PIC16LF15376-I/MV - 28KB Flash 8-bit MCU | Microchip
부품 번호: PIC16LF15376-I/MV ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $2.85 | $2.85 |
| 10 | $2.55 | $25.50 |
| 100 | $2.2 | $220.00 |
| 500 | $1.95 | $975.00 |
| 1,000 | $1.72 | $1,720.00 |
PIC16LF15376-I/MV 개요
An 8-bit PIC microcontroller (MCU) is a compact, low-cost processor built on Microchip's RISC-based PIC architecture. It executes one instruction per cycle and is widely used in embedded applications where predictable behavior, low power, and integrated peripherals outweigh raw computational speed. PIC16 MCUs occupy the mid-tier of Microchip's 8-bit portfolio, balancing peripherals and code density with low cost.
Key features include 2 KB RAM, four 10-bit PWM outputs, a 10-bit ADC, a 5-bit/8-bit DAC, configurable logic cells (CLC), complementary waveform generator (CWG), and up to 36 I/O pins. Two EUSART plus SPI and I2C serial engines enable simultaneous sensor bus and host communication, while on-chip peripherals reduce external component count.
The device uses an internal 32 MHz high-speed oscillator with PLL, supports up to 32 MHz system clock, and provides selectable clock sources including 31 kHz LFINTOSC for low-power modes. XLP delivers nanoWatt sleep currents, allowing years of operation from a single coin cell in duty-cycled sensing applications.
Typical applications include IoT sensor nodes, battery-powered medical wearables, low-power wireless sensor hubs, industrial HVAC controls, and consumer appliance control panels. Designers leverage the integrated analog peripherals to digitize sensor signals without external ADC ICs.
When designing, reserve a 100 nF decoupling capacitor near each VDD pin and a 10 uF bulk capacitor at the supply entry point. Use Microchip's MPLAB X IDE with the XC8 compiler for code development and the PICkit 4 or MPLAB Snap debugger for in-circuit programming and debugging.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, helping procurement and engineering teams make faster sourcing and design decisions.
드롭인 대체품: PIC16LF15376-I/MV — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC16LF15376-I/MV (동일 폼 팩터 및 풋프린트) — 차이점: DAC, Package, ADC, I/O Pins, Program Memory (Flash).
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청PIC16LF15376-I/MV 최대 정격 & 전기적 특성
| Core Architecture | PIC16 (8-bit RISC) |
| Family | PIC16F15376 (XLP) |
| CPU Speed | 32 MHz (max) |
| Program Memory (Flash) | 28 KB (16K x 14) |
| Data RAM | 2 KB |
| Operating Voltage Range | 1.8 V to 3.6 V |
| 패키지 | 40-pin UQFN (5x5 mm) with exposed pad |
| I/O Pins | Up to 36 |
| ADC | 10-bit, multi-channel |
| DAC | 5-bit and 8-bit |
| PWM Channels | 4 x 10-bit |
| Comparators | Yes |
| CLC (Configurable Logic Cells) | 4 |
| CWG (Complementary Waveform Generator) | Yes |
| EUSART | 2 |
| SPI | Yes |
| I2C | Yes |
| Internal Oscillator | 32 MHz with PLL, 31 kHz LFINTOSC |
| XLP (eXtreme Low Power) | Yes |
| 동작 온도 | -40 C to +85 C (Industrial) |
| RoHS 상태 | Compliant |
PIC16LF15376-I/MV 40-pin uqfn (5x5 mm) with exposed pad 핀 구성 가이드
PIC16LF15376-I/MV(40-pin uqfn (5x5 mm) with exposed pad 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: PIC16LF15376-I/MV.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
PIC16LF15376-I/MV 적합 용도: 6 애플리케이션s: Battery-Powered IoT Sensor Nodes, Wearable Health Monitoring Devices, Industrial HVAC Control Panels, Consumer Appliance Control Boards, Remote Wireless Sensor Hubs, Educational and Maker Platforms.
Battery-Powered IoT Sensor Nodes
The PIC16LF15376-I/MV suits IoT sensor nodes because its 1.8-3.6 V supply range accepts single-cell LiCoin or 2x AA alkaline chemistries directly without boost regulators. XLP nanoWatt technology holds sleep current under 1 uA while a 31 kHz LFINTOSC maintains a real-time wake source. Integrated 10-bit ADC, four CLCs, and 2 KB RAM sample thermistor, PIR, or photodiode signals and run small protocol stacks without external logic.
추천
Wearable Health Monitoring Devices
For wearable health devices, the PIC16LF15376-I/MV combines low active current with 32 MHz compute headroom to drive on-body sensors like heart-rate, SpO2, and motion trackers. The 5-bit/8-bit DAC plus 10-bit ADC digitizes biopotential signals directly, while the 40-pin UQFN (5x5 mm) keeps the PCB footprint small enough for wrist or patch enclosures. XLP sleep modes extend battery life across multi-day wear cycles.
