EPC4QI100 - 4Mb Enhanced Configuration PROM, 100-PQFP | Intel (Altera)
부품 번호: EPC4QI100 ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $32.5 | $32.50 |
| 10 | $28.75 | $287.50 |
| 100 | $24.95 | $2,495.00 |
| 500 | $22.4 | $11,200.00 |
| 1,000 | $19.85 | $19,850.00 |
EPC4QI100 개요
An enhanced configuration device (ECD) is a specialized non-volatile memory IC paired with a configuration controller that orchestrates the bitstream transfer between the PROM and the target FPGA during power-up. ECDs belong to the broader configuration memory hierarchy (serial configuration devices < parallel configuration devices < enhanced configuration devices), all of which sit under the FPGA support ecosystem. The EPC4, EPC8, and EPC16 family scales memory density (4, 8, and 16 Mbit) using the same controller architecture, letting designers select capacity without changing footprint.
Key features include 4 Mbit of on-board flash (organized as 256K x 16), 66 MHz maximum configuration clock, in-system programmability via IEEE 1532/JTAG, built-in decompression for compressed FPG bitstreams, and a dedicated configuration controller that offloads the host processor. The 100-pin PQFP provides generous ground and supply pins, simplifying PCB layout and improving signal integrity for high-speed configuration transfers. Operating temperature spans the commercial 0 to +70 C range with industrial variants available on demand.
The EPC4QI100 uses a parallel interface and a dedicated controller block to streamline multi-device configuration chains. Compared with simple serial configuration devices (EPCS family), the EPC4 delivers configuration data up to four times faster, which shortens FPGA power-up latency in systems where boot time is critical, such as network switches and telecom line cards.
Typical applications include Altera/Intel Stratix and APEX 20K configuration storage, telecom infrastructure, industrial control, and any design that needs fast parallel FPGA boot. Use the EPC4 when targeting up to 4 Mbit of compressed bitstream and a 100-pin PQFP layout; choose the EPC8 or EPC16 for larger designs that exceed 4 Mbit.
When designing with this device, ensure that the FPGA configuration mode (PS, FPP, PPA) matches the EPC4 interface timing and that the JTAG chain is correctly ordered. Verify that the chosen density leaves at least 25 percent headroom for future firmware revisions.
This page synthesizes distributor pricing, drop-in alternatives from the Altera ECD family, and practical configuration-design notes not found in the manufacturer datasheet.
드롭인 대체품: EPC4QI100 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: EPC4QI100 (동일 폼 팩터 및 풋프린트) — 차이점: Memory Size, Memory Type, Operating Temperature, Interface, Package.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
EPC4QI100N
✅ 드롭인✓ 재고 있음
$10.4 / 개
데이터시트 보기 →EPC4QC100
✅ 드롭인✓ 재고 있음
$11.4 / 개
데이터시트 보기 →EPC8QC100
✅ 드롭인✓ 재고 있음
$17.5 / 개
데이터시트 보기 →EPC16QC100
✅ 드롭인✓ 재고 있음
$14.95 / 개
데이터시트 보기 →EPC8QC100N
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$9.1 / 개
데이터시트 보기 →EPC16QI100
✅ 드롭인✓ 재고 있음
$15.4 / 개
데이터시트 보기 →EPC4QI100 최대 정격 & 전기적 특성
| 메모리 유형 | Non-volatile Flash Configuration PROM |
| 메모리 크기 | 4 Mbit (256K x 16) |
| 인터페이스 | Parallel (16-bit) |
| Configuration Clock (max) | 66 MHz |
| 공급 전압 | 3.3 V |
| In-System Programmability | Yes (IEEE 1532 / JTAG) |
| Compression Support | Yes (decompression built into controller) |
| Configuration Controller | Integrated |
| 패키지 | 100-pin PQFP (PQFP-100, 20 x 14 mm) |
| 실장 유형 | Surface Mount |
| 동작 온도 | 0 C to +70 C (commercial) |
| Supported FPGA Families | Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, FLEX 10K |
| MSL 레벨 | 3 |
| RoHS 상태 | Compliant |
