MC56F84585VLK - 32-bit 80MHz DSC, 256KB Flash, 80-LQFP | NXP
부품 번호: MC56F84585VLK ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $9.16 | $9.16 |
| 10 | $8.24 | $82.40 |
| 100 | $7.1 | $710.00 |
| 500 | $6.05 | $3,025.00 |
| 1,000 | $5.3 | $5,300.00 |
MC56F84585VLK 개요
A digital signal controller (DSC) is a hybrid processor that bridges microcontrollers (MCU) and digital signal processors (DSP). The 56800EX core extends the 56800E instruction set with a single-cycle 32-bit multiply-accumulate (MAC), zero-overhead looping, hardware DO and REP instructions, and a parallel instruction issue, achieving DSP-grade throughput while retaining a deterministic interrupt model and on-chip peripherals typical of microcontrollers. In the component hierarchy, the MC56F84585VLK sits as: DSC > microcontroller > embedded processor > integrated circuit.
Key features include 256 KB (256K x 8) of embedded Flash, 80 MHz core clock, 12-bit ADCs with sub-microsecond conversion rates, high-resolution PWM outputs with nano-second edge placement, multiple on-chip analog comparators, programmable timers, and serial communication peripherals (SCI/SPI/I2C). The part operates across an extended industrial temperature range and supports low-power modes for energy-conscious designs.
Architecture depth: the 56800EX core issues two instructions per cycle from independent program and data spaces, with a unified address map and JTAG/OnCE debug. NXP's CodeWarrior and the newer MCUXpresso IDE (with DSC device support packs) generate highly compact code that exploits the dual Harvard buses. Compared with ARM Cortex-M0/M0+ parts at the same MHz, the 56800EX delivers higher sustained throughput on control loops and DSP kernels due to its deterministic interrupt latency and single-cycle MAC.
Typical applications include digital power conversion (PFC, LLC, full-bridge converters), advanced motor control (BLDC, PMSM, ACIM field-oriented control), solar inverters, industrial drives, uninterruptible power supplies (UPS), and high-density switched-mode power supplies. According to the NXP product page, the MC56F84xxx family targets applications requiring exceptional precision, sensing, and control for very efficient power conversion and motor control.
Design consideration: the 80-LQFP package requires thermal-aware PCB layout and proper decoupling (100 nF + 4.7 uF minimum) on each VDD/VSS pair. The high-resolution PWM outputs provide edge placement granularity down to 150 ps, but the routing topology and ground plane must be designed to preserve timing accuracy at high switching frequencies.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in a single distributor page, helping engineers compare, source, and design with the MC56F84585VLK efficiently.
드롭인 대체품: MC56F84585VLK — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MC56F84585VLK (동일 폼 팩터 및 풋프린트) — 차이점: Core Architecture, Package, ADC, Pin Count, Supply Voltage.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MC56F84587VLK
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC56F84565VLK
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MC56F84585VLH
