PIC16CE623T-04I/SS - 4MHz 8-Bit OTP MCU 896B | Microchip
부품 번호: PIC16CE623T-04I/SS ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $3.1 | $3.10 |
| 10 | $2.78 | $27.80 |
| 100 | $2.42 | $242.00 |
| 500 | $2.15 | $1,075.00 |
| 1,000 | $1.85 | $1,850.00 |
PIC16CE623T-04I/SS 개요
A PIC16C-series microcontroller is a member of Microchip's classic 8-bit RISC family, sitting in the hierarchy: microcontroller -> 8-bit MCU -> embedded controller -> semiconductor. PIC16C devices use a Harvard architecture with separate program and data buses, enabling simultaneous instruction fetch and data access, and they are programmed via the EPROM/OTP process using Microchip's PM3 or earlier development tools. The "CE" suffix specifically indicates the EEPROM-data variant that pairs 1k-class OTP program memory with byte-erasable EEPROM for non-volatile parameter storage.
Key features that differentiate the PIC16CE623T-04I/SS include its 4MHz maximum clock, very small footprint (20-pin SSOP at 5.30mm body width), low power CMOS design with <2 mA typical operating current at 5V/4MHz, and the addition of an internal EEPROM data array not present on plain PIC16C62X OTP parts. The "-04I" suffix denotes 4MHz oscillator rating and industrial temperature range, while "/SS" identifies the SSOP package. The "T" suffix in the part number indicates Tape and Reel packaging for high-volume assembly.
Architecturally, the device uses a RISC core with 7 special-function hardware registers, an 8-level deep hardware stack, and direct/indirect addressing modes. The on-chip EEPROM (128 bytes) is accessible through dedicated read/write routines and supports >1M erase/write cycles endurance, with data retention rated >40 years per Microchip's device family specification.
Typical applications include low-cost appliance controllers, simple sensor signal conditioning front-ends, automotive interior subsystems (non-safety), battery-powered remote controls, consumer white goods user interfaces, and industrial timer/counter modules. The combination of OTP program memory, internal EEPROM data, and small SSOP footprint makes it well suited to high-volume cost-sensitive designs where field firmware updates are not required.
When designing with this device, observe that OTP program memory cannot be re-programmed in-circuit; firmware must be fully validated before programming. Always provide adequate decoupling (100 nF + 10 uF) on VDD/VDD2 and place the MCLR pull-up within 25 mm of the pin. The WDT should be enabled in any application where firmware lockup could cause unsafe behavior.
This page synthesizes distributor pricing, drop-in alternatives within the PIC16CE62X family, and practical design notes not found in the standalone manufacturer datasheet, providing a one-stop reference for engineers and procurement teams.
드롭인 대체품: PIC16CE623T-04I/SS — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC16CE623T-04I/SS (동일 폼 팩터 및 풋프린트) — 차이점: Package, Program Memory Size, Core Architecture, Timers, Program Memory Type.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC16CE623-04I/SS
✅ 드롭인✓ 재고 있음
$1.45 / 개
데이터시트 보기 →PIC16CE623-04I/SO
✅ 드롭인✓ 재고 있음
$1.31 / 개
데이터시트 보기 →PIC16CE623-20I/SS
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC16CE624-04I/SS
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$1.49 / 개
데이터시트 보기 →PIC16CE625-04I/SS
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$2.65 / 개
데이터시트 보기 →PIC16CE623T-04I/SS 최대 정격 & 전기적 특성
| Core Architecture | 8-bit PIC Harvard RISC |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 896 bytes (512 x 14 words) |
| Data SRAM | 96 bytes |
| EEPROM Data Memory | 128 bytes |
| 최대 클록 주파수 | 4 MHz |
| Instruction Cycle Time | 200 ns (4 MHz), 133 ns instruction execution |
| Instruction Set Size | 35 single-word instructions |
| Supply Voltage (VDD) | 3.0 V to 5.5 V |
| I/O Pins | 13 |
| 동작 온도 | -40C to +85C (Industrial) |
| 패키지 | 20-SSOP (5.30 mm body width) |
| 실장 유형 | Surface Mount |
| Brown-out Detect | Yes |
| Power-On Reset | Yes |
| Watchdog Timer | Yes (with on-chip RC oscillator) |
| Hardware Stack | 8 levels |
| MSL 레벨 | 1 (unlimited floor life at <30C/85% RH) |
| RoHS 상태 | Compliant |
PIC16CE623T-04I/SS 핀 구성
| 핀 1 | RA2/AN2 — Bidirectional I/O / Analog channel 2 |
| 핀 2 | RA3/AN3 — Bidirectional I/O / Analog channel 3 |
| 핀 3 | RA4/T0CKI — Bidirectional I/O / Timer0 clock input (open-drain) |
| 핀 4 | MCLR — Master Clear reset input (active low) |
