MAX1419ETN+D - 15-Bit 65Msps ADC | 56-QFN | Maxim Integrated
부품 번호: MAX1419ETN+D ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $38.5 | $38.50 |
| 10 | $35.2 | $352.00 |
| 100 | $31.75 | $3,175.00 |
| 500 | $28.1 | $14,050.00 |
| 1,000 | $25.4 | $25,400.00 |
MAX1419ETN+D 개요
An ADC (Analog-to-Digital Converter) is a data-conversion integrated circuit that samples continuous-time analog signals and produces discrete-time, finite-resolution digital codes. Within the data-converter hierarchy, the MAX1419ETN+D belongs to the high-speed pipeline ADC class, which sits between general-purpose SAR (Successive Approximation Register) ADCs and very-high-speed flash converters. Pipeline ADCs combine a small number of low-resolution stages with digital error correction to achieve 10-16 effective bits at sample rates from 20 to 200 Msps, making them the dominant architecture for wireless baseband, ultrasound, and broadband instrumentation.
Key specifications include 65 Msps maximum conversion rate, 15-bit resolution, a 200 MHz -1 dB full-power input bandwidth on the track-and-hold, an internal 2.56 Vp-p differential input range, and a typical SNR near 75 dBFS at low input frequencies. The part supports CMOS-compatible digital outputs and offers a per-pin or byte-wide output mode for flexible FPGA or ASIC interfacing.
Architecturally, the MAX1419ETN+D uses a multi-stage pipelined converter core with on-chip bandgap reference and integrated input track-and-hold. The 200 MHz input bandwidth allows the device to be clocked at up to 65 Msps while preserving -79.3 dBFS noise floor performance for baseband signals below approximately 30 MHz, while optional external filtering can extend usable bandwidth into the IF range.
Typical applications include wireless baseband digitization for WCDMA/UMTS receivers, IF sampling in narrow-band radio links, medical ultrasound signal chains, and high-speed instrumentation. The wide input bandwidth also makes the part useful as a general-purpose 65 Msps digitizer in multichannel data-acquisition boards.
Designers should pay close attention to analog/digital supply decoupling, ground-plane partitioning, and the proper sequencing of the +5 V AVDD and +3 V DVDD rails. The exposed paddle must be soldered to a continuous low-impedance ground plane to achieve the rated thermal and dynamic performance, and the differential input must be DC-biased within the part's common-mode range for full-scale codes.
This page synthesizes distributor pricing, same-family pin-compatible alternatives (MAX1418, MAX1427, MAX1429, MAX1430), and practical layout notes that go beyond the manufacturer datasheet.
드롭인 대체품: MAX1419ETN+D — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MAX1419ETN+D (동일 폼 팩터 및 풋프린트) — 차이점: Noise Floor, Terminal Form, Package, Number of Channels, Analog Supply Voltage.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MAX1418ETN+D
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MAX1427ETN+D
✅ 드롭인✓ 재고 있음
$25.95 / 개
데이터시트 보기 →MAX1428ETN+D
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MAX1429ETN+D
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MAX1430ETN+D
✅ 드롭인✓ 재고 있음
$23.8 / 개
데이터시트 보기 →MAX1419ETN+D 최대 정격 & 전기적 특성
| 분해능 | 15 bit |
| Sample Rate (max) | 65 Msps |
| Noise Floor | -79.3 dBFS (baseband, per datasheet title) |
| Number of Channels | 1 |
| Input Configuration | Fully differential |
| Full-Scale Input Range | 2.56 Vp-p (differential) |
| -1 dB Full-Power Input Bandwidth | 200 MHz |
| Analog Supply Voltage (AVDD) | 5 V |
| Digital Supply Voltage (DVDD) | 3 V |
| 동작 온도 범위 | -40 C to +85 C (industrial) |
| 패키지 | 56-pin QFN-EP (HVQCCN, 8x8 mm) |
| 실장 유형 | Surface Mount |
| Terminal Form | No-lead |
| RoHS 상태 | Compliant |
| Lead-Free / Halogen-Free | Lead-free per Maxim datasheet |
MAX1419ETN+D 56-pin qfn-ep (hvqccn, 8x8 mm) 핀 구성 가이드
MAX1419ETN+D(56-pin qfn-ep (hvqccn, 8x8 mm) 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MAX1419ETN+D.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MAX1419ETN+D 적합 용도: 6 애플리케이션s: Wireless Baseband Digitization, Medical Ultrasound Signal Chain, IF Sampling in Narrowband Radio, Broadband Data Acquisition, Cable Modem / Set-Top Box Downstream Digitization, Radar and Lidar Baseband Digitization.
Wireless Baseband Digitization
The MAX1419ETN+D's 65 Msps sample rate and 15-bit resolution make it a strong fit for WCDMA/UMTS baseband I/Q digitization where a -79.3 dBFS noise floor preserves dynamic range for receive sensitivity. Placed between the analog front-end quadrature demodulator and the digital baseband DSP/ASIC, the ADC accepts a fully differential 2.56 Vp-p signal from a passive antialiasing RC network. Designers should provide a common-mode bias within the part's input range and use a low-jitter clock to keep aperture-induced SNR degradation below 0.5 dB at 65 Msps.
추천
Medical Ultrasound Signal Chain
In ultrasound receivers the MAX1419ETN+D digitizes the post-TGC (time-gain-compensated) signal at up to 65 Msps with 15-bit resolution. The 200 MHz -1 dB full-power input bandwidth comfortably exceeds the harmonic content of 5-15 MHz ultrasound transducers, while the -79.3 dBFS noise floor preserves dynamic range for harmonic and contrast imaging. Multi-channel ultrasound boards typically place one MAX1419ETN+D per channel in parallel, sharing a common low-jitter clock and a continuous ground plane under the exposed paddle to achieve rated crosstalk and SNR performance.
