GRM1885C1H151JA01D - 150pF 50V C0G/NP0 0603 MLCC | Murata
부품 번호: GRM1885C1H151JA01D ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0.1 | $0.10 |
| 10 | $0.062 | $0.62 |
| 100 | $0.029 | $2.90 |
| 500 | $0.021 | $10.50 |
| 1,000 | $0.016 | $16.00 |
| 4,000 | $0.012 | $48.00 |
GRM1885C1H151JA01D 개요
A multilayer ceramic capacitor (MLCC) is a surface-mount passive component constructed from alternating layers of ceramic dielectric and metal electrodes, sintered into a monolithic block with external terminations. MLCCs are the most widely manufactured capacitor type globally, serving general-purpose filtering, decoupling, bypass, and coupling roles across nearly every electronic system. C0G (also designated NP0) is a Class 1 dielectric, meaning its capacitance is essentially unaffected by temperature, voltage, frequency, or time - making C0G parts the preferred choice for resonant circuits, precision timing, and analog signal paths where stability matters more than volumetric efficiency.
Key features include ±5% capacitance tolerance (J code), 50 VDC rated voltage, C0G/NP0 temperature characteristic (0 ±30 ppm/°C), and a 0603 EIA case size. The C0G dielectric ensures minimal capacitance change with DC bias, no piezo-electric noise, and Q factor above 1000 at 1 MHz - ideal for RF and high-frequency analog circuits. The standard 0603 footprint is compatible with high-volume pick-and-place assembly lines.
The GRM1885C1H151JA01D utilizes a nickel-barrier tin (NiSn) termination finish for lead-free reflow soldering compatibility, with a 1.0 mm maximum chip thickness suitable for standard 0603 land patterns. The part is RoHS compliant and qualified to Murata's GRM series reliability standards for general-purpose commercial and industrial applications.
Typical applications include RF signal coupling and bypass in transceivers, precision timing circuits and crystal load capacitors, analog filter networks, snubber circuits in switch-mode power supplies, and general-purpose decoupling in microcontroller and DSP designs. Its small size and stable C0G dielectric also make it suitable for sensor conditioning, instrumentation amplifiers, and oscillator networks.
When designing with this part, confirm that the application operates within the 50 VDC rating and that the PCB land pattern follows IPC-7351 0603 (1608 metric) guidelines. For applications requiring tighter capacitance tolerance (e.g., ±1% or ±2%), specify a C0G part with F or G tolerance code rather than the standard J (±5%) code.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design considerations not consolidated on the manufacturer datasheet alone, including engineering guidance for C0G dielectric selection and 0603 land-pattern layout per IPC-7351.
드롭인 대체품: GRM1885C1H151JA01D — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
GRM1885C1H151JA01L
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
GRM1885C1H151GA01D
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
GRM1885C2H151JA01D
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
CGA2B2C0G1H151J
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
CL10B151JB8NNNC
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
CC0603JRNPO9BN151
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
GRM1885C1H151JA01D 최대 정격 & 전기적 특성
| Capacitance | 150 pF |
| Capacitance Tolerance | ±5% |
| Rated Voltage (VDC) | 50 V |
| Dielectric / Temperature Characteristic | C0G / NP0 (0 ±30 ppm/°C) |
| EIA Case Size | 0603 (1608 Metric) |
| Length | 1.6 mm |
| Width | 0.8 mm |
| Thickness (Max) | 0.8 mm |
| 동작 온도 범위 | -55 °C to +125 °C |
| Termination Finish | Ni/Sn (nickel barrier, tin plated) |
| 실장 유형 | Surface Mount (SMT) |
| Packaging | Paper Tape & Reel (T&R), 4,000 pcs per reel |
| RoHS Compliance | Compliant |
| REACH Compliance | Compliant |
| Lead-Free Reflow Compatible | Yes (260 °C peak) |
GRM1885C1H151JA01D 0603 (1608 metric) 핀 구성 가이드
GRM1885C1H151JA01D(0603 (1608 metric) 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: GRM1885C1H151JA01D.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
GRM1885C1H151JA01D 적합 용도: 6 애플리케이션s: RF Signal Coupling / Bypass, Crystal Oscillator Load Capacitor, Analog Filter Networks (RC / LC Active Filters), ADC Reference / Precision Decoupling, Snubber Capacitor for Switching Power Supplies, Sensor Signal Conditioning & Instrumentation.
