SN74AHC9541-Q1 - AEC-Q100 Octal Buffer, Schmitt | TI
부품 번호: SN74AHC9541-Q1 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
SN74AHC9541-Q1 개요
An octal buffer is a digital logic IC providing eight independent buffering channels that isolate, amplify, and restore digital signals. Buffers sit within the standard logic family hierarchy (CMOS logic > buffers/line drivers > single gates), preventing loading effects on driving circuits and regenerating weak or degraded signals across PCB traces, cables, and backplanes. Schmitt-trigger inputs add hysteresis, converting slow or noisy input edges into clean, fast output transitions.
Key features include the wide 2V to 5.5V operating range compatible with 3.3V and 5V logic systems, dual active-low output enables (OE1 and OE2) that must both be low to activate all eight outputs, and AEC-Q100 automotive qualification. According to the TI datasheet, the device drives loads with total capacitance up to 50pF while meeting all datasheet specifications; larger loads may be applied but exceeding 50pF is not recommended.
Fabricated in AHC-series CMOS technology, the device delivers low static power consumption, high speed, and balanced drive. The wettable-flank QFN package improves wetting of the package edge during soldering and enables automated optical inspection (AOI), a key automotive quality requirement.
Typical applications include automotive body control modules, infotainment systems, ADAS signal buffering, and industrial interfaces where slow or noisy signals must be conditioned or held during controller reset.
Design tip: keep per-output capacitive loading at or below 50pF, place 0.1uF decoupling capacitors close to VCC, and tie unused inputs to VCC or GND - never leave CMOS inputs floating.
드롭인 대체품: SN74AHC9541-Q1 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
SN74AHCT9541-Q1
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
SN74AHC9541
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
SN74AHC9541-Q1 최대 정격 & 전기적 특성
| 기능 | Octal buffer / line driver, non-inverting |
| 채널 수 | 8 bits per element, 1 element |
| Supply Voltage Range | 2 V to 5.5 V |
| Input Type | Schmitt-trigger |
| 출력 유형 | 3-state |
| Output Enable | OE1 and OE2, active low (both must be low) |
| Max Capacitive Load (specified) | 50 pF |
| 동작 온도 | -40C to +125C |
| Qualification | AEC-Q100 automotive |
| 패키지 | 20-VSSOP (DGS), wettable-flank QFN option |
| 실장 유형 | Surface Mount |
| Technology | AHC-series CMOS |
| Polarity | Non-inverting |
| Package Marking | HA9541Q |
| RoHS 상태 | Compliant |
| Typical Applications | Automotive digital signal buffering and conditioning |
SN74AHC9541-Q1 핀 구성
| 핀 1 | OE1 — Output enable 1 (active low) |
| 핀 2 | 1A1 — Channel 1 input (Schmitt-trigger) |
| 핀 3 | 2A1 — Channel 2 input (Schmitt-trigger) |
| 핀 4 | 3A1 — Channel 3 input (Schmitt-trigger) |
| 핀 5 | 4A1 — Channel 4 input (Schmitt-trigger) |
| 핀 6 | GND — Ground |
| 핀 7 | 5A1 — Channel 5 input (Schmitt-trigger) |
| 핀 8 | 6A1 — Channel 6 input (Schmitt-trigger) |
| 핀 9 | 7A1 — Channel 7 input (Schmitt-trigger) |
| 핀 10 | 8A1 — Channel 8 input (Schmitt-trigger) |
| 핀 11 | OE2 — Output enable 2 (active low) |
| 핀 12 | 1Y — Channel 1 3-state output |
| 핀 13 | 2Y — Channel 2 3-state output |
| 핀 14 | 3Y — Channel 3 3-state output |
| 핀 15 | 4Y — Channel 4 3-state output |
| 핀 16 | VCC — Power supply, 2V to 5.5V |
| 핀 17 | 5Y — Channel 5 3-state output |
| 핀 18 | 6Y — Channel 6 3-state output |
| 핀 19 | 7Y — Channel 7 3-state output |
| 핀 20 | 8Y — Channel 8 3-state output |
일반적인 애플리케이션
SN74AHC9541-Q1 적합 용도: 6 애플리케이션s: Automotive Body Control Modules, ADAS Signal Buffering, Automotive Infotainment Systems, Signal Holding During Controller Reset, Industrial PLC I/O Buffering, Automotive Gateways and Networking Modules.
Automotive Body Control Modules
In body control modules, the SN74AHC9541-Q1 buffers switch, relay-control, and sensor-status lines where slow, noisy edges from electromechanical contacts must be squared up. Schmitt-trigger inputs regenerate degraded transitions, while the 2V to 5.5V range supports mixed 3.3V/5V modules. AEC-Q100 qualification and the wettable-flank VSSOP-20 package meet automotive quality and AOI inspection requirements; keep each output load at or below 50pF to preserve specified timing.
