PIC18LF45K50T-I/MV - 8-bit MCU 32KB Flash 48MHz USB | Microchip
부품 번호: PIC18LF45K50T-I/MV ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $3.34 | $3.34 |
| 10 | $3.01 | $30.10 |
| 100 | $2.45 | $245.00 |
| 500 | $2.1 | $1,050.00 |
| 1,000 | $1.85 | $1,850.00 |
PIC18LF45K50T-I/MV 개요
A microcontroller (MCU) is a single-chip computer containing a CPU, non-volatile program memory (Flash), volatile working memory (RAM), peripherals, and I/O. It belongs to the category hierarchy: microcontroller -> embedded processor -> integrated circuit -> semiconductor. The PIC18LF45K50 family adds a hardware USB peripheral that is rare in low-pin-count 8-bit MCUs, eliminating the need for an external USB transceiver.
Key features include 32 KB self-programmable Flash (16K x 16), 2 KB RAM, 256 B EEPROM, 25 to 35 digital I/O pins depending on package, a 12-channel 10-bit ADC with auto-acquisition, two analog comparators, two 8-bit timers and three 16-bit timers, an enhanced Capture/Compare/PWM (ECCP) module, and an mTouch capacitive sensing peripheral. The integrated USB 2.0 full-speed transceiver and on-chip 3.3 V regulator make it a strong fit for HID, CDC, and vendor-class USB devices.
The 'LF' prefix denotes the wide-voltage low-power variant (1.8 V to 3.6 V), enabling direct Li-ion battery operation. nanoWatt XLP technology provides sleep currents below 100 nA typical, supporting battery-powered designs with multi-year standby lifetime. The 48 MHz internal oscillator eliminates the external crystal typically required by USB devices.
Typical applications include USB human-interface devices (HIDs) such as keyboards and mice, USB-to-UART bridges, USB sensor dongles, capacitive touch interfaces, low-cost data loggers, and consumer peripherals. The exposed thermal pad on the UQFN package aids heat dissipation for high-I/O USB applications.
When designing with this part, place a 1 uF decoupling capacitor close to each VDD pin and connect the exposed pad (EP) to a solid ground plane. Configure the internal USB regulator through the CONFIG3L register before enumerating; failure to do so will prevent USB detection.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: PIC18LF45K50T-I/MV — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC18LF45K50T-I/MV (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Operating Temperature, Comparators, Package, Communication.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC18LF45K50-I/MV
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC18LF45K50-E/MV
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC18LF45K42-I/MV
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC18LF45K40-I/MV
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$1.7 / 개
데이터시트 보기 →PIC18LF45K50T-I/MV 최대 정격 & 전기적 특성
| Family | PIC18LFxxK50 (PIC18 XLP) |
| Core | 8-bit PIC RISC (49 instruction set) |
| Program Memory | 32 KB Flash (16K x 16) |
| RAM | 2 KB |
| EEPROM | 256 B |
| Maximum CPU Frequency | 48 MHz |
| Operating Voltage (LF) | 1.8 V to 3.6 V |
| ADC | 10-bit, up to 25 channels (HDR + DDR) |
| Timers | 2 x 8-bit, 3 x 16-bit |
| USB | USB 2.0 Full-Speed (12 Mbps) with on-chip transceiver |
| Comparators | 2 analog comparators |
| 패키지 | 40-pin UQFN (MV) 5x5 mm with EP |
| 동작 온도 | -40 C to +85 C (industrial) |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant |
PIC18LF45K50T-I/MV 핀 구성
| 핀 1 | RA2/AN2 — Digital I/O / analog input 2 |
| 핀 2 | RA3/AN3 — Digital I/O / analog input 3 / VREF+ |
| 핀 3 | RA4/AN4 — Digital I/O / analog input 4 |
| 핀 4 | RA5/AN5 — Digital I/O / analog input 5 / VREF- |
| 핀 5 | VDD — Positive supply 1.8 V to 3.6 V (LF) |
| 핀 6 | VSS — Ground reference |
| 핀 7 | RA7 — Digital I/O |
| 핀 8 | RA6 — Digital I/O / oscillator |
| 핀 9 | RC0 — Digital I/O |
| 핀 10 | RC1 — Digital I/O |
| 핀 11 | RC2 — Digital I/O |
