PIC18F8585T-I/PT - 48KB Flash 8-bit MCU, TQFP-80 | Microchip
부품 번호: PIC18F8585T-I/PT ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $18.47 | $18.47 |
| 10 | $16.85 | $168.50 |
| 100 | $14.92 | $1,492.00 |
| 500 | $13.18 | $6,590.00 |
| 1,000 | $11.75 | $11,750.00 |
PIC18F8585T-I/PT 개요
A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals. The 8-bit MCU class uses an 8-bit data path and instruction word widths of 16 bits (PIC18). Microcontrollers sit within the broader hierarchy: microcontroller -> embedded processor -> semiconductor IC. PIC18 devices target applications requiring deterministic real-time control, low power, and rich peripheral integration at low cost.
Key features include: 48KB self-programmable Flash, 3328 bytes SRAM, 1024 bytes EEPROM, hardware multiplier, 16-bit timers, 10-bit ADC with up to 16 channels, two USARTs, MSSP (SPI/I2C), CAN module, parallel slave port, and a 5-bit/8-bit parallel port. The wide operating range supports automotive (-40C to +125C) and industrial environments. Five 8-bit I/O ports (PORTA-PORTE) plus PORTF/PORTG provide 70 general-purpose I/O lines. Two capture/compare/PWM modules and enhanced CCP add flexible motor-control capability.
Internally, the PIC18F8585 uses a 16-bit Harvard architecture with pipelined instruction fetch and an 8-bit ALU plus hardware multiply. The enhanced instruction set includes C-optimized constructs and bit manipulation. A 10-channel, 10-bit ADC supports both single-ended and differential conversions for sensor acquisition. An integrated CAN 2.0B controller and parallel port make the device suited to industrial networking and instrumentation.
Typical applications include industrial control panels, automotive body and HVAC modules, security and access systems, medical instrumentation, and HVAC controllers. The high pin count (80 TQFP) accommodates parallel LCD interfaces, multiple UART links, and large I/O expansion, while the 5V-tolerant I/O simplifies interfacing to legacy 5V peripherals.
A key design consideration: at 40 MHz, the supply current draw requires proper decoupling - place a 100nF ceramic capacitor on each VDD/VSS pair close to the pins, plus a bulk 10uF tantalum or ceramic capacitor near the IC. In-Circuit Serial Programming (ICSP) requires dedicated ICSPCLK/ICSPDAT pins routed with short traces to the programming header to prevent signal integrity issues.
This page synthesizes distributor pricing, drop-in 80-pin TQFP alternatives, and practical design notes not found in the manufacturer datasheet, enabling faster component selection for engineers and procurement teams.
드롭인 대체품: PIC18F8585T-I/PT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC18F8585T-I/PT (동일 폼 팩터 및 풋프린트) — 차이점: Package, Core Architecture, Program Memory (Flash), ADC, Operating Temperature.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC18F8585-I/PT
