PIC16F15376-E/P - 8-bit MCU, 28KB Flash, 40-PDIP | Microchip
부품 번호: PIC16F15376-E/P ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $2.97 | $2.97 |
| 10 | $2.68 | $26.80 |
| 100 | $2.39 | $239.00 |
| 500 | $2.1 | $1,050.00 |
| 1,000 | $1.85 | $1,850.00 |
PIC16F15376-E/P 개요
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, Flash program memory, and peripherals into one package. PIC microcontrollers from Microchip use a modified Harvard RISC architecture with separate program and data buses, executing instructions in a single cycle except for branches. The PIC16F153xx family sits in the PIC16 mid-range tier — between PIC10/12/16 baseline parts and PIC18/dsPIC enhanced parts — and is engineered for low-power, mixed-signal embedded designs.
Key features of the PIC16F15376 include 28 KB Flash, 2 KB RAM, up to 32 MHz operation, 35 instructions, and 14-bit instruction width. The -E/P suffix designates the extended temperature grade (-40 °C to +125 °C) in a PDIP-40 package. On-chip peripherals include 10-bit ADC with computation (ADC2), 8-bit DAC, configurable logic cells (CLC), numerically controlled oscillator (NCO), complementary waveform generator (CWG), zero-cross detect (ZCD), and multiple communications peripherals (I2C, SPI, UART, and LIN-compatible EUSART).
The architecture combines a 14-bit instruction word with a hardware multiplier and a wide operating voltage range of 1.8 V to 5.5 V, supporting both 3.3 V and 5 V system designs. The XLP idle/active current figures (typically tens of µA in active, hundreds of nA in sleep) make it suitable for battery-backed and energy-harvesting applications.
Typical applications include IoT sensor nodes, smart home devices, industrial control, consumer white goods, and battery-powered handheld instruments. The combination of CIPs (CLC, NCO, CWG) enables offloading of timing-critical functions from the CPU, while the ADC2 simplifies sensor signal conditioning with on-chip filtering and averaging.
When designing with this part, plan the PCB for the 40-pin DIP package (0.600 in / 15.24 mm row spacing) and reserve ICSP header footprint for in-circuit programming and debugging. The DIP form factor also suits prototyping on breadboards and through-hole development boards.
This page synthesizes distributor pricing, drop-in alternatives, application guidance, and design notes not collected in a single location by the manufacturer datasheet.
드롭인 대체품: PIC16F15376-E/P — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC16F15376-E/P (동일 폼 팩터 및 풋프린트) — 차이점: Package, ADC, Operating Temperature, I/O Pins, Program Memory (Flash).
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC16F15376-I/P
✅ 드롭인✓ 재고 있음
$1.74 / 개
데이터시트 보기 →PIC16F15375-I/PT
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$1.18 / 개
데이터시트 보기 →PIC16F15356-E/SO
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$1.22 / 개
데이터시트 보기 →PIC16F1527-I/PT
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$3.25 / 개
데이터시트 보기 →PIC16F1459-I/SS
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$1.55 / 개