| 핀 12 | RC3 — Digital I/O |
| 핀 13 | RC4/D-/VMO — USB D- data line |
| 핀 14 | RC5/D+/VPO — USB D+ data line |
| 핀 15 | RC6 — Digital I/O / TX |
| 핀 16 | RC7 — Digital I/O / RX |
| 핀 17 | RB0/AN12 — Digital I/O / analog input 12 / interrupt |
| 핀 18 | RB1/AN10 — Digital I/O / analog input 10 |
| 핀 19 | RB2/AN8 — Digital I/O / analog input 8 |
| 핀 20 | RB3/AN9 — Digital I/O / analog input 9 |
| 핀 21 | RB4/AN11 — Digital I/O / analog input 11 |
| 핀 22 | RB5/AN13 — Digital I/O / analog input 13 |
| 핀 23 | RB6/PGC — Digital I/O / ICSP clock |
| 핀 24 | RB7/PGD — Digital I/O / ICSP data |
| 핀 25 | VUSB — USB 3.3 V internal regulator output (decouple 220 nF) |
| 핀 26 | RD0 — Digital I/O |
| 핀 27 | RD1 — Digital I/O |
| 핀 28 | RD2 — Digital I/O |
| 핀 29 | RD3 — Digital I/O |
| 핀 30 | RD4 — Digital I/O |
| 핀 31 | RD5 — Digital I/O |
| 핀 32 | RD6 — Digital I/O |
| 핀 33 | RD7 — Digital I/O |
| 핀 34 | RE0 — Digital I/O |
| 핀 35 | RE1 — Digital I/O |
| 핀 36 | RE2 — Digital I/O |
| 핀 37 | RE3 — Digital I/O (input only per datasheet) |
| 핀 38 | AVDD — Analog positive supply |
| 핀 39 | AVSS — Analog ground |
| 핀 40 | EP — Exposed thermal pad - connect to ground |
일반적인 애플리케이션
PIC18LF45K50T-I/MV 적합 용도: 6 애플리케이션s: USB Human Interface Device (HID), USB-to-UART Bridge, Capacitive Touch Sensor Interface (mTouch), USB Sensor Dongle, Battery-Powered Data Logger, Consumer LED Lighting Controller.
USB Human Interface Device (HID)
The PIC18LF45K50T-I/MV is purpose-built for USB HID designs such as keyboards, mice, gamepads, and custom input devices. Its integrated USB 2.0 full-speed transceiver with on-chip 3.3 V regulator eliminates the external USB interface IC normally required on low-pin MCUs, reducing BOM cost by $0.30-$0.50 per unit. The 48 MHz internal oscillator removes the 12 MHz crystal requirement, and the 32 KB Flash holds full HID class descriptors and report logic. nanoWatt XLP sleep currents below 100 nA typical enable multi-year battery life on wireless HID peripherals. The UQFN-40 5x5 mm footprint is ideal for compact consumer peripherals.
추천
USB-to-UART Bridge
The PIC18LF45K50T-I/MV makes an effective USB-to-UART bridge (CDC class) for connecting legacy RS-232 equipment to modern PCs that lack serial ports. The integrated USB transceiver enumerates as a virtual COM port on Windows/macOS/Linux without driver installation, while the EUSART peripheral provides 115200 baud native RS-232 output. The 2 KB RAM comfortably buffers UART traffic, and the 1.8 V to 3.6 V supply supports direct Li-ion battery operation for portable bridge dongles. This topology is widely used in industrial programming cables and sensor adapters.
추천
Capacitive Touch Sensor Interface (mTouch)
The PIC18LF45K50T-I/MV integrates Microchip's mTouch capacitive sensing module, supporting up to 13 touch channels without external components. The CTMU peripheral charges an internal capacitor and measures discharge time through a touch pad, resolving capacitance differences of femtofarads with the 10-bit ADC. This makes the K50 a fit for appliance control panels, proximity wake-up sensors, and slider/wheel interfaces. Combined with USB enumeration, the same MCU can serve as both the touch controller and USB-CDC/HID reporting channel, reducing system cost and PCB area in a 40-UQFN footprint.
추천
USB Sensor Dongle
The PIC18LF45K50T-I/MV is widely deployed in USB sensor dongles that report environmental, biometric, or industrial data to a host PC. The 12-channel 10-bit ADC acquires analog sensor signals, and the 32 KB Flash holds TinyUSB stack, sensor drivers, and HID/CDF report logic. USB bus-powered dongles draw up to 500 mA from the host; the on-chip 3.3 V regulator supplies the MCU and sensors without an external LDO. Low-power sleep modes allow the dongle to quiesce below 100 nA between sample intervals.
