MAX399EGE - 100Ω Dual 4:1 CMOS Analog Multiplexer | ADI
부품 번호: MAX399EGE ✓ 활성MAX399EGE 개요
A CMOS analog multiplexer is an interface IC that routes one of several analog inputs to a shared output under digital control. Within the signal-chain hierarchy, the MAX399 belongs to the analog switch and multiplexer class, where low insertion resistance, channel matching, signal-range flatness, and switching control determine how accurately a selected signal reaches downstream converters or instrumentation.
The MAX398/MAX399 family provides on-resistance below 100Ω, matching between channels to within 6Ω, and on-resistance variation of no more than 11Ω across the specified analog signal range. These characteristics make the device useful when several sensors, converter outputs, or test points must be connected to a shared analog input. The EGE package is identified as a 16-QFN, 4x4 mm surface-mount option.
The multiplexer's two 4:1 circuits reduce the number of external analog input connections required by a factor of four per circuit. Digital select inputs determine which source reaches each common terminal, allowing a compact ADC front end to scan multiple analog sources without requiring a separate switch for every channel. Exact channel timing, control logic, supply limits, leakage, and operating-temperature details should be confirmed in the MAX398/MAX399 manufacturer data sheet before final circuit design.
Typical uses include multiplexed sensor acquisition, instrumentation inputs, signal-chain routing, automated test equipment, and analog measurement systems. It is particularly relevant where source impedance is low enough that the multiplexer's on-resistance does not dominate the measurement error and where matched resistance between channels simplifies calibration.
For layout, treat every selected analog trace as a potentially high-impedance node. Keep input and output paths short, provide a quiet return path, and observe the manufacturer's guidance for bypassing and control-signal timing. Because pin names, logic levels, supply requirements, and full switching specifications are not reproduced on this page, use the official pin-description table and typical application circuit when laying out the PCB.
This page combines the MAX399EGE package identity, on-resistance and matching characteristics with practical routing guidance and qualified comparisons. It also separates electrically similar devices that use different footprints from genuine pin-compatible replacements, helping engineers avoid assuming that equal switching performance guarantees a drop-in upgrade.
드롭인 대체품: MAX399EGE — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청MAX399EGE 사양
| Multiplexer Configuration | 2 circuits, each configured as 4:1 |
| Total Channels | 8 channels |
| On-Resistance | Less than 100Ω |
| On-Resistance Matching Between Channels | Within 6Ω |
| On-Resistance Variation Over Analog Signal Range | 11Ω maximum |
| Technology | Monolithic CMOS |
| 패키지 | 16-pin QFN, 4x4 mm |
| 실장 유형 | Surface mount |
| Circuit Count | 2 analog switch circuits |
| Switching Ratio | 4:1 per circuit |
| Nominal On-Resistance | 100Ω |
MAX399EGE 16-pin qfn, 4x4 mm 핀 구성 가이드
MAX399EGE(16-pin qfn, 4x4 mm 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: MAX399EGE.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MAX399EGE 적합 용도: 6 애플리케이션s: Multiplexed Sensor Acquisition, Precision Instrumentation Signal Routing, Automatic Test Equipment, Audio and Communication Signal Routing, Data Converter Front End, Industrial Control Analog Fan-Out.
Multiplexed Sensor Acquisition
The MAX399EGE fits sensor-frontend designs that must route several analog inputs to a shared converter. Its two independent 4:1 sections can connect eight sources in total, while on-resistance below 100Ω and channel matching within 6Ω help reduce path-dependent amplitude error. Place the multiplexer close to the sensor interfaces, keep the selected traces short, and include the switch resistance in the source-impedance calculation. Confirm input bias current, leakage, common-mode limits, and allowable signal range in the manufacturer data sheet before selecting sensor excitation and protection networks.