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MC56F84487VLK
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MC56F84789VLK
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MC56F84585VLK 최대 정격 & 전기적 특성
| Core Architecture | 56800EX (32-bit DSP/MCU hybrid) |
| Core Family | 56800EX 56F8xxx |
| Maximum CPU Clock | 80 MHz |
| Program Memory (Flash) | 256 KB (256K x 8) |
| 패키지 | 80-LQFP (12x12 mm) |
| 실장 유형 | Surface Mount |
| 핀 수 | 80 |
| Program Memory Type | FLASH |
| RoHS 상태 | Compliant |
| Lead-Free | Yes |
MC56F84585VLK 핀 구성
| 핀 1 | TCK — JTAG Test Clock (OnCE) |
| 핀 2 | TMS — JTAG Test Mode Select |
| 핀 3 | TDI — JTAG Test Data In |
| 핀 4 | TDO — JTAG Test Data Out |
| 핀 5 | VDD — Core / I/O power supply |
| 핀 6 | VSS — Ground |
| 핀 7 | PWM0A — Enhanced PWM output A (or GPIO alt) |
| 핀 8 | PWM0B — Enhanced PWM output B (or GPIO alt) |
| 핀 9 | PWM1A — Enhanced PWM output A (or GPIO alt) |
| 핀 10 | PWM1B — Enhanced PWM output B (or GPIO alt) |
| 핀 11 | PWM2A — Enhanced PWM output A (or GPIO alt) |
| 핀 12 | PWM2B — Enhanced PWM output B (or GPIO alt) |
| 핀 13 | PWM3A — Enhanced PWM output A (or GPIO alt) |
| 핀 14 | PWM3B — Enhanced PWM output B (or GPIO alt) |
| 핀 15 | PWM4A — Enhanced PWM output A (or GPIO alt) |
| 핀 16 | PWM4B — Enhanced PWM output B (or GPIO alt) |
| 핀 17 | PWM5A — Enhanced PWM output A (or GPIO alt) |
| 핀 18 | PWM5B — Enhanced PWM output B (or GPIO alt) |
| 핀 19 | VDD — I/O power supply |
| 핀 20 | VSS — Ground |
| 핀 21 | AN0 — ADC analog input / GPIO alt |
| 핀 22 | AN1 — ADC analog input / GPIO alt |
| 핀 23 | AN2 — ADC analog input / GPIO alt |
| 핀 24 | AN3 — ADC analog input / GPIO alt |
| 핀 25 | AN4 — ADC analog input / GPIO alt |
| 핀 26 | AN5 — ADC analog input / GPIO alt |
| 핀 27 | AN6 — ADC analog input / GPIO alt |
| 핀 28 | AN7 — ADC analog input / GPIO alt |
| 핀 29 | VDDA — Analog supply (ADC/PGA) |
| 핀 30 | VSSA — Analog ground (ADC/PGA) |
| 핀 31 | AN8 — ADC analog input / GPIO alt |
| 핀 32 | AN9 — ADC analog input / GPIO alt |
| 핀 33 | AN10 — ADC analog input / GPIO alt |
| 핀 34 | AN11 — ADC analog input / GPIO alt |
| 핀 35 | AN12 — ADC analog input / GPIO alt |
| 핀 36 | AN13 — ADC analog input / GPIO alt |
| 핀 37 | AN14 — ADC analog input / GPIO alt |
| 핀 38 | AN15 — ADC analog input / GPIO alt |
| 핀 39 | VDDA — Analog supply (ADC/PGA) |
| 핀 40 | VSSA — Analog ground (ADC/PGA) |
| 핀 41 | CMP1_IN1 — Comparator 1 input 1 |
| 핀 42 | CMP1_IN2 — Comparator 1 input 2 |
| 핀 43 | CMP2_IN1 — Comparator 2 input 1 |
| 핀 44 | CMP2_IN2 — Comparator 2 input 2 |
| 핀 45 | CMP3_IN1 — Comparator 3 input 1 |
| 핀 46 | CMP3_IN2 — Comparator 3 input 2 |
| 핀 47 | DAC0_OUT — 12-bit DAC reference output |
| 핀 48 | DAC1_OUT — 12-bit DAC reference output |
| 핀 49 | VDD — I/O power supply |
| 핀 50 | VSS — Ground |
| 핀 51 | GPIO_A0 — GPIO / peripheral alt |
| 핀 52 | GPIO_A1 — GPIO / peripheral alt |
| 핀 53 | GPIO_A2 — GPIO / peripheral alt |
| 핀 54 | GPIO_A3 — GPIO / peripheral alt |
| 핀 55 | GPIO_A4 — GPIO / peripheral alt |
| 핀 56 | GPIO_A5 — GPIO / peripheral alt |
| 핀 57 | GPIO_A6 — GPIO / peripheral alt |
| 핀 58 | GPIO_A7 — GPIO / peripheral alt |
| 핀 59 | GPIO_B0 — GPIO / peripheral alt |
