Produk (46,000+)

SN74LS629D - Dual 20MHz VCO IC | Texas Instruments
SN74LS629D

SN74LS629D - Dual 20MHz VCO IC | Texas Instruments

Texas Instruments SN74LS629D is a dual voltage-controlled oscillator, or VCO, integrated circuit with a maximum operating frequency of 20 MHz in a 16-pin small-outline integrated-circuit package. The SN74LS629 family provides two oscillator channels on one device, making it useful when a system requires two independently adjustable timing signals without allocating separate oscillator packages. Its 16-SOIC package supports conventional surface-mount assembly and a compact PCB footprint. A voltage-controlled oscillator is a clock-generation device whose output frequency is adjusted by an external control voltage. In the broader semiconductor hierarchy, a VCO belongs to the clock and timing IC family, alongside programmable timers and fixed-function oscillator circuits. By translating a varying voltage into a changing clock frequency, this type of IC supports frequency modulation, tone generation, sweep generation, phase measurement, and closed-loop frequency-control systems. The SN74LS629D is identified as a dual VCO with a 20 MHz upper frequency. Two VCO sections in one package reduce component count and simplify board planning when both channels can share the same supply and ground architecture. The device is offered in the SN74LS629 series, whose ordering options include different package or delivery configurations. Its standard logic-family implementation is suited to conventional 5 V digital systems. The SN74LS629 architecture separates frequency control from the oscillator output. External timing components determine each oscillator's operating characteristics, while the control voltage changes the instantaneous output frequency. Designers must account for component tolerances, control-voltage range, maximum operating frequency, output loading, and supply decoupling when calculating tuning range and frequency accuracy. The manufacturer's pin-description table and recommended operating conditions should govern final component selection and circuit values. Typical applications include dual-channel swept-signal sources, audio tone generators, modulation circuits, instrumentation test signals, frequency-discriminator demonstrations, and laboratory timing systems. Two oscillators can also generate a reference and a controlled test signal, or provide two phase-related waveforms for clock-data or feedback experiments. Where a fixed or digitally programmable clock is sufficient, a conventional oscillator or timer may be simpler; the SN74LS629D is most appropriate when continuous voltage-based frequency adjustment is valuable. For robust PCB implementation, place each oscillator's frequency-setting components close to the associated IC pins and keep control-voltage traces away from high-current switching nodes. Provide a low-impedance ground plane, decouple the supply near the device, and validate the control-voltage range with the external network. Confirm output rise and fall times at the intended load because frequency behavior and usable bandwidth can depend on the surrounding circuit. This product page combines the Texas Instruments device identity, dual-VCO function, 20 MHz frequency capability, 16-SOIC packaging, sourcing information, comparison points, and practical implementation guidance. It is intended to help engineers identify the correct logic-family oscillator and plan a layout that preserves tuning accuracy, timing stability, and signal integrity.

RFC Hubungi kami
SN74LS629N - Dual 20 MHz VCO | Texas Instruments
SN74LS629N

SN74LS629N - Dual 20 MHz VCO | Texas Instruments

Texas Instruments SN74LS629N is a dual voltage-controlled oscillator in a 16-pin PDIP package. Each of its two independently controlled oscillator sections provides a maximum operating frequency of 20 MHz, while the input control voltage varies the operating frequency according to the device transfer characteristics. The SN74LS629N is designed for frequency generation, frequency modulation, tone generation, sweep generation, phase-related signal processing, and clocking applications where an adjustable clock or carrier is required. A voltage-controlled oscillator, or VCO, is a timing and frequency-generation circuit whose output frequency is controlled by an externally applied voltage. It belongs to the oscillator and clock-and-timing IC hierarchy, where it combines a stable internal oscillator with a voltage-to-frequency conversion function. The dual architecture provides two oscillator channels in one package, reducing component count and board area when a system requires two related but independently adjustable timing signals. The primary electrical characteristics of the SN74LS629N include two voltage-controlled oscillator sections, a maximum frequency of 20 MHz, and a 16-pin PDIP package rated for a 0°C to 70°C operating temperature range. The N package suffix identifies the standard through-hole PDIP configuration. The device is associated with the SN74LS629 family, which is categorized by Texas Instruments as a programmable timer and oscillator product within the 74LS logic family. The dual VCO structure makes the SN74LS629N useful when two frequencies must vary without using two separate oscillator packages. Each oscillator can be driven by its own control voltage, allowing one channel to act as a reference while the other performs modulation or sweep generation. Designers should account for the control-voltage range, transfer gain, output drive, and load capacitance listed in the manufacturer datasheet when setting the operating point. Typical uses include low- and intermediate-frequency signal generation, voltage-controlled frequency references, sweep and ramp generation, two-channel modulation systems, tone-shaping circuits, and instrumentation. In laboratory equipment, the two sections can generate a carrier and a variable clock. In communications equipment, they can support adjustable local timing or modulation. In industrial controls, they can provide a programmable frequency reference where a fixed crystal oscillator is insufficient. The principal design consideration is signal integrity around the control inputs. Keep control-voltage traces short, isolate them from fast switching nodes, and use a clean reference voltage to prevent frequency jitter. The 20 MHz upper frequency is a maximum device capability rather than a guarantee of useful output quality at every control voltage, load, supply, or temperature. Confirm timing margins and output-waveform requirements in the target system before release. This page organizes the manufacturer product information, exact-orderable package details, sourcing guidance, and engineering selection notes for the SN74LS629N. It also identifies why true drop-in replacements are uncommon: equivalent oscillator functions generally use a different package, pinout, supply family, or control characteristic, making an unverified substitution risky.