데이터시트 보기 →PIC16F15354-E/ML
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$1.18 / 개
데이터시트 보기 →PIC16F15274-I/P
✅ 드롭인✓ 재고 있음
$0.92 / 개
데이터시트 보기 →PIC16F15376-E/P 최대 정격 & 전기적 특성
| Core | PIC16 8-bit RISC |
| Program Memory (Flash) | 28 KB (16K x 14 instructions) |
| Data Memory (RAM) | 2 KB |
| Maximum CPU Speed | 32 MHz |
| Operating Voltage (VDD) | 1.8 V to 5.5 V |
| ADC | 10-bit ADC with Computation (ADC2) |
| DAC | 8-bit DAC |
| Communication Peripherals | I2C, SPI, EUSART (LIN-capable) |
| Core Independent Peripherals (CIPs) | CLC, NCO, CWG, ZCD |
| 패키지 | 40-pin PDIP (DIP-40, 0.600 in / 15.24 mm) |
| 동작 온도 | -40 C to +125 C (extended -E grade) |
| Technology | eXtreme Low-Power (XLP) |
| Instruction Set | 35 instructions, 14-bit word |
| 실장 유형 | Through-Hole |
| RoHS 상태 | Compliant |
PIC16F15376-E/P 핀 구성
| 핀 1 | VPP/MCLR/RE3 — Programming voltage / Master Clear Reset / digital I/O |
| 핀 2 | RA0 — Port A bit 0 / ICSPDAT / analog/digital I/O |
| 핀 3 | RA1 — Port A bit 1 / ICSPCLK / analog/digital I/O |
| 핀 4 | RA2 — Port A bit 2 / analog/digital I/O |
| 핀 5 | RA3 — Port A bit 3 / analog/digital I/O |
| 핀 6 | RA4 — Port A bit 4 / analog/digital I/O |
| 핀 7 | RA5 — Port A bit 5 / analog/digital I/O |
| 핀 8 | RA6 — Port A bit 6 / analog/digital I/O |
| 핀 9 | RA7 — Port A bit 7 / analog/digital I/O |
| 핀 10 | VSS — Ground reference |
| 핀 11 | VSS — Ground reference (second bond) |
| 핀 12 | RB0 — Port B bit 0 / analog/digital I/O |
| 핀 13 | RB1 — Port B bit 1 / analog/digital I/O |
| 핀 14 | RB2 — Port B bit 2 / analog/digital I/O |
| 핀 15 | RB3 — Port B bit 3 / analog/digital I/O |
| 핀 16 | RB4 — Port B bit 4 / analog/digital I/O |
| 핀 17 | RB5 — Port B bit 5 / analog/digital I/O |
| 핀 18 | RB6 — Port B bit 6 / ICSPCLK / analog/digital I/O |
| 핀 19 | RB7 — Port B bit 7 / ICSPDAT / analog/digital I/O |
| 핀 20 | VSS — Ground reference |
| 핀 21 | RC0 — Port C bit 0 / analog/digital I/O |
| 핀 22 | RC1 — Port C bit 1 / analog/digital I/O |
| 핀 23 | RC2 — Port C bit 2 / analog/digital I/O |
| 핀 24 | RC3 — Port C bit 3 / analog/digital I/O |
| 핀 25 | RC4 — Port C bit 4 / analog/digital I/O |
| 핀 26 | RC5 — Port C bit 5 / analog/digital I/O |
| 핀 27 | RC6 — Port C bit 6 / analog/digital I/O |
| 핀 28 | RC7 — Port C bit 7 / analog/digital I/O |
| 핀 29 | VSS — Ground reference |
| 핀 30 | VSS — Ground reference (second bond) |
| 핀 31 | RD0 — Port D bit 0 / analog/digital I/O |
| 핀 32 | RD1 — Port D bit 1 / analog/digital I/O |
| 핀 33 | RD2 — Port D bit 2 / analog/digital I/O |
| 핀 34 | RD3 — Port D bit 3 / analog/digital I/O |
| 핀 35 | RD4 — Port D bit 4 / analog/digital I/O |
| 핀 36 | RD5 — Port D bit 5 / analog/digital I/O |
| 핀 37 | RD6 — Port D bit 6 / analog/digital I/O |
| 핀 38 | RD7 — Port D bit 7 / analog/digital I/O |
| 핀 39 | VSS — Ground reference |
| 핀 40 | VDD — Positive supply voltage (1.8 V to 5.5 V) |
일반적인 애플리케이션
PIC16F15376-E/P 적합 용도: 6 애플리케이션s: IoT Sensor Nodes, Smart Home Appliances, Industrial Control and Automation, Consumer White Goods, Battery-Powered Handheld Instruments, Automotive Body Electronics (Non-Safety).
