PIC18LF65K40-E/PT - 64MHz 8-bit XLP MCU, 32KB Flash | Microchip
부품 번호: PIC18LF65K40-E/PT ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $4.5 | $4.50 |
| 10 | $4.05 | $40.50 |
| 100 | $3.6 | $360.00 |
| 500 | $3.2 | $1,600.00 |
| 1,000 | $2.85 | $2,850.00 |
PIC18LF65K40-E/PT 개요
An 8-bit microcontroller (MCU) is a single-chip computer based on an 8-bit data bus architecture, integrating a CPU, memory, and peripherals into one package. The PIC18LF family sits within Microchip's 8-bit PIC hierarchy: PIC18 -> PIC18F (Flash) / PIC18LF (low-voltage Flash) -> 8-bit PIC MCU -> Microcontroller -> Integrated Circuit. The 'LF' prefix denotes low-voltage operation (down to 1.8 V) suited for battery-powered and energy-harvesting applications, while XLP technology minimizes sleep current for ultra-low standby power.
Key features of the PIC18LF65K40 include Core Independent Peripherals (CWG, NCO, CLC) that offload tasks from the CPU, an IDLE/DOZE/PMD power management block, hardware CRC/SCAN for memory integrity, and Peripheral Pin Select (PPS) for flexible signal routing. The integrated ECAN module and dual EUSART enable robust wired communication for industrial networking, while the 5-bit DAC and zero-crossing detector (ZCD) simplify analog control loops without external components.
The architecture combines a RISC Harvard-bus CPU with hardware multiply and a 31-level interrupt vector table, giving deterministic real-time response. The 64-pin TQFP package offers ample I/O (up to 60 GPIO) while keeping the board footprint compact at 10x10 mm with 0.5 mm pitch. ECC Flash and RAM support data retention and resilience against soft errors for industrial control, sensor hubs, and HMI applications.
Typical applications include industrial control and automation, automotive body and sensor nodes, low-power IoT sensor nodes, HMI/keypad controllers, and consumer electronics with touch/proximity sensing. The wide 1.8 V-5.5 V supply allows direct Li-ion battery operation without external regulation, while 5 V tolerance on digital I/O simplifies interfacing to legacy 5 V logic.
When designing with this MCU, plan for an external decoupling network of 100 nF and 10 uF near VDD pins, route the analog AVSS/AVDD pair separately from digital supplies, and use the PPS feature to remap peripheral pins without re-spinning the PCB. Choose PIC18F65K40 (non-LF) only if you do not need 1.8 V operation, otherwise the LF variant preserves battery life and BOM cost in low-voltage designs.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: PIC18LF65K40-E/PT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC18LF65K40-E/PT (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Family, Package, Core, I/O Pins.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC18LF66K40-E/PT
✅ 드롭인✓ 재고 있음
$2.4 / 개
데이터시트 보기 →PIC18LF67K40-E/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC18LF65K40-I/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC18F65K40-E/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC18LF65K40-E/MR
