PIC18C452T-E/L - 32KB OTP 8-bit MCU, 44-PLCC | Microchip
부품 번호: PIC18C452T-E/L ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $17.2 | $172.00 |
| 100 | $15.85 | $1,585.00 |
| 500 | $14.4 | $7,200.00 |
| 1,000 | $13.1 | $13,100.00 |
PIC18C452T-E/L 개요
What is an 8-bit OTP microcontroller? An OTP (One-Time-Programmable) microcontroller is a microcontroller whose program memory is implemented as one-time-writable non-volatile storage - the bit cells can be written once by the user but cannot be erased electrically. This positions the PIC18C452 in the broader hierarchy of microcontrollers -> 8-bit MCUs -> OTP MCUs -> embedded controllers. Compared to flash-based MCUs, OTP parts offer lower per-unit cost in high-volume production and slightly smaller die area, while still preserving the same instruction set and peripheral set across the family.
Key features of the PIC18C452T-E/L include 10 MIPS throughput at 40 MHz, a 10-bit successive-approximation ADC with up to 8 input channels, a Master SSP (MSSP) module supporting SPI and I2C, a USART with addressable RX/TX buffering, two CCP modules, and an 8-bit parallel slave port (PSP). The device operates across an industrial temperature range of -40C to +125C and supports 2.0 V to 5.5 V supply. The enhanced (E) silicon variant provides wider Vdd and temperature tolerances than the baseline part.
Architecturally, the PIC18C452 uses a 16-bit instruction / 8-bit data Harvard architecture with 77 single-word instructions, single-cycle hardware multiplier, and a 32-level deep hardware stack. The CPU fetches a 16-bit instruction in one cycle and operates on 8-bit data via 12 special-function and 11 general-purpose register file banks. Two 8-bit timers and three 16-bit timers provide flexible capture, compare, and PWM event management.
Typical applications include industrial control panels, motor drive front-ends, instrumentation data logging, sensor signal conditioning, and embedded control blocks where the -E/L extended-temperature range and OTP cost model are required. The PIC18C452 is one of the original PIC18 family members; PIC18F452 flash variants are now the mainstream upgrade path with the same peripheral set, so many legacy designs are migrating footprints via drop-in compatible flash siblings.
When designing with this device, verify the supply decoupling network: place a 0.1 uF ceramic close to each Vdd/Vss pair and bulk capacitance on the analog supply AVdd/AVss pins. The MSSP module has a known silicon errata that must be reviewed before production commit.
This page synthesizes distributor pricing, drop-in alternative candidates, and practical design notes drawn from the verified Microchip datasheet - information not aggregated in the datasheet alone.
드롭인 대체품: PIC18C452T-E/L — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC18C452T-E/L (동일 폼 팩터 및 풋프린트) — 차이점: Package, ADC, Operating Temperature, Timers, Mounting Type.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC18F452-I/L
✅ 드롭인✓ 재고 있음
$6.85 / 개
데이터시트 보기 →PIC18F4520-I/L
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC18F452-I/P
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$5.1 / 개
데이터시트 보기 →PIC18C452-I/L
✅ 드롭인✓ 재고 있음
$7.94 / 개
데이터시트 보기 →PIC18C452T-E/L 최대 정격 & 전기적 특성
| Family | PIC18C |
| Series | PIC18C452 |
| Core | PIC 8-bit RISC (Harvard) |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 32 KB (16K x 16) |
| RAM Size | 1.5 KB (1.5K x 8) |
| EEPROM Size | 256 bytes |
| Maximum CPU Speed | 40 MHz / 10 MIPS |
| Instruction Cycle | 100 ns (at 40 MHz) |
| Number of I/O Pins | 33 |
| ADC | 10-bit, up to 8 input channels |
| Timer Modules | 2 x 8-bit + 3 x 16-bit |
| Communication Peripherals | MSSP (SPI/I2C), USART/SCI, PSP (8-bit parallel slave port) |
| CCP Modules | 2 |
| 공급 전압 | 2.0 V to 5.5 V |
| 동작 온도 | -40C to +125C (extended, E suffix) |
| 패키지 / 케이스 | 44-LCC (J-Lead), PLCC-44 |
| 실장 유형 | Surface Mount |
| Oscillator Type | External |
| Hardware Multiplier | 8 x 8 single-cycle |
| Hardware Stack | 32-level deep |
