MAX14802CCM+T - 16-Ch 48 Ohm HV Switch | Analog Devices
부품 번호: MAX14802CCM+T ✓ 활성MAX14802CCM+T 개요
A high-voltage analog switch is an integrated semiconductor device that routes analog signals through independently controlled channels. Its hierarchy extends from an analog switch to a multiplexer or demultiplexer, then to an interface IC and semiconductor. The MAX14802CCM+T uses HVCMOS technology to combine high-voltage switching capability with low charge injection, making it suitable for precision systems that cannot tolerate signal disturbance during switching.
The primary feature set includes 16 independently switched SPST paths, 48 ohm on-resistance, and low charge injection. The MAX14802 is intended for ultrasonic imaging and printer applications, where serialized control reduces external component count while high-voltage signals must be routed with low injection. A digital interface clocks switch commands into the 16-bit shift register, and the programmable latch retains the switching state when required.
The device combines a digital control section with high-voltage analog switch channels implemented using HVCMOS process technology. The 48-LQFP package provides 48 external terminals for the switch matrix and control interface. The MAX14802CCM+T operates from 2.7 V to 5.5 V, while the documented operating temperature range is 0 C to 70 C. Its switch-on time is documented as 3500 ns, a figure designers should evaluate against the acquisition timing of the driven imaging or printing system.
Typical uses include medical ultrasound receiver and transmitter signal routing, industrial printer printhead control, and other multi-channel analog systems requiring centralized switch control. The 16-channel architecture is useful when many signal paths must be sequenced consistently. In ultrasonic equipment, controlled switching supports the repetitive selection of transducers or receiver channels, while in printer systems it can simplify the control of multiple high-voltage analog outputs.
When assigning PCB connections, use the pin-description table and package drawing in the Analog Devices manufacturer datasheet. Confirm that every switched node remains within the device's absolute maximum ratings and that control signals meet the specified logic levels. Provide a stable low-noise supply and route the digital interface away from sensitive analog nodes to minimize coupling into the switched channels.
This page combines the MAX14802 family architecture, package information, operating limits, and application guidance with practical design notes for high-voltage analog switching. It also identifies related family options and identifies the parameters that must be checked before replacing the device in an existing ultrasonic-imaging or printer design.
드롭인 대체품: MAX14802CCM+T — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MAX14802CCM+T (동일 폼 팩터 및 풋프린트) — 차이점: Number of Channels, Package, State Retention, Switch Configuration.
MAX14803CCM+
✅ 드롭인가격 문의
데이터시트 보기 →MAX14803A
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MAX14802CCM+T 최대 정격 & 전기적 특성
| Number of Channels | 16 channels |
| Switch Type | SPST |
| On-Resistance | 48 ohm |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Switch-On Time | 3500 ns |
| 동작 온도 범위 | 0 C to +70 C |
| Process Technology | HVCMOS |
| Internal Control Register | 16-bit shift register |
| State Retention | Programmable latch |
| Control Interface | Digital serial interface |
| 패키지 | 48-LQFP, 7 x 7 mm |
| 핀 수 | 48 pins |
| 실장 유형 | Surface mount |
| Primary Application | Ultrasonic imaging and printer applications |
| Charge Injection | Low charge injection |
MAX14802CCM+T 48-lqfp, 7 x 7 mm 핀 구성 가이드
MAX14802CCM+T(48-lqfp, 7 x 7 mm 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: MAX14802CCM+T.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MAX14802CCM+T 적합 용도: 6 애플리케이션s: Medical Ultrasound Signal Routing, Industrial Printer Printhead Control, Ultrasonic Transducer Selection, Precision Test and Measurement Systems, Multi-Channel Analog Signal Conditioning, Automated Production Test Fixtures.
Medical Ultrasound Signal Routing
The MAX14802CCM+T fits medical ultrasound systems that require multiple analog channels to be selected under digital control. Its 16 SPST paths, 48 ohm on-resistance, and low-charge-injection switching characteristics help reduce disturbance when the receiver selects transducers or test points. The device operates from 2.7 V to 5.5 V and accepts switch commands through a 16-bit shift register with programmable state retention. Its documented 3500 ns switch-on time must be compared with the ultrasound acquisition window and settling requirements. High-voltage node limits, leakage, and isolation behavior should be verified against the transducer interface before the device is used in a patient-connected system.
추천
Industrial Printer Printhead Control
The MAX14802CCM+T is suitable for industrial printer electronics that route several controlled analog or high-voltage signals to a printhead or driver network. Sixteen SPST channels provide a compact way to organize repeated switching, while the digital serial interface reduces parallel control wiring. Its 48 ohm on-resistance and 48-LQFP 7 x 7 mm package support integration into a multi-channel controller. The 3500 ns switch-on time should be included in edge-timing and signal-settling analysis. Because switched-node voltage, load current, and off-state behavior are application-critical limits, the complete printer driver requirements should be checked against the manufacturer datasheet before layout release.