RF Signal Coupling / Bypass
The GRM1885C1H151JA01D's 150 pF C0G/NP0 capacitance provides stable AC coupling and DC blocking in RF signal paths up through VHF/UHF bands without distorting resonance. C0G dielectric (0 ±30 ppm/°C) means the 150 pF value does not drift with temperature, eliminating gain or matching drift in receiver front ends, antenna tuners, and low-noise amplifiers. The 0603 footprint is well suited for 50 Ω microstrip RF layouts where compact size and predictable parasitic inductance (~1 nH) support sub-GHz filtering. Placed in series between LNA stages or at mixer IF ports, it provides DC isolation while passing RF signals cleanly. Compared to X7R or X5R 150 pF parts, the GRM1885C1H151JA01D avoids piezo-electric ringing and DC-bias capacitance loss, making it the preferred choice for narrowband filters, image-reject mixers, and oscillator tank circuits.
추천
Crystal Oscillator Load Capacitor
The GRM1885C1H151JA01D is widely used as the external load capacitor on Pierce oscillator circuits with quartz crystals, where it sets the load resonance frequency together with the crystal's motional capacitance. C0G/NP0 dielectric guarantees the 150 pF load value is unaffected by DC bias or temperature, ensuring oscillator frequency stability over -40 °C to +85 °C commercial and +125 °C industrial ranges. Compared to Class 2 dielectrics, C0G eliminates the ±15% tolerance stack-up with the crystal's own series tolerance, simplifying frequency-accuracy budgeting. The 0603 case size is a standard reference for IC manufacturers' recommended crystal load networks, including microcontrollers with integrated oscillator drivers (e.g., STM32, EFM32, MSP430 families). Place symmetrically on both XTAL pins with short PCB traces to minimize parasitic capacitance.
추천
Analog Filter Networks (RC / LC Active Filters)
The GRM1885C1H151JA01D's stable 150 pF capacitance makes it ideal as the C element in Sallen-Key, multiple-feedback, and biquad active filter topologies operating from audio through low-MHz signal bands. C0G dielectric preserves filter cutoff frequency accuracy over temperature - critical for anti-aliasing filters in front of ADCs, audio crossovers, and instrumentation signal conditioning where filter response must remain flat. With ±5% tolerance and low ESR, the part pairs well with 1% metal-film or thin-film resistors (e.g., E96 series) to achieve predictable filter Q and ripple behavior. Designers should bias this capacitor into a low-impedance op-amp output stage to prevent voltage coefficient effects, though C0G parts are far less sensitive to this than X7R/X5R alternatives.
추천
ADC Reference / Precision Decoupling
Place the GRM1885C1H151JA01D on precision analog reference pins of SAR ADCs, sigma-delta converters, and voltage references to filter high-frequency noise without distorting DC accuracy. C0G dielectric ensures no capacitance loss under the reference DC bias voltage, preserving the reference pin's noise-filtering effectiveness across the full 5 V to 2.5 V common reference range. For high-resolution 16-bit and 24-bit ADCs, the absence of dielectric absorption and piezo-electric noise in C0G translates directly to cleaner code-edge transitions. The 0603 case size fits beneath most SOIC/MSOP op-amp layouts, allowing tight placement next to the reference pin with a 0.1 µF X7R bulk-decoupling capacitor in parallel for broadband noise suppression.
추천
Snubber Capacitor for Switching Power Supplies
The GRM1885C1H151JA01D serves as a compact RC snubber across switching nodes in flyback, buck, and boost converters where small capacitance and tight tolerance are required to damp high-frequency ringing. C0G/NP0 dielectric withstands the high dV/dt and high-frequency current pulses that would degrade Class 2 dielectrics through piezo-electric effects or piezoelectric ringing. With 50 V rating, this part suits 12 V and 24 V bus snubbers in industrial and telecom DC-DC converters. Its 150 pF value is commonly used across MOSFET drain-source or rectifier junctions to suppress ringing above 50 MHz while not loading the switching waveform at fundamental frequency. Designers should select ESR values by pairing with low-inductance 10-100 Ω resistors.