RFC Hubungi kami
SN74LS640M - Octal Bus Transceiver | onsemi | SOIC-20
SN74LS640M

SN74LS640M - Octal Bus Transceiver | onsemi | SOIC-20

The onsemi SN74LS640M is an octal bus transceiver designed for asynchronous, two-way communication between data buses, with eight data channels and a 20-pin SOIC-20 (SOEIAJ-20) package. It provides directional control for bus communication and an active-low output-enable function for placing the transceiver outputs in a high-impedance state when the bus is not being driven. A bus transceiver is an interface-circuit category that connects two independently timed digital buses while adding direction and output control. The SN74LS640 belongs to the broader 74LS low-power Schottky TTL logic family, combining bidirectional data paths with bus-driver and bus-receiver functions. Its octal organization allows an entire eight-bit data word to be transferred between two buses through one 20-pin device. The primary benefit of the SN74LS640M is integrated directional control. The DIR input determines the direction of data flow, while the output-enable input provides shared control over the eight output drivers. This arrangement reduces the number of external control gates and simplifies asynchronous system interfacing. Its octal structure also allows parallel processors, memory systems, peripheral controllers, and data-acquisition equipment to use one package for full-width bus buffering. As a member of the SN54LS64x and SN74LS64x bus-transceiver family, the SN74LS640M is covered by the manufacturer's octal bus transceiver datasheet. That document also describes related SN74LS641, SN74LS642, SN74LS645, and military-temperature SN54LS64x devices. Because this is a low-power Schottky TTL device, system designers should preserve adequate input rise and fall times, maintain compatible VCC rails, and avoid excessive capacitive loading on the bus outputs. Typical uses include bidirectional processor-bus isolation, memory-buffer interfaces, peripheral data buses, industrial control data exchange, and legacy digital test equipment. The transceiver is especially useful where two bus masters may alternate control of a shared eight-bit data path. The enable input can also isolate the device during reset, test, or bus turnaround, reducing contention risk when multiple sources share a conductive path. PCB implementation should prioritize short, clean signal traces and a solid ground reference. Place the device close to the bus connector or processor interface, keep the DIR and output-enable traces away from high-current switching paths, and provide local bypass capacitance at VCC. Confirm that the connected devices use compatible TTL signal levels and that the enabled direction matches the intended source and destination buses. This page consolidates the device function, package details, operating context, design guidance, and documented replacement options into one engineering reference. It also identifies where compatibility must be checked against pinout, power requirements, timing, and lifecycle constraints before approving a substitute for an existing design.

