LM2903BIDR - Dual 36V Open-Collector Comparator | Texas Instruments
부품 번호: LM2903BIDR ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
LM2903BIDR 개요
A comparator is an analog integrated circuit that determines whether one input voltage is above or below another and switches its output when the differential input crosses a threshold. In the broader semiconductor hierarchy, a comparator belongs to the amplifier and comparator IC family rather than an operational amplifier. Open-collector outputs are useful when multiple devices must share a wired bus or when an external pull-up resistor selects the logic voltage independently of the comparator supply.
The LM2903BIDR supports single- or dual-supply operation, allowing its input and output signals to be referenced around ground in control, sensing, and protection circuits. Its industrial temperature range makes it suitable for equipment operating beyond consumer-temperature limits. The two channels are independent, so one device can perform two threshold functions while sharing a package, although output pull-up components and supply decoupling remain external.
Verified distributor and manufacturer results identify the device as a standard, general-purpose, rail-to-rail-input comparator with open-collector outputs and an 8-SOIC footprint. Texas Instruments describes the B-version as a next-generation member of the LM393 and LM2903 families, emphasizing lower offset, lower bias current, lower supply current, faster response, wider supply capability, and improved ESD robustness.
Typical applications include DC overvoltage monitoring, industrial sensor thresholds, battery-powered indication, window comparators, and relay or alarm activation. Because an open-collector output does not actively drive a high voltage, every application must provide a suitable pull-up resistor and account for its sink-current limit. The collector voltage and supply limits should be checked against the manufacturer datasheet before designing to absolute maximum conditions.
For PCB design, place input resistors close to the relevant pins, decouple the supply close to the device, and route high-impedance input traces away from switching nodes. Where open-collector outputs drive cables or long PCB traces, use a strong pull-up and consider a buffer if additional noise immunity or edge control is required. This page combines verified manufacturer and distributor details with engineering guidance for selecting, sourcing, and replacing the component.
드롭인 대체품: LM2903BIDR — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
LM2903BIDR
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →BA2903F-E2
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LM2903DT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LM2903A
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LM2903BIDR 최대 정격 & 전기적 특성
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| 출력 유형 | Open-collector |
| Maximum Supply Voltage | 36 V |
| Minimum Supply Voltage | 2 V |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| 공급 전류 | 200 µA per comparator |
| Propagation Delay | 1 µs |
| ESD Rating | 2 kV HBM |
| 동작 온도 범위 | -40 °C to +125 °C |
| Industrial Grade | Yes |
| Input Common-Mode Range | Includes ground; rail-to-rail input per distributor listing |
| 패키지 | 8-pin SOIC (D) |
| 실장 유형 | Surface mount |
| Supplier Packaging | Tape and reel |
LM2903BIDR 8-pin soic (d) 핀 구성 가이드
LM2903BIDR(8-pin soic (d) 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: LM2903BIDR.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
LM2903BIDR 적합 용도: 6 애플리케이션s: Industrial Overvoltage Monitor, Battery-Powered Sensor Interface, Motor and Solenoid Drive Protection, Battery Charger Status Detection, Window Comparator and Alarm, Process Control Relay Interface.
Industrial Overvoltage Monitor
The LM2903BIDR fits industrial threshold supervision because it provides two independent differential channels, a 36 V maximum supply rating, and an operating range of -40 °C to +125 °C. Place one channel across a precision divider to detect an overvoltage condition, then use its open-collector output to pull an alarm or interlock line low. The 1 µs response can react quickly to transients, while the 0.37 mV specified input offset helps limit comparator error near the threshold. Because the output is open collector, select the pull-up voltage independently and verify its sink-current capability against the alarm and pull-up current.
추천
Battery-Powered Sensor Interface
LM2903BIDR is suitable for battery-powered sensing because its 2 V minimum supply and 200 µA per-comparator supply current support low-voltage operation. The 3.5 nA input bias specification reduces disturbance to high-impedance sensor nodes, while the open-collector output can alert a low-power controller without actively driving a supply rail. Connect the sensor or divider to one input, a stable threshold reference to the other, and a local pull-up to the controller logic. Include the pull-up’s continuous current, reference current, input leakage, and any indicator load in the complete power budget.
