MMA6341LT - ±3g/±9g 2-Axis Low-g Accelerometer | NXP
부품 번호: MMA6341LT ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $7.2 | $7.20 |
| 10 | $6.5 | $65.00 |
| 100 | $5.75 | $575.00 |
| 500 | $5.2 | $2,600.00 |
| 1,000 | $4.65 | $4,650.00 |
| 3,000 | $4.1 | $12,300.00 |
MMA6341LT 개요
An accelerometerometer is a micro-electromechanical sensor (MEMS) that transduces gravitational or inertial acceleration into a proportional electrical signal. The MMA6341LT belongs to the capacitive-sensing MEMS family, in which a proof mass moves between fixed interdigitated electrodes and the change in capacitance is read out by an on-chip ASIC. In the broader hierarchy it sits under: accelerometerter -> inertial sensor -> MEMS device -> semiconductor sensor, and it is typically used as a tilt/inclination or motion-front-end in a power-management or user-interface subsystem.
Key features include selectable ±3 g / ±9 g full-scale range via the g-Select pin, ±5 % sensitivity trim accuracy over temperature, 1-pole low-pass filter with 400 Hz bandwidth, ratiometric analog output, and an ultra-low 3 µA Sleep Mode current. The 14-pin LGA (3x5) package measures only 3 mm × 5 mm × 1 mm and provides a robust industrial temperature range of -40 °C to +85 °C.
The MMA6341LT uses Freescale/NXP's high-aspect-ratio micromachined sense element with a BiCMOS signal-chain ASIC, which yields better than 5 % sensitivity accuracy, factory-set zero-g offset (no external trim components required), and a low ratiometric output noise density suitable for tilt and motion-detection bandwidths.
Typical applications include portable consumer-electronics tilt and orientation (eBook readers, remote controls, gaming controllers), hard-disk drive free-fall detection, motion-activated user interfaces, vibration monitoring in industrial equipment, and anti-tamper / inclinometer modules. Because the output is ratiometric to VDD, designers can read it directly with an MCU ADC without an external precision reference.
When designing with this device, place 0.1 µF decoupling capacitors as close as possible to the VDD pin and keep the g-Select pin tied either to GND or VDD with a defined logic level (never floating). The exposed pad on the LGA must be soldered to the PCB ground plane to provide mechanical stability and thermal dissipation.
This page synthesizes distributor pricing, drop-in alternatives in the same 14-LGA footprint, and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: MMA6341LT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MMA6340LT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MMA6344LT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MMA7331LT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MMA7341LT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MMA6351LT
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MMA7361LT
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MMA6341LT 최대 정격 & 전기적 특성
| 센서 유형 | Accelerometer, 2-axis (X, Y) |
| Sensing Technology | Capacitive MEMS |
| Full-Scale Range | ±3 g, ±9 g (selectable via g-Select) |
| Sensitivity (3 g mode) | 550 mV/g (typical at 3.0 V) |
| Sensitivity (9 g mode) | 180 mV/g (typical at 3.0 V) |
| 출력 유형 | Analog, ratiometric to VDD |
| Bandwidth | 400 Hz (1-pole LPF) |
| 공급 전압 | 2.2 V to 3.6 V |
| Supply Current (Normal) | 500 µA (typical) |
| Supply Current (Sleep) | < 3 µA |
| Zero-g Offset (factory trim) | ±50 mg (typical) |
| Sensitivity Trim Accuracy | ±5 % (over temperature) |
| 동작 온도 | -40 °C to +85 °C |
| 패키지 | 14-LGA (3 mm × 5 mm × 1 mm) |
| 실장 유형 | Surface Mount (LGA, exposed pad) |
| MSL 레벨 | 3 (per JEDEC J-STD-020) |
| RoHS 상태 | Compliant (lead-free) |
| g-Select Logic Input | Yes (selects ±3 g / ±9 g full-scale) |
MMA6341LT 핀 구성
| 핀 1 | NC — Not connected (per datasheet) |
| 핀 2 | NC — Not connected (per datasheet) |
| 핀 3 | NC — Not connected (per datasheet) |
| 핀 4 | NC — Not connected (per datasheet) |
| 핀 5 | NC — Not connected (per datasheet) |
| 핀 6 | XOUT — X-axis analog output (ratiometric to VDD) |
| 핀 7 | YOUT — Y-axis analog output (ratiometric to VDD) |
| 핀 8 | g-Select — Range select logic input: 0 = ±3 g, 1 = ±9 g |
| 핀 9 | NC — Not connected (per datasheet) |
| 핀 10 | NC — Not connected (per datasheet) |
| 핀 11 | NC — Not connected (per datasheet) |
| 핀 12 | VDD — Power supply (2.2 V to 3.6 V) |
| 핀 13 | GND — Ground reference |
| 핀 14 | NC — Not connected (per datasheet) |
일반적인 애플리케이션
MMA6341LT 적합 용도: 6 애플리케이션s: Tilt & Orientation Sensing in Consumer Electronics, Hard-Disk Drive Free-Fall Detection, Portable Medical Motion & Activity Monitors, Industrial Vibration & Inclinometer Modules, Gaming & Motion Controller Input, Anti-Tamper & Security Orientation Detection.
