. This suits appliance panels, small HMI keypads, and low-cost instruments where a separate touch IC would add BOM cost and board area.
추천
Embedded Signal Processing and Data Acquisition
With its DSP engine - barrel shifter, hardware multiply-accumulate, and modulo addressing - the DSPIC33FJ16MC102T-I/SS performs real-time digital filtering (IIR/FIR), FFT-based analysis, and sensor linearization on-board. The 1KB RAM constrains block sizes, so designers typically stream samples through small FIR filters rather than large FFT frames; for heavier processing, the pin-compatible DSPIC33FJ32MC102 doubles program space for coefficient tables and stack. Typical uses include vibration monitoring nodes, current-signal conditioning for predictive maintenance, and precision analog front-end control where the high-speed comparators provide hardware limiting and the UART streams processed results to a host controller.
추천
추천 제품 요약
엔지니어링 참조 데이터: DSPIC33FJ16MC102T-I/SS — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | DSPIC33FJ16MC102-E/SS | DSPIC33FJ32MC102-I/SS | DSPIC33FJ32MC202-I/SS | DSPIC33FJ12MC202-I/SS | DSPIC33FJ16GP102T-I/SS |
|---|---|---|---|---|---|---|
| Package | 28-SSOP | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (FLASH) | 16 KB | 16 KB | 32 KB | 32 KB | 12 KB | 16 KB |
| RAM | 1 KB | 1 KB | 2 KB | 2 KB | 1 KB | 1 KB |
| Performance | 16 MIPS | 16 MIPS | 16 MIPS | 16 MIPS | 16 MIPS | 16 MIPS |
| Motor Control PWM (MCPWM) | Yes | Yes | Yes | Yes | Yes | No (GP variant) |
| Operating Temperature | -40C to +85C | -40C to +125C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Supply Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
주요 차별점
- Dedicated motor control PWM with dead-time insertion (vs DSPIC33FJ16GP102T-I/SS)
- Extended temperature option on identical silicon (vs DSPIC33FJ16MC102-E/SS)
- Memory-scaling path without redesign (vs DSPIC33FJ32MC102-I/SS)
설계 노트
The DSPIC33FJ16MC102T-I/SS requires a tightly regulated 3.0V-3.6V supply; exceeding 3.6V stresses the core regulator. Decouple each VDD pin with 0.1uF ceramic capacitors placed within 2 mm of the pins, plus 4.7-10uF bulk near the device. On motor-drive boards, separate the analog supply of the ADC/comparator inputs from gate-driver switching noise with an RC filter or ferrite bead. Estimated: at 16 MIPS full activity, core current draw is in the tens-of-mA range per the family datasheet, so a 100 mA-rated 3.3V LDO generally suffices.
In motor-control layouts, keep the MCPWM output traces short to gate drivers and route current-sense feedback away from PWM switching nodes. Use the exposed routing freedom of Peripheral Pin Select (PPS) during layout: assign PWM, UART, and comparator I/O on firmware before finalizing copper so that noisy PWM lines never cross analog sense traces. Place the CTMU touch pads with guard traces to adjacent ground and keep fringing capacitance consistent for stable threshold calibration. A solid ground plane under the 28-SSOP is strongly recommended.
Three frequent mistakes: (1) treating the device as 5V-tolerant - VDD max is 3.6V, so 5V UART or sensor outputs need level shifting; (2) forgetting that PPS must be configured in firmware before UART/LIN or remapped peripherals function - unconfigured pins default away from digital peripherals; (3) underestimating FLASH - 16KB fills quickly with LIN stacks and FOC math, so check the compiler memory map early and step up to the pin-compatible DSPIC33FJ32MC102-I/SS rather than squeezing late-stage features.
규정 준수 정보
Package described as lead-free in third-party datasheet listings for the family. This standard part is not AEC-Q100 qualified; it is an industrial-grade (-I) device. Confirm full RoHS/REACH certificates via the Microchip product page.
