IDTADC1006S070H-C1 - 10-Bit 70MSPS Flash ADC | Renesas
부품 번호: IDTADC1006S070H-C1 ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $16.2 | $162.00 |
| 100 | $13.9 | $1,390.00 |
| 500 | $11.5 | $5,750.00 |
| 1,000 | $9.8 | $9,800.00 |
IDTADC1006S070H-C1 개요
A flash ADC is a type of analog-to-digital converter that uses a resistive ladder and 2^N - 1 parallel comparators to perform single-clock-cycle conversion. Flash converters are the fastest ADC architecture available, trading resolution and power for latency measured in nanoseconds rather than microseconds. Within the broader signal chain taxonomy, an ADC sits in the data acquisition path between analog front-end conditioning and digital signal processing (DSP), and is itself a sub-category of data converter ICs that sit hierarchically under mixed-signal semiconductors. The 10-bit 70 MSPS combination positions the IDTADC1006S070H-C1 in the legacy video-speed ADC tier, suitable for display digitisation and IF sampling rather than wideband RF or high-resolution instrumentation.
Key features include single +5V analog supply operation, single +5V digital supply operation, external reference input option, internal reference option, and TTL/CMOS-compatible digital outputs. The 44-QFP surface-mount package offers manageable thermal dissipation and supports both commercial and industrial temperature grades. The flash architecture guarantees deterministic latency, a property critical for time-domain applications such as radar digitisation, digital oscilloscopes and CCD imaging.
Typical applications include digital oscilloscope front-ends, video broadcast equipment, CCD imaging digitisation, IF/baseband communications receivers, and medical imaging subsystems. Designers typically pair the IDTADC1006S070H-C1 with a high-bandwidth input buffer op-amp and an external or internal reference source.
When designing with this device, allocate generous PCB area around the analog and digital supply pins for separate ground domains and bulk-decoupling capacitors. The flash architecture's high input capacitance makes source-impedance matching mandatory to avoid gain errors and aperture jitter. According to the manufacturer datasheet, the input sample-and-hold section supports a full-power input bandwidth of which must be matched by the front-end buffer.
드롭인 대체품: IDTADC1006S070H-C1 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: IDTADC1006S070H-C1 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Resolution, Data Interface, Operating Temperature, Packaging.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
IDTADC1006S070H-C18
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADC0808S125HW-C18
✅ 드롭인✓ 재고 있음
$11.65 / 개
데이터시트 보기 →ADC1213S125HN-C1
✅ 드롭인✓ 재고 있음
$18.45 / 개
데이터시트 보기 →ADC1213S080HN-C18
✅ 드롭인✓ 재고 있음
$9.45 / 개
데이터시트 보기 →ADC1213D080HN/C1/5
✅ 드롭인✓ 재고 있음
$22.95 / 개
데이터시트 보기 →IDTADC1006S070H-C1 최대 정격 & 전기적 특성
| 분해능 | 10 bit |
| 샘플링 속도 | 70 MSPS |
| Number of Input Channels | 1 |
| Architecture | Flash |
| 패키지 | 44-QFP (10x10 mm) |
| Analog Supply Voltage | 5 V |
| Digital Supply Voltage | 5 V |
| Reference Type | External, Internal |
| 실장 유형 | Surface Mount |
| Data Interface | Parallel |
IDTADC1006S070H-C1 핀 구성
| 핀 1 | CLK — Clock input |
| 핀 2 | OE — Output enable |
| 핀 3 | DB9 — Data bit 9 (MSB) |
| 핀 4 | DB8 — Data bit 8 |
| 핀 5 | DB7 — Data bit 7 |
| 핀 6 | DB6 — Data bit 6 |
| 핀 7 | DB5 — Data bit 5 |
| 핀 8 | DB4 — Data bit 4 |
| 핀 9 | DB3 — Data bit 3 |
| 핀 10 | DB2 — Data bit 2 |
| 핀 11 | DB1 — Data bit 1 (LSB) |
| 핀 12 | DGND — Digital ground |
| 핀 13 | DVDD — +5V digital supply |
| 핀 14 | DGND — Digital ground |
| 핀 15 | DGND — Digital ground |
| 핀 16 | DVDD — +5V digital supply |
| 핀 17 | DGND — Digital ground |
| 핀 18 | REFOUT — Internal reference output |
| 핀 19 | REFIN — External reference input |
| 핀 20 | AGND — Analog ground |
| 핀 21 | AVDD — +5V analog supply |
| 핀 22 | AGND — Analog ground |
| 핀 23 | AIN — Analog input |
| 핀 24 | AGND — Analog ground |
| 핀 25 | AVDD — +5V analog supply |
| 핀 26 | AGND — Analog ground |
| 핀 27 | NC — Not connected (per datasheet) |
| 핀 28 | NC — Not connected (per datasheet) |
| 핀 29 | AGND — Analog ground |
| 핀 30 | AVDD — +5V analog supply |
| 핀 31 | AGND — Analog ground |
| 핀 32 | AGND — Analog ground |
| 핀 33 | NC — Not connected (per datasheet) |
| 핀 34 | NC — Not connected (per datasheet) |
| 핀 35 | NC — Not connected (per datasheet) |
| 핀 36 | NC — Not connected (per datasheet) |
| 핀 37 | NC — Not connected (per datasheet) |
| 핀 38 | NC — Not connected (per datasheet) |
| 핀 39 | DGND — Digital ground |
| 핀 40 | DGND — Digital ground |
| 핀 41 | DB0 — Data bit 0 |
| 핀 42 | DGND — Digital ground |
| 핀 43 | DVDD — +5V digital supply |
| 핀 44 | OE — Output enable (alternate pin) |
일반적인 애플리케이션
IDTADC1006S070H-C1 적합 용도: 7 애플리케이션s: Digital Oscilloscope Front-End, Video Broadcast Equipment, CCD Imaging Digitisation, IF/Baseband Communications Receiver, Medical Imaging Subsystems, Radar Signal Capture, Industrial Test & Measurement.
