LMG5126QRXRQ1 - 42V 2.5MHz GaN Boost Converter | TI
부품 번호: LMG5126QRXRQ1 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
LMG5126QRXRQ1 개요
A boost converter is a type of switching DC-DC voltage regulator, belonging to the broader power management IC hierarchy. A boost (step-up) regulator converts a lower input voltage into a higher regulated output voltage by storing energy in an inductor during the switch on-time and transferring it to the output during the off-time. Synchronous boost converters replace the output rectifier diode with a controlled switch to improve efficiency, while GaN (gallium nitride) power technology enables the very high 2.5MHz switching frequency that shrinks inductor and capacitor sizes.
Key features include the wide 6.5V to 42V input range supporting automotive cold-crank and load-dump environments, 2.5MHz operation allowing very small magnetics, and output voltage tracking for controlled power-up and power-down sequencing. TI's integrated GaN power stage approach eliminates external gate-driver complexity compared to discrete GaN solutions, improving EMI and layout robustness in automotive power supplies.
Technically, the LMG5126 family pairs a wide-input boost controller with internal power switches, achieving high power density for pre-boost and regulated high-voltage rail applications. The high switching frequency reduces the energy storage requirement per cycle, enabling compact inductors, and the synchronous topology improves light-load and full-load efficiency versus diode-rectified designs.
Typical applications include automotive pre-boost regulators for audio amplifiers, headlight and display LED rail supplies, 48V-derived auxiliary rails, and communication equipment requiring a regulated rail from an automotive 12V or 24V battery bus.
When designing with the LMG5126QRXRQ1, keep the switching loop and compensation network per the TI datasheet layout guidelines to control EMI at 2.5MHz, and verify the input range margin against transient requirements such as cold crank.
드롭인 대체품: LMG5126QRXRQ1 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LMG5126QRXRQ1 (동일 폼 팩터 및 풋프린트) — 차이점: Qualification, Switching Frequency.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
LMG5126QRXR
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LMG5126QRXRQ1 최대 정격 & 전기적 특성
| 토폴로지 | Synchronous Boost (Step-Up) |
| 입력 전압 범위 | 6.5 V to 42 V |
| Minimum Input (VBIAS >= 6.5V or VOUT >= 6V) | 2.5 V |
| 스위칭 주파수 | 2.5 MHz |
| 출력 유형 | Adjustable with output voltage tracking |
| Power Technology | Integrated GaN power stage |
| Qualification | AEC-Q100 (Q1 automotive) |
| 출력 수 | 1 |
| 동기 정류 | Yes |
| 실장 유형 | Surface Mount |
| Peak Output Current (family, LMG5126VBTR) | 35 A |
| Output Voltage Tracking | Yes |
LMG5126QRXRQ1 standard 핀 구성 가이드
LMG5126QRXRQ1(standard 패키지)의 핀 구성입니다. 이 전력 소자는 게이트, 드레인, 소스 단자를 갖추고 있습니다. 비편향 패키지의 경우 정확한 핀 1 방향과 풋프린트 세부 정보는 제조사 데이터시트를 참조하십시오. 일반적인 응용 분야로는 전원 공급 장치 설계, 모터 구동, 부하 스위칭이 있습니다.
다음에 대한 상세 핀아웃 데이터 없음: LMG5126QRXRQ1.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
LMG5126QRXRQ1 적합 용도: 6 애플리케이션s: Automotive Pre-Boost for Audio Amplifiers, Automotive LED Headlight and Display Supply, 48V-Derived Auxiliary Rails, Automotive Infotainment and Display Power, ADAS Domain Controller Pre-Regulation, Industrial 24V Bus Boost Regulation.
Automotive Pre-Boost for Audio Amplifiers
The LMG5126QRXRQ1's 6.5V to 42V input range and Q1 automotive qualification make it ideal for pre-boosting a 12V automotive battery bus to a stable higher rail feeding class-D audio amplifiers. Output voltage tracking provides clean, sequenced power-up that avoids amplifier pop and clamp conditions during key-off and key-on transients. At 2.5MHz switching, the inductor and output capacitance shrink dramatically compared to 400kHz solutions, saving board area in tight head-unit or amplifier module layouts. Place the GaN converter between the battery rail and amplifier HVDD, and note that synchronous operation maintains efficiency even at light idle volumes.
추천
Automotive LED Headlight and Display Supply
Headlight modules and automotive display backlights need a stable boosted rail from a battery bus that can sag below 8V during cold crank and spike above 40V during load dump. The LMG5126QRXRQ1 covers this window with its 6.5V to 42V input range while the AEC-Q100 Q1 qualification satisfies automotive reliability flows. The 2.5MHz GaN switching frequency keeps the inductor small enough to fit within lamp housings, and output voltage tracking lets the LED rail ramp in sync with a controller enable signal, avoiding brightness overshoot at startup. Efficiency from synchronous rectification reduces thermal load in sealed enclosures.