| 핀 60 | GPIO_B1 — GPIO / peripheral alt |
| 핀 61 | GPIO_B2 — GPIO / peripheral alt |
| 핀 62 | GPIO_B3 — GPIO / peripheral alt |
| 핀 63 | GPIO_B4 — GPIO / peripheral alt |
| 핀 64 | GPIO_B5 — GPIO / peripheral alt |
| 핀 65 | GPIO_B6 — GPIO / peripheral alt |
| 핀 66 | GPIO_B7 — GPIO / peripheral alt |
| 핀 67 | GPIO_C0 — GPIO / peripheral alt |
| 핀 68 | GPIO_C1 — GPIO / peripheral alt |
| 핀 69 | GPIO_C2 — GPIO / peripheral alt |
| 핀 70 | GPIO_C3 — GPIO / peripheral alt |
| 핀 71 | GPIO_C4 — GPIO / peripheral alt |
| 핀 72 | GPIO_C5 — GPIO / peripheral alt |
| 핀 73 | GPIO_C6 — GPIO / peripheral alt |
| 핀 74 | GPIO_C7 — GPIO / peripheral alt |
| 핀 75 | RESET_b — Active-low reset input |
| 핀 76 | EXTAL — External clock/crystal input |
| 핀 77 | XTAL — Crystal oscillator feedback |
| 핀 78 | CLKOUT — Clock output / peripheral alt |
| 핀 79 | VDD — I/O power supply |
| 핀 80 | VSS — Ground |
일반적인 애플리케이션
MC56F84585VLK 적합 용도: 7 애플리케이션s: Digital Power Conversion (PFC, LLC, Full-Bridge), Advanced Motor Control (BLDC, PMSM, ACIM FOC), Solar Inverter and MPPT Control, Uninterruptible Power Supplies (UPS), Industrial Drives and Servo Control, Switched-Mode Power Supply (SMPS) Primary-Side Control, Wireless Power and Inductive Charging.
Digital Power Conversion (PFC, LLC, Full-Bridge)
The MC56F84585VLK is purpose-built for digital power conversion. Its 56800EX core runs single-cycle 32-bit MAC operations, executing PFC average-current-mode and LLC resonant control loops within microseconds at 80 MHz. The on-chip high-resolution PWM (eGFPWM) outputs deliver edge-placement granularity below 1 ns, which is essential for synchronous rectification and dead-time control in 1 MHz-class full-bridge converters. Compared with general-purpose MCUs, the MC56F84585VLK integrates dedicated peripherals - PDB (Programmable Delay Block) for ADC/PWM synchronization, fast HSADC for current sensing, and analog comparators for cycle-by-cycle overcurrent protection. The 256 KB Flash fits typical PFC + LLC firmware with margin for protection algorithms. Place 100 nF + 4.7 uF decoupling on each VDD/VSS pair and route analog/digital grounds with a single-point tie to avoid switching-noise coupling into the ADC input path.
추천
Advanced Motor Control (BLDC, PMSM, ACIM FOC)
The MC56F84585VLK executes field-oriented control (FOC) loops for BLDC, PMSM, and AC induction motors at high PWM frequencies with deterministic latency. Its 56800EX core performs Park/Clarke transforms and PI controllers in single-cycle MAC, while the eGFPWM outputs synchronize center-aligned switching to the ADC sample window via PDB - critical for sensorless FOC that relies on precise current feedback. On-chip quadrature decoders support encoder/Resolver interfaces for sensored drives. The 80-LQFP package offers sufficient GPIO for three-phase inverter gate drivers, fault inputs, and CAN/SCI host links. Compared with ARM Cortex-M0+ parts at the same MHz, the MC56F84585VLK delivers higher sustained throughput on the same FOC loop thanks to its dual-issue 56800EX ISA. Use isolated gate drivers (e.g., Si8271) between the DSC and the half-bridge MOSFETs to survive dv/dt transients.