RFC Hubungi kami
SN74LS640N - 8-Bit Inverting Bus Transceiver | Texas Instruments
SN74LS640N

SN74LS640N - 8-Bit Inverting Bus Transceiver | Texas Instruments

Texas Instruments SN74LS640N is an 8-bit inverting bus transceiver with 3-state outputs, designed for asynchronous two-way communication between data buses in a 20-pin PDIP package. It transmits data from the A bus to the B bus or from the B bus to the A bus according to the DIR input, while the enable input can disable the device so the buses are effectively isolated. A bus transceiver is a bidirectional interface IC that combines two drivers and two receivers on each data path. The octal bus transceiver belongs to the broader 74LS logic family and provides a defined interface between two system buses. Its inverting outputs support systems designed around active-low bus conventions, while the 3-state outputs allow devices to relinquish control of a shared bus when disabled. The SN74LS640 family provides eight parallel data channels with direction control common to all channels. The DIR input selects the transmission direction, and the enable control provides a means to place the outputs in a high-impedance state. This arrangement supports processor-to-peripheral data transfer, bus isolation during inactive periods, and bidirectional communication between assemblies connected by shared wiring. The key engineering benefit is integration: eight channels, direction control, enable control, and 3-state output behavior are combined in one standard 20-pin PDIP device. The SN74LS640N is appropriate when a legacy system uses LS-family TTL signaling and requires a byte-wide bidirectional bus interface. The N package identifies the through-hole PDIP form rather than a surface-mount package. Typical uses include parallel peripheral interfaces, asynchronous data exchange between circuit cards, test-equipment control buses, and embedded systems that retain 74LS-compatible logic levels. The common DIR and enable controls simplify firmware because direction and bus participation can be managed as grouped signals instead of eight independent channels. For reliable operation, treat unused data inputs as defined logic states and do not allow the DIR and enable control inputs to float. Account for propagation delay and setup/hold requirements at the system level when changing direction near a clock edge. The SN74LS640N can remain powered while its outputs are disabled, allowing another bus master to take control without a complete power-cycle. This page combines the device function, package and interface details with selection guidance for verified drop-in alternatives, practical bus-control considerations, and a parameter-by-parameter comparison for engineers evaluating replacements.

RFC Hubungi kami
SN74LS641H - 8-Bit Open-Collector Bus Transceiver | onsemi
SN74LS641H

SN74LS641H - 8-Bit Open-Collector Bus Transceiver | onsemi

onsemi SN74LS641H is an 8-bit bipolar bus transceiver with open-collector outputs, supplied under the SN74LS logic family. It provides a practical interface between a digital bus and externally driven data lines, supporting legacy TTL-style equipment, control systems, test fixtures, and industrial data-acquisition designs. The device belongs to the buffer, driver, and transceiver hierarchy within digital logic ICs. A bus transceiver combines two directed data paths in one package. Data can move from the bus into the receiving logic, while the driver section presents the opposite signal direction to the external bus. Its open-collector outputs are important because the output stage can provide a wired-AND function when an appropriate pull-up is present. This characteristic is useful in systems where several devices share a signal line or where bus fault handling requires a passive pull-down behavior. The SN74LS641H is associated with the SN74LS641 octal bus-transceiver family. The SN74LS641 family is identified as an octal device with open-collector outputs. The H suffix distinguishes the onsemi ordering variant from the base family name, while its exact package, temperature grade, lifecycle status, and full electrical limits should be selected from the manufacturer’s order information for the complete MPN. As a member of the low-power Schottky TTL family, the device is associated with 74LS-compatible logic systems. Its open-collector interface can support bus-oriented signal conditioning where conventional totem-pole outputs are unsuitable. Designers should nevertheless verify propagation delay, sink current, output rise time, input thresholds, and supply-voltage tolerances against the exact SN74LS641H datasheet before using it as a timing-critical component. Typical uses include interfacing processor buses to open-collector peripherals, communicating with legacy test equipment, isolating logical signals through a bus-driver stage, and building wired-control networks with external pull-up resistors. In each case, the external pull-up value determines the rise time, bus speed, and current drawn while the output transistor is off. The manufacturer application guidance should govern resistor selection and logic-family interfacing. A key design consideration is the difference between a logic-compatible receiver input and an open-collector driver output. The input side may drive from another TTL-family device, while the output side requires suitable pull-up components and must not exceed the published sink-current and voltage limits. Treat the bus as a wired node, calculate its worst-case loading, and verify contention behavior during power-up, reset, and output disable. This product page combines the confirmed SN74LS641H identity with practical guidance for evaluating bus direction, pull-up requirements, package-dependent PCB compatibility, legacy-logic timing, and procurement alternatives. Exact dimensions, pin assignments, and electrical limits remain tied to the ordered package suffix, while the manufacturer datasheet and product page provide the controlling information for design release.