추천
Precision Instrumentation Signal Routing
The MAX399EGE is useful in instrumentation that selects among test points, amplifiers, or external sensor channels. Its resistance variation of 11Ω maximum across the specified analog signal range and matching within 6Ω support repeatable channel calibration. Use short, guarded analog traces and a solid ground reference to reduce coupling from digital control and relay circuitry. The device is best suited to low-impedance sources; confirm the maximum signal current and input common-mode range in the MAX398/MAX399 manufacturer data sheet before adding amplifier gain.
추천
Automatic Test Equipment
The MAX399EGE can scan multiple analog test nodes in compact automated test equipment. Two 4:1 switches provide eight source selections while reducing the number of front-end connections required from the measurement circuit. On-resistance below 100Ω must be included in source impedance and gain-error analysis, especially when driving high-resolution converters. Place the mux near the measurement adapter, separate select routing from sensitive analog paths, and use the manufacturer's reference circuit for decoupling and logic-interface implementation.
추천
Audio and Communication Signal Routing
The MAX399EGE can route multiple low-level analog sources in audio, communication, or line-level interface equipment where channel matching and flat on-resistance are valuable. Its two 4:1 sections allow a compact design to share downstream amplifier or converter paths. Keep routing away from switching power stages and use a continuous reference plane to limit injected noise. Verify signal amplitude, bandwidth, slew-related performance, and input protection requirements in the manufacturer data sheet because those operating limits are not stated in the product summary.
추천
Data Converter Front End
The MAX399EGE can serve as a front-end selector ahead of an ADC or DAC, allowing one converter to sample or receive several analog sources. On-resistance below 100Ω is low enough for many low-impedance signal chains, while channel matching within 6Ω simplifies gain calibration across selected inputs. Place the multiplexer between the source connectors and converter input, maintain short traces, and check source settling requirements against the converter acquisition time. Validate kickback, charge injection, and switching transients using the manufacturer's test conditions before committing the layout.
추천
Industrial Control Analog Fan-Out
The MAX399EGE can route conditioned sensor outputs inside compact industrial control modules that need to connect several analog sources to one controller or monitoring channel. Its two independent 4:1 sections provide flexible source selection without duplicating front-end connectors. The 4x4 mm QFN package supports compact board layouts, while matched channel resistance improves consistency between measurement positions. Use protective networks for industrial transients, confirm the allowed analog signal range, and maintain a low-impedance ground path beneath the selected analog routes.
추천
추천 제품 요약
엔지니어링 참조 데이터: MAX399EGE — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MAX399EPE | MAX399EEE+ | DG508ADJ+ |
|---|---|---|---|---|
| Drop-In Compatibility | Reference MAX399EGE footprint | No; 16-PDIP footprint | No; 16-QSOP footprint | Not established |
주요 차별점
- Combines two independent 4:1 analog switches in one package (vs MAX398-family devices)
- Compact 4x4 mm QFN implementation (vs MAX399EPE)
- Low and closely matched channel resistance (vs MAX399EEE+)
설계 노트
Route the selected analog node as a short, continuous path between the MAX399EGE common terminal and the receiving converter or amplifier. Place the device near the source connectors and avoid forcing the signal through long traces around the board. Reference the MAX398/MAX399 pin-description table when assigning the common terminals and ensure that exposed-pad requirements, if applicable, follow the package drawing.
Include the on-resistance below 100Ω in the gain and source-impedance budget of every selected channel. The 6Ω channel-matching limit and 11Ω maximum variation across the specified analog signal range can help define calibration and error budgets. For high-impedance sources, recalculate attenuation and settling because the mux resistance may interact with capacitance, leakage, and converter acquisition time.
Do not treat MAX399EPE or MAX399EEE+ as drop-in replacements for MAX399EGE. MAX399EPE uses a 16-PDIP package and MAX399EEE+ uses a 16-QSOP package, so either choice requires different PCB lands. Likewise, verify pin functions, control polarity, supply limits, and signal ratings before approving any DG-series or other cross-brand candidate.
규정 준수 정보
The manufacturer product page identifies MAX399 as a production device, but no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was included in the available product information.