추천
IF Sampling in Narrowband Radio
With a 200 MHz input bandwidth the MAX1419ETN+D can undersample intermediate frequencies in narrowband receivers, eliminating one or more analog IF downconversion stages. Per the Maxim datasheet selection table, the MAX1418 (IF-grade) sibling is preferred when the IF is high; the MAX1419ETN+D itself targets baseband, but its wide T/H bandwidth allows it to handle low IFs below ~30 MHz while maintaining -79.3 dBFS noise floor. Designers should pair the ADC with a sharp antialiasing bandpass filter and a low-jitter clock source to keep SNR above the rated value.
추천
Broadband Data Acquisition
General-purpose data-acquisition boards use the MAX1419ETN+D to digitize 15-bit wideband signals from test sensors, RF downconverters, and broadband instrumentation. At 65 Msps the part captures a Nyquist bandwidth of approximately 32.5 MHz, suitable for spectrum-analyzer-class instruments and vibration/acoustic monitoring. The +5 V AVDD / +3 V DVDD split supply simplifies mixed-signal board design, while the QFN-EP exposed paddle enables a low-impedance ground plane under the analog front end for clean analog returns.
추천
Cable Modem / Set-Top Box Downstream Digitization
In cable-modem downstream and digital set-top box receivers, the MAX1419ETN+D digitizes the QAM demodulated I/Q baseband at up to 65 Msps with 15-bit resolution. The -79.3 dBFS noise floor provides the dynamic-range margin needed for 256-QAM and 1024-QAM symbol recovery, while the 2.56 Vp-p differential input range matches typical tuner output levels after passive attenuation. The 56-QFN-EP footprint keeps the analog chain compact on space-constrained consumer hardware.
추천
Radar and Lidar Baseband Digitization
Automotive and industrial radar/lidar front-ends use the MAX1419ETN+D to digitize baseband I/Q signals from FMCW and pulsed receivers. The 65 Msps sample rate supports 20-30 MHz baseband chirp bandwidth while the 200 MHz input T/H bandwidth preserves harmonic and beat-frequency content. Designers should pay close attention to clock jitter - a 1 ps RMS jitter contributes roughly 9 dB of SNR degradation at 65 Msps, which can dominate the -79.3 dBFS noise floor of the ADC itself.
추천
추천 제품 요약
엔지니어링 참조 데이터: MAX1419ETN+D — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MAX1418ETN+D | MAX1427ETN+D | MAX1428ETN+D | MAX1429ETN+D | MAX1430ETN+D |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 56-QFN-EP (HVQCCN) | 56-QFN-EP (HVQCCN) - same | 56-QFN-EP (HVQCCN) - same | 56-QFN-EP (HVQCCN) - same | 56-QFN-EP (HVQCCN) - same | 56-QFN-EP (HVQCCN) - same |
| Sample Rate (Msps) | 65 | 65 | 80 | 80 | 100 | 100 |
| Resolution (bit) | 15 | 15 | 15 | 15 | 15 | 15 |
| Target Application | Baseband | IF | Baseband | IF | Baseband | IF |
| Analog Supply (V) | 5 | 5 | 5 | 5 | 5 | 5 |
| Digital Supply (V) | 3 | 3 | 3 | 3 | 3 | 3 |
| Input Configuration | Fully differential | Fully differential | Fully differential | Fully differential | Fully differential | Fully differential |
주요 차별점
- Pin-compatible speed and application-grade options within the same footprint (vs MAX1418ETN+D)
- Lower power and cost at matched baseband performance (vs MAX1427ETN+D)
- True Maxim cross-family upgrade path (vs MAX1430ETN+D)
설계 노트
Estimated: at 65 Msps with a 30 MHz input the MAX1419ETN+D is sensitive to clock jitter. Use a dedicated low-jitter clock driver (jitter below 1 ps RMS) and route the clock trace as a 50 ohm microstrip with continuous ground reference. Place a 10 nF X7R bypass capacitor within 2 mm of each AVDD pin and a 1 uF tantalum or polymer cap at the regulator output. Connect the exposed paddle to a continuous low-impedance analog ground plane cut from the digital return plane; do not route digital signals directly under the exposed paddle.
The MAX1419ETN+D uses a split +5 V AVDD / +3 V DVDD supply. Sequence AVDD before DVDD at power-up (or use the part's on-chip POR tolerance) to prevent digital output drivers from sinking current into an unpowered analog core. Decouple each AVDD pin with 10 nF + 100 nF + 10 uF in parallel, and isolate the analog 5 V regulator from the digital 3 V regulator with separate ferrite beads to prevent switching-noise coupling into the reference.
Drive the fully differential analog input with a transformer-coupled or op-amp-driven differential source biased to the part's specified common-mode voltage. Estimated: source impedance above 100 ohm at the input will degrade the -79.3 dBFS noise floor; keep the differential source impedance at or below 50 ohm and place the antialiasing RC network within 5 mm of the input pins. For the digital CMOS outputs, length-match the bus to within 2 mm across all bits to avoid code-dependent skew on the capture clock.
Do not exceed the 2.56 Vp-p differential input range - overdrive at the input clips codes and can damage the ESD structure of the front-end T/H. Do not float the exposed paddle; unterminated paddles cause both thermal runaway and degraded SNR. Do not drive the digital outputs into a bus that is held at a higher DVDD than the part - level translation is required if interfacing to a 3.3 V-tolerant FPGA when DVDD is 3.0 V.
규정 준수 정보
RoHS-compliant and lead-free per Maxim datasheet packaging information. AEC-Q100 not applicable - this is a commercial/industrial ADC, not an automotive-qualified part.