추천
48V-Derived Auxiliary Rails
In 48V mild-hybrid and zonal architecture vehicles, auxiliary electronics often need a locally boosted or regulated rail derived from intermediate buses. The LMG5126QRXRQ1's wide input range, GaN power stage, and 2.5MHz operation let designers build compact auxiliary converters with high power density. Output voltage tracking enables sequencing with upstream DC-DC stages, and synchronous topology limits switching losses at the high frequency. The integrated GaN approach also removes gate-drive layout sensitivity that plagues discrete GaN designs, improving EMI margins in EMC-tested vehicle modules. Verify thermal performance per the TI datasheet layout guidance.
추천
Automotive Infotainment and Display Power
Infotainment head units combine processors, displays, and audio on multiple rails, requiring a pre-boost stage that is quiet, compact, and sequenced. The LMG5126QRXRQ1 supplies a regulated intermediate rail from the battery, with 2.5MHz GaN switching pushing EMI harmonics above sensitive AM/FM bands where filtering is easier, a key advantage for radio performance. Output voltage tracking coordinates power-up with SoC and display enable signals. The Q1 automotive grade and wide 6.5V to 42V input handle cold crank and jump-start profiles defined in automotive lab environments, while synchronous rectification limits self-heating in enclosed dash electronics.
추천
ADAS Domain Controller Pre-Regulation
ADAS domain controllers draw multi-amp loads at low voltages from a 12V bus that can sag during high-current transients. A front-end boost based on the LMG5126QRXRQ1 holds the intermediate rail steady so downstream point-of-load converters such as LP87524-Q1 and TPS659039-Q1 remain in regulation. The 2.5MHz switching frequency allows a fast control loop, improving transient response to radar-processor load steps, and the Q1 qualification meets automotive deployment requirements. GaN integration reduces layout inductance sensitivity compared to discrete solutions, keeping radiated emissions within CISPR-style test budgets in sensor modules.
추천
Industrial 24V Bus Boost Regulation
Industrial control panels and communications equipment running from 24V bus supplies benefit from the LMG5126's wide input range and high-frequency operation when a higher rail is needed for actuators, displays, or RF front ends. Although this variant carries Q1 automotive qualification, that same AEC-Q100 level of robustness translates into margin for industrial environments with surges and wide temperature excursions. The 2.5MHz GaN switching keeps magnetic components small for DIN-rail and fanless enclosures, and output tracking simplifies power sequencing with programmable-logic and processor rails that must not come up unregulated.
추천
추천 제품 요약
엔지니어링 참조 데이터: LMG5126QRXRQ1 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LMG5126QRXR | LMG5126VBTR | LM5126AQRHBRQ1 |
|---|---|---|---|---|
| Package | QXR (VQFN family) | QXR (VQFN family) - same | 22-PowerVFQFN - different | 32-VQFN (5x5) - different |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Topology | Synchronous GaN boost converter | Synchronous GaN boost converter | Synchronous GaN boost converter | Boost controller (external FETs) |
| AEC-Q100 Qualified | Yes (Q1) | No (standard grade) | No (standard grade) | Yes (Q1) |
주요 차별점
- Integrated GaN power stage eliminates external gate-driver design (vs LM5126AQRHBRQ1)
- Automotive AEC-Q100 Q1 qualification with output voltage tracking (vs LMG5126VBTR)
- Wide 6.5V-42V input with extended low-VIN operation (vs LM5126AQRHBRQ1)
설계 노트
At 2.5MHz switching frequency, parasitic inductance in the SW loop causes voltage ringing and radiated EMI. Keep the GaN converter SW, input capacitor, and ground return loop as tight as possible per the TI LMG5126 datasheet layout section. Because the GaN power stages are integrated, the critical hot loop is fully on-chip, but the input capacitor loop and output sense routing still demand short, wide traces and solid ground planes.
The 2.5MHz switching frequency pushes primary harmonics well above the AM broadcast band (530-1700kHz), which is advantageous for automotive radio performance, but conductive emissions in the 2-30MHz range must still be managed. Use input pi-filtering and verify conducted emissions against your automotive EMC test plan; the TI datasheet application section provides recommended filter components for automotive environments.
The 42V maximum input rating leaves limited headroom above automotive load-dump transients; confirm whether front-end transient suppression (TVS or upstream clamp) is required for your OEM load-dump profile. Also, the 6.5V minimum input applies unless VBIAS >= 6.5V or VOUT >= 6V, which permits 2.5V operation - miswiring the bias path is a common startup failure. Verify the tracking reference ramp against downstream load sequencing requirements.
규정 준수 정보
AEC-Q100 Q1 qualification indicated by the Q1 suffix per TI product page. RoHS/REACH status not stated in retrieved data - confirm on TI.com quality pages.