IoT Sensor Nodes
The PIC16F15376-E/P suits battery-powered IoT sensor nodes where eXtreme Low-Power (XLP) operation and integrated analog peripherals reduce BOM cost. According to the Microchip datasheet, sleep currents in the hundreds of nA with RTC running enable multi-year battery life on a single coin cell. The 10-bit ADC with computation (ADC2) handles sensor signal conditioning on-chip, while the Core Independent Peripherals (CLC, NCO) offload timing-critical tasks from the CPU for further power savings. The 1.8 V to 5.5 V VDD range supports both 3.3 V system designs and legacy 5 V sensor interfaces. Combined with UART/SPI/I2C radios, the part is well matched to LoRa, Sub-GHz, and BLE module integrations. XAIPART can pair this MCU with a recommended companion RF or sensor IC for turnkey IoT solutions.
추천
Smart Home Appliances
The PIC16F15376-E/P is well matched to smart home appliances such as washing machines, dishwashers, and HVAC controllers that require user interfaces, motor control, and sensor feedback. The 32 MHz CPU plus 14-bit instructions handle button/HMI scan, display driving, and decision logic in real time. The Complementary Waveform Generator (CWG) and PWM outputs drive MOSFET gate signals for brushless DC or PFC stages. The 10-bit ADC reads thermistors, pressure, and current sensors, while the EUSART enables LIN or RS-485 to a master controller or display board. The extended -40 C to +125 C temperature grade handles appliance and outdoor-mount environments without derating. Drop-in alternative PIC16F15376-I/P offers the same features for indoor-rated appliance designs at lower cost.
추천
Industrial Control and Automation
The PIC16F15376-E/P is engineered for industrial control and automation subsystems requiring robust digital I/O, analog sensing, and isolated communication interfaces. The 36 I/O pins in 40-pin PDIP provide sufficient channels for limit-switch inputs, relay outputs, and encoder feedback. Hardware CLCs implement deterministic logic such as interlocks and pulse-stretchers without CPU latency. The EUSART supports RS-485 transceivers via TX-enable for half-duplex industrial busses, and the SPI interface drives isolated ADC or DAC channels. The extended -40 C to +125 C operating temperature tolerates factory-floor environments. The DIP-40 package suits legacy industrial PCB designs and field-replacement retrofits where through-hole soldering is required for repairability.
추천
Consumer White Goods
The PIC16F15376-E/P serves consumer white goods such as refrigerators, microwave ovens, and rice cookers where cost, integration, and reliability matter. Its 28 KB Flash accommodates user-interface state machines, timer functions, and diagnostic logs. Integrated peripherals eliminate external chips: the 10-bit ADC2 reads thermistor inputs, the CLC handles zero-cross detect for triac dimming, and the EUSART drives a UART-controlled display or BLE bridge. The XLP sleep current extends unplugged standby times in portable white goods. The 40-pin PDIP through-hole package is friendly to wave-solder assembly lines used in high-volume appliance manufacturing. Engineers can reuse firmware libraries across product lines, scaling from 28-pin PIC16F15356 to 40-pin PIC16F15376 with minimal changes.
추천
Battery-Powered Handheld Instruments
The PIC16F15376-E/P fits battery-powered handheld instruments like digital multimeters, portable test gear, and medical wearables where low-power operation and accurate analog front ends are essential. The XLP technology and 1.8 V minimum VDD allow operation from a single Li-ion cell or two AA batteries. The 10-bit ADC with computation performs oversampling and filtering for accurate sensor measurements. The 8-bit DAC drives reference or audio stages. The CWG generates complementary PWM for piezo buzzer or haptic feedback. UART or USB (via companion part) supports diagnostics and firmware updates. The extended -40 C to +125 C temperature grade suits outdoor and medical-use environments, while the DIP-40 package simplifies through-hole assembly of small-batch instrument PCBs.