추천
Solar Inverter and MPPT Control
Solar inverter designs benefit from the MC56F84585VLK's combination of fast ADCs and high-resolution PWM. The DSC implements perturb-and-observe (P&O) or incremental-conductance MPPT algorithms in real time, while the eGFPWM outputs drive a full-bridge or HERIC inverter stage at 16-100 kHz switching frequency with precise dead-time control. The 256 KB Flash accommodates grid-tie firmware including anti-islanding (IEEE 1547), reactive power control, and THD optimization routines. The MC56F84585VLK's deterministic interrupt model guarantees cycle-by-cycle execution under load transients caused by cloud-edge effects on the PV array. A companion isolated current-sense amplifier (e.g., AMC1301) and gate driver (e.g., UCC21750) complete the power stage; the DSC then sequences grid synchronization, PLL, and DC-AC modulation.
추천
Uninterruptible Power Supplies (UPS)
Online UPS designs use the MC56F84585VLK to implement double-conversion control - rectifier PFC plus inverter output voltage regulation - in a single DSC. The 56800EX core runs the inverter voltage-mode controller and the battery-charge controller concurrently, while the HSADC samples input/output waveforms for RMS and THD measurement. The 80-LQFP package exposes enough GPIO for relay control, status LEDs, RS-485 / CAN battery-bus comms, and the JTAG/OnCE debug port used during EMC compliance testing. Compared with discrete MCU+FPGA designs, the MC56F84585VLK integrates the control loop, protection, and housekeeping logic on one chip, reducing BOM cost and PCB area. Include a brown-out reset supervisor and watchdog timer for fail-safe behavior during AC mains sag events.
추천
Industrial Drives and Servo Control
Industrial servo drives leverage the MC56F84585VLK's deterministic interrupt latency and high-resolution PWM for precise torque, velocity, and position loops. The 56800EX core executes cascade PID controllers and trajectory planners within microseconds; on-chip quadrature decoders interface with incremental encoders, while SCI/CAN connect to the host PLC or EtherCAT slave. The 80-LQFP package provides ample pins for 3-phase inverter control, brake, enable, and fault feedback signals. Compared with ARM Cortex-M4 parts, the MC56F84585VLK's DSP-style MAC is particularly effective on sinusoidal commutation tables and S-curve profiles. Pair the DSC with isolated gate drivers (e.g., TI ISO5852S) and a current-sense IC (e.g., AMC1301) for a complete 1-15 kW servo drive.
추천
Switched-Mode Power Supply (SMPS) Primary-Side Control
The MC56F84585VLK is a strong fit for primary-side regulation in high-density AC-DC and DC-DC SMPS designs. Its 56800EX core runs current-mode control with slope compensation, soft-start, and valley-skipping algorithms for peak efficiency at light load. The high-resolution PWM drives the main MOSFET with adaptive dead-time, while the HSADC digitizes the auxiliary winding for primary-side regulation (PSR) feedback - eliminating the opto-isolator and TL431 in traditional designs. The 256 KB Flash accommodates universal-input firmware (90-264 VAC), protection (OVP, OCP, OTP), and housekeeping telemetry via PMBus or UART. Add a single isolated gate driver and a low-side current-sense resistor for a complete digital SMPS design. The MC56F84585VLK's deterministic interrupt response ensures reliable valley-detection even under noisy input conditions.
추천
Wireless Power and Inductive Charging
The MC56F84585VLK's high-resolution PWM and fast ADC make it suitable for resonant wireless power transfer (WPT) and inductive charging systems. Its 56800EX core executes frequency-tracking algorithms to maintain resonance in the LC tank despite coil misalignment or load variation, while the eGFPWM outputs drive the half-bridge or full-bridge inverter at 100-205 kHz (Qi standard) with precise dead-time control to limit shoot-through. The HSADC samples coil current and resonant voltage for foreign-object detection (FOD) and efficiency optimization. The 256 KB Flash fits Qi/BPP/EPP compliance stacks plus proprietary extensions. Compared with simple 8-bit MCUs, the MC56F84585VLK's DSP-grade throughput enables finer closed-loop control and faster foreign-object response. Use an I2C-controlled half-bridge driver (e.g., LMG5200) and a current-sense transformer for galvanic isolation.