추천
Battery-Powered Data Logger
The PIC18LF45K50T-I/MV's nanoWatt XLP technology and 1.8 V to 3.6 V supply range make it a strong fit for battery-powered data loggers that periodically wake, sample, and return to sleep. The 32 KB Flash records time-stamped data with wear-leveling ECC, while the 2 KB RAM buffers samples between writes. nanoWatt XLP provides < 100 nA sleep current, so a 2000 mAh Li-ion cell supports months to years of unattended logging depending on duty cycle. USB enumeration on connection allows battery charging and data dump without separate connectors.
추천
Consumer LED Lighting Controller
The PIC18LF45K50T-I/MV drives WS2812B / APA102 addressable LED strips through PWM or bit-banged SPI, while a USB-CDC interface accepts commands from a host PC or smartphone bridge. The 25 mA I/O source/sink directly drives small MOSFET gates for high-side LED switching, and the ECCP module produces 16-bit PWM resolution for smooth color fades. The wide 1.8 V to 3.6 V supply matches single-cell Li-ion or 3.3 V regulated USB supplies. Designers use the K50 in DMX512-over-USB controllers, pixel-art wall displays, and ambient lighting systems.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC18LF45K50T-I/MV — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC18LF45K50-I/MV | PIC18LF45K50-E/MV | PIC18LF45K42-I/MV | PIC18LF45K40-I/MV |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 40-pin UQFN (MV) 5x5 | 40-pin UQFN (MV) 5x5 - same | 40-pin UQFN (MV) 5x5 - same | 40-pin UQFN (MV) 5x5 - same | 40-pin UQFN (MV) 5x5 - same |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 16 KB (-50%) |
| RAM | 2 KB | 2 KB | 2 KB | 2 KB | 1 KB (-50%) |
| USB Peripheral | USB 2.0 FS integrated | USB 2.0 FS integrated | USB 2.0 FS integrated | USB 2.0 FS integrated | No USB peripheral |
| Operating Voltage | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Temperature Grade | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) | -40 C to +125 C (extended) | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) |
| Shipping Format | Tape & Reel (T suffix) | Tray (no T suffix) | Tray or Tube | Tray | Tray |
주요 차별점
- Integrated USB 2.0 full-speed transceiver eliminates external USB IC (vs PIC18LF45K40-I/MV)
- 48 MHz internal oscillator eliminates external crystal for USB operation (vs PIC16F1455)
- Industry-standard PIC18 core with mature USB stack and bootloader (vs PIC18LF45K42-I/MV)
설계 노트
Decouple the VDD pin with a 100 nF ceramic capacitor placed within 3 mm of the pin, and add a bulk 1 uF to 10 uF tantalum or ceramic capacitor. The internal USB 3.3 V regulator on the VUSB pin requires its own 220 nF decoupling capacitor per the datasheet. Failure to decouple VUSB prevents USB enumeration and may cause host-side device-not-recognized errors.
Connect the exposed pad (EP) of the UQFN-40 package to a continuous ground plane with at least 8 thermal vias. The EP provides the primary heat-dissipation path; floating it raises junction temperature by 20-30 C at full USB load (bus-powered sensors pulling 200 mA). Estimated: with 4-layer 1 oz copper and 8 thermal vias, theta_JA drops below 30 C/W versus 60 C/W for EP floating.
Route the USB D+ (RC5) and D- (RC4) lines as a 90 ohm differential pair with matched length to within 150 mil. Place the 15 kohm pull-up resistor on D+ close to the MCU; per USB spec, the pull-up signals full-speed connection. Maintain a clearance of 90 mils under the pair to avoid coupling from other signals; this is critical for USB-IF compliance.
The CONFIG3L register must enable the internal USB voltage regulator (VREGEN = 1) before USB pins become functional. Forgetting this is the most common K50 firmware issue and produces 'device not recognized' on the host. Additionally, the LF (low-voltage) variant only operates down to 1.8 V; below that, oscillator start-up fails and the device stays in reset.
규정 준수 정보
RoHS and REACH compliant per Microchip material declarations. Not AEC-Q100 qualified - for automotive USB applications consider PIC18F46K50-I/PT (AEC-Q100 grade 1) instead. Lead-free reflow profile per JEDEC J-STD-020.