| 핀 5 | VSS — Ground reference |
| 핀 6 | RB0/INT — Bidirectional I/O / External interrupt |
| 핀 7 | RB1 — Bidirectional I/O |
| 핀 8 | RB2 — Bidirectional I/O |
| 핀 9 | RB3 — Bidirectional I/O |
| 핀 10 | RB4 — Bidirectional I/O with interrupt-on-change |
| 핀 11 | RB5 — Bidirectional I/O with interrupt-on-change |
| 핀 12 | RB6 — Bidirectional I/O with interrupt-on-change |
| 핀 13 | RB7 — Bidirectional I/O with interrupt-on-change |
| 핀 14 | VDD — Positive supply voltage (3.0V to 5.5V) |
| 핀 15 | OSC2/CLKOUT — Oscillator crystal output / clock-out |
| 핀 16 | OSC1/CLKIN — Oscillator crystal input / external clock input |
| 핀 17 | RA0/AN0 — Bidirectional I/O / Analog channel 0 |
| 핀 18 | RA1/AN1 — Bidirectional I/O / Analog channel 1 |
| 핀 19 | RA5/SS/AN4 — Bidirectional I/O / SPI slave select / Analog channel 4 |
| 핀 20 | RA7 — Bidirectional I/O |
일반적인 애플리케이션
PIC16CE623T-04I/SS 적합 용도: 6 애플리케이션s: Low-Cost Appliance Controllers, Remote Control Transmitters, Industrial Timer and Counter Modules, Sensor Signal Conditioning Front-Ends, Automotive Interior Subsystems, Consumer White Goods User Interfaces.
Low-Cost Appliance Controllers
The PIC16CE623T-04I/SS fits appliance controllers (washing machines, microwave ovens, dishwashers) where the OTP memory holds fixed firmware and the 128-byte EEPROM stores user-selectable cycle parameters and end-of-cycle counters. Its 13 I/O pins directly drive relay coils, triac gate circuits, and 7-segment LED multiplex displays without external logic. The 4MHz clock and 35-instruction RISC core complete state-machine tasks in under 200 ns, well below typical AC line-cycle timing budgets. Industrial temperature rating (-40C to +85C) handles kitchen and laundry-room thermal stress, and the SSOP-20 footprint drops onto compact mainboards.
추천
Remote Control Transmitters
Battery-powered IR/RF remote controls benefit from the PIC16CE623T-04I/SS's CMOS low-power design and small SSOP-20 footprint, which minimize PCB area inside handheld enclosures. The 13 I/O pins drive a 4x4 keypad matrix with interrupt-on-change wake-up on PORTB, and the 128-byte EEPROM retains learned-device codes across battery swaps. Brown-out Detect prevents corrupted EEPROM writes when the battery approaches end-of-life, and the 4MHz internal-execution capability easily generates 38 kHz IR carrier modulation with a single timer and PWM channel. Industrial temperature rating ensures reliable operation in cold garages and hot dashboards.
추천
Industrial Timer and Counter Modules
Factory-floor timer/counter modules use the PIC16CE623T-04I/SS to sequence conveyor operations, count encoder pulses, and drive indicator LEDs. The TMR0 8-bit timer/counter with external clock input accepts quadrature encoder signals up to 4 MHz, and the WDT prevents lockup during EMI transients common in motor-drive cabinets. The on-chip BOD holds the MCU in reset during the inductive-kick brownouts that occur when nearby contactors open. The 13 I/O pins connect to optocoupler-isolated 24V inputs and outputs, and the SSOP-20 surface-mount package withstands the vibration profiles of panel-mounted equipment.
추천
Sensor Signal Conditioning Front-Ends
Sensor interface boards (thermistor bridges, RTD conditioners, simple pressure transducers) use the PIC16CE623T-04I/SS to digitize analog signals, apply linearization coefficients stored in the 128-byte EEPROM, and output calibrated serial data. The 13 I/O pins share duty between the analog-front-end control lines and a UART/I2C/SPI master interface to a host controller. Although the PIC16CE623 has no on-chip ADC, its low cost and small footprint make it ideal as a companion controller to an external ADC. EEPROM storage of per-sensor calibration data eliminates manual trimming during manufacture.
추천
Automotive Interior Subsystems
Non-safety automotive interior subsystems (mirror controllers, ambient lighting, seat-position memory, keyless-entry fob receivers) use the PIC16CE623T-04I/SS for its compact SSOP-20 footprint and industrial temperature range. The 13 I/O pins drive LED current sinks and read Hall-effect position sensors, while the 128-byte EEPROM stores last-used mirror/ seat positions. The 4MHz clock and BOD ensure clean operation through the cranking-voltage dips and load-dump transients typical of 12V automotive buses. Although not AEC-Q100 qualified, the industrial-grade part is widely used in non-safety aftermarket accessories.
