onsemi

SN74LS641H - 8-Bit Open-Collector Bus Transceiver | onsemi

부품 번호: SN74LS641H ✗ 단종
MOQ: 1 |

SN74LS641H 개요

onsemi SN74LS641H is an 8-bit bipolar bus transceiver with open-collector outputs, supplied under the SN74LS logic family. It provides a practical interface between a digital bus and externally driven data lines, supporting legacy TTL-style equipment, control systems, test fixtures, and industrial data-acquisition designs. The device belongs to the buffer, driver, and transceiver hierarchy within digital logic ICs.

A bus transceiver combines two directed data paths in one package. Data can move from the bus into the receiving logic, while the driver section presents the opposite signal direction to the external bus. Its open-collector outputs are important because the output stage can provide a wired-AND function when an appropriate pull-up is present. This characteristic is useful in systems where several devices share a signal line or where bus fault handling requires a passive pull-down behavior.

The SN74LS641H is associated with the SN74LS641 octal bus-transceiver family. The SN74LS641 family is identified as an octal device with open-collector outputs. The H suffix distinguishes the onsemi ordering variant from the base family name, while its exact package, temperature grade, lifecycle status, and full electrical limits should be selected from the manufacturer’s order information for the complete MPN.

As a member of the low-power Schottky TTL family, the device is associated with 74LS-compatible logic systems. Its open-collector interface can support bus-oriented signal conditioning where conventional totem-pole outputs are unsuitable. Designers should nevertheless verify propagation delay, sink current, output rise time, input thresholds, and supply-voltage tolerances against the exact SN74LS641H datasheet before using it as a timing-critical component.

Typical uses include interfacing processor buses to open-collector peripherals, communicating with legacy test equipment, isolating logical signals through a bus-driver stage, and building wired-control networks with external pull-up resistors. In each case, the external pull-up value determines the rise time, bus speed, and current drawn while the output transistor is off. The manufacturer application guidance should govern resistor selection and logic-family interfacing.

A key design consideration is the difference between a logic-compatible receiver input and an open-collector driver output. The input side may drive from another TTL-family device, while the output side requires suitable pull-up components and must not exceed the published sink-current and voltage limits. Treat the bus as a wired node, calculate its worst-case loading, and verify contention behavior during power-up, reset, and output disable.

This product page combines the confirmed SN74LS641H identity with practical guidance for evaluating bus direction, pull-up requirements, package-dependent PCB compatibility, legacy-logic timing, and procurement alternatives. Exact dimensions, pin assignments, and electrical limits remain tied to the ordered package suffix, while the manufacturer datasheet and product page provide the controlling information for design release.

드롭인 대체품: SN74LS641H — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 제품에는 사용 가능한 드롭인 대체품이 없습니다.

대체품 요청

SN74LS641H 최대 정격 & 전기적 특성

Product Type Octal bus transceiver
Number of Data Bits 8 bits
Output Characteristic Open collector
Logic Family SN74LS low-power Schottky TTL
RoHS 상태 Compliant
Manufacturer onsemi

SN74LS641H standard 핀 구성 가이드

SN74LS641H(standard 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.

SN74LS641H의 standard 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: SN74LS641H.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

SN74LS641H 적합 용도: 6 애플리케이션s: Legacy Processor Bus Interface, Industrial Control Signal Bus, Legacy Test Equipment Interface, Wired-AND Alarm System, Data-Acquisition Backplane Interface, Data-Acquisition Backplane Interface.

🖥️

Legacy Processor Bus Interface

The SN74LS641H fits legacy processor and peripheral systems that require an 8-bit open-collector bus driver rather than a conventional push-pull transceiver. Its SN74LS-family interface characteristics support systems built around 74LS-compatible logic, while the open-collector outputs allow the bus to be pulled high externally. The design must include adequate pull-up resistors, define every direction-control state, and prevent two enabled drivers from driving opposite levels. Confirm propagation delay, input thresholds, and output sink current against the exact onsemi documentation before using the device in a timing-critical processor interface.

🏭

Industrial Control Signal Bus

The SN74LS641H can bridge control logic and open-collector field signals in an industrial control assembly. Eight parallel channels provide useful density where a controller must monitor and drive several related lines, and the open-collector output stage supports wired-AND behavior with suitable pull-up components. Engineer the system for fault-safe bus contention, controlled reset states, and adequate isolation from motor or relay transients. The external pull-up resistance should be selected from the required switching speed, total bus capacitance, and published sink-current limit rather than chosen solely by logic family.

🔧

Legacy Test Equipment Interface

The SN74LS641H is appropriate for test fixtures and legacy measurement equipment that exchange multiple digital lines with open-collector-compatible peripherals. Its 8-bit channel count allows one package to handle a parallel control or status bus while keeping the interface electrically consistent with 74LS-family circuitry. The receiving path can be used for logic sensing, while the driver path must use external pull-ups. Validate timing margins across cable length, fixture capacitance, and probe loading, and provide a defined state for the direction and enable controls during fixture power-up.