RFC Hubungi kami
SN74LS641N - 8-Bit Open-Collector Bus Transceiver | TI
SN74LS641N

SN74LS641N - 8-Bit Open-Collector Bus Transceiver | TI

The Texas Instruments SN74LS641N is an 8-bit octal bus transceiver with open-collector outputs, supplied in a 20-pin PDIP package. It is designed for 5 V systems and supports bidirectional transfer between A and B data buses through direction-control and output-enable inputs. The operating voltage shown for this device is 4.75 V to 5.25 V, with an output-current capability listed as 12 mA. A bus transceiver is a bidirectional digital interface that allows two logic buses to exchange data while controlling the direction of transmission. The SN74LS641N belongs to the broader logic IC and bus-interface hierarchy, combining eight parallel data channels, direction control, and open-collector output behavior in one integrated circuit. Open-collector outputs can support wired bus arrangements when the system includes suitable pull-up components and circuit protection. The principal features of the SN74LS641N are its eight parallel channels, non-inverting data transfer, open-collector outputs, and separate direction control. The device transfers data from the A bus to the B bus or from the B bus to the A bus according to the DIR input state. Its 20-pin PDIP package is intended for conventional through-hole PCB assembly rather than surface-mount production. The SN74LS641N belongs to the SN74LS family of Low-Power Schottky TTL-compatible logic devices. Open-collector output stages are the defining architectural feature, while the direction-control inputs determine which side of the transceiver drives the bus. Because the outputs are open collector, external pull-up resistors are normally required for high-level output states. Exact propagation-delay, output-voltage, input-current, and power-consumption limits should be confirmed in the manufacturer datasheet before release to production. Typical uses include bidirectional parallel-bus interfaces, embedded data acquisition, peripheral isolation, legacy computer buses, and industrial control modules where two logic domains must exchange eight data lines. The device is especially relevant to designs that require controllable bus direction and wired-AND behavior. It can also support bus turnaround in systems where a bus driver changes between source and sink operating modes. PCB design should provide a solid ground plane, minimize loop lengths around direction and enable controls, and place pull-up resistors close to the open-collector bus pins. The 4.75 V to 5.25 V supply range requires a stable 5 V rail. Designers should also account for the additional current drawn by pull-up resistors and verify that every connected bus node can tolerate the resulting pull-up current. This product record combines device classification, source links, drop-in replacement analysis, package considerations, and practical interface guidance. The comparison and application sections clarify where the SN74LS641N fits within octal bus-transceiver designs and which technical details must be checked against the manufacturer datasheet.

RFC Hubungi kami
SN74LS642N - 8-Bit Open-Collector Bus Transceiver | TI
SN74LS642N

SN74LS642N - 8-Bit Open-Collector Bus Transceiver | TI

The Texas Instruments SN74LS642N is an octal, 8-bit, inverting bus transceiver with open-collector outputs, operating from a 4.75 V to 5.25 V supply in a 20-pin PDIP package. It supports bidirectional asynchronous data-bus communication by transferring data from bus A to bus B or from bus B to bus A according to the DIR input. The G enable input can disable the device to isolate the buses. A bus transceiver is a logic interface that connects two data buses and allows data to travel in either direction. The SN74LS642 belongs to the 74LS low-power Schottky TTL logic family and combines eight bidirectional bus channels with direction and enable control. Open-collector outputs are particularly useful when a bus requires pull-up resistors, wired-AND behavior, or compatibility with another logic family. Key features include eight 1-bit transceiver elements, an inverting data path, open-collector output capability, a 4.75 V to 5.25 V operating range, 12 mA output-current capability, and Schmitt-trigger input behavior. The direction input determines which bus drives the other, while the enable input provides a common control for disabling the transceiver and reducing bus contention. The device is designed for asynchronous, two-way communication between computer or peripheral buses. Its open-collector architecture requires correctly sized external pull-up resistors on each bus. Pull-up resistance, bus capacitance, sink-current capability, and maximum data rate must be considered together because increasing resistance reduces current demand but can slow bus transitions and increase susceptibility to noise. Typical applications include bidirectional instrument buses, peripheral-interface isolation, test and measurement systems, computer data buses, and industrial control interfaces. In each case, the DIR input selects the transmitting direction, while G controls whether the enabled device participates in the bus transaction. The 20-pin PDIP package is suited to through-hole boards and legacy system maintenance. For reliable operation, place pull-up resistors close to the open-collector outputs and keep the shared bus traces short enough to control ringing and crosstalk. Confirm that the external pull-up network can source the required receiver current without exceeding the device's output specifications. Do not enable opposing drivers on the same bus. This page combines device architecture, package and pin information, replacement guidance, comparison criteria, and practical bus-interface design notes to support component selection and board-level implementation.

