PIC16LF1713-I/SO - 32MHz 8-bit MCU, 7KB Flash, 28-SOIC | Microchip
부품 번호: PIC16LF1713-I/SO ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $1.92 | $1.92 |
| 10 | $1.74 | $17.40 |
| 100 | $1.49 | $149.00 |
| 500 | $1.31 | $655.00 |
| 1,000 | $1.18 | $1,180.00 |
PIC16LF1713-I/SO 개요
A microcontroller (MCU) is a single-chip computer built around a CPU core, program memory (Flash/ROM), working memory (RAM), and a set of on-chip peripherals such as timers, ADC, communication controllers, and GPIO. The PIC16F family sits within Microchip's 8-bit mid-range MCU hierarchy: PIC10/12/16 -> 8-bit MCU -> microcontroller -> embedded controller -> semiconductor. The 'LF' suffix indicates the wide-voltage, low-power XLP variant optimised for battery-powered applications.
Key features include Intelligent Analog integration: up to two on-chip op-amps, up to two high-speed comparators, up to 28 channels of 10-bit ADC, and a 5/8-bit DAC. Core-Independent Peripherals such as the Configurable Logic Cell (CLC), Complementary Output Generator (COG), Numerically Controlled Oscillator (NCO) and Zero-Cross Detect (ZCD) operate without CPU intervention, enabling hardware-driven events that keep the core in sleep.
The architecture combines a RISC instruction set with Peripheral Pin Select (PPS), which lets digital peripherals and some analog inputs be remapped to a wide choice of pins. Available communications include EUSART, I2C, and SPI. Compared with bare 8-bit MCUs without analog integration, the PIC16LF1713 cuts BOM cost by replacing external op-amps and comparators with on-chip blocks.
Typical applications include low-cost sensor signal conditioning, battery-powered IoT nodes, LED lighting control with ZCD-based dimming, power-conversion support (SMPS secondary-side control), and consumer appliances where small footprint and integrated analog matter.
When designing, ensure VDD decoupling uses a 0.1 uF plus 10 uF bulk near the IC. Program the PPS carefully so analog channels remain mapped to analog-capable pins and avoid conflicts between CLC and PWM outputs.
This page synthesizes distributor pricing, drop-in PIC16F/LF17xx alternatives, and practical design notes not found in the manufacturer datasheet alone.
드롭인 대체품: PIC16LF1713-I/SO — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC16LF1713-I/SO (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Package, Core Independent Peripherals, DAC, Program Memory (Flash).
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC16F1713-I/SO
✅ 드롭인✓ 재고 있음
$1.59 / 개
데이터시트 보기 →PIC16LF1713-I/SP
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC16LF1713-E/SO
✅ 드롭인✓ 재고 있음
$0.97 / 개
데이터시트 보기 →PIC16LF1709-I/SO
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC16LF1716-I/SO
✅ 드롭인✓ 재고 있음
$1.55 / 개
데이터시트 보기 →PIC16LF1713-I/SO 최대 정격 & 전기적 특성
| Core | PIC 8-bit RISC |
| Series | PIC16F171x / PIC16LF171x (XLP) |
| Program Memory | 7 KB (4K x 14) Flash |
| RAM | 512 bytes |
| Maximum CPU Frequency | 32 MHz |
| Operating Voltage (Vdd) | 1.8 V to 3.6 V |
| I/O Pins | 25 |
| ADC | 10-bit, up to 28 channels |
| DAC | 5-bit / 8-bit, 1 channel |
| Comparators | Up to 2 high-speed |
| Op-Amps | Up to 2 on-chip |
| Core-Independent Peripherals | CLC, COG, NCO, ZCD |
| PWM / CCP | Yes (CCP, PWM) |
| Communication | EUSART, I2C, SPI |
| Peripheral Pin Select (PPS) | Yes |
| 패키지 | 28-SOIC (0.295", 7.50 mm width) |
| 실장 유형 | Surface Mount |
| 동작 온도 | -40 C to +85 C (Industrial, '-I') |
| RoHS 상태 | Compliant |
PIC16LF1713-I/SO 핀 구성
| 핀 1 | RA7/OSC1/CLKIN — General-purpose I/O / crystal oscillator input / external clock input |
| 핀 2 | RA6/OSC2/CLKOUT — General-purpose I/O / crystal oscillator output / clock output |
| 핀 3 | RA5 — General-purpose I/O |
| 핀 4 | RA4 — General-purpose I/O |
| 핀 5 | RA3/MCLR/VPP — General-purpose I/O / Master Clear (reset, active-low) / programming voltage input |
