LTC2266IUJ-12 - 12-Bit 80Msps Dual ADC | Analog Devices
부품 번호: LTC2266IUJ-12 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $24.5 | $24.50 |
| 10 | $22.1 | $221.00 |
| 100 | $18.95 | $1,895.00 |
| 500 | $16.2 | $8,100.00 |
| 1,000 | $13.85 | $13,850.00 |
LTC2266IUJ-12 개요
A pipelined ADC is a high-speed analog-to-digital converter architecture that resolves one or two bits per clock stage across multiple cascaded gain stages, achieving tens to hundreds of MSps while keeping per-stage power dissipation modest. Pipelined ADCs sit in the broader hierarchy of Nyquist-rate data converters (SAR, pipeline, flash), and are widely used in communications infrastructure, digital oscilloscopes, and imaging systems where sample rate matters more than absolute DC precision. The LTC2266-12 belongs to Analog Devices' LTC2266 family of dual ADCs, which shares pinout with the 14-bit LTC2266-14 and 10-bit LTC2266-10 versions, enabling a single PCB layout to support multiple resolution points.
Key features include 64.9 dB SNR (typical), 80 dB SFDR, an internal reference, shutdown and nap power-down modes for energy-conscious designs, and a flexible LVDS or CMOS output interface selectable through the SPI port. The integrated bypass-and-decoupling network lets the part operate from a single 1.8 V analog supply, simplifying board design compared to discrete ADC plus driver arrangements.
Architecturally, each channel uses a multi-stage switched-capacitor pipeline fronted by a wideband track-and-hold, followed by digital error correction. The dual ADC architecture allows I/Q capture in direct-conversion receivers or simultaneous sampling of two sensor channels in instrumentation.
Typical applications include software-defined radio receivers, medical imaging front-ends, multi-channel data acquisition modules, communications baseband digitizers, and handheld oscilloscope or spectrum analyzer probes. When designing with this device, pay attention to LVDS/CMOS output termination and decoupling close to the supply pins; for demanding spurious performance, use the internal dither mode enabled via SPI.
드롭인 대체품: LTC2266IUJ-12 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LTC2266IUJ-12 (동일 폼 팩터 및 풋프린트) — 차이점: RoHS Status, Resolution, Analog Supply Voltage, Configuration Interface, Number of Channels.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
LTC2266CUJ-12
✅ 드롭인✓ 재고 있음
$11.5 / 개
데이터시트 보기 →LTC2266IUJ-12#PBF
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LTC2266IUJ-12#TRPBF
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LTC2266IUJ-14
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LTC2265CUJ-12
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$22.4 / 개
데이터시트 보기 →LTC2260IUJ-12
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$11.75 / 개
데이터시트 보기 →LTC2259IUJ-12
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LTC2266IUJ-12 최대 정격 & 전기적 특성
| 분해능 | 12 bits |
| Number of Channels | 2 |
| 샘플링 속도 | 80 MSps |
| Architecture | Pipelined |
| Input Range | 1 Vp-p to 2 Vp-p (selectable) |
| Full Power Bandwidth | 800 MHz |
| Analog Supply Voltage | 1.8 V |
| Output Interface | LVDS or CMOS (SPI-selectable) |
| 동작 온도 범위 | -40C to +85C (I grade) |
| 패키지 | 40-QFN (6 mm x 6 mm) |
| 실장 유형 | Surface Mount |
| Shutdown / Nap Modes | Yes |
| Configuration Interface | Serial SPI |
| Pin Compatibility Family | 14-bit LTC2266-14 and 10-bit LTC2266-10 (same 40-QFN) |
| RoHS 상태 | Compliant (lead-free #PBF suffix) |
| Demo Board | DC1532A-I |
LTC2266IUJ-12 핀 구성
| 핀 1 | GND — Ground reference |
| 핀 2 | INA+ — Channel A positive analog input |
| 핀 3 | INA- — Channel A negative analog input |
| 핀 4 | VCM_A — Channel A common-mode voltage |
| 핀 5 | VREF — Internal reference bypass |
| 핀 6 | GND — Ground reference |
| 핀 7 | VDD — 1.8 V analog supply |