⚡

Wired-AND Alarm System

The open-collector outputs of the SN74LS641H make the device relevant to alarm, fault, and shutdown lines in which multiple independently powered nodes can report a fault by pulling a shared line low. Eight channels support multiple monitor points, while external pull-ups restore the inactive state to a logic high. Robust implementation requires isolation or careful input design for each node, because a grounded or incorrectly powered participant can clamp the shared line. Verify output voltage, sink current, and behavior during reset against the exact SN74LS641H specifications.

📡

Data-Acquisition Backplane Interface

The SN74LS641H can interface a data-acquisition controller with backplane logic that uses open-collector signaling. Its eight parallel channels provide a practical match for module-select, interrupt, acknowledgment, or distributed control lines rather than high-speed data paths. The open-collector node should be treated as a shared electrical resource: use one defined pull-up strategy, keep pull-up current within the driver limit, and analyze the slowest configured edge when multiple modules add capacitance. Direction control must remain stable throughout each transfer to avoid unintended bus contention.

📊

Data-Acquisition Backplane Interface

The SN74LS641H can support older data-acquisition backplanes that expose control, interrupt, or module-acknowledgment lines through open-collector wiring. Eight channels can consolidate parallel handshaking functions, provided the bus is operated within the device’s published voltage and timing limits. Select pull-up values from the slowest required bus edge and the total installed capacitance, then confirm that every attached module can safely pull the node low. Define safe direction states during power-up and reset, since uncontrolled contention can produce excess current or misleading fault indications.

What is the SN74LS641H?
The onsemi SN74LS641H is an 8-bit bus transceiver with open-collector outputs in the SN74LS low-power Schottky TTL logic family. Texas Instruments describes the corresponding SN74LS641 family as octal bus transceivers with open-collector outputs. The device is intended for bidirectional or multi-source bus-interface designs where wired-AND behavior and pull-up resistors are appropriate.
What is the operating voltage of SN74LS641H?
The exact SN74LS641H supply-voltage limits must be confirmed in the manufacturer datasheet for the ordered package and grade. The SN74LS family is associated with 5 V TTL-class operation, but the complete MPN data must govern the design because onsemi may offer multiple package, temperature, and lifecycle configurations. Use the specified input and output voltage limits when calculating absolute maximum stresses.
Where can I download the SN74LS641H datasheet PDF?
Use the official SN74LS641 product page at the link on this page to locate the family documentation and ordering information. The exact SN74LS641H datasheet should be selected by matching the complete onsemi suffix, package, and grade. Texas Instruments also provides an official SN74LS641 family page, which is useful for understanding the octal open-collector transceiver function.
Where is the SN74LS641H pinout?
The pinout for the exact SN74LS641H package must be taken from the pin-description table in the manufacturer datasheet. The H suffix is not sufficient by itself to determine the physical pin mapping because package dimensions and ordering codes can vary. Before laying out a PCB, verify every data, enable, direction-control, supply, and ground connection against the exact package drawing.
Can SN74LS641H interface with 74LS logic?
The SN74LS641H is designed for compatibility with 74LS-family bus interfaces, but signal compatibility must be checked at the system level. Confirm input thresholds, output sink current, propagation delay, and supply levels for every connected device. Open-collector outputs also require pull-up resistors and must not be used where a totem-pole output is assumed.
What pull-up resistor should be used with SN74LS641H?
Select the open-collector pull-up resistor from the required bus rise time, bus capacitance, receiver input current, and maximum output sink current. A smaller resistance produces a faster rising edge but increases low-state current, while a larger resistance reduces current and slows the edge. Confirm both limits against the exact SN74LS641H electrical characteristics before releasing the design.
Is SN74LS641H suitable for bidirectional bus communication?
The SN74LS641H can suit bidirectional bus-interface work when its direction-control and output-enable functions are managed correctly. Its open-collector outputs support wired-bus behavior, but every device sharing the node must be disabled during contention. Design the logic so normal operating states cannot place two output drivers into opposing low states.
SN74LS641H vs SN74LS641H alternatives - which one is best for a legacy bus?
The best choice is the device whose exact package, supply range, direction-control behavior, output timing, and lifecycle status match the legacy bus. SN74LS641H is appropriate when the original design used the onsemi H variant and its open-collector interface. The same functional function in another package or with different enable logic may require PCB changes and therefore is not a true drop-in replacement.
When should I choose SN74LS641H over a conventional 74HC bus transceiver?
Choose SN74LS641H when the interface specifically requires an open-collector driver and wired-AND bus behavior. A 74HC transceiver may use push-pull outputs, different supply-voltage requirements, and different input thresholds, so it cannot automatically replace the SN74LS641H. Select the modern device only after confirming voltage, timing, contention, and package compatibility.
What can replace SN74LS641H?
A genuine replacement must match the exact package and be pin-to-pin compatible while preserving the supply voltage, direction-control logic, enable functions, and open-collector output behavior. The SN74LS641H is a legacy onsemi ordering variant, and the available cross-reference material does not identify five distinct same-package drop-in parts. Request a controlled cross-reference or schematic review before substituting a device.
Is SN74LS641H the same as the TI SN74LS641?
The devices belong to the same SN74LS641 octal open-collector transceiver family at the functional level, but they are not automatically identical drop-in parts. The onsemi SN74LS641H suffix identifies a particular manufacturer orderable configuration, while the TI SN74LS641 designation can resolve to different packages and grades. Check the pinout, package, electrical limits, and lifecycle status for each exact MPN.
What is the best cross-brand equivalent for SN74LS641H?
There is no confirmed cross-brand drop-in equivalent identified by the exact package and electrical behavior of SN74LS641H in the available cross-reference results. A functional 74LS-series octal transceiver is not enough because package, enable polarity, direction control, and output-stage details may differ. Use the Request a Quote form for sourcing support, and require manufacturer confirmation for any proposed substitution.
Is SN74LS641H in stock and what is its lead time?
Current stock and lead time for SN74LS641H must be confirmed through the Request a Quote form on this page. The part is a legacy 74LS-family transceiver, so supply status can depend on the exact onsemi package and grade. Provide the required quantity, target date, and approved manufacturer list when requesting a quotation and schedule confirmation.
Where can I buy SN74LS641H online?
Use the Request a Quote form on this page to request SN74LS641H availability, price, and lead time for your exact quantity. The order should identify the onsemi manufacturer and the complete SN74LS641H suffix to avoid package or grade mismatches. A direct quote also allows the requested packaging and delivery conditions to be confirmed before procurement.
What are the key specifications of SN74LS641H that engineers should know?
The confirmed headline characteristics are an 8-bit octal bus-transceiver function, open-collector outputs, and membership in the SN74LS low-power Schottky TTL family. Exact supply voltage, timing, output-current, temperature-range, and package limits are controlled by the onsemi documentation for the complete ordering suffix. Those parameters determine bus speed, pull-up selection, thermal margin, and PCB compatibility.