Tilt & Orientation Sensing in Consumer Electronics
The MMA6341LT is well suited to tilt and orientation sensing in portable consumer devices such as eBook readers, remote controls and gaming controllers. Its ±3 g low-g mode gives 550 mV/g sensitivity at 3.0 V, so a small tilt of 30° produces a measurable ~440 mV swing at the analog output, easily read by an MCU ADC. The ratiometric output tracks VDD/2 as the zero-g reference, simplifying single-supply designs, while the 3 µA Sleep Mode keeps idle battery drain negligible. The 14-LGA (3x5 mm) package fits inside space-constrained handheld enclosures. Designers typically place the part near the device's center of gravity with the LGA exposed pad soldered to ground for mechanical stability.
추천
Hard-Disk Drive Free-Fall Detection
The MMA6341LT's ±9 g full-scale mode and 400 Hz low-pass bandwidth make it appropriate for HDD free-fall detection, where the drive must park its heads within milliseconds when the laptop is dropped. The MMA6341LT generates an analog voltage proportional to the deceleration that can be threshold-detected by a single comparator or an MCU ADC channel; the g-Select pin can be hard-wired to VDD for full ±9 g coverage. Because the part draws only 500 µA active and 3 µA in Sleep, it has negligible impact on battery life. Its LGA footprint fits beneath the HDD connector area without adding to the laptop's z-height.
추천
Portable Medical Motion & Activity Monitors
Battery-powered medical wearables and patient-activity monitors use the MMA6341LT to detect posture changes, fall events and ambulation. Its ±3 g range covers normal human-motion acceleration (typical walking cadence is <2 g peak), and the ratiometric output simplifies interface to medical-grade low-power MCUs. The 500 µA active current is acceptable during measurement windows, while Sleep Mode at 3 µA extends battery life between samples. According to the NXP MMA6341L datasheet, the part's industrial -40 °C to +85 °C range also handles clinical-environment temperature swings. The exposed LGA pad provides a stable reference for accurate tilt readings even under mechanical vibration.
추천
Industrial Vibration & Inclinometer Modules
The MMA6341LT's ±3 g / ±9 g selectable range and 400 Hz analog bandwidth are sufficient for low-frequency industrial vibration monitoring and inclinometer modules used on construction equipment, agricultural machinery and solar trackers. Its capacitive MEMS architecture is more rugged than piezo alternatives in high-shock environments, and the factory-trimmed zero-g offset removes the need for field calibration. The ratiometric analog output can be routed through a long shielded cable to a centralized PLC analog input, or read locally by a microcontroller. The 14-LGA package's exposed pad helps dissipate thermal stress from -40 °C to +85 °C operating swings, while the 500 µA supply current suits 24 V-loop-powered sensor heads when paired with a 3.3 V LDO.
추천
Gaming & Motion Controller Input
Game controllers and motion-sensing remote controls leverage the MMA6341LT for tilt-to-steer and motion-gesture inputs. The ±3 g low-g mode gives the high 550 mV/g sensitivity needed to detect subtle wrist tilts, while the ±9 g mode captures fast flick gestures without saturating. The analog output can be sampled at >1 kHz by the controller MCU, well above the part's 400 Hz -3 dB bandwidth, providing low-latency gesture recognition. Sleep Mode at 3 µA helps the controller meet battery-life targets between play sessions, and the small 14-LGA (3x5 mm) footprint fits inside a slim handset. Designers typically route the LGA exposed pad to ground for stable reference and add a 0.1 µF decoupling cap on VDD.