✅ 드롭인✓ 재고 있음
$11.05 / 개
데이터시트 보기 →PIC18F8585-E/PT
✅ 드롭인✓ 재고 있음
$9.55 / 개
데이터시트 보기 →PIC18F8585T-I/PT
✅ 드롭인✓ 재고 있음
$11.75 / 개
데이터시트 보기 →PIC18F67K90-I/PT
✅ 드롭인✓ 재고 있음
$7.55 / 개
데이터시트 보기 →PIC18F66K90-I/PT
✅ 드롭인✓ 재고 있음
$4.15 / 개
데이터시트 보기 →PIC18F8520-I/PT
✅ 드롭인✓ 재고 있음
$5.1586 / 개
데이터시트 보기 →PIC18F8585T-I/PT 최대 정격 & 전기적 특성
| Core Processor | PIC |
| Core Size | 8-bit |
| Series | PIC18F |
| Program Memory Size | 48KB (24K x 16) |
| RAM Size | 3.25KB (3328 x 8) |
| EEPROM Size | 1024 bytes |
| Maximum Clock Speed | 40 MHz |
| MIPS | 10 MIPS |
| Supply Voltage (Vcc/Vdd) | 4.2 V to 5.5 V |
| I/O Pins | 70 |
| ADC | 10-bit, up to 16 channels |
| Connectivity | I2C, SPI, UART, CAN, Parallel |
| Peripherals | Brown-out Detect/Reset, LVD, POR, PWM, WDT |
| Number of Timers | 4 (16-bit) |
| 데이터 버스 폭 | 16-bit |
| 동작 온도 | -40C to +85C (Industrial) |
| 패키지 | 80-TQFP (12x12 mm) |
| 실장 유형 | Surface Mount |
| ROM Type | Flash |
| RoHS 상태 | Compliant |
PIC18F8585T-I/PT 핀 구성
| 핀 1 | OSC1 — Oscillator input / external clock input |
| 핀 2 | OSC2 — Oscillator output |
| 핀 3 | MCLR — Master clear reset (active low) |
| 핀 4 | RA0/AN0 — PORTA bit 0 / Analog input 0 |
| 핀 5 | RA1/AN1 — PORTA bit 1 / Analog input 1 |
| 핀 6 | RA2/AN2 — PORTA bit 2 / Analog input 2 |
| 핀 7 | RA3/AN3/VREF+ — PORTA bit 3 / Analog input 3 / ADC VREF+ |
| 핀 8 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| 핀 9 | RA5/AN4/SS — PORTA bit 5 / Analog input 4 / SPI slave select |
| 핀 10 | VDD — Positive supply voltage |
| 핀 11 | VSS — Ground reference |
| 핀 12 | RA6/OSC2 — PORTA bit 6 / alternate oscillator output |
| 핀 13 | RA7/OSC1 — PORTA bit 7 / alternate oscillator input |
| 핀 14 | RB0/INT0 — PORTB bit 0 / External interrupt 0 |
| 핀 15 | RB1/INT1 — PORTB bit 1 / External interrupt 1 |
| 핀 16 | RB2/INT2 — PORTB bit 2 / External interrupt 2 |
| 핀 17 | RB3/CCP2 — PORTB bit 3 / CCP2 I/O |
| 핀 18 | RB4 — PORTB bit 4 (interrupt-on-change) |
| 핀 19 | RB5/PGM — PORTB bit 5 / LVP programming |
| 핀 20 | RB6/PGC — PORTB bit 6 / ICSP clock |
| 핀 21 | RB7/PGD — PORTB bit 7 / ICSP data |
| 핀 22 | VDD — Positive supply voltage |
| 핀 23 | VSS — Ground reference |
| 핀 24 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator / clock |
| 핀 25 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator / CCP2 |
| 핀 26 | RC2/CCP1 — PORTC bit 2 / CCP1 I/O |
| 핀 27 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| 핀 28 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| 핀 29 | RC5/SDO — PORTC bit 5 / SPI data out |
| 핀 30 | RC6/TX1/CK1 — PORTC bit 6 / USART1 TX / clock |
| 핀 31 | RC7/RX1/DT1 — PORTC bit 7 / USART1 RX / data |
| 핀 32 | RD0/PSP0 — PORTD bit 0 / Parallel Slave Port bit 0 |
| 핀 33 | RD1/PSP1 — PORTD bit 1 / Parallel Slave Port bit 1 |
| 핀 34 | RD2/PSP2 — PORTD bit 2 / Parallel Slave Port bit 2 |