엔지니어링 참조 데이터: SN74LS641H — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose SN74LS641H when maintaining or redesigning a system that specifically requires an onsemi 8-bit SN74LS-family transceiver with open-collector outputs. Its useful distinction is not merely octal buffering, but the ability to support wired-bus behavior with external pull-up resistors. This makes it suitable for legacy control, test, and data-acquisition interfaces where push-pull drivers would create undesirable contention. Do not select it solely by the SN74LS641 function number: confirm the exact package, pin assignment, supply limits, timing, temperature grade, and lifecycle status. A base SN74LS641 from another manufacturer may have the same broad function but still require PCB or logic changes. For any proposed cross-brand substitute, demand a manufacturer-confirmed pin-to-pin cross-reference and verify the output stage, enable polarity, and direction-control behavior before design release.

대체품과의 비교

파라미터 이 제품
Brand onsemi
Product Type Octal bus transceiver
Number of Data Bits 8 bits
Output Characteristic Open collector
Logic Family SN74LS low-power Schottky TTL

설계 노트

Do not assume that every octal 74LS transceiver is a drop-in replacement. Check the complete pin map, direction-control polarity, enable function, supply range, and open-collector output arrangement. SN74LS641H is an onsemi ordering variant, and the H suffix does not establish compatibility by itself. For an existing PCB, compare the exact package drawing and each numbered connection before approving a substitute.

Calculate the pull-up resistor from the required rising-edge time, total bus capacitance, receiver leakage current, and maximum low-level sink current. A stronger pull-up lowers rise time but increases current when the driver is active. Evaluate the slowest edge when multiple nodes, connectors, and test fixtures are connected, and ensure the resulting transition remains compatible with the receiving logic’s threshold and timing requirements.

Define direction-control and enable states during reset, power-up, power-down, and fault recovery. Multiple open-collector outputs can safely share a node, but this does not protect against unrelated contention or incorrect sequencing. Use pull-up or pull-down resistors where a defined state is required, and verify that the external bus never exceeds the device’s absolute maximum output and input voltage ratings.

규정 준수 정보

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The SN74LS641H listing identifies the part as RoHS compliant. Other compliance declarations are not established by the cited product information.

관련 검색

SN74LS641H datasheet SN74LS641H datasheet pdf SN74LS641H pinout SN74LS641H equivalent SN74LS641H replacement SN74LS641H cross reference SN74LS641H price SN74LS641H stock onsemi SN74LS641H SN74LS641H open collector transceiver SN74LS641H SOIC pinout SN74LS641 application circuit

관련 부품 & 용어

onsemi SN74LS641H SN74LS641 Texas Instruments 8-bit bus transceiver octal bus transceiver buffer driver transceiver open-collector output SN74LS low-power Schottky TTL digital logic IC bipolar logic wired-AND bus pull-up resistor bidirectional bus direction control legacy industrial control data-acquisition interface logic threshold propagation delay sink current surface-mount logic
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기