RFC Hubungi kami
SN74LS645H - Octal Bus Transceiver | Texas Instruments
SN74LS645H

SN74LS645H - Octal Bus Transceiver | Texas Instruments

Texas Instruments SN74LS645H is an octal bus transceiver designed for asynchronous two-way communication between data buses. The device provides eight parallel data channels, non-inverting transceiver operation, and three-state output control. It is intended for systems in which two bus masters, processors, peripheral devices, or memory devices must exchange data over a shared bus. A bus transceiver is a bidirectional interface IC that combines driver and receiver functions. It allows a device to transmit logic levels onto a bus and receive logic levels from that same bus. The SN74LS645 family reduces the number of external timing requirements by coordinating bus direction and output-enable control, while the three-state outputs permit multiple devices to share common data lines without driving them simultaneously. The SN74LS645 is one member of the SN54LS and SN74LS low-power Schottky TTL logic families. Low-power Schottky TTL combines bipolar transistor logic with Schottky-clamped input stages. This technology is associated with the 74LS family’s established logic levels, system design heritage, and broad use in legacy digital equipment. The octal organization means that one device handles eight signal lines in parallel rather than requiring eight separate single-bit interface circuits. The H suffix identifies the orderable SN74LS645H configuration listed for the octal bus transceiver family. The manufacturer product page and supporting technical descriptions identify the device as an octal transceiver for asynchronous two-way bus communication. Detailed electrical limits, propagation timing, supply-current behavior, temperature grade, and package dimensions should be confirmed in the manufacturer datasheet before release to production. Typical uses include bidirectional processor and peripheral buses, memory-interface buffering, data acquisition systems, test equipment, industrial control logic, and repairs of legacy TTL-based hardware. The device is especially useful where a shared bus requires controllable drive direction and a high-impedance state so that only one participant actively drives the lines during a given transaction. Designers should verify direction and enable truth tables, propagation delay, setup and hold timing, input and output loading, and the available input-to-output voltage margin in the system. A shared bus also requires a defined arbitration method so that no two drivers enable the same line simultaneously. Decoupling and signal-return paths should follow the recommended layout in the manufacturer documentation. This page combines the official product identity with package-oriented sourcing context, replacement guidance, application patterns, and design cautions. The comparisons emphasize electrical and functional interchangeability rather than treating every similarly named 74-series component as a safe substitute. Verify timing and logic behavior on the target board, especially when replacing a component across manufacturers or between commercial and extended-temperature variants.

RFC Hubungi kami
SN74LS645N - 8-Bit 3-State Bus Transceiver | Texas Instruments
SN74LS645N

SN74LS645N - 8-Bit 3-State Bus Transceiver | Texas Instruments

Texas Instruments SN74LS645N is an 8-bit, non-inverting, 3-state bus transceiver with a 20-pin PDIP package. It operates from a 4.75 V to 5.25 V supply, supports asynchronous two-way communication between data buses, and includes Schmitt-trigger inputs with a 15 mA sink capability. The device is designed for systems that need to place one side of an eight-bit data path into a high-impedance state so that multiple bus drivers can share a common conductor. An octal bus transceiver is a bidirectional interface IC that combines a bus driver, receiver, and direction-control logic in one package. Within the broader hierarchy of interface ICs, it supports the 74LS bipolar logic family and the TTL-compatible 5 V system environment. Its eight parallel channels make it suitable for routing byte-wide data among processor, memory, peripheral, and backplane interfaces without requiring eight separate single-channel transceivers. The main features include non-inverting data transfer, 3-state output control, eight independently usable I/O paths, and Schmitt-trigger input behavior. The Schmitt trigger helps improve noise tolerance by providing hysteresis at the input threshold. The 3-state output can actively drive a logic high or low, or present a high-impedance state when disabled, allowing several devices to share a bus when only one driver is enabled at a time. The 20-pin PDIP format also supports conventional through-hole assembly and prototyping. Technically, the SN74LS645N combines directional control with bus-state management. Direction and output-enable inputs determine whether data flows from the A-side bus to the B-side bus, from B to A, or remains disabled at the outputs. Because this is a bipolar 74LS-family device, designers should account for the logic levels, transition timing, fanout, and supply tolerances associated with that family rather than treating it as a modern low-voltage CMOS bus device. Typical uses include bidirectional eight-bit CPU and peripheral buses, data multiplexers, test equipment, memory-interface routing, and industrial control boards. In each case, the transmitter is useful where two bus masters or independent subsystems must exchange byte-wide data while retaining tri-state control over bus ownership. The SN74LS645N is most appropriate when legacy 5 V TTL signaling, through-hole construction, and established 74LS interoperability are priorities. During layout, keep the data paths short and route the eight corresponding A and B signals as matched groups. Place decoupling close to the supply pins, provide a common ground reference, and confirm that enable and direction timing does not create contention. This page combines verified product attributes, documented replacement options, and practical bus-interface design guidance for faster component selection.