| Standard Packaging | Tape & Reel |
| RoHS 상태 | unknown |
| Mastering SSP (MSSP) Errata | Yes - review silicon errata sheet before production |
PIC18C452T-E/L 핀 구성
| 핀 1 | RA2/AN2/VREF- — Port A bit 2 / Analog input 2 / ADC negative reference |
| 핀 2 | RA3/AN3/VREF+ — Port A bit 3 / Analog input 3 / ADC positive reference |
| 핀 3 | RA4/T0CKI — Port A bit 4 / Timer0 clock input |
| 핀 4 | RA5/AN4/SS — Port A bit 5 / Analog input 4 / SPI slave select |
| 핀 5 | RE0/RD/AN5 — Port E bit 0 / Parallel Slave Port read / Analog input 5 |
| 핀 6 | RE1/WR/AN6 — Port E bit 1 / Parallel Slave Port write / Analog input 6 |
| 핀 7 | RE2/CS/AN7 — Port E bit 2 / Parallel Slave Port chip select / Analog input 7 |
| 핀 8 | OSC1/CLKIN — Oscillator input / external clock input |
| 핀 9 | OSC2/CLKOUT — Oscillator output / clock output |
| 핀 10 | VSS — Ground reference |
| 핀 11 | VDD — Positive supply |
| 핀 12 | RB0/INT0 — Port B bit 0 / External interrupt 0 |
| 핀 13 | RB1/INT1 — Port B bit 1 / External interrupt 1 |
| 핀 14 | RB2/INT2 — Port B bit 2 / External interrupt 2 |
| 핀 15 | RB3/CCP2 — Port B bit 3 / CCP2 module I/O |
| 핀 16 | RB4 — Port B bit 4 |
| 핀 17 | RB5 — Port B bit 5 |
| 핀 18 | RB6/PGC — Port B bit 6 / ICSP clock |
| 핀 19 | RB7/PGD — Port B bit 7 / ICSP data |
| 핀 20 | AVSS — Analog ground |
| 핀 21 | AVDD — Analog positive supply |
| 핀 22 | RC0/T1OSO/T1CKI — Port C bit 0 / Timer1 oscillator output / Timer1 clock input |
| 핀 23 | RC1/T1OSI/CCP2 — Port C bit 1 / Timer1 oscillator input / CCP2 alternate |
| 핀 24 | RC2/CCP1 — Port C bit 2 / CCP1 module I/O |
| 핀 25 | RC3/SCK/SCL — Port C bit 3 / SPI clock / I2C clock |
| 핀 26 | RC4/SDI/SDA — Port C bit 4 / SPI data in / I2C data |
| 핀 27 | RC5/SDO — Port C bit 5 / SPI data out |
| 핀 28 | RC6/TX/CK — Port C bit 6 / USART transmit / USART clock |
| 핀 29 | RC7/RX/DT — Port C bit 7 / USART receive / USART data |
| 핀 30 | RD0/PSP0 — Port D bit 0 / Parallel Slave Port bit 0 |
| 핀 31 | RD1/PSP1 — Port D bit 1 / Parallel Slave Port bit 1 |
| 핀 32 | RD2/PSP2 — Port D bit 2 / Parallel Slave Port bit 2 |
| 핀 33 | RD3/PSP3 — Port D bit 3 / Parallel Slave Port bit 3 |
| 핀 34 | RD4/PSP4 — Port D bit 4 / Parallel Slave Port bit 4 |
| 핀 35 | RD5/PSP5 — Port D bit 5 / Parallel Slave Port bit 5 |
| 핀 36 | RD6/PSP6 — Port D bit 6 / Parallel Slave Port bit 6 |
| 핀 37 | RD7/PSP7 — Port D bit 7 / Parallel Slave Port bit 7 |
| 핀 38 | VSS — Ground reference |
| 핀 39 | VDD — Positive supply |
| 핀 40 | RA0/AN0 — Port A bit 0 / Analog input 0 |
| 핀 41 | RA1/AN1 — Port A bit 1 / Analog input 1 |
| 핀 42 | MCLR/VPP — Master clear reset / Programming voltage input |
| 핀 43 | NC — Not connected (per datasheet PLCC-44 package) |
| 핀 44 | NC — Not connected (per datasheet PLCC-44 package) |
일반적인 애플리케이션
PIC18C452T-E/L 적합 용도: 6 애플리케이션s: Industrial Control Panels, Motor Drive Front-Ends, Instrumentation Data Logging, Sensor Signal Conditioning, Embedded Control Blocks, Legacy Avionics Subsystems.
Industrial Control Panels
The PIC18C452T-E/L's extended -40C to +125C operating range and 33 digital I/O pins make it suitable for industrial control panel front-ends that drive relays, read contactors, and execute discrete-time control loops. Its 10 MIPS throughput handles PID-like control cycles at kHz rates, while the 10-bit ADC samples transducer signals (pressure, temperature) with sufficient resolution for closed-loop feedback. The OTP cost model favors high-volume panel builders who lock firmware once and ship thousands of units without ISP needs.
추천
Motor Drive Front-Ends
The PIC18C452T-E/L can host the supervisory state machine for small motor drives: ADC samples current shunts, the 16-bit timer drives PWM carrier generation in concert with one of the two CCP modules, and the USART handles command/status exchange with a master controller. The 100 ns instruction cycle supports 10 kHz PWM update rates while leaving headroom for housekeeping. The MSSP module interfaces to a digital hall-effect sensor chain over SPI, completing the sensor-fusion front-end.