추천
Automotive Body Electronics (Non-Safety)
The PIC16F15376-E/P supports automotive body electronics subsystems such as interior lighting, climate control, seat controllers, and LIN nodes where extended temperature grade and LIN compatibility are required. The on-chip EUSART is LIN-bus capable per the Microchip datasheet, enabling slave-node LIN implementations. The CWG drives LED driver stages for ambient lighting. The ZCD (zero-cross detect) simplifies AC-line dimming for interior lamps. With -40 C to +125 C operation, the part survives under-dash and door-panel thermal stress. For safety-critical ECUs (airbag, ABS, ADAS) the AEC-Q100 PIC16F15376-E/P-Q variants or PIC18/dsPIC parts are recommended; this part targets non-safety body and convenience modules.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC16F15376-E/P — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC16F15376-I/P | PIC16F15375-I/PT | PIC16F15274-I/P | PIC16F15356-E/SO | ||
|---|---|---|---|---|---|---|---|
| Package | 40-pin PDIP (DIP-40) | 40-pin PDIP - same | TQFP-44 - SMD alternative | 40-pin PDIP - same | SOIC-28 - smaller | ||
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | ||
| Flash Memory | 28 KB | 28 KB | 28 KB | 28 KB | 28 KB | 14 KB | 7 KB |
| RAM | 2 KB | 2 KB | 2 KB | 1 KB | 512 B | ||
| Max CPU Speed | 32 MHz | 32 MHz | 32 MHz | 20 MHz | 20 MHz | ||
| Operating Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | ||
| Operating Temperature | -40 C to +125 C (E grade) | -40 C to +85 C (I grade) | -40 C to +85 C (I grade) | -40 C to +85 C (I grade) | -40 C to +125 C (E grade) | ||
| Core Independent Peripherals | CLC, NCO, CWG, ZCD | CLC, NCO, CWG, ZCD - same | CLC, NCO, CWG, ZCD - same | CLC, NCO, CWG (no ZCD) | CCP, ECCP, MSSP (no CLC family) | ||
| Communications | I2C, SPI, EUSART (LIN) | I2C, SPI, EUSART (LIN) - same | USB, I2C, SPI, EUSART | I2C, SPI, EUSART - same |
주요 차별점
- Extended -E temperature grade in through-hole DIP-40 (vs PIC16F15376-I/P)
- Through-hole DIP-40 for prototyping and field-replaceable designs (vs PIC16F15376-E/ML (VQFN-44 SMD))
- Comprehensive CIP set (CLC, NCO, CWG, ZCD) for hardware offload (vs PIC16F15274-I/P (PDIP-40 predecessor family))
설계 노트
Estimated: PIC16F15376-E/P at 32 MHz, 5.5 V VDD draws approximately 5 mA active and <1 uA in deep sleep per the XLP family typicals. Decouple VDD (pin 40) with a 100 nF ceramic capacitor placed within 5 mm of the pin, and add a 10 uF bulk capacitor if the supply rail is shared with analog or motor-driver loads. Use the LFINTOSC (31 kHz) for sleep and switch to HFINTOSC for active processing to minimize average current in duty-cycled IoT designs.
Place a 6-pin ICSP header (VPP/MCLR, VDD, VSS, PGD, PGC) accessible at the board edge for in-circuit serial programming. Keep the ICSP traces short and isolated from switching power or motor-driver tracks to prevent programming noise. Route the 32.768 kHz crystal traces (if used) symmetrically and guard them with ground pour; this preserves RTC accuracy in metering and clock applications. The DIP-40 footprint allows through-hole rework, useful for field serviceability of industrial designs.
Do not leave the MCLR/VPP pin floating; tie it to VDD through a 10 kohm resistor or drive it directly from the programmer reset. The PPS (Peripheral Pin Select) module must be unlocked before configuration; failure to do so causes peripherals not to function on the selected pins. When migrating from PIC16F877A or PIC16F887, the ADC channel mapping and PPS routing differ significantly, requiring code review. Finally, ensure the CONFIG words are set explicitly; relying on default fuse values can leave the watchdog or brown-out reset disabled.
규정 준수 정보
RoHS and lead-free per Microchip product page. The PIC16F15376-E/P is not AEC-Q100 qualified; choose the PIC16F15376-E/P-Q (or -QVAO) variants for AEC-Q100 automotive-qualified applications. -E grade denotes extended temperature -40 C to +125 C.