추천
Anti-Tamper & Security Orientation Detection
The MMA6341LT is used in security devices (ATM anti-tamper modules, smart-meter tilt alarms, anti-theft sensors for high-value equipment) to detect unauthorized reorientation or removal. The ±3 g / ±9 g selectable range allows the device to discriminate between small tilts and violent impacts, and the analog ratiometric output can be read by a low-cost comparator to trigger an alarm without waking the main MCU. Sleep Mode at 3 µA supports multi-year battery life on coin-cell-powered wireless anti-tamper tags. The 14-LGA exposed pad mechanically couples the sense element to the PCB, suppressing false alarms from vibration, while the industrial -40 °C to +85 °C range handles outdoor enclosures.
추천
추천 제품 요약
엔지니어링 참조 데이터: MMA6341LT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MMA6340LT | MMA6344LT | MMA7331LT | MMA7341LT | MMA6351LT |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 14-LGA (3x5 mm) | 14-LGA (3x5 mm) - same | 14-LGA (3x5 mm) - same | 14-LGA (3x5 mm) - same | 14-LGA (3x5 mm) - same | 14-LGA (3x5 mm) - same |
| Axes | X, Y (2-axis) | X, Y (2-axis) | Z (1-axis) | X, Y (2-axis) | X, Y (2-axis) | X, Y (2-axis) |
| Full-Scale Range | ±3 g / ±9 g (g-Select) | ±1.5 g / ±6 g | ±3 g / ±9 g (Z only) | ±4 g / ±12 g / ±16 g | ±3 g / ±11 g | ±1.5 g / ±6 g |
| Supply Voltage | 2.2 V to 3.6 V | 2.2 V to 3.6 V | 2.2 V to 3.6 V | 2.2 V to 3.6 V | 2.2 V to 3.6 V | 2.2 V to 3.6 V |
| Sleep Mode Current | < 3 µA | < 3 µA | < 3 µA | < 3 µA | < 3 µA | < 3 µA |
| Output Type | Analog, ratiometric | Analog, ratiometric | Analog, ratiometric | Analog, ratiometric | Analog, ratiometric | Analog, ratiometric |
| Bandwidth | 400 Hz | 400 Hz | 400 Hz | 400 Hz (X, Y); 300 Hz (Z) | 400 Hz | 400 Hz |
주요 차별점
- Selectable ±3 g / ±9 g range via single logic pin (vs MMA6340LT)
- Pin-compatible Z-axis variant for layout reuse (vs MMA6344LT)
- Wider high-g range than closest sibling (vs MMA6340LT)
설계 노트
Place a 0.1 µF ceramic decoupling capacitor as close as possible to the VDD pin (pin 12) and a 1 µF bulk capacitor within 5 mm of the part. The analog output is ratiometric to VDD, so any ripple on VDD appears directly on the XOUT/YOUT outputs. Use a low-noise LDO (e.g., NXP TLV1117 or TPS7A02 family) rather than a switching regulator for VDD to preserve the part's noise floor for tilt applications.
The 14-LGA (3x5 mm) package has an exposed die pad on the underside that must be soldered to a continuous PCB ground plane. This pad provides the electrical reference for the capacitive MEMS sense element and mechanical coupling to suppress PCB-bend-induced offset. Use a 3x5 mm copper land pattern with at least 6 thermal-via array to inner ground plane. Place no signal traces under the LGA footprint - keep-out is required by the NXP datasheet.
Route XOUT and YOUT as differential-style guarded traces, with ground fill on both sides and a ground-guard via stitch every 5 mm. Keep the traces short (≤25 mm) to minimize capacitive loading on the high-impedance analog outputs. Avoid routing XOUT/YOUT parallel to switching-power or motor-drive traces - the MEMS output bandwidth (400 Hz) is low, but switching transients can couple through VDD and produce rectified offset errors. Reference the NXP MMA6341L datasheet section on PCB layout for a reference design.
Do not leave the g-Select pin (pin 8) floating - tie it firmly to VDD (logic 1, ±9 g mode) or GND (logic 0, ±3 g mode) with a defined driver. A floating g-Select can cause the part to operate in an undefined mode with non-guaranteed sensitivity. Do not exceed the 3.6 V absolute-maximum VDD rating; transients above 4 V can permanently damage the ASIC. Avoid hand-soldering the LGA - use a reflow profile per JEDEC J-STD-020 MSL3 (the part is moisture-sensitive and requires bake-out if the factory seal has been open >168 hours).
규정 준수 정보
RoHS compliant and lead-free per NXP product page and DigiKey listing. Industrial -40 °C to +85 °C temperature grade (not AEC-Q100 automotive qualified). MSL 3 moisture sensitivity level per JEDEC J-STD-020.