추천
Consumer White Goods User Interfaces
User-interface panels for refrigerators, air-conditioner indoor units, and washing machines integrate the PIC16CE623T-04I/SS to scan capacitive touch keys, drive LCD segments, and communicate with the main appliance MCU via UART. The 13 I/O pins handle up to a 4x5 matrix keypad plus a small direct-drive LCD, while the 128-byte EEPROM stores user preferences (temperature setpoints, mode presets) across power cycles. The 4MHz oscillator budget is sufficient for software-UART baud rates up to 9600 bps with interrupt-driven reception. The SSOP-20's 5.30 mm body width fits slim panel designs.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC16CE623T-04I/SS — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC16CE623-04I/SS | PIC16CE623-04I/SO | PIC16CE623-20I/SS | PIC16CE624-04I/SS | PIC16CE625-04I/SS |
|---|---|---|---|---|---|---|
| Package | 20-SSOP (5.30 mm) | 20-SSOP (5.30 mm) - same | 20-SOIC - same pin count | 20-SSOP (5.30 mm) - same | 20-SSOP (5.30 mm) - same | 20-SSOP (5.30 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory | 896 B OTP (512 x 14) | 896 B OTP - same | 896 B OTP - same | 896 B OTP - same | 1.75 kB OTP | 3.5 kB OTP |
| Data SRAM | 96 B | 96 B - same | 96 B - same | 96 B - same | 96 B - same | 96 B - same |
| EEPROM Data Memory | 128 B | 128 B - same | 128 B - same | 128 B - same | 128 B - same | 128 B - same |
| Maximum Clock | 4 MHz | 4 MHz - same | 4 MHz - same | 20 MHz | 4 MHz - same | 4 MHz - same |
| Supply Voltage | 3.0 V to 5.5 V | 3.0 V to 5.5 V - same | 3.0 V to 5.5 V - same | 3.0 V to 5.5 V - same | 3.0 V to 5.5 V - same | 3.0 V to 5.5 V - same |
| I/O Pins | 13 | 13 - same | 13 - same | 13 - same | 13 - same | 13 - same |
| Operating Temperature | -40C to +85C | -40C to +85C - same | -40C to +85C - same | -40C to +85C - same | -40C to +85C - same | -40C to +85C - same |
| Lifecycle Status | Active | Active | Active | Active | Active | Active |
주요 차별점
- Tape-and-Reel packaging for high-volume SMT (vs PIC16CE623-04I/SS (tube))
- Industrial temperature range (-40C to +85C) (vs PIC16CE623T-04E/SS (extended commercial))
- On-chip 128-byte EEPROM data memory (vs Plain PIC16C623 (no EEPROM))
- 4 MHz headroom matches industrial cost targets (vs PIC16CE623-20I/SS (20 MHz))
설계 노트
Place a 100 nF ceramic decoupling capacitor within 5 mm of the VDD pin (pin 14) and a bulk 10 uF tantalum or aluminum polymer capacitor on the same VDD node, sized to ride through 50 ms of VDD droop. The PIC16CE623T-04I/SS draws <2 mA active at 4 MHz/5V but Brown-out Detect resets during VDD dips below ~4.0V; a sufficient bulk capacitor prevents nuisance BOD events during motor inrush on shared supplies.
Route the MCLR pull-up resistor (typically 10 kOhm to VDD) within 25 mm of pin 4. If using ICSP programming header, place a series resistor or diode-isolated path per Microchip's programming specification to prevent the on-board pull-up from interfering with the programmer's Vpp high-voltage (~13V) signal. Keep the crystal or resonator within 10 mm of pins 15-16 to minimize stray capacitance and EMI pickup on the OSC lines.
OTP program memory cannot be re-programmed in-circuit. Always validate firmware with a Flash-equivalent part (PIC16F627/628) before committing to OTP production. EEPROM writes must follow the EECON2 unlock sequence (write 0x55 then 0xAA to EECON2); omitting this sequence silently fails and may indicate the write was incomplete. Also note that the PIC16CE623 lacks an on-chip ADC despite the ANx pin names - analog functions are reserved for future variants and these pins are digital-only on this part.
PORTB pins RB4-RB7 feature interrupt-on-change wakeup; ensure mechanical switches connected to these pins have 100 ns hardware debouncing because the IOC latches are very sensitive. For long PCB traces to external connectors, add 100 Ohm series resistors near the MCU to dampen transmission-line ringing. The RA4 pin is open-drain and requires an external pull-up if used as an output.
규정 준수 정보
RoHS and REACH compliance per Microchip product page. Not AEC-Q100 qualified - the I-suffix indicates industrial temperature grade (-40C to +85C), not automotive qualification. For AEC-Q100 qualified PIC16 parts, see PIC16F family with -E or -Q part number suffixes.