| 핀 35 | RD3/PSP3 — PORTD bit 3 / Parallel Slave Port bit 3 |
| 핀 36 | RC4/PSP4 — PORTD bit 4 / Parallel Slave Port bit 4 |
| 핀 37 | RD5/PSP5 — PORTD bit 5 / Parallel Slave Port bit 5 |
| 핀 38 | RD6/PSP6/TX2/CK2 — PORTD bit 6 / PSP6 / USART2 TX |
| 핀 39 | RD7/PSP7/RX2/DT2 — PORTD bit 7 / PSP7 / USART2 RX |
| 핀 40 | VSS — Ground reference |
| 핀 41 | VDD — Positive supply voltage |
| 핀 42 | RE0/RD/AN5 — PORTE bit 0 / Read control / AN5 |
| 핀 43 | RE1/WR/AN6 — PORTE bit 1 / Write control / AN6 |
| 핀 44 | RE2/CS/AN7 — PORTE bit 2 / Chip select / AN7 |
| 핀 45 | RE3 — PORTE bit 3 |
| 핀 46 | RF0/AN8 — PORTF bit 0 / Analog input 8 |
| 핀 47 | RF1/AN9/C2OUT — PORTF bit 1 / AN9 / Comparator 2 output |
| 핀 48 | RF2/AN10/C1OUT — PORTF bit 2 / AN10 / Comparator 1 output |
| 핀 49 | RF3/AN11 — PORTF bit 3 / Analog input 11 |
| 핀 50 | RF4/AN12 — PORTF bit 4 / Analog input 12 |
| 핀 51 | RF5/AN13 — PORTF bit 5 / Analog input 13 |
| 핀 52 | RF6/AN14 — PORTF bit 6 / Analog input 14 |
| 핀 53 | RF7/AN15 — PORTF bit 7 / Analog input 15 |
| 핀 54 | RG0 — PORTG bit 0 |
| 핀 55 | RG1 — PORTG bit 1 |
| 핀 56 | RG2 — PORTG bit 2 |
| 핀 57 | RG3 — PORTG bit 3 |
| 핀 58 | RG4 — PORTG bit 4 |
| 핀 59 | MCLR/RA5 — PORTE alternate / RA5 secondary function |
| 핀 60 | VDD — Positive supply voltage |
| 핀 61 | VSS — Ground reference |
| 핀 62 | CANRX — CAN bus receive input |
| 핀 63 | CANTX — CAN bus transmit output |
| 핀 64 | RH0 — PORTH bit 0 |
| 핀 65 | RH1 — PORTH bit 1 |
| 핀 66 | RH2 — PORTH bit 2 |
| 핀 67 | RH3 — PORTH bit 3 |
| 핀 68 | RH4 — PORTH bit 4 |
| 핀 69 | RH5 — PORTH bit 5 |
| 핀 70 | RH6 — PORTH bit 6 |
| 핀 71 | RH7 — PORTH bit 7 |
| 핀 72 | RJ0 — PORTJ bit 0 |
| 핀 73 | RJ1 — PORTJ bit 1 |
| 핀 74 | RJ2 — PORTJ bit 2 |
| 핀 75 | RJ3 — PORTJ bit 3 |
| 핀 76 | RJ4 — PORTJ bit 4 |
| 핀 77 | RJ5 — PORTJ bit 5 |
| 핀 78 | RJ6 — PORTJ bit 6 |
| 핀 79 | RJ7 — PORTJ bit 7 |
| 핀 80 | VSS — Ground reference |
일반적인 애플리케이션
PIC18F8585T-I/PT 적합 용도: 6 애플리케이션s: Industrial Control Panels, Automotive Body and HVAC Modules, Security and Access Control Systems, Medical Instrumentation, HVAC and Building Automation Controllers, Point-of-Sale Terminals and Printers.
Industrial Control Panels
The PIC18F8585T-I/PT fits industrial control panels because of its 70 GPIO, two USARTs for Modbus RTU/RS-485, CAN bus for fieldbus, and 16-channel 10-bit ADC for analog sensor inputs (temperature, pressure, level). Operating from 4.2V to 5.5V with -40C to +85C industrial rating, it survives factory-floor temperature swings. The 48KB Flash supports ladder-logic firmware plus Modbus/CANopen stacks, while 3328 bytes SRAM handles communication buffers. Brown-out reset and LVD protect against supply glitches common in motor-driven cabinets. The 80-pin TQFP footprint exposes enough I/O for push-button matrix scanning, relay drivers, and segmented LCD interfaces.