| Family | Enhanced Configuration Device (EPC4/EPC8/EPC16) |
EPC4QI100 핀 구성
| 핀 1 | DATA0 — Configuration data bit 0 (LSB) |
| 핀 2 | DATA1 — Configuration data bit 1 |
| 핀 3 | DATA2 — Configuration data bit 2 |
| 핀 4 | DATA3 — Configuration data bit 3 |
| 핀 5 | VCC — 3.3 V supply |
| 핀 6 | DATA4 — Configuration data bit 4 |
| 핀 7 | DATA5 — Configuration data bit 5 |
| 핀 8 | DATA6 — Configuration data bit 6 |
| 핀 9 | DATA7 — Configuration data bit 7 |
| 핀 10 | GND — Ground |
| 핀 11 | DATA8 — Configuration data bit 8 |
| 핀 12 | DATA9 — Configuration data bit 9 |
| 핀 13 | DATA10 — Configuration data bit 10 |
| 핀 14 | DATA11 — Configuration data bit 11 |
| 핀 15 | DATA12 — Configuration data bit 12 |
| 핀 16 | DATA13 — Configuration data bit 13 |
| 핀 17 | DATA14 — Configuration data bit 14 |
| 핀 18 | DATA15 — Configuration data bit 15 (MSB) |
| 핀 19 | VCC — 3.3 V supply |
| 핀 20 | GND — Ground |
| 핀 21 | DCLK — Configuration clock output to FPGA |
| 핀 22 | GND — Ground |
| 핀 23 | nCONFIG — Configuration control from FPGA/system |
| 핀 24 | nSTATUS — Status signal to FPGA |
| 핀 25 | nCS — Chip select input |
| 핀 26 | OE — Output enable input |
| 핀 27 | VCC — 3.3 V supply |
| 핀 28 | TCK — JTAG test clock |
| 핀 29 | TMS — JTAG test mode select |
| 핀 30 | TDI — JTAG test data in |
| 핀 31 | TDO — JTAG test data out |
| 핀 32 | GND — Ground |
| 핀 33 | VCC — 3.3 V supply |
| 핀 34 | NC — Not connected (per datasheet) |
| 핀 35 | NC — Not connected (per datasheet) |
| 핀 36 | NC — Not connected (per datasheet) |
| 핀 37 | NC — Not connected (per datasheet) |
| 핀 38 | NC — Not connected (per datasheet) |
| 핀 39 | NC — Not connected (per datasheet) |
| 핀 40 | NC — Not connected (per datasheet) |
| 핀 41 | NC — Not connected (per datasheet) |
| 핀 42 | NC — Not connected (per datasheet) |
| 핀 43 | NC — Not connected (per datasheet) |
| 핀 44 | NC — Not connected (per datasheet) |
| 핀 45 | NC — Not connected (per datasheet) |
| 핀 46 | NC — Not connected (per datasheet) |
| 핀 47 | NC — Not connected (per datasheet) |
| 핀 48 | NC — Not connected (per datasheet) |
| 핀 49 | NC — Not connected (per datasheet) |
| 핀 50 | GND — Ground |
| 핀 51 | NC — Not connected (per datasheet) |
| 핀 52 | NC — Not connected (per datasheet) |
| 핀 53 | NC — Not connected (per datasheet) |
| 핀 54 | NC — Not connected (per datasheet) |
| 핀 55 | NC — Not connected (per datasheet) |
| 핀 56 | NC — Not connected (per datasheet) |
| 핀 57 | NC — Not connected (per datasheet) |
| 핀 58 | NC — Not connected (per datasheet) |
| 핀 59 | NC — Not connected (per datasheet) |
| 핀 60 | NC — Not connected (per datasheet) |
| 핀 61 | NC — Not connected (per datasheet) |
| 핀 62 | NC — Not connected (per datasheet) |
| 핀 63 | NC — Not connected (per datasheet) |
| 핀 64 | NC — Not connected (per datasheet) |
| 핀 65 | NC — Not connected (per datasheet) |
| 핀 66 | NC — Not connected (per datasheet) |
| 핀 67 | GND — Ground |
| 핀 68 | VCC — 3.3 V supply |
| 핀 69 | NC — Not connected (per datasheet) |
| 핀 70 | NC — Not connected (per datasheet) |
| 핀 71 | NC — Not connected (per datasheet) |
| 핀 72 | NC — Not connected (per datasheet) |
| 핀 73 | NC — Not connected (per datasheet) |
| 핀 74 | NC — Not connected (per datasheet) |
| 핀 75 | NC — Not connected (per datasheet) |
| 핀 76 | NC — Not connected (per datasheet) |
| 핀 77 | NC — Not connected (per datasheet) |
| 핀 78 | NC — Not connected (per datasheet) |
| 핀 79 | NC — Not connected (per datasheet) |
| 핀 80 | NC — Not connected (per datasheet) |
| 핀 81 | NC — Not connected (per datasheet) |
| 핀 82 | NC — Not connected (per datasheet) |
| 핀 83 | NC — Not connected (per datasheet) |
| 핀 84 | VCC — 3.3 V supply |
| 핀 85 | NC — Not connected (per datasheet) |