| 핀 6 | RC0 — General-purpose I/O |
| 핀 7 | RC1 — General-purpose I/O |
| 핀 8 | RC2 — General-purpose I/O |
| 핀 9 | RC3 — General-purpose I/O |
| 핀 10 | RC4 — General-purpose I/O |
| 핀 11 | RC5 — General-purpose I/O |
| 핀 12 | RC6 — General-purpose I/O |
| 핀 13 | RC7 — General-purpose I/O |
| 핀 14 | VSS — Ground reference |
| 핀 15 | RB7/PGD — General-purpose I/O / ICSP data line |
| 핀 16 | RB6/PGC — General-purpose I/O / ICSP clock line |
| 핀 17 | RB5 — General-purpose I/O |
| 핀 18 | RB4 — General-purpose I/O |
| 핀 19 | RB3 — General-purpose I/O |
| 핀 20 | RB2 — General-purpose I/O |
| 핀 21 | RB1 — General-purpose I/O |
| 핀 22 | RB0 — General-purpose I/O |
| 핀 23 | VDD — Positive supply voltage (1.8V-3.6V) |
| 핀 24 | RA2 — General-purpose I/O / analog input |
| 핀 25 | RA1 — General-purpose I/O / analog input |
| 핀 26 | RA0 — General-purpose I/O / analog input |
| 핀 27 | VSS — Ground reference (secondary) |
| 핀 28 | VDD — Positive supply voltage (secondary) |
일반적인 애플리케이션
PIC16LF1713-I/SO 적합 용도: 6 애플리케이션s: Battery-Powered IoT Sensor Node, AC Line Voltage Zero-Cross Detection, SMPS Secondary-Side Control, LED Lighting Driver Control, Industrial Sensor Signal Conditioning, Consumer Appliance Control Board.
Battery-Powered IoT Sensor Node
The PIC16LF1713-I/SO fits battery-powered IoT nodes because its 1.8V-3.6V Vdd range accepts a single Li-ion or 2xAA cell directly without a boost regulator. Its nanoWatt XLP sleep currents keep idle draw in the microampere range, while the on-chip 10-bit ADC plus two op-amps condition sensor signals without external active components. CLC and NCO run autonomously while the core sleeps, enabling years of battery life for remote temperature, humidity, and occupancy sensors. Placed between a coin cell and a low-power RF module (e.g. Sub-GHz or BLE), it acts as the supervisory MCU and analog front end, replacing a discrete op-amp-plus-MCU two-chip design.
추천
AC Line Voltage Zero-Cross Detection
The PIC16LF1713-I/SO's integrated Zero-Cross Detect (ZCD) peripheral directly senses the AC mains zero-crossing event through a single series resistor, eliminating the need for an external zero-cross optocoupler or signal-conditioning circuit. Combined with the on-chip Complementary Output Generator (COG) and PWM, the MCU can drive a TRIAC or IGBT-based solid-state relay at precise phase angles for dimmer and motor-control applications. The MCU core remains in sleep while ZCD triggers the COG, dramatically reducing dissipation. This topology replaces an analog zero-cross IC plus an MCU with one part, reducing BOM cost by roughly 30-40%.
추천
SMPS Secondary-Side Control
The PIC16LF1713-I/SO suits secondary-side regulation in isolated AC-DC and DC-DC converters. The high-speed comparator enables peak-current-mode control loops, the 10-bit ADC monitors Vout and current, and the PWM/CCP block drives the synchronous-rectifier MOSFET via an opto-isolated feedback path. The NCO produces precise digital frequency synthesis for spread-spectrum control schemes that reduce EMI. With 7 KB Flash and 512B RAM it can run modern digital-compensation algorithms including Type-III PID. The 28-SOIC footprint keeps the secondary-side PCB compact, and the 1.8V minimum Vdd suits 3.3V auxiliary rails.
추천
LED Lighting Driver Control
The PIC16LF1713-I/SO can drive constant-current LED strings using its 10-bit ADC to measure load current and PWM/CCP to set the dimming duty cycle. The COG peripheral produces complementary gate-drive signals for half-bridge LED driver topologies, while ZCD synchronises dimming to the AC line for flicker-free phase-angle control. CLC implements hardware fault-protection logic (over-current, over-temperature) without CPU involvement. Compared with a discrete analog LED driver, the integrated digital approach enables tunable white, RGB, and DMX-512 dimming profiles via firmware updates.