추천
Automotive Body and HVAC Modules
The PIC18F8585T-I/PT suits automotive body and HVAC control modules where CAN bus connectivity, PWM motor control, and 5V-tolerant GPIO drive sensor-actuator networks. The integrated CAN 2.0B controller interfaces directly with vehicle bus networks, while four 16-bit timers with PWM drive blower fans, blend doors, and stepper motors. 70 GPIO accommodate multiplexed switch inputs, LED drivers, and LIN slave bridges. The industrial -40C to +85C rating handles cabin temperature ranges; for under-hood (up to +125C), the PIC18F8585-E/PT variant is preferred. The 48KB Flash supports CAN stack, OBD-II diagnostics, and HVAC control algorithms simultaneously.
추천
Security and Access Control Systems
The PIC18F8585T-I/PT is well-matched to security and access control panels requiring multiple serial interfaces, keypad scanning, and LCD display driving. Two USARTs allow simultaneous connection to a central monitoring station and a peripheral reader (card reader, biometric scanner), while MSSP in SPI mode interfaces Wiegand readers or AES-encrypted keypads. The 16-channel ADC monitors battery voltage, tamper switches, and PIR sensor analog outputs. With 48KB Flash, firmware can include AES encryption routines, event logging, and RTC handling. The 70 GPIO easily drives 4x4 keypads, status LEDs, and relay-controlled door strikes without external I/O expanders.
추천
Medical Instrumentation
The PIC18F8585T-I/PT serves in medical instrumentation front-ends where multiple analog channels, isolated serial links, and deterministic 8-bit control are needed. The 16-channel 10-bit ADC digitizes signals from temperature sensors, pressure transducers, and impedance-measurement front-ends; 70 GPIO controls front-panel switches, status LEDs, and segment LCD multiplexing. Two USARTs connect to a host PC for data logging and to a calibration module over RS-232/485. The 5V-tolerant I/O simplifies interfacing to legacy medical-grade 5V analog front-ends. Industrial -40C to +85C rating suits laboratory and bedside equipment; for higher reliability, the -E variant (-40C to +125C) is recommended.
추천
HVAC and Building Automation Controllers
The PIC18F8585T-I/PT fits HVAC and building automation controllers that need to manage multiple zone sensors, valve actuators, and communication with a central BMS. The CAN bus interfaces BACnet or vendor-specific building automation protocols, while USARTs link to legacy RS-485 Modbus networks. The 16-channel ADC reads thermistor temperature sensors, humidity probes, and pressure transducers with 10-bit resolution sufficient for setpoint control. PWM outputs drive damper motors and pulse-width-modulated valves. The 48KB Flash accommodates scheduling, PID control loops, and protocol stacks simultaneously; 3328 bytes RAM handles Modbus and BACnet buffers.