✅ 드롭인✓ 재고 있음
$2.55 / 개
데이터시트 보기 →PIC18LF65K40-E/PT 최대 정격 & 전기적 특성
| Product Type | 8-bit Microcontroller (MCU) |
| Family | PIC18LF65K40 / PIC18LF66K40 |
| Core | PIC RISC 8-bit |
| Program Memory (Flash) | 32 KB (16K x 16) |
| RAM | 2 KB |
| EEPROM | 256 B |
| Maximum CPU Frequency | 64 MHz |
| Operating Voltage Range | 1.8 V to 5.5 V |
| I/O Pins | Up to 60 |
| ADC | 10-bit ADC2 (with Computation) |
| DAC | 5-bit DAC |
| Comparators | Yes |
| PWM / CCP / CWG | Yes (PWM, CCP, CWG peripherals) |
| Timers | Integrated Timers and Capture/Compare/PWM |
| Communication | ECAN, EUSART, SPI, I2C |
| Special Peripherals | ZCD, PPS, WWDT, SCAN/CRC, HLT, IDLE/DOZE/PMD |
| 패키지 | 64-pin TQFP (PT), 10x10 mm, 0.5 mm pitch |
| 실장 유형 | Surface Mount |
| 동작 온도 | -40 C to +125 C (E = extended) |
| RoHS 상태 | Compliant |
PIC18LF65K40-E/PT 핀 구성
| 핀 1 | MCLR — Master Clear (Reset) input, active-low |
| 핀 2 | RA0 — PORTA0 / analog input |
| 핀 3 | RA1 — PORTA1 / analog input |
| 핀 4 | RA2 — PORTA2 / analog input |
| 핀 5 | RA3 — PORTA3 / analog input |
| 핀 6 | RA4 — PORTA4 / analog input |
| 핀 7 | RA5 — PORTA5 / analog input |
| 핀 8 | RA6 — PORTA6 / analog input |
| 핀 9 | RA7 — PORTA7 / analog input |
| 핀 10 | VSS — Ground |
| 핀 11 | VDD — Positive supply |
| 핀 12 | RB0 — PORTB0 / IOC |
| 핀 13 | RB1 — PORTB1 / IOC |
| 핀 14 | RB2 — PORTB2 / IOC |
| 핀 15 | RB3 — PORTB3 / IOC |
| 핀 16 | RB4 — PORTB4 / IOC |
| 핀 17 | RB5 — PORTB5 / IOC / PWM |
| 핀 18 | RB6 — PORTB6 / IOC / PGC |
| 핀 19 | RB7 — PORTB7 / IOC / PGD |
| 핀 20 | VSS — Ground |
| 핀 21 | VDD — Positive supply |
| 핀 22 | RC0 — PORTC0 |
| 핀 23 | RC1 — PORTC1 |
| 핀 24 | RC2 — PORTC2 |
| 핀 25 | RC3 — PORTC3 |
| 핀 26 | RC4 — PORTC4 |
| 핀 27 | RC5 — PORTC5 |
| 핀 28 | RC6 — PORTC6 / TX |
| 핀 29 | RC7 — PORTC7 / RX |
| 핀 30 | VSS — Ground |
| 핀 31 | VDD — Positive supply |
| 핀 32 | RD0 — PORTD0 |
| 핀 33 | RD1 — PORTD1 |
| 핀 34 | RD2 — PORTD2 |
| 핀 35 | RD3 — PORTD3 |
| 핀 36 | RD4 — PORTD4 |
| 핀 37 | RD5 — PORTD5 / PWM |
| 핀 38 | RD6 — PORTD6 / PWM |
| 핀 39 | RD7 — PORTD7 / PWM |
| 핀 40 | VSS — Ground |
| 핀 41 | VDD — Positive supply |
| 핀 42 | RE0 — PORTE0 / analog |
| 핀 43 | RE1 — PORTE1 / analog |
| 핀 44 | RE2 — PORTE2 / analog |
| 핀 45 | RE3 — PORTE3 / analog |
| 핀 46 | AVSS — Analog ground |
| 핀 47 | AVDD — Analog positive supply |
| 핀 48 | OSC1 — Crystal/oscillator input |
| 핀 49 | OSC2 — Crystal/oscillator output |
| 핀 50 | RF0 — PORTF0 |
| 핀 51 | RF1 — PORTF1 |
| 핀 52 | RF2 — PORTF2 |
| 핀 53 | RF3 — PORTF3 |
| 핀 54 | RF4 — PORTF4 |
| 핀 55 | RF5 — PORTF5 |
| 핀 56 | RF6 — PORTF6 |
| 핀 57 | RF7 — PORTF7 |
| 핀 58 | RG0 — PORTG0 |
| 핀 59 | RG1 — PORTG1 |
| 핀 60 | RG2 — PORTG2 |
| 핀 61 | RG3 — PORTG3 |
| 핀 62 | RG4 — PORTG4 |
| 핀 63 | VSS — Ground |
| 핀 64 | VDD — Positive supply |
일반적인 애플리케이션
PIC18LF65K40-E/PT 적합 용도: 6 애플리케이션s: Industrial Sensor Node / 4-20 mA Transmitter, Automotive Body Control Module, Low-Power IoT / Battery Sensor Hub, HMI / Keypad / Small Touch Controller, Consumer Appliance Control Board, Portable / Wearable Medical Devices.
