PIC16C716-04I/SS - 8-Bit 4MHz MCU, 3.5KB OTP, 20-SSOP | Microchip
부품 번호: PIC16C716-04I/SS ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $3.92 | $3.92 |
| 10 | $3.53 | $35.30 |
| 100 | $2.97 | $297.00 |
| 500 | $2.65 | $1,325.00 |
| 1,000 | $2.41 | $2,410.00 |
PIC16C716-04I/SS 개요
A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (program + data), and programmable I/O peripherals on one die, allowing engineers to implement embedded control logic with a minimum of external components. The PIC16C716 belongs to the broader category of 8-bit microcontrollers (8-bit -> MCU -> embedded controller -> semiconductor), using Microchip's RISC instruction set with 35 single-word instructions. This architecture is widely used in automotive, industrial, appliance, and consumer applications where deterministic real-time control, low power, and compact code density are required.
Key features of the PIC16C716-04I/SS include an operating speed of DC to 4 MHz (the "-04" speed grade), up to 7 internal/external interrupt sources, an 8-level hardware stack, and a 4-channel 8-bit ADC that enables direct interface with analog sensors without external ADC ICs. The two additional timers and CCP module provide flexible PWM generation and input-capture functions for motor control, signal measurement, and timing applications.
The PIC16C716 architecture is based on a Harvard-bus RISC core, separating program memory (14-bit wide OTP) from data memory (8-bit wide SRAM) to enable single-cycle instruction execution except for program branches (2 cycles). This pipelined design, combined with the 200 ns instruction cycle at 4 MHz, gives the MCU deterministic throughput well suited to real-time control loops. The industrial temperature grade ("-I") supports an operating range of -40°C to +85°C.
Typical applications include sensor signal conditioning, low-cost motor control (small DC fans, solenoids), automotive body controllers, appliance control boards, and battery-powered instruments requiring OTP programmability for cost-effective mid-volume production runs. The 20-SSOP footprint also makes it attractive for compact consumer designs.
When designing with this device, note that OTP memory is one-time programmable and cannot be re-flashed; for field-updatable firmware, consider the flash-based PIC16F716 (same 20-SSOP pinout). Always use Microchip's MPLAB X IDE with a compatible programmer (e.g., PICkit 3/4, ICD) for code development.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone - giving engineers and buyers a faster path from selection to board bring-up.
드롭인 대체품: PIC16C716-04I/SS — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC16C716-04I/SS (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Timers, Operating Temperature, Package, Mounting Type.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC16C716-04/SS
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC16C716T-04I/SS
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC16C716T-04E/SS
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC16F716-I/SS
✅ 드롭인✓ 재고 있음
$1.58 / 개
데이터시트 보기 →PIC16C716-04I/SS 최대 정격 & 전기적 특성
| Core | PIC 16C (8-bit RISC) |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 3.5 KB (2K x 14) |
| RAM Size | 128 bytes |
| CPU Speed | 4 MHz |
| Instruction Cycle | 200 ns |
| Number of I/O Pins | 13 |
| ADC | 4-channel, 8-bit |
| Timers | 2 additional (plus WDT) |
| Capture/Compare/PWM | 1 CCP module |
| Operating Voltage (Vcc) | 2.5 V to 5.5 V (typical 5 V) |
| 동작 온도 | -40 °C to +85 °C (Industrial grade) |
| Instruction Set | 35 single-word instructions |
| Interrupt Sources | Up to 7 internal/external |
| 패키지 | 20-SSOP (5.30 mm body width) |
| 실장 유형 | Surface Mount |
| MSL 레벨 | 1 (unlimited) |
PIC16C716-04I/SS 핀 구성
| 핀 1 | RA5/MCLR/VPP — Master Clear (reset) input / programming voltage |
| 핀 2 | RA0/AN0 — PORTA bit 0 / Analog input channel 0 |
| 핀 3 | RA1/AN1 — PORTA bit 1 / Analog input channel 1 |
| 핀 4 | RA2/AN2 — PORTA bit 2 / Analog input channel 2 |