추천
Industrial HVAC Control Panels
The PIC16LF15376-I/MV fits HVAC control panels needing multiple sensor inputs (temperature, humidity, pressure) and switched outputs (fans, valves, relays). Four 10-bit PWM channels drive fan speed or damper servos without extra timers, while the CWG provides complementary drive for three-phase BLDC motor support. Two EUSART ports bridge to a master controller display and a wired Modbus fieldbus simultaneously.
추천
Consumer Appliance Control Boards
The PIC16LF15376-I/MV integrates almost every peripheral a small appliance needs: PWMs for motor drive, ADC for temperature sensing, CLC for safety logic, and EUSART/SPI/I2C for HMI bridges. The 28 KB Flash fits the largest of UI state machines and fault diagnostics. Designers can retire external EEPROMs by leveraging the PIC16's data EEPROM, lowering the BOM cost for high-volume white-goods production.
추천
Remote Wireless Sensor Hubs
Wireless sensor hubs benefit from the PIC16LF15376-I/MV because two EUSART blocks can simultaneously host a sub-GHz radio module (LoRa, FSK) and a wired debug or RS-485 backhaul. Four CLCs implement custom packet framing and timing, while 28 KB Flash holds LoRaWAN or proprietary MAC code. XLP keeps idle current low enough that battery-powered hubs last multiple years on duty-cycled transmissions.
추천
Educational and Maker Platforms
The PIC16LF15376-I/MV is well suited to learning platforms because the free MPLAB X IDE, XC8 compiler, and MPLAB Code Configurator let students initialize peripherals graphically. The PICkit 4 or Curiosity Nano board provides low-cost programming and debugging. The chip's combination of PWMs, ADC, DAC, CLCs, and dual EUSART gives learners exposure to nearly every common MCU peripheral within a single $2 device.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC16LF15376-I/MV — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC16LF15376-E/MV | PIC16F15376-I/MV | PIC16LF15376-I/ML | PIC16LF15376-I/MVVAO |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 40-pin UQFN (5x5 mm) | 40-pin UQFN (5x5 mm) - same | 40-pin UQFN (5x5 mm) - same | 44-pin QFN (8x8 mm) - different | 40-pin UQFN (5x5 mm) - same |
| Flash Memory | 28 KB (16K x 14) | 28 KB | 28 KB | 28 KB | 28 KB |
| RAM | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| Operating Voltage | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 2.3 V to 5.5 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Temperature Grade | -40 C to +85 C (Industrial) | -40 C to +125 C (Extended) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) |
| Max CPU Speed | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| PWM Channels | 4 x 10-bit | 4 x 10-bit | 4 x 10-bit | 4 x 10-bit | 4 x 10-bit |
주요 차별점
- Lowest voltage operation in PIC16F15376 family (vs PIC16F15376-I/MV)
- Extended temperature variant available in same footprint (vs PIC16LF15376-E/MV)
- Larger QFN variant offers more I/O pins (vs PIC16LF15376-I/ML)
설계 노트
Place a 100 nF decoupling capacitor adjacent to every VDD pin and a 10 uF bulk capacitor at the supply entry to the PIC16LF15376-I/MV. The exposed thermal pad (EP) on the UQFN-40 must be soldered to a copper pour tied to ground to dissipate heat and provide a low-impedance return path. Use a ferrite bead on VDD if the board shares a noisy digital supply.
Always configure the Configuration Words (CONFIG1, CONFIG2, CONFIG3) before exiting reset, especially the watchdog timer (WDTE) and brown-out reset (BOR) settings. Forgetting to enable the PLL prevents the 32 MHz operation. For low-power designs, switch the system clock to LFINTOSC before entering Sleep to keep active current in the microamp range.
Route the ICSPDAT/ICSPCLK traces (typically RB7/RB6) away from switching power nodes to prevent programming glitches. Keep analog signals (ADC, DAC) short and away from PWM outputs to minimize coupling. The UQFN-40 EP should occupy at least 50% copper area with thermal vias for reliable operation above 32 MHz.
The PIC16LF15376-I/MV dissipates well under 100 mW even at full 32 MHz operation, so no external heatsink is required. However, exposed-pad soldering improves thermal conductivity to the PCB, keeping the junction below the 150 C maximum at industrial temperatures. Ensure the EP is soldered to a continuous ground pour, not a trace, for heat spreading.
규정 준수 정보
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified; the automotive-grade PIC16F15376-E/MVAO is the alternative. Lead-free reflow profile per JEDEC J-STD-020.