Industrial Sensor Node / 4-20 mA Transmitter
The PIC18LF65K40-E/PT's 1.8 V-5.5 V supply range, XLP sleep current under 1 uA, and integrated 10-bit ADC2 with Computation enable direct battery-powered sensor conditioning for industrial 4-20 mA transmitters and process-control nodes. The ECAN module supports DeviceNet and CANopen protocols commonly used in factory automation, while the dual EUSART and SPI/I2C ports interface to digital sensors and HMI displays. At full 64 MHz the 16 MIPS throughput handles filtering, linearization, and HART-style modulation on-chip. PPS remaps peripheral pins without board rework.
추천
Automotive Body Control Module
The PIC18LF65K40-E/PT's integrated ECAN and wide 1.8 V-5.5 V supply tolerance with -40 C to +125 C extended temperature grade make it suitable for automotive body and convenience modules (window lifters, mirror controllers, HVAC flap actuators). The PIC18LF65K40 family supports CAN 2.0B active, removing the need for a separate CAN controller IC. The 5-bit DAC drives analog actuator setpoints, while PWM/CWG generates motor control signals. PPS and Core Independent Peripherals offload timing-critical tasks from the CPU, freeing MIPS for diagnostics and OBD-II signaling.
추천
Low-Power IoT / Battery Sensor Hub
XLP technology and 1.8 V minimum supply give the PIC18LF65K40-E/PT ultra-low sleep current (under 1 uA typical), enabling years of operation from a single CR2032 coin cell or two AA alkaline cells. The MCU wakes on ADC2 threshold triggers, ZCD events, or interrupt-on-change pins, samples sensors via SPI/I2C, transmits over EUSART or ECAN, and returns to sleep without CPU intervention. Hardware CRC/SCAN protects Flash integrity while in the field. ZCD enables zero-crossing power metering for AC mains-powered IoT energy monitors with no external detection circuitry.
추천
HMI / Keypad / Small Touch Controller
With up to 60 GPIO and Peripheral Pin Select, the PIC18LF65K40-E/PT can directly scan 8x8 matrix keypads, drive character or graphic LCDs, and read capacitive-touch sensors via the integrated comparators and PWM/CWG. The 5-bit DAC generates contrast voltages for legacy LCDs without a charge pump. ADC2 with Computation scans multiple touch pads in software while the CWG outputs the excitation waveform, eliminating dedicated touch ICs. PPS remaps touch channels to spare pins for layout flexibility in space-constrained HMI front panels.
추천
Consumer Appliance Control Board
White goods and small appliances benefit from the PIC18LF65K40-E/PT's integrated motor-control peripherals (PWM/CCP/CWG), ZCD for AC zero-crossing detection, and 5-bit DAC for analog trim. The 64-pin TQFP exposes enough GPIO to drive triac-based heater control, relays, and user displays while the ECAN interface supports appliance network buses. XLP enables standby power below 100 mW to meet global energy regulations, and the extended -40 C to +125 C temperature grade handles the thermal environment behind a refrigerator compressor or oven fascia.