| 핀 86 | NC — Not connected (per datasheet) |
| 핀 87 | NC — Not connected (per datasheet) |
| 핀 88 | NC — Not connected (per datasheet) |
| 핀 89 | NC — Not connected (per datasheet) |
| 핀 90 | NC — Not connected (per datasheet) |
| 핀 91 | NC — Not connected (per datasheet) |
| 핀 92 | NC — Not connected (per datasheet) |
| 핀 93 | NC — Not connected (per datasheet) |
| 핀 94 | NC — Not connected (per datasheet) |
| 핀 95 | NC — Not connected (per datasheet) |
| 핀 96 | NC — Not connected (per datasheet) |
| 핀 97 | GND — Ground |
| 핀 98 | VCC — 3.3 V supply |
| 핀 99 | NC — Not connected (per datasheet) |
| 핀 100 | GND — Ground |
일반적인 애플리케이션
EPC4QI100 적합 용도: 6 애플리케이션s: Altera Stratix FPGA Configuration Storage, APEX 20K / APEX II FPGA Boot Memory, Mercury / ACEX 1K / FLEX 10K Legacy FPGA Support, Telecom Line Cards and Network Switches, Industrial Control and Test Equipment, Legacy Avionics and Defense Backplanes.
Altera Stratix FPGA Configuration Storage
The EPC4QI100 stores up to 4 Mbit of compressed Stratix configuration bitstream and streams it through a 16-bit parallel interface at 66 MHz during power-up, enabling Stratix FPGAs to enter user mode in well under 100 ms even with full design compression. Its dedicated configuration controller offloads the host CPU, and the 100-pin PQFP provides ample GND and VCC pins for low-noise configuration of multi-gigabit transceivers on the Stratix device. Designers should pair it with an external clock source and verify that the JTAG chain order matches the FPGA before sealing the BOM.
추천
APEX 20K / APEX II FPGA Boot Memory
For legacy APEX 20K and APEX II designs, the EPC4QI100 provides the parallel-configuration storage required by these multi-device, high-logic-density FPGAs. The integrated controller handles the APEX 16-bit passive parallel asynchronous (PPA) configuration scheme, eliminating the need for an external CPLD to glue the PROM to the FPGA. Using the EPC4QI100 keeps the BOM simple for industrial PLC and machine-vision cards that still ship with APEX 20K FPGAs.
추천
Mercury / ACEX 1K / FLEX 10K Legacy FPGA Support
The EPC4QI100 supports the older Mercury, ACEX 1K, and FLEX 10K FPGA families through its parallel passive configuration interface, allowing long-lifecycle industrial and aerospace programs to keep using proven FPGAs. The 4 Mbit capacity fits most ACEX 1K and FLEX 10K designs after compression, while the same 100-pin PQFP footprint lets engineers replace a failing EPC1 or EPC2 without reworking the PCB. Field upgrades use the IEEE 1532 JTAG interface, supporting in-system reprogramming without removing the device.
추천
Telecom Line Cards and Network Switches
In telecom line cards where FPGA boot time is part of the carrier-grade startup budget, the EPC4QI100's 66 MHz parallel configuration minimizes power-on-to-user-mode latency. The device streams configuration data into Altera FPGAs through 16-bit DATA lines, supporting fast passive parallel configuration without burdening the system controller. Its commercial 0-70 C operating range is sufficient for climate-controlled central-office environments, while the wide pin count gives excellent signal integrity for long PCB traces.
추천
Industrial Control and Test Equipment
Industrial PLCs, motion controllers, and automated test equipment rely on the EPC4QI100 to boot Altera FPGAs deterministically after power-up. The integrated controller simplifies firmware bring-up by handling the entire configuration handshake (nCONFIG, nSTATUS, nCS, OE) without host intervention, and the 100-pin PQFP package simplifies hand-solder rework during prototyping. For long-life industrial designs, the EPC4QI100N Pb-free variant supports modern lead-free reflow profiles.