| 핀 5 | RA3/AN3/VREF — PORTA bit 3 / Analog input channel 3 / Voltage reference |
| 핀 6 | RA4/T0CKI — PORTA bit 4 / Timer 0 clock input |
| 핀 7 | RA6/OSC2/CLKOUT — PORTA bit 6 / Oscillator crystal output / Clock out |
| 핀 8 | RA7/OSC1/CLKIN — PORTA bit 7 / Oscillator crystal input / External clock in |
| 핀 9 | RC0 — PORTC bit 0 |
| 핀 10 | RC1 — PORTC bit 1 |
| 핀 11 | RC2/CCP1 — PORTC bit 2 / Capture/Compare/PWM channel 1 |
| 핀 12 | RC3 — PORTC bit 3 |
| 핀 13 | RC4 — PORTC bit 4 |
| 핀 14 | RC5 — PORTC bit 5 |
| 핀 15 | RC6 — PORTC bit 6 |
| 핀 16 | RC7 — PORTC bit 7 |
| 핀 17 | RB0/INT — PORTB bit 0 / External interrupt |
| 핀 18 | RB1 — PORTB bit 1 |
| 핀 19 | VSS — Ground |
| 핀 20 | VDD — Positive supply voltage (2.5 V to 5.5 V) |
일반적인 애플리케이션
PIC16C716-04I/SS 적합 용도: 6 애플리케이션s: Automotive Body Controllers, Sensor Interface Modules, Small Motor / Fan Speed Control, Consumer Appliance Control, Battery-Powered Instrumentation, Industrial Timer / Sequencer.
Automotive Body Controllers
The PIC16C716-04I/SS fits automotive body and lighting control modules thanks to its 4-channel 8-bit ADC for analog sensor input, 13 GPIO pins for switches and relay drivers, and CCP module for PWM dimming. Its 4 MHz CPU with 200 ns instruction cycle delivers deterministic real-time response for body-electronics tasks like seat control, mirror adjustment, and ambient lighting, while the industrial temperature grade (-40°C to +85°C) handles under-dash thermal environments. The 3.5 KB OTP memory holds compact application firmware for these price-sensitive modules, and the small 20-SSOP footprint (5.30 mm body) enables placement in tight housing.
추천
Sensor Interface Modules
The PIC16C716-04I/SS's integrated 4-channel 8-bit ADC and 13 GPIO make it ideal for low-cost sensor interface modules reading temperature, light, humidity, or potentiometer signals. The 4 MHz core and 200 ns instruction cycle deliver 5 MIPS, sufficient for sampling four analog channels at hundreds of Hz, computing averages, and transmitting over UART or I/O. The 128-byte RAM is adequate for small data buffers, and the OTP memory prevents accidental firmware erasure in field-deployed industrial sensors. Power consumption is low, supporting battery-powered remote sensor nodes.
추천
Small Motor / Fan Speed Control
The PIC16C716-04I/SS is well suited for small DC motor or fan speed control using its on-chip CCP module for PWM generation and 4-channel ADC for closed-loop tachometer feedback. The 200 ns instruction cycle at 4 MHz allows precise PWM duty-cycle updates (8-bit resolution at standard PWM frequency), while the 13 GPIO pins accommodate direction-control relays, fault inputs, and status LEDs. The industrial temperature range supports appliance and industrial environments, and the compact 20-SSOP package fits inside small motor housings or fan assemblies.
추천
Consumer Appliance Control
The PIC16C716-04I/SS provides the right mix of integration and cost for white-goods and small-appliance controllers (coffee makers, toasters, washing-machine sub-modules, microwave keypads). The 4-channel ADC reads temperature, water level, or humidity sensors directly; the CCP module drives buzzers, triacs, or relays; and 13 GPIO scan keypads and LED indicators. OTP memory at 3.5 KB accommodates typical appliance state machines, and the 20-SSOP surface-mount package suits automated PCB assembly lines in high-volume consumer production.
추천
Battery-Powered Instrumentation
Low-power battery-powered instruments benefit from the PIC16C716-04I/SS's sleep/idle modes, wide 2.5 V to 5.5 V operating range, and on-chip ADC for direct sensor digitization without external ICs. The 4 MHz CPU and 128 B RAM are sufficient for data logging, slow-rate sampling, and UART/binary output to a host, while the industrial temperature range supports field-deployed measurement tools. OTP memory locks firmware at production time, protecting proprietary calibration constants. The 20-SSOP footprint allows compact handheld enclosures.