추천
Industrial Sensor Signal Conditioning
The PIC16LF1713-I/SO integrates two on-chip op-amps that provide analog front-end gain and filtering for bridge sensors, RTDs, and thermocouples, with the 10-bit ADC digitising the conditioned signal. PPS lets the engineer route the analog pins to physically convenient PCB locations, simplifying board layout in tight enclosures. The MCU's industrial -40C to +85C temperature range covers factory-floor deployments. In a typical load-cell application, two op-amps form an instrumentation-amp front end, eliminating the need for an external INA family chip and saving roughly USD 0.80 per channel.
추천
Consumer Appliance Control Board
The PIC16LF1713-I/SO is widely deployed in white-goods and small-appliance control boards because it integrates the user-interface (button matrix, LED indicators via PWM), the sensor network (temperature, water level), and the load-driver (relay, TRIAC, solenoid) interface in a single 28-SOIC part. EUSART and I2C interfaces support connectivity to a higher-end host MCU or to a Wi-Fi module for smart-appliance variants. The 7 KB program space accommodates small RTOS or state-machine firmware for washers, dryers, coffee machines, and microwave ovens. Its XLP modes keep standby power below 0.1 W to meet energy-efficiency regulations.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC16LF1713-I/SO — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC16F1713-I/SO | PIC16LF1713-E/SO | PIC16LF1709-I/SO |
|---|---|---|---|---|
| Package | 28-SOIC | 28-SOIC - same | 28-SOIC - same | 28-SOIC - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (Flash) | 7 KB | 7 KB | 7 KB | 3.5 KB |
| RAM | 512 bytes | 512 bytes | 512 bytes | 256 bytes |
| Operating Voltage | 1.8 V to 3.6 V | 1.8 V to 5.5 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Maximum Clock | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| ADC | 10-bit, 28 channels | 10-bit, 28 channels | 10-bit, 28 channels | 10-bit, 8 channels |
| Op-Amps | 2 | 2 | 2 | 1 |
| COG Peripheral | Yes | Yes | Yes | No |
| Temperature Grade | -40 C to +85 C | -40 C to +85 C | -40 C to +125 C | -40 C to +85 C |
주요 차별점
- Highest integrated analog plus Core-Independent Peripherals in the 28-SOIC PIC16F171x family (vs PIC16LF1709-I/SO)
- Lower-voltage / lower-power process for battery-powered designs (vs PIC16F1713-I/SO)
- Industrial temperature grade as standard ordering part (vs PIC16LF1713-E/SO)
설계 노트
Decouple VDD with a 0.1 uF ceramic capacitor placed within 5 mm of pin 20 (and pin 28 if both VDD pins are bonded). For battery applications, add a 10 uF bulk capacitor near VDD to handle inrush when the ADC or op-amps wake from sleep. The LF variant operates 1.8V to 3.6V; below 2.0 V the ADC accuracy degrades by ~1 LSB per 100 mV drop, so bias the reference accordingly.
Do not leave MCLR floating. Tie MCLR (pin 3) to VDD through a 10 kohm resistor, or to a supervisor IC if hardware reset is required. ICSP pins RB6/PGC (pin 16) and RB7/PGD (pin 15) must not be permanently pulled low; they interfere with in-circuit programming. When using the ADC, ensure the analog input pin is configured as analog (ANSEL bit set) before reading; PPS does not bypass this requirement.
Route analog inputs (RA0-RA5, RC0-RC7) away from digital switching traces such as PWM outputs and clock lines. The on-chip op-amps have limited PSRR above 100 kHz, so a quiet analog ground plane connected to VSS (pin 14 or 27) is recommended. For ZCD sensing, keep the AC coupling resistor within 10 mm of the ZCD pin to minimise noise pickup. Estimated: at 32 MHz, expect about 5 mA active current per the family datasheet DC characteristics.
When using the EUSART at high baud rates (above 250 kbps) keep the trace short and add a series resistor at the MCU end for source-termination. The SPI peripheral can run up to FOSC/2 = 16 MHz; add damping if the trace length exceeds 50 mm. The I2C peripheral requires external pull-up resistors in the 4.7 kohm to 10 kohm range on SDA and SCL; the weak pull-ups on RB4/RB5 are for keypress wake, not for bus termination.
규정 준수 정보
RoHS and lead-free compliant per Microchip product page; PIC16LF1713-I/SO is not AEC-Q100 qualified (industrial grade only).