추천
Portable / Wearable Medical Devices
For portable medical peripherals (pulse-oximeter probes, handheld spirometers, blood-pressure monitors) the PIC18LF65K40-E/PT's 1.8 V operation, XLP sleep, and integrated ADC2/DAC/Comparators minimize external components and battery count. The ECAN or EUSART link to a host controller while the SPI/I2C ports read sensor front-ends. Hardware CRC and SCAN protect Flash against soft errors in long-term deployments. The wide 1.8 V-5.5 V supply lets designers reuse a single-cell Li-ion or two AAA cells without a boost converter, shrinking the bill of materials.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC18LF65K40-E/PT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC18LF66K40-E/PT | PIC18LF67K40-E/PT | PIC18LF65K40-I/PT | PIC18F65K40-E/PT | PIC18LF65K40-E/MR |
|---|---|---|---|---|---|---|
| Package | 64-pin TQFP (PT), 10x10 mm | 64-pin TQFP (PT), 10x10 mm - same | 64-pin TQFP (PT), 10x10 mm - same | 64-pin TQFP (PT), 10x10 mm - same | 64-pin TQFP (PT), 10x10 mm - same | 64-pin TQFP (PT), 10x10 mm - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 32 KB | 64 KB | 128 KB | 32 KB | 32 KB | 32 KB |
| RAM | 2 KB | 4 KB | 8 KB | 2 KB | 2 KB | 2 KB |
| EEPROM | 256 B | 256 B | 256 B | 256 B | 256 B | 256 B |
| Operating Voltage Range | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 2.3 V to 5.5 V | 1.8 V to 5.5 V |
| Operating Temperature | -40 C to +125 C (E = extended) | -40 C to +125 C | -40 C to +125 C | -40 C to +85 C (industrial) | -40 C to +125 C | -40 C to +125 C |
| Max CPU Frequency | 64 MHz (16 MIPS) | 64 MHz (16 MIPS) | 64 MHz (16 MIPS) | 64 MHz (16 MIPS) | 64 MHz (16 MIPS) | 64 MHz (16 MIPS) |
주요 차별점
- Lowest-Voltage Operation in the Family (vs PIC18F65K40-E/PT)
- Extended Temperature Grade (-40C to +125C) (vs PIC18LF65K40-I/PT)
- Same 64-pin TQFP Pinout Across the Family (vs PIC18LF66K40-E/PT)
설계 노트
Place 100 nF ceramic decoupling capacitors within 3 mm of every VDD pin and a single 10 uF bulk capacitor on the supply rail. For PIC18LF65K40-E/PT designs that use ADC2, add a separate 100 nF + 10 uF pair on AVDD to keep analog and digital noise isolated. The wide 1.8 V-5.5 V input range means you can power the part directly from a single-cell Li-ion battery (3.0 V-4.2 V) or two AA cells without an LDO, saving BOM cost in low-power designs.
Route the MCLR pin to a dedicated reset button with a 10 kohm pull-up to VDD; adding a 100 nF capacitor from MCLR to VSS provides noise immunity in noisy industrial environments. For in-circuit serial programming (ICSP), dedicate pins RB6 (PGC) and RB7 (PGD) - do not share them with high-impedance analog signals that could disturb programming. The 64-pin TQFP (PT) at 0.5 mm pitch requires fine-pitch PCB layout: use 0.2 mm traces between pads and 0.5 mm via-in-pad for reliable manufacturing.
Do not assume the PIC18F65K40 and PIC18LF65K40 are interchangeable - the F variant requires VIN >= 2.3 V and will brown-out below that, while the LF variant operates to 1.8 V. Estimated: at 3.3 V supply with 64 MHz CPU, core current is around 10 mA but XLP sleep drops to under 1 uA; verify that peripheral pins are configured as digital (ANSELx cleared) before using them as GPIO, otherwise the input buffer is disabled. Use the PPS Unlock sequence before remapping peripheral outputs to avoid an inadvertent lock condition.
규정 준수 정보
RoHS compliant per Microchip product page. Lead-free matte-tin finish. AEC-Q100 not qualified (this is a general-purpose MCU; automotive customers should evaluate the Automotive Portfolio for Q-graded variants).