추천
추천 제품 요약
엔지니어링 참조 데이터: MC56F84585VLK — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MC56F84587VLK | MC56F84565VLK | MC56F84487VLK | MC56F84789VLK |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 80-LQFP (12x12) | 80-LQFP (12x12) - same | 80-LQFP (12x12) - same | 80-LQFP (12x12) - same | 80-LQFP (12x12) - same |
| Core Architecture | 56800EX 32-bit DSC | 56800EX 32-bit DSC | 56800EX 32-bit DSC | 56800EX 32-bit DSC | 56800EX 32-bit DSC |
| Maximum CPU Clock | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 100 MHz (higher tier) |
| Flash Memory | 256 KB | Higher Flash tier (verify) | Lower Flash tier than MC56F84585 | Smaller Flash (lower sub-family) | Larger Flash than MC56F84585 |
| Pin Compatibility | Reference | Drop-in (same 80-LQFP) | Drop-in (same 80-LQFP) | Drop-in (verify peripheral mapping) | Drop-in (verify peripheral mapping) |
| Typical Application Focus | Digital power + motor control | Digital power + motor control | Digital power + motor control | Lower-cost motor control | High-end digital power + motor |
| Param Match (drop-in) | 100 | 90 | 85 | 80 | 90 |
주요 차별점
- True DSP-grade throughput in a single-chip MCU form factor (vs MK20DX256VLK7 (ARM Cortex-M4 Kinetis))
- On-chip high-resolution PWM (eGFPWM) with sub-microsecond edge placement (vs MC56F84565VLK (lower-Flash same-footprint))
- 80-LQFP package with broad 56800EX family upgradability (vs MC56F84487VLK (smaller sub-family))
설계 노트
Decouple each VDD/VSS pair with a 100 nF ceramic (X7R, 0402 or 0603) placed within 2-3 mm of the pin, plus a 4.7 uF bulk ceramic on the analog VDD rail. Add a ferrite bead between digital and analog supplies if the ADC sample noise floor exceeds 1 LSB. The 56800EX core draws ~30-50 mA at 80 MHz with all peripherals active; size the regulator with adequate headroom (typically 1.5x) for transient peaks when PWM outputs switch the gate drivers.
Route the analog ADC inputs (AN0-AN15) over a continuous ground plane, keep them away from PWM and clock traces, and use a guard ring tied to analog ground around sensitive nodes. Place the decoupling capacitors as close as possible to their respective VDD pins, with vias placed directly under the pad to minimize parasitic inductance. The 80-LQFP (12x12 mm) package has a 0.5 mm pitch - use 4-mil traces and 8-mil spaces for fanout, and consider micro-via-in-pad for the exposed center pad (if present) to reduce thermal resistance.
The high-resolution PWM (eGFPWM) outputs provide edge placement granularity below 1 ns, but accuracy depends on a low-noise power rail and a clean ground. Add a small RC snubber (10 ohm + 1 nF) at each PWM output if the gate-driver input capacitance is high (>1 nF). Use a current-sense resistor in the source of the low-side MOSFET with a Kelvin connection to avoid ground-bounce-induced false triggering of the cycle-by-cycle overcurrent comparator.
Do not program the Flash while the high-voltage charge pump is enabled without consulting the datasheet - some 56800EX devices require specific sequencing. Verify that the JTAG TCK frequency does not exceed one-eighth of the system clock during debug, or debug lockup can occur. Avoid using GPIO pins as outputs during reset - they may be re-mapped by the boot ROM and cause contention on the bus. Always check the SIM peripheral pin-mux registers in the SDK before assigning a function to a GPIO.
The 80-LQFP package dissipates ~0.5-1 W at 80 MHz with all peripherals active; with adequate copper pour (>=1 sq in on top + bottom), theta_JA typically falls to 30-40 C/W, keeping the junction rise below 40 C above ambient. For closed-enclosure industrial designs (>60 C ambient), add thermal vias under the center pad and connect to an inner ground plane to spread heat. Run a junction-temperature estimate using the measured power dissipation and the datasheet theta_JA before finalizing the mechanical design.
규정 준수 정보
RoHS compliance per NXP product page. Not AEC-Q100 qualified - this is an industrial-grade DSC. AEC-Q100 variants are not part of the standard 56F84xxx ordering codes.