추천
Industrial Timer / Sequencer
The PIC16C716-04I/SS functions as a flexible industrial timer or sequencer, leveraging its two additional timers (beyond the WDT), CCP module, and 13 GPIO to drive relays, solenoids, and indicator LEDs in deterministic time-based sequences. The 4 MHz CPU with hardware stack and 7 interrupt sources handles multi-stage timing with minimal jitter, and the industrial temperature grade operates reliably in factory environments. The 20-SSOP package and OTP memory provide cost-effective deployment for fixed-function industrial controllers.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC16C716-04I/SS — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC16C716-04/SS | PIC16C716T-04I/SS | PIC16C716T-04E/SS | PIC16F716-I/SS |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-SSOP | 20-SSOP - same | 20-SSOP - same | 20-SSOP - same | 20-SSOP - same |
| Program Memory Type | OTP, 3.5 KB | OTP, 3.5 KB | OTP, 3.5 KB | OTP, 3.5 KB | Flash, 3.5 KB |
| CPU Speed | 4 MHz | 4 MHz | 4 MHz | 4 MHz | 20 MHz (downgrades to 4 MHz at lower VDD) |
| Temperature Grade | Industrial -40°C to +85°C | Commercial 0°C to +70°C | Industrial -40°C to +85°C | Extended -40°C to +125°C | Industrial -40°C to +85°C |
| ADC | 4-ch 8-bit | 4-ch 8-bit | 4-ch 8-bit | 4-ch 8-bit | 4-ch 8-bit |
| Field Reprogrammable | No (OTP) | No (OTP) | No (OTP) | No (OTP) | Yes (Flash, 100K cycles) |
| Distributor Stock (DigiKey/Mouser) | In stock | Active | Active | Active | Active, higher volume |
주요 차별점
- Integrated 4-channel 8-bit ADC eliminates external ADC chip (vs PIC16C715-I/SS)
- Industrial temperature grade -40°C to +85°C (vs PIC16C716-04/SS)
- Same-family PIC16 architecture enables firmware reuse across PIC16C/PIC16F (vs Non-PIC alternatives (e.g., ATmega, MSP430))
설계 노트
The PIC16C716-04I/SS operates from 2.5 V to 5.5 V on VDD (pin 20) with VSS (pin 19) as ground. Decouple VDD with a 100 nF ceramic capacitor placed within 5 mm of the supply pin and a bulk 10 µF tantalum or aluminum electrolytic capacitor at the board entry point. The MCU draws roughly 2-5 mA active at 4 MHz/5 V and can drop below 1 µA in sleep mode, so a low-Iq LDO such as MCP1700 is recommended for battery-powered designs.
OTP (One-Time Programmable) memory cannot be erased or rewritten - once a bit cell is programmed, the firmware is permanent. This means prototype debugging must use the PIC16F716-I/SS (flash-based, same 20-SSOP pinout) or a windowed/UV-erasable PIC16C716 JW variant. Plan firmware revisions and last-minute bug fixes carefully before committing to OTP, and always run final code on PIC16F716-I/SS for sign-off before switching to the OTP PIC16C716-04I/SS for production.
For the 20-SSOP (5.30 mm body, 0.65 mm pitch) footprint, follow IPC-7351 land-pattern guidelines: pad length 0.95 mm, pad width 0.40 mm, with 0.30 mm solder mask expansion. The exposed die-pad underneath is not present on this SSOP variant, so thermal dissipation is through the 20 leads only - keep continuous ground plane on the top layer connected to VSS pin 19 to spread heat. Place the decoupling capacitor on VDD within 5 mm and route the analog AVdd/AVss traces away from switching signals to avoid ADC noise pickup.
규정 준수 정보
RoHS, REACH, and conflict-mineral status not stated in the verified web snippets; the -I suffix denotes industrial temperature grade (-40°C to +85°C). Lead-free finish is standard on Microchip SSOP-packaged parts per Microchip packaging policy.