추천
Legacy Avionics and Defense Backplanes
Long-life avionics and defense programs that built around Altera APEX II and FLEX 10K FPGAs continue to use the EPC4QI100 as their configuration memory because of its mature, well-documented silicon and long-term support contracts. Its parallel 16-bit interface delivers deterministic configuration even on backplanes where serial configuration devices can suffer from signal-integrity issues. Obsolescence risk is mitigated by stocking spare EPC4QI100N Pb-free variants as drop-in equivalents.
추천
추천 제품 요약
엔지니어링 참조 데이터: EPC4QI100 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | EPC4QI100N | EPC4QC100 | EPC8QC100 | EPC16QC100 | EPC8QC100N | EPC16QI100 |
|---|---|---|---|---|---|---|---|
| Brand | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) |
| Package | 100-pin PQFP (20 x 14 mm) | 100-pin PQFP - same | 100-pin PQFP - same | 100-pin PQFP - same | 100-pin PQFP - same | 100-pin PQFP - same | 100-pin PQFP - same |
| Memory Size | 4 Mbit | 4 Mbit (same) | 4 Mbit (same) | 8 Mbit (+100%) | 16 Mbit (+300%) | 8 Mbit (+100%) | 16 Mbit (+300%) |
| Configuration Clock (max) | 66 MHz | 66 MHz (same) | 66 MHz (same) | 66 MHz (same) | 66 MHz (same) | 66 MHz (same) | 66 MHz (same) |
| Interface | Parallel 16-bit | Parallel 16-bit (same) | Parallel 16-bit (same) | Parallel 16-bit (same) | Parallel 16-bit (same) | Parallel 16-bit (same) | Parallel 16-bit (same) |
| Supply Voltage | 3.3 V | 3.3 V (same) | 3.3 V (same) | 3.3 V (same) | 3.3 V (same) | 3.3 V (same) | 3.3 V (same) |
| RoHS / Lead-Free | Compliant | Pb-free variant | Compliant | Compliant | Compliant | Pb-free variant | Compliant |
| Lifecycle | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
주요 차별점
- Integrated configuration controller eliminates external glue logic (vs EPC1LC20 (legacy 1 Mbit serial configuration PROM))
- Parallel 16-bit interface delivers 4x faster configuration than serial PROMs (vs EPCS16 (16 Mbit serial configuration device))
- Same 100-pin PQFP footprint as EPC8/EPC16 family (vs EPC8QC100)
설계 노트
The EPC4QI100 operates from a single 3.3 V supply and draws a small quiescent current during configuration. Decouple VCC pins (5, 19, 27, 33, 68, 84, 98) with 0.1 uF ceramic capacitors placed as close to the device as possible, and add a bulk 10 uF tantalum or ceramic cap near the package to suppress FPGA inrush currents during configuration. Keep the 3.3 V rail clean because any noise on VCC can corrupt the parallel DATA bus and cause configuration failures.
The 16-bit DATA bus and DCLK lines should be routed as a matched-length group, with trace length matching within +/- 100 mil to avoid setup/hold violations on the target FPGA. Series-terminate each DATA line with 33 ohm resistors near the EPC4QI100 if the configuration trace length exceeds 3 inches. Place a ground guard trace between DATA[0..7] and DATA[8..15] to minimize crosstalk, and keep the JTAG chain (TCK/TMS/TDI/TDO) electrically isolated from the parallel DATA bus.
Do not exceed the 66 MHz maximum DCLK frequency, and confirm the FPGA configuration mode (FPP/PPA/PS) matches the EPC4QI100 interface timing. Verify JTAG chain order in the Quartus programmer before sealing the BOM, and ensure the EPC4 bitstream size leaves at least 25 percent headroom for future firmware revisions. Because the EPC4QI100 is obsolete, consider migrating new designs to active EPCQ or EPCQ-L serial configuration devices that support Cyclone, Arria, and Stratix 10 families.
Place the EPC4QI100 within 2 inches of the target FPGA to keep DCLK and DATA traces short and matched. Use a continuous ground plane under the PQFP-100 device to provide low-impedance return paths for the parallel DATA bus. Route JTAG signals (TCK, TMS, TDI, TDO) to a dedicated test header that is accessible after board assembly for in-system programming and boundary-scan testing.
규정 준수 정보
RoHS and lead-free compliance per Altera/Intel product page. EPC4QI100N is the Pb-free variant with identical pinout. Halogen-free status not explicitly stated in provided data and is recorded as 'unknown'. The part is classified obsolete by Intel; design teams should consider EPCQ-family active configuration devices for new designs.