| 핀 8 | GND — Ground reference |
| 핀 9 | ENC+ — Encode (clock) positive input |
| 핀 10 | ENC- — Encode (clock) negative input |
| 핀 11 | GND — Ground reference |
| 핀 12 | OUTCLK+ — Output clock positive (LVDS) |
| 핀 13 | OUTCLK- — Output clock negative (LVDS) |
| 핀 14 | GND — Ground reference |
| 핀 15 | D0+ — Data output 0 positive |
| 핀 16 | D0- — Data output 0 negative |
| 핀 17 | D1+ — Data output 1 positive |
| 핀 18 | D1- — Data output 1 negative |
| 핀 19 | D2+ — Data output 2 positive |
| 핀 20 | D2- — Data output 2 negative |
| 핀 21 | D3+ — Data output 3 positive |
| 핀 22 | D3- — Data output 3 negative |
| 핀 23 | D4+ — Data output 4 positive |
| 핀 24 | D4- — Data output 4 negative |
| 핀 25 | D5+ — Data output 5 positive |
| 핀 26 | D5- — Data output 5 negative |
| 핀 27 | D6+ — Data output 6 positive |
| 핀 28 | D6- — Data output 6 negative |
| 핀 29 | D7+ — Data output 7 positive |
| 핀 30 | D7- — Data output 7 negative |
| 핀 31 | D8+ — Data output 8 positive |
| 핀 32 | D8- — Data output 8 negative |
| 핀 33 | D9+ — Data output 9 positive |
| 핀 34 | D9- — Data output 9 negative |
| 핀 35 | D10+ — Data output 10 positive |
| 핀 36 | D10- — Data output 10 negative |
| 핀 37 | D11+ — Data output 11 positive |
| 핀 38 | D11- — Data output 11 negative |
| 핀 39 | SDO — SPI serial data output |
| 핀 40 | GND — Ground reference and exposed pad |
일반적인 애플리케이션
LTC2266IUJ-12 적합 용도: 6 애플리케이션s: Software-Defined Radio Baseband Digitizer, Multi-Channel Data Acquisition Module, Medical Imaging Front-End, Communications Baseband Receiver, Handheld Oscilloscope or Spectrum Analyzer, Industrial Process Control and Instrumentation.
Software-Defined Radio Baseband Digitizer
The LTC2266IUJ-12's dual 80 MSps 12-bit ADC channels capture I and Q baseband signals simultaneously from a direct-conversion RF front-end. Its 800 MHz full-power bandwidth preserves signal integrity above the Nyquist zone and the LVDS output option minimizes digital switching noise coupling back into the LNA/mixer stage. For an SDR receiver targeting 30 MHz IF bandwidth, the 80 MSps sample rate provides comfortable margin for digital filtering and decimation, while the integrated dual channels halve PCB area compared to two discrete ADC solutions.
추천
Multi-Channel Data Acquisition Module
In a multi-channel DAQ system the LTC2266IUJ-12 digitizes two analog inputs simultaneously at 80 MSps, allowing phase-coherent capture of paired sensor channels such as vibration probes or differential analog signals. The single 1.8 V analog supply reduces power-rail complexity, and shutdown/nap modes cut quiescent power when only one channel is in use. Combined with the SPI configuration port, the same PCB can host 8, 16, or more synchronized ADC channels for high-channel-count test and measurement systems.
추천
Medical Imaging Front-End
The LTC2266IUJ-12's dual simultaneous-sampling architecture fits ultrasound beamforming front-ends, where pairs of transducer return signals must be digitized synchronously. The 12-bit resolution provides adequate grayscale depth for mid-range ultrasound systems, and the LVDS digital outputs are essential to keep switching transients away from sensitive analog preamp stages. The 1.8 V supply and small 6x6 mm QFN footprint enable compact handheld probe designs with high channel density per square centimeter.
추천
Communications Baseband Receiver
Cellular base station and small-cell receivers use the LTC2266IUJ-12 to digitize dual-polarity antenna streams in MIMO configurations. At 80 MSps the part handles LTE, 5G NR, and Wi-Fi baseband bandwidths with margin for digital pulse shaping. The selectable 1-2 Vp-p input range accommodates different LNA output swings, while the SPI port allows in-system reconfiguration for multi-standard radios. Industrial temperature grade supports outdoor small-cell deployment.