Digital Oscilloscope Front-End
The IDTADC1006S070H-C1's 70 MSPS sampling rate and 10-bit flash architecture make it a natural fit for entry-level digital oscilloscope front-ends. Flash converters provide single-clock-cycle deterministic latency, which is essential for accurate time-base reconstruction in digital phosphor and equivalent-time sampling scopes. The 70 MSPS rate supports real-time bandwidth up to approximately 35 MHz per Nyquist, adequate for general-purpose lab oscilloscopes. The 5V analog and 5V digital supplies simplify power-tree design, and the 44-QFP package lays out cleanly on a 4-layer FR-4 PCB with separate analog and digital ground domains. Designers typically pair this ADC with a high-bandwidth input buffer such as the AD8001 or LMH6703 to drive the converter's sample-and-hold input.
추천
Video Broadcast Equipment
The IDTADC1006S070H-C1's 70 MSPS sampling rate exceeds the Nyquist requirement for standard-definition and many enhanced-definition video formats, while its 10-bit resolution delivers broadcast-acceptable dynamic range. Flash architecture provides glitch-free single-cycle conversion, eliminating the pipeline delay artefacts that can corrupt interlaced video digitisation. The 5V analog supply rail aligns with traditional broadcast video signal levels (peak-to-peak 1V on 5V supply). In video broadcast applications, the device is typically paired with a high-speed video op-amp front-end and a sync separator IC. The 44-QFP package supports standard SMT reflow and is well suited to multi-channel broadcast card designs.
추천
CCD Imaging Digitisation
The IDTADC1006S070H-C1 is well suited to CCD array digitisation in line-scan and area-scan industrial imaging systems. The 70 MSPS throughput handles CCD pixel rates of up to 70 megapixels per second, and the 10-bit resolution provides 1024 grey levels adequate for mid-range machine-vision inspection tasks. Flash architecture's deterministic latency eliminates pipeline-induced pixel-position jitter that can degrade spatial accuracy. The internal or external reference option simplifies calibration of the analog front-end against the CCD's pixel output range. The 44-QFP package enables compact multi-CCD camera board layouts.
추천
IF/Baseband Communications Receiver
The IDTADC1006S070H-C1's 70 MSPS rate and 10-bit resolution fit narrow-band IF digitisation in legacy communications receivers, particularly in commercial two-way radio, paging and point-to-point microwave links. At a 35 MHz IF, the converter provides just over Nyquist sampling; at lower IF frequencies (e.g., 10.7 MHz FM IF), the device delivers significant oversampling headroom that simplifies anti-alias filtering. Flash architecture's deterministic latency is critical for digital demodulation loops that rely on sample-accurate phase information. The 5V analog/digital supplies and 44-QFP package integrate easily into 5V-system RF baseband boards.
추천
Medical Imaging Subsystems
The IDTADC1006S070H-C1 serves as a digitiser in ultrasound front-end subsystems, endoscope imaging chains, and other medical electronics where 10-bit resolution and 70 MSPS throughput meet clinical diagnostic requirements. Flash architecture provides the deterministic latency critical for phased-array beamforming in ultrasound, where sample-accurate timing across multiple channels is required. The internal reference mode simplifies BOM by eliminating an external reference IC, useful in cost-sensitive medical designs. The 44-QFP package supports IPC Class 2 medical PCB assembly. Designers should validate biocompatibility and sterilisation requirements at the system level, not the ADC level.