추천
Ultrasonic Transducer Selection
The MAX14802CCM+T can be used where an ultrasonic system must select among numerous transducer or receive channels. Its 16-channel SPST architecture, 48 ohm on-resistance, and low-charge-injection design support controlled signal routing, while the programmable latch helps retain a selected switching configuration. The serial control interface allows the channel map to be integrated with a scan controller rather than driven through 16 separate command lines. The 2.7 V to 5.5 V operating supply fits common low-voltage control systems. Validate the 3500 ns switch-on time, maximum switched voltage, and channel leakage against the transducer impedance and available headroom to ensure that timing and signal integrity remain acceptable.
추천
Precision Test and Measurement Systems
The MAX14802CCM+T can support compact test systems that route multiple analog measurement nodes under repeatable digital commands. Its 16 SPST channels provide centralized path selection, and the 48 ohm on-resistance defines the basic insertion-loss characteristic that must be included in accuracy budgets. The internal 16-bit shift register and programmable latch simplify deterministic state control. The 0 C to 70 C operating range supports commercial-temperature instrumentation. For precision measurements, engineers should also characterize off leakage, capacitance, charge injection, and switching transients under the actual source impedance and bandwidth. The 3500 ns switch-on time establishes an important timing boundary for calibration and settling requirements.
추천
Multi-Channel Analog Signal Conditioning
The MAX14802CCM+T is appropriate for centralized analog signal-routing blocks that require numerous channels but only a small number of control connections. Sixteen SPST paths, 48 ohm on-resistance, and serial state control allow a controller to configure different routing combinations through a 16-bit shift register. The 2.7 V to 5.5 V logic supply range facilitates integration with conventional control circuitry, while the 48-LQFP 7 x 7 mm package limits board area. Signal-chain designers should place the device away from high-energy switching nodes and evaluate trace coupling, return paths, and connector transitions. Off-state behavior and leakage must be verified when source impedances are high enough for leakage to affect measurement accuracy.
추천
Automated Production Test Fixtures
The MAX14802CCM+T can organize channel selection in automated test fixtures that connect one controller to multiple analog test points. The 16 SPST architecture reduces the number of external routing commands, and the programmable latch supports repeatable states between measurements. Its 48 ohm on-resistance should be considered when the test system uses high-impedance sources, while the 3500 ns switch-on time defines part of the settling interval. The 0 C to 70 C operating range is appropriate for many factory environments, but fixture heating and enclosure temperature must remain within that range. Confirm maximum switched voltage, leakage, and logic thresholds before connecting external equipment directly to the device terminals.
추천
추천 제품 요약
엔지니어링 참조 데이터: MAX14802CCM+T — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MAX14803CCM+ | MAX14803A |
|---|---|---|---|
| Package | 48-LQFP (7x7 mm) | 48-LQFP (7x7 mm) | 48-LQFP (7x7 mm) |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Number of Channels | 16 channels | 16 channels | 16 channels |
| Switch Type | SPST | SPST | SPST |
| On-Resistance | 48 ohm | 48 ohm | 48 ohm |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Process Technology | HVCMOS | HVCMOS | HVCMOS |
| Control Architecture | Digital interface, 16-bit shift register, programmable latch | Digital interface, 16-bit shift register, programmable latch | Digital interface, 16-bit shift register, programmable latch |
주요 차별점
- Sixteen individually addressed SPST channels with serialized control (vs MAX14803CCM+)
- Documented 48 ohm on-resistance with a 3500 ns switch-on time (vs MAX14803A)
- Single-package integration of switching and state retention (vs MAX14803CCM+)
설계 노트
Use the 48-LQFP 7 x 7 mm land pattern and terminal numbering from the Analog Devices manufacturer datasheet. Keep serial clock, latch, and data traces away from high-impedance switched nodes, and provide a low-impedance return path beneath digital routing where practical. Place the decoupling capacitor close to the supply and ground terminals using the layout guidance in the device documentation.
Budget for the documented 3500 ns switch-on time when defining acquisition or settling intervals. Charge injection can create a transient proportional to switched-node capacitance and source impedance, so evaluate the complete source, connector, and receiver network rather than relying only on the 48 ohm on-resistance. For low-frequency precision signals, include leakage and off-state capacitance in the error budget.
Do not treat the 2.7 V to 5.5 V control-supply range as the permitted voltage on every switched terminal. Check the separate absolute-maximum and recommended operating ratings before connecting ultrasonic, printer, or test-fixture nodes. Also verify power-up sequencing, logic thresholds, and latch behavior so no uncontrolled channel state is applied to external circuitry.
Route each switched node directly toward its destination and keep it away from clock and data lines. If high-voltage nodes are present, maintain the creepage and clearance required by the board voltage, contamination level, and applicable product-safety design rules. Ground-plane continuity beneath the device helps control return currents, while test points should avoid loading sensitive switched nodes.
규정 준수 정보
No explicit environmental or automotive qualification statements were identified for this part. Use the current manufacturer product documentation and project-specific procurement requirements for compliance verification.