추천
Point-of-Sale Terminals and Printers
The PIC18F8585T-I/PT drives point-of-sale terminals and receipt printers where multiple peripheral interfaces, keypad scanning, and LCD/character display control are essential. Two USARTs connect to magnetic-stripe readers and external printers, while MSSP in SPI mode drives graphical or alphanumeric LCD controllers. The 70 GPIO easily handles 4x5 keypad matrices, multiple status LEDs, and buzzer/piezo driver lines. The 16-channel ADC monitors power supply voltage, battery state, and paper sensors. With 48KB Flash, firmware can include custom fonts, USB stacks, and transaction logging. The 5V operation simplifies interfacing to legacy POS peripherals.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC18F8585T-I/PT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC18F8585-I/PT | PIC18F8585-E/PT | PIC18F67K90-I/PT | PIC18F66K90-I/PT | PIC18F8520-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-TQFP (12x12 mm) | 80-TQFP (12x12 mm) - same | 80-TQFP (12x12 mm) - same | 80-TQFP (12x12 mm) - same | 80-TQFP (12x12 mm) - same | 80-TQFP (12x12 mm) - same |
| Lifecycle Status | NRND | NRND | NRND | Active | Active | NRND |
| Program Memory (Flash) | 48 KB (24K x 16) | 48 KB (24K x 16) | 48 KB (24K x 16) | 64 KB | 64 KB | 32 KB |
| Maximum Clock Speed | 40 MHz (10 MIPS) | 40 MHz (10 MIPS) | 40 MHz (10 MIPS) | 64 MHz (16 MIPS) | 64 MHz (16 MIPS) | 40 MHz (10 MIPS) |
| Operating Voltage | 4.2 V to 5.5 V | 4.2 V to 5.5 V | 4.2 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 2.0 V to 5.5 V |
| Operating Temperature | -40C to +85C (I grade) | -40C to +85C (I grade) | -40C to +125C (E grade) | -40C to +85C (I grade) | -40C to +85C (I grade) | -40C to +85C (I grade) |
| ADC Resolution | 10-bit (16 channels) | 10-bit (16 channels) | 10-bit (16 channels) | 12-bit (24 channels) | 12-bit (24 channels) | 10-bit (16 channels) |
| Approx. Unit Price (qty 1) | $18.47 | ~$18.47 | ~$20.50 | ~$7.20 | ~$6.80 | ~$15.00 |
주요 차별점
- Larger program memory (48 KB) vs PIC18F8520 family (vs PIC18F8520-I/PT)
- Industrial temperature range standard on -I grade (vs PIC18F8585-E/PT)
- Modern migration path with same footprint (vs PIC18F67K90-I/PT)
- NRND status requires migration planning (vs PIC18F67K90-I/PT)
설계 노트
Place a 100 nF ceramic decoupling capacitor on each VDD/VSS pin pair, with the capacitor lead length less than 2 mm to minimize parasitic inductance. Add a bulk 10 uF ceramic or tantalum capacitor at the IC supply entry. The PIC18F8585 datasheet specifies a maximum 40 MHz operating frequency requiring stable 4.2V-5.5V supply; use a low-noise LDO such as MCP1700 or a switching regulator with adequate output ripple filtering to keep digital supply noise below 50 mVpp. For battery-powered applications, leverage the PIC18's sleep mode and BOR to minimize quiescent current.
Route the ICSP programming signals (ICSPCLK/ICSPDAT, also shared with RB6/RB7) with short traces directly to a 6-pin programming header, keeping the trace length under 50 mm. Add ESD protection diodes on the MCLR pin (or use Microchip's recommended MCP130 reset supervisor). For TQFP-80 packages, use a 4-layer PCB with continuous ground plane directly under the IC to reduce EMI; signal traces on outer layers should not cross the ground plane split. Maintain at least 0.2 mm clearance between analog and digital signal traces to prevent ADC crosstalk.
Do not exceed 5.5V on VDD - the PIC18F8585 is not 3.3V tolerant at full speed and overvoltage can permanently damage the silicon. When using the analog channels (AN0-AN15), configure unused ADC pins as digital outputs or leave them disabled to reduce shoot-through current. The MCLR pin must NOT be left floating; either tie to VDD through a 10 kohm pull-up or use the internal MCLR enable configuration. For CAN bus designs, always include a 120 ohm termination resistor at each end of the bus and a common-mode choke for EMI suppression.
규정 준수 정보
RoHS and REACH compliant per Microchip product declaration. The 'I' suffix denotes industrial temperature grade (-40C to +85C); the 'E' suffix variant is automotive-extended (-40C to +125C). For AEC-Q100 qualified parts, consider PIC18F-K40 automotive families.
