ISO1412DWR - 500kbps Full-Duplex 5kVrms Isolated RS-485/RS-422 | Texas Instruments
부품 번호: ISO1412DWR ✓ 활성ISO1412DWR 개요
드롭인 대체품: ISO1412DWR — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ISO1412DWR (동일 폼 팩터 및 풋프린트) — 차이점: Duplex Mode, Operating Temperature Range, Package, Supported Standards.
ISO1410DWR
✅ 드롭인가격 문의
데이터시트 보기 →ISO1410BDWR
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ISO1411DWR
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ISO1412DWR
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →ISO1412DW
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ISO1412DWR 사양
| Product Type | Isolated differential bus transceiver |
| Supported Standards | TIA/EIA RS-485 and TIA/EIA RS-422 |
| 데이터 속도 | 500 kbps |
| Duplex Mode | Full duplex |
| Transmitter Count | 1 |
| Receiver Count | 1 |
| Isolation Voltage | 5 kVrms |
| Supply Voltage Range | 1.71 V to 5.5 V |
| 동작 온도 범위 | -40 °C to 125 °C |
| 패키지 | 16-pin SOIC, DW package |
| 실장 유형 | Surface mount |
| EMC Protection | EMC protected |
| ESD/EFT Protection | High-level bus-pin transient tolerance |
| Galvanic Isolation | Yes |
| Differential Signaling | RS-485 and RS-422 |
ISO1412DWR 16-pin soic, dw package 핀 구성 가이드
ISO1412DWR(16-pin soic, dw package 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: ISO1412DWR.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ISO1412DWR 적합 용도: 6 애플리케이션s: Factory Automation and PLC Fieldbus Links, Motor Drives and Industrial Controls, Photovoltaic Inverter Monitoring, Building Automation and HVAC Equipment, Grid Infrastructure Communication, Fieldbus Gateways and Serial-to-Ethernet Bridges.
Factory Automation and PLC Fieldbus Links
The ISO1412DWR fits isolated factory-automation links that require reliable RS-485 or RS-422 communication at up to 500 kbps. Its 5-kVrms isolation separates the controller interface from the fieldbus, helping reduce ground-loop and high-potential hazards. The full-duplex 1/1 transceiver architecture supports simultaneous transmit and receive paths, while the EMC-focused design is appropriate for industrial cables near motors and switching equipment. Designers should verify the ISO1412 family pinout, termination strategy, and logic-side supply requirements against the manufacturer datasheet before releasing a PLC or remote-I/O board.
추천
Motor Drives and Industrial Controls
The ISO1412DWR is suitable for command and diagnostic links in motor-drive and industrial-control systems where the communications transceiver must withstand electrically noisy environments. Its 500-kbps data rate is suitable for many high-speed serial-control networks, while 5-kVrms isolation provides a substantial barrier between the host controller and bus circuitry. The 16-pin SOIC DW package supports compact, surface-mounted implementation. Engineers should still validate common-mode range, cable length, termination, fail-safe biasing, and transient withstand conditions for the exact industrial network.
추천
Photovoltaic Inverter Monitoring
The ISO1412DWR can connect photovoltaic inverter monitoring electronics to an isolated RS-485 or RS-422 supervisory network. Its 5-kVrms isolation is useful when inverter power stages and external communications equipment may be at different ground potentials, while the EMC protection focus supports operation around high-energy switching converters. The 500-kbps full-duplex capability is adequate for supervisory commands, status reporting, and diagnostic data. Board designers should follow the manufacturer’s isolation and bus-layout guidance, including placement of isolation boundaries, return paths, and protection components.
추천
Building Automation and HVAC Equipment
The ISO1412DWR is appropriate for building-automation controllers and HVAC equipment that exchange RS-485 data with remote sensors, actuators, or supervisory panels. The transceiver combines a 500-kbps data rate, full-duplex operation, and 5-kVrms isolation in a 16-pin SOIC package. Isolation helps maintain communication integrity across systems with long cable runs or different ground references. For dependable deployment, verify the ISO1412 datasheet for logic thresholds, bus termination, receiver fail-safe behavior, and recommended surge-protection arrangements.
추천
Grid Infrastructure Communication
ISO1412DWR devices can provide isolated serial communication between grid-monitoring electronics and field equipment operating across substantial ground-potential differences. Its 500-kbps full-duplex interface is suitable for supervisory telemetry, protection information, and configuration traffic, while the 5-kVrms isolation barrier improves system separation. The EMC-protected construction is relevant in substations and outdoor installations where ESD and electrical-fast-transient disturbances are common. Field engineers must confirm isolation lifetime, working voltage, surge coordination, and cable-routing requirements in addition to the basic bus specification.
추천
Fieldbus Gateways and Serial-to-Ethernet Bridges
The ISO1412DWR fits fieldbus gateways and serial-to-Ethernet bridges that need an isolated industrial-side RS-485 or RS-422 port. At 500 kbps, it accommodates high-speed legacy fieldbus traffic while the full-duplex configuration can support simultaneous control and monitoring. Its 5-kVrms isolation helps keep the gateway’s Ethernet and processing domains separated from the field wiring. For gateway designs, verify bus direction-control logic, termination under the selected network topology, isolation capacitance, and grounding strategy against the manufacturer datasheet.
추천
추천 제품 요약
엔지니어링 참조 데이터: ISO1412DWR — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ISO1410DWR | ISO1410BDWR | ISO1411DWR | ISO1412DW |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-16 (DW) | SOIC-16 (DW) | SOIC-16 (DW) | SOIC-16 (DW) | SOIC-16 (DW) |
주요 차별점
- Verified full-duplex operation (vs ISO1410DWR)
- Explicit 5-kVrms isolation rating (vs ISO1410BDWR)
- Broad specified temperature range (vs ISO1410DWR)
- Verified EMC-focused product positioning (vs ISO1412DW)
설계 노트
Maintain a clear isolation boundary between the logic-side and bus-side networks. Keep the bus traces away from sensitive input, clock, and reference traces, and do not route ground or plane copper across the isolation barrier unless the manufacturer application guidance explicitly permits it. Confirm the exact DW-package pin assignments from the ISO1412 datasheet before fixing the PCB footprint and isolation-clearance requirements.
Do not treat the SOIC-16 package name alone as proof of drop-in compatibility. Before replacing the ISO1412DWR with ISO1410DWR, ISO1410BDWR, or another ISO14xx member, compare every pin, supply rail, logic threshold, isolation rating, driver level, receiver threshold, timing specification, and bus protection parameter. The supplied search excerpts do not provide enough data to guarantee production interchangeability.
Use the manufacturer-recommended bus protection and termination arrangement for the selected RS-485 or RS-422 topology. Place transient-protection components close to the connector and bus pins, keep their return paths short, and avoid long unprotected stubs. The ISO1412 family is described as EMC protected, but integrated protection does not remove the need for correct cable entry, surge coordination, grounding, and isolation-layout practices.
Provide local decoupling at the device supply pins using the capacitance and placement specified by the Texas Instruments ISO1412 datasheet. Check the logic-side voltage against the 1.71 V to 5.5 V supply range, and verify whether the bus-side interface requires an external reference or bias arrangement. Do not infer capacitor values from generic RS-485 guidance because the verified excerpts do not specify the recommended network.
규정 준수 정보
The verified excerpts do not provide explicit compliance statements for the exact ISO1412DWR orderable part. A comparison-page snippet mentions RoHS and REACH for ISO1410DWR versus ISO1412DWR, but no exact values were supplied, so no compliance conclusion has been inferred.