추천
Instrumentation Data Logging
With 1.5 KB of RAM and 256 bytes of EEPROM, the PIC18C452T-E/L is well suited to log sensor frames into external storage via SPI. The MSSP module connects directly to an external EEPROM or SD-card front-end, while the 10-bit ADC captures instrumentation signals at the system sampling rate. The 32 KB OTP holds the logging firmware and serialization code, and the USART pumps results out to a host PC when maintenance is performed.
추천
Sensor Signal Conditioning
The PIC18C452T-E/L's 10-bit ADC with up to 8 channels, combined with its MSSP for digital sensor readout, supports multi-sensor conditioning hubs in industrial environments. The 33 I/O lines interface to analog front-ends, while two CCP modules generate PWM excitation signals for bridge-type sensors. Running at 10 MIPS, the MCU can poll, filter, and apply linearization in real time before forwarding calibrated readings over the USART.
추천
Embedded Control Blocks
As an embedded control block in larger equipment, the PIC18C452T-E/L handles housekeeping, error monitoring, and user-interface tasks while dedicated DSP or FPGA cores handle signal processing. The PSP (8-bit parallel slave port) lets it communicate bidirectionally with a host CPU, while MSSP and USART expose it to a debug/maintenance channel. The -E extended temperature grade and 33 I/O pins support industrial-cabinet deployment without active cooling.
추천
Legacy Avionics Subsystems
Because the PIC18C452 family was widely designed into long-life avionics and military subsystems during the late 1990s, the PIC18C452T-E/L is still demanded for spares and form-fit-function replacements on existing equipment. Its -40C to +125C operating range, 33 I/O, and 10-bit ADC satisfy legacy sensor and actuator interfaces. The OTP memory ensures deterministic code that cannot be inadvertently overwritten in field service.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC18C452T-E/L — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC18F452-I/L | PIC18F4520-I/L | PIC18F452-I/P | PIC18C452-I/L |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-LCC (J-Lead) PLCC | 44-LCC (J-Lead) PLCC - same | 44-LCC (J-Lead) PLCC - same | 40-PDIP (different footprint) | 44-LCC (J-Lead) PLCC - same |
| Program Memory | 32 KB OTP | 32 KB flash | 32 KB flash | 32 KB flash | 32 KB OTP |
| RAM Size | 1.5 KB | 1.5 KB | 1.5 KB | 1.5 KB | 1.5 KB |
| Maximum Frequency | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS | 40 MHz / 10 MIPS |
| Operating Temperature | -40C to +125C (E) | -40C to +85C (I) | -40C to +85C (I) | -40C to +85C (I) | -40C to +85C (I) |
| ADC Resolution | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels |
| Lifecycle Status | Obsolete | Active / Mature | Active | Active / Mature | Obsolete |
주요 차별점
- Extended -40C to +125C industrial temperature grade (vs PIC18C452-I/L)
- Tape & Reel packaging for high-volume SMT assembly (vs PIC18C452-E/L (tray))
- OTP memory at lower per-unit cost versus flash siblings (vs PIC18F452-I/L)
설계 노트
Place a 0.1 uF decoupling capacitor as close as possible to each Vdd/Vss pin pair on the PIC18C452T-E/L, plus a bulk 10 uF tantalum or ceramic on the analog supply rail (AVdd/AVss). The MCU's 33 I/O lines and ADC switching create instantaneous supply transients; insufficient decoupling couples digital noise into the analog reference and corrupts 10-bit ADC readings. Use a star-ground topology tying AVss back to Vss at a single point.
Review the Microchip PIC18C452 silicon errata sheet before committing to production. The MSSP module has documented anomalous behavior that must be handled in firmware. The /E temperature variant must be ordered explicitly when extended -40C to +125C range is required - the /I variant stops at +85C and is a different die test grade.
Route the oscillator pins (OSC1/OSC2) with short traces and a guard ground to minimize EMI pickup. For 40 MHz operation, keep the trace length below 5 mm and place load capacitors within 3 mm of the oscillator pins. The ICSP pins (RB6/PGC, RB7/PGD) must remain accessible in the PCB layout for factory programming of the OTP array.
Separate analog and digital ground planes under the PIC18C452T-E/L. Tie analog inputs (Port A) and the AVdd/AVss pair to the analog plane only; route digital return currents around the analog island. The PLCC-44 socket footprint is recommended for prototype builds to allow swap-out during firmware development; surface-mount soldering requires a hot-air rework station for OTP re-programming iterations.
규정 준수 정보
Compliance status not explicitly stated in the verified web data; the part predates Microchip's formal RoHS transition for many OTP-MCU lines. AEC-Q100 automotive qualification is not applicable to the PIC18C452 family; choose PIC18F452-I/PT automotive-grade siblings if required.