RFC Hubungi kami
SN74LS682N - 8-Bit Magnitude Comparator | Texas Instruments
SN74LS682N

SN74LS682N - 8-Bit Magnitude Comparator | Texas Instruments

The Texas Instruments SN74LS682N is an 8-bit identity and magnitude comparator that compares two binary or BCD words and provides active-low equality and greater-than outputs. It is packaged in a 20-pin PDIP and uses the low-power Schottky TTL logic family for compatible digital-system interfacing. The SN74LS682N supports two 8-bit input buses, A and B, allowing a system to determine whether A equals B or whether A is greater than B. According to the manufacturer datasheet, the device also uses totem-pole output structures. An identity or magnitude comparator is a combinational logic device that accepts two multi-bit operands and produces outputs describing their relative relationship. The SN74LS682 belongs to the broader 74LS comparator family, where an 8-bit magnitude comparator compares parallel data rather than determining the order of two individual bits. Its identity function provides a direct equality result, while its magnitude function provides a greater-than result. These operations are useful in control, sorting, address matching, arithmetic sequencing, and test systems. The principal feature of the SN74LS682N is its dedicated 8-bit comparison architecture. Each operand is presented on a parallel bus, and the internal logic evaluates the complete word rather than requiring a serial sequence of bit-by-bit comparisons. The device provides active-low A=B and A>B outputs, enabling wired-output systems to combine several comparator results. Its 74LS Schottky TTL construction is suited to conventional five-volt logic environments, while the through-hole PDIP package simplifies assembly, inspection, and replacement in legacy or industrial control equipment. The SN74LS682N differs from related devices in the same 74LS family primarily by its output set. The LS682 supplies equality and greater-than functions; not every related magnitude comparator offers the same combination. This distinction is important because a substitute with the same package and pin count is not automatically interchangeable if its output behavior differs. Engineers should compare truth tables, propagation timing, output polarity, supply requirements, and input-current characteristics before approving any replacement. Typical uses include equality detection in digital control systems, BCD value comparisons in industrial controllers, parallel sorting and routing logic, address and identification-word recognition, and legacy test equipment. The comparator can also serve as the central decision element in alarm and sequencing circuits where two eight-bit values must be tested continuously. Its parallel interface makes it suitable when the system already presents complete words and requires a hardware-generated status indication without microcontroller comparison code. PCB design should preserve clear separation between the two operand buses and route each input directly to its corresponding package pin. Decoupling requirements, grounded-return practices, unused-input handling, and TTL input-current budgeting must follow the manufacturer datasheet. Because outputs are active low and totem-pole structured, downstream circuits should account for both voltage levels and fan-out rather than treating the outputs as ideal push-pull signals. Socketed prototypes should also account for contact resistance and contamination at older through-hole connections. This product page combines the manufacturer function description, package information, family distinctions, pin-verification guidance, and application-oriented replacement criteria to support engineering selection. It also identifies the limits of package-only compatibility: a true drop-in replacement must reproduce the SN74LS682N output truth table and electrical timing in addition to matching the 20-pin PDIP footprint.

RFC Hubungi kami
SN74LS684N - 8-Bit Magnitude Comparator | Texas Instruments
SN74LS684N

SN74LS684N - 8-Bit Magnitude Comparator | Texas Instruments

The Texas Instruments SN74LS684N is an 8-bit identity and magnitude comparator for binary or BCD words, with active-low A=B and A>B outputs in a 20-pin PDIP package. It compares two parallel 8-bit operands and reports whether the inputs are equal or whether the first operand is greater than the second, supporting arithmetic control, address decoding, test systems, and industrial decision logic. A magnitude comparator is