추천
Sensor Signal Conditioning & Instrumentation
The GRM1885C1H151JA01D is well suited as a stable C0G filter capacitor in front-end signal conditioning for pressure sensors, temperature sensors, and bridge-type transducers where capacitance stability is critical for accurate gain/phase response. Its 150 pF value is appropriate for low-pass filter corner frequencies in the 1-100 kHz range when paired with 10 kΩ to 100 kΩ source impedances, providing EMI rejection without introducing thermal drift into the conditioned signal. In instrumentation amplifier front ends, the C0G dielectric eliminates the charge injection and dielectric absorption that would otherwise inject microvolt-level errors into the amplified sensor output. The 0603 footprint supports compact multi-channel sensor PCB layouts common in industrial IoT and medical instrumentation.
추천
추천 제품 요약
엔지니어링 참조 데이터: GRM1885C1H151JA01D — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | GRM1885C1H151JA01L | GRM1885C1H151GA01D | GRM1885C2H151JA01D | CGA2B2C0G1H151J | CL10B151JB8NNNC | CC0603JRNPO9BN151 |
|---|---|---|---|---|---|---|---|
| Package | 0603 (1608 Metric) | 0603 (1608 Metric) - same | 0603 (1608 Metric) - same | 0603 (1608 Metric) - same | 0603 (1608 Metric) - same | 0603 (1608 Metric) - same | 0603 (1608 Metric) - same |
| Brand | Murata | Murata - same | Murata - same | Murata - same | TDK | Samsung Electro-Mechanics | Yageo |
| Capacitance | 150 pF | 150 pF | 150 pF | 150 pF | 150 pF | 150 pF | 150 pF |
| Capacitance Tolerance | ±5% (J) | ±5% (J) | ±2% (G) - tighter | ±5% (J) | ±5% (J) | ±5% (J) | ±5% (J) |
| Rated Voltage | 50 V | 50 V | 50 V | 100 V - higher | 50 V | 50 V | 50 V |
| Dielectric | C0G / NP0 | C0G / NP0 | C0G / NP0 | C0G / NP0 | C0G / NP0 | C0G / NP0 | C0G / NPO |
| Operating Temperature | -55 °C to +125 °C | -55 °C to +125 °C | -55 °C to +125 °C | -55 °C to +125 °C | -55 °C to +125 °C | -55 °C to +125 °C | -55 °C to +125 °C |
| RoHS / Lead-Free | Compliant / Yes | Compliant / Yes | Compliant / Yes | Compliant / Yes | Compliant / Yes | Compliant / Yes | Compliant / Yes |
주요 차별점
- Cross-brand standardization to EIA C0G 0603 (vs CGA2B2C0G1H151J (TDK))
- Higher-voltage drop-in upgrade path within same family (vs GRM1885C2H151JA01D (100 V))
- Tighter tolerance option without changing footprint (vs GRM1885C1H151GA01D (±2%))
설계 노트
Use an 0603 (1608 metric) land pattern per IPC-7351 with two 0.9-1.0 mm × 0.9-1.0 mm pads on 1.5 mm pitch. Place the part in a single, unbroken ground or signal plane cutout and minimize trace length to reduce parasitic inductance. For RF applications, keep traces to <1 mm and use a continuous ground pour on the opposite PCB layer directly beneath the capacitor to maintain a controlled-impedance environment.
Do not substitute an X7R or X5R 150 pF 0603 part in C0G applications where temperature stability, voltage coefficient, or low-loss is critical - X7R parts can lose 30-80% of nominal capacitance under DC bias at higher voltage ratings. Verify the dielectric code (C0G vs X7R vs X5R) on the packaging label before placement, as 0603 marking codes are abbreviated. Confirm the operating voltage never exceeds 50 VDC, including any transient spikes.
For noise-sensitive applications such as ADC reference decoupling or crystal oscillator loads, route the capacitor directly to the IC pin with the shortest possible trace and use a via-in-pad or stitched ground via array to minimize parasitic inductance. Place any bulk decoupling capacitor (e.g., 0.1 µF X7R) within 1-2 mm of the C0G capacitor to form a broadband filter network. Avoid routing noisy digital signals adjacent to C0G filter capacitors on RF or analog signal layers.
규정 준수 정보
RoHS and REACH compliant per Murata product page. Lead-free NiSn termination suitable for 260 °C peak reflow per JEDEC J-STD-020. AEC-Q100 not applicable - this is a general-purpose commercial/industrial MLCC; for automotive-grade C0G 0603 150 pF parts, request Murata's automotive-qualified GRM series variants.