추천
ADAS Signal Buffering
The SN74AHC9541-Q1 buffers digital sensor-status and enable lines in ADAS modules, where the Schmitt-trigger inputs reject noise picked up on long harness interconnects. The dual active-low enables (OE1 and OE2) allow both a microcontroller and a safety monitor to control bus connection, supporting fail-safe output disable. AEC-Q100 qualification across -40C to +125C suits underhood and zonal module environments; the 3-state outputs isolate sensor buses during diagnostics.
추천
Automotive Infotainment Systems
In infotainment head units, the SN74AHC9541-Q1 buffers I2S enable lines, button-status inputs, and panel-backlight control signals. Schmitt-trigger inputs clean up noisy edges from switches and long board traces, and the 2V to 5.5V supply bridges 3.3V SoC rails and 5V peripheral rails. The 3-state outputs let the display or amplifier bus be shared during reset, and AEC-Q100 qualification covers the cabin-to-temperature-grade range demanded by tier-1 platforms.
추천
Signal Holding During Controller Reset
TI highlights the SN74AHC9541-Q1 for holding a signal during controller reset: while the microcontroller pins are high-impedance or undefined, the dual OE1/OE2 enables can be strapped low by RC or supervisor logic to keep the last driven state latched on the bus, or high to float it safely. Schmitt inputs ensure the held logic state is not corrupted by supply-ramp noise, and the wide 2V to 5.5V operation tracks the rail during power sequencing.
추천
Industrial PLC I/O Buffering
Industrial programmable-logic-controller I/O cards use the SN74AHC9541-Q1 to buffer field-status signals into the controller. Schmitt-trigger inputs condition slow edges from optocouplers, relays, and long cable runs, regenerating them into fast CMOS edges; the 3-state outputs tri-state the card bus during module hot-swap or backplane arbitration. Although qualified for automotive, the -40C to +125C rating and low static CMOS power equally benefit rugged industrial installations.
추천
Automotive Gateways and Networking Modules
In gateway ECUs, the SN74AHC9541-Q1 buffers wake-up, status, and mux-select lines between transceivers and the host MCU. The Schmitt-trigger inputs restore edges from long PCB runs near noisy CAN/LIN transceivers, while OE1/OE2 allow the SBC or safety MCU to disconnect status buses during fault handling. The wettable-flank VSSOP-20 package supports AOI on high-volume SMT lines, and AEC-Q100 qualification covers the full automotive ambient range of -40C to +125C.
추천
추천 제품 요약
엔지니어링 참조 데이터: SN74AHC9541-Q1 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | SN74AHCT9541-Q1 | SN74AHCT7541-Q1 | SN74HCS541QPWRQ1 |
|---|---|---|---|---|
| Package | 20-VSSOP (DGS), wettable-flank option | 20-VSSOP / TSSOP-20 | 20-TSSOP / 20-SOIC | 20-TSSOP (PW) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Function | Octal non-inverting buffer, 3-state | Octal non-inverting buffer, 3-state | Octal inverting buffer, 3-state | Octal non-inverting buffer, 3-state |
| Schmitt-Trigger Inputs | Yes | Yes (TTL thresholds) | Yes | Yes |
| Supply Voltage | 2 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 2 V to 5.5 V |
| AEC-Q100 | Qualified | Qualified | Qualified | Qualified |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C |
주요 차별점
- AEC-Q100 automotive qualification (vs SN74AHC9541 (standard grade))
- Wide 2V to 5.5V supply range (vs SN74AHCT9541-Q1)
- Dual redundant output enables (vs SN74HCS541QPWRQ1)
설계 노트
Exploit the Schmitt-trigger inputs: they are designed to convert slow, noisy edges from switches, sensors, and long interconnects into clean transitions. However, keep each output load at or below 50pF; per the TI datasheet, larger capacitive loads can be driven but propagation delay and transition times degrade beyond specified limits, affecting timing margins in shared automotive buses.
Place a 0.1uF ceramic decoupling capacitor within a few millimeters of the VCC pin, with an additional bulk capacitor per group of devices. The wettable-flank QFN/VSSOP package option exists specifically so AOI can verify solder fillets on the package edge - enable the wettable-flank variant for automotive builds and adjust stencil aperture design for the exposed thermal performance of the small VSSOP-20 body.
Never leave CMOS inputs floating: tie unused A inputs to VCC or GND, otherwise floating Schmitt inputs can oscillate near the threshold region and increase supply current. Remember both OE1 and OE2 must be pulled low to enable outputs - a single high OE pin tri-states all eight outputs, which is a common bring-up issue if one enable is left unterminated.
규정 준수 정보
AEC-Q100 qualified per TI product page. RoHS compliance per TI standard offering; verify specific ordering suffix compliance certificate on ti.com.