추천
Motor and Solenoid Drive Protection
The LM2903BIDR can supervise a motor, solenoid, or actuator by comparing a scaled feedback voltage with a limit and driving an open-collector shutdown request. Its -40 °C to +125 °C industrial range is useful in equipment exposed to temperature variation, and the 1 µs response supports prompt detection of excursions. The transistor sink must not exceed the comparator’s output limits when pulling down the controller or gate-driver input. Add hysteresis around the threshold to prevent chatter, protect inputs from switching-node transients, and keep the feedback divider physically separated from motor power paths.
추천
Battery Charger Status Detection
The LM2903BIDR can generate charge-complete, undervoltage, or overvoltage status by comparing battery-derived feedback with a reference. Two channels support independent checks, while the open-collector outputs can provide active-low flags to a charger controller or host interface. The 200 µA per-comparator supply current is useful in portable systems, but the complete circuit must account for divider current and logic pull-ups. Choose resistor values for low reference-node impedance, add hysteresis if the battery chemistry creates a slowly changing terminal voltage, and confirm that the pulled-up logic level remains compatible with every connected device.
추천
Window Comparator and Alarm
LM2903BIDR supports a two-channel window arrangement in which each comparator detects one limit of an acceptable input range. Their open-collector outputs can share a wired-AND alarm bus because each node only pulls low, provided every pull-up and device is rated for the common voltage. This arrangement is useful in instrumentation, rack equipment, and industrial controls where a single fault signal must indicate either undervoltage or overvoltage. Verify propagation-delay differences, input offset, output sink current, and logic thresholds if the system requires a precise fault indication; otherwise, account for the 1 µs response when setting debounce timing.
추천
Process Control Relay Interface
The LM2903BIDR can turn a process measurement into an active-low relay-control request when its differential input crosses a preset threshold. The open-collector output is valuable because the pull-up voltage can match an isolated interface or logic domain independently of the analog supply. Industrial temperature operation supports use in factory equipment, while the dual-channel package can monitor two related limits. Keep the pull-up close to the device, choose interface logic that tolerates the collector voltage, and ensure the output sink current includes the relay-driver input and pull-up current. Relay contact transients must be suppressed separately from the comparator’s ESD rating.
추천
엔지니어링 참조 데이터: LM2903BIDR — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM2903BIPWR | LM2903BIDR | BA2903F-E2 | LM2903DT | LM2903A |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | ROHM Semiconductor | STMicroelectronics | 3PEAK |
| Comparator Configuration | Dual differential comparator | Dual comparator | Dual differential comparator | Dual comparator | Dual comparator | Dual comparator |
주요 차별점
- B-version precision and response (vs LM2903DT)
- Higher verified maximum supply rating (vs LM2903DT)
- Documented pin-for-pin replacement path (vs BA2903F-E2)
설계 노트
Do not treat a matching 8-SOIC outline as sufficient proof of interchangeability. Verify the manufacturer pin diagram, exposed functionality, output polarity, supply limits, common-mode range, and sink-current rating before substitution. The supplied evidence specifically reports BA2903F-E2 as pin-for-pin with LM2903BIDR, but LM2903BIPWR uses a different PW footprint and therefore cannot replace the target without PCB redesign.
Place each external pull-up resistor directly beside its open-collector output and the receiving input. Keep the two differential-input nets short, matched where practical, and separated from switching nodes and relay-coil wiring. Route the shared supply and ground connections to maintain low impedance, place the required bypass capacitor at the device, and connect it through a short ground path. These layout controls reduce false threshold transitions and keep a logic-low command from picking up pulses.
Calculate the pull-up current as approximately Vpull-up divided by Rpull-up, then ensure that current remains within the selected output sink rating with margin for supply and temperature variation. Also include continuous comparator supply current, divider current, reference current, and downstream input leakage. Open-collector wiring permits shared nodes, but every connected input must tolerate the pull-up voltage and every device must safely sink the total bus-low current.
규정 준수 정보
The verified excerpts do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. No compliance claim is inferred.