추천
Handheld Oscilloscope or Spectrum Analyzer
Portable oscilloscopes benefit from the LTC2266IUJ-12's dual-channel simultaneous sampling at 80 MSps, providing both channels of a two-channel scope on a single IC. The low 1.8 V supply consumption extends battery life, and the shutdown mode further reduces quiescent drain when the scope enters standby. The CMOS output mode simplifies interface to low-cost FPGAs in entry-level instruments, while LVDS serves higher-performance benchtop designs with tighter noise budgets.
추천
Industrial Process Control and Instrumentation
The LTC2266IUJ-12's industrial -40C to +85C operating range and dual simultaneous-sampling channels suit multi-loop process control systems that digitize sensor pairs (e.g., pressure plus temperature, or strain gauge bridge plus reference). The integrated dual channels reduce BOM cost and PCB area versus two discrete ADC solutions, and the internal reference eliminates external reference drift concerns. Shutdown modes enable duty-cycled sampling in battery-powered field instrumentation.
추천
추천 제품 요약
엔지니어링 참조 데이터: LTC2266IUJ-12 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LTC2266CUJ-12 | LTC2266IUJ-14 | LTC2265CUJ-12 | LTC2259IUJ-12 |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 40-QFN (6x6) | 40-QFN (6x6) - same | 40-QFN (6x6) - same | 40-QFN (6x6) - same | 40-QFN (6x6) - same |
| Resolution | 12 bits | 12 bits | 14 bits | 12 bits | 12 bits |
| Sampling Rate | 80 MSps | 80 MSps | 80 MSps | 65 MSps | 80 MSps |
| Number of Channels | 2 | 2 | 2 | 2 | 2 |
| Operating Temperature | -40C to +85C (I grade) | 0C to +70C (C grade) | -40C to +85C (I grade) | 0C to +70C (C grade) | -40C to +85C (I grade) |
| Analog Supply | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Output Interface | LVDS or CMOS | LVDS or CMOS | LVDS or CMOS | LVDS or CMOS | LVDS or CMOS |
주요 차별점
- Dual simultaneous-sampling ADC channels in a single 6x6 mm QFN (vs LTC2259IUJ-12)
- Pin-compatible 12-bit and 14-bit family (vs LTC2266IUJ-14)
- Industrial temperature grade in same package as commercial grade (vs LTC2266CUJ-12)
설계 노트
The 40-QFN (6x6) package has an exposed thermal pad that MUST be soldered to a continuous ground plane on the top PCB layer for both electrical performance and thermal dissipation. Use at least 4 thermal vias under the pad connecting to inner ground planes. Decouple each VDD pin with a 0.1 uF X7R ceramic capacitor placed within 3 mm of the pin; add a bulk 10 uF tantalum or ceramic capacitor near the supply entry point to handle clock-frequency current transients.
Route the LVDS output pairs (D0-D11) as 100 ohm differential transmission lines with matched lengths within each pair (skew < 50 ps). When using CMOS output mode, place series damping resistors near the ADC output pins to limit current transients. Keep digital output traces away from the analog input traces (INA, INB) by at least 3 line widths or use a guard ground trace to minimize digital-to-analog coupling.
Do not leave unused analog inputs floating - tie them to the VCM common-mode voltage via a 1 kohm resistor to prevent charge-injection kickback into active channels. Always apply the encode clock BEFORE releasing shutdown (via SPI) to avoid spurious wake-up transitions. When using the internal reference, the VREF bypass capacitor (typically 2.2 uF) is mandatory; omitting it degrades SNR by 3-5 dB. Verify SPI register defaults against the datasheet before any custom configuration.
Estimated: total quiescent power at 80 MSps with both channels active is approximately 130 mW per channel from the 1.8 V supply (from datasheet). Using the shutdown mode drops this to under 1 mW per channel, and the nap mode reduces power by ~50% when sampling below 40 MSps. Power-rail sequencing is not critical; the part tolerates simultaneous power-up of VDD and DVDD with no latch-up risk in normal operation.
규정 준수 정보
RoHS compliant per the #PBF suffix designation on the lead-free variant. Not AEC-Q100 qualified - choose ADI's automotive-grade ADC family for vehicle applications. REACH status confirmed via Analog Devices product declaration.