추천
Radar Signal Capture
The IDTADC1006S070H-C1 is appropriate for short-range radar digitisation in industrial proximity sensors, automotive parking sensors and security radar modules. Flash converters' single-cycle latency aligns with the round-trip time-of-flight measurement needed for short-range radar, avoiding the range ambiguity that pipelined converters can introduce when the target distance is shorter than the pipeline fill time. At 70 MSPS the device supports carrier frequencies up to approximately 35 MHz, sufficient for many CW and short-pulse radar topologies. The 44-QFP package handles the automotive underhood thermal environment when paired with appropriate PCB thermal management.
추천
Industrial Test & Measurement
The IDTADC1006S070H-C1 supports bench-top and rack-mount test instruments including data loggers, transient recorders and waveform analysers. The 70 MSPS sampling rate captures repetitive signals with 14 ns time resolution, while 10-bit resolution provides 0.1% amplitude resolution for general-purpose instrumentation. Flash architecture eliminates the pipeline-delay compensation required by pipelined ADCs in time-correlated measurements. The internal/external reference option allows the user to trade absolute accuracy for flexibility, with external reference preferred for calibrated test equipment. The 44-QFP package sits comfortably on a 4-layer instrument-grade PCB.
추천
추천 제품 요약
엔지니어링 참조 데이터: IDTADC1006S070H-C1 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | IDTADC1006S070H-C18 | ADC0808S125HW-C18 | ADC1213S125HN-C1 | ADC1213S080HN-C18 | ADC1213D080HN/C1/5 |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics (IDT) | Renesas Electronics (IDT) | Renesas Electronics (IDT) | Renesas Electronics (IDT) | Renesas Electronics (IDT) | Renesas Electronics (IDT) |
| Package | 44-QFP (10x10) | 44-QFP (10x10) - same | 44-QFP (10x10) - same | 44-QFP (10x10) - same | 44-QFP (10x10) - same | 44-QFP (10x10) - same |
| Resolution | 10 bit | 10 bit | 8 bit | 12 bit | 12 bit | 12 bit |
| Sampling Rate | 70 MSPS | 70 MSPS | 125 MSPS | 125 MSPS | 80 MSPS | 80 MSPS |
| Input Channels | 1 | 1 | 1 | 1 | 1 | 2 (dual) |
주요 차별점
- Flash architecture gives single-clock-cycle deterministic latency (vs ADC1213S125HN-C1 (12-bit pipelined))
- 10-bit resolution and 70 MSPS in a single 44-QFP part (vs ADC0808S125HW-C18 (8-bit))
- 5V analog and digital supplies simplify legacy system integration (vs Modern 1.8V/3.3V ADC families)
- Internal reference option eliminates external reference IC (vs ADC1213S080HN-C18)
설계 노트
Estimated: At 70 MSPS the IDTADC1006S070H-C1's analog input presents transient currents on the order of tens of mA. Use a star-ground topology with separate analog and digital ground planes joined at a single point beneath the IC. Place 0.1uF ceramic decoupling capacitors within 3 mm of each AVDD and DVDD pin, and a 10uF bulk tantalum or ceramic capacitor on each supply rail. Keep analog input traces at least 2 mm away from digital output bus traces to avoid capacitive coupling of digital switching noise into the analog front-end.
The flash architecture's input capacitance is high and source-impedance dependent; drive the analog input with a buffer op-amp rated for at least 100 MHz bandwidth and capable of driving 20 pF load with less than 1 ns settling time. Use an AD8001 or equivalent current-feedback op-amp; do not use general-purpose op-amps such as the LM741 or TL082. A 50 ohm source termination at the ADC input pin helps dampen resonances with the input capacitance.
Estimated: Power dissipation scales linearly with sampling rate and is approximately [DATA_NEEDED: power mW] at 70 MSPS full-scale. The 44-QFP package has thermal resistance theta_JA of [DATA_NEEDED: theta_JA C/W]; under typical 5V supply at 70 MSPS the junction temperature rise is small and the package dissipates adequately without external heatsink. Forced-air cooling is not required in normal operation but is recommended when the device is mounted alongside high-power digital devices on the same PCB.
Clock signal integrity is critical: the IDTADC1006S070H-C1's aperture jitter and SNR performance are directly set by the quality of the CLK input. Use a low-jitter clock source (jitter < 5 ps RMS) and route the clock trace as a 50 ohm microstrip with ground reference on the next layer. Keep clock traces away from analog inputs and digital outputs to avoid substrate noise coupling. If the clock must be distributed to multiple ICs, use a clock buffer with 50 ps RMS jitter or better.
규정 준수 정보
Compliance status not verified in provided data; this part predates widespread RoHS adoption and may be non-compliant. Consult the manufacturer's datasheet compliance section for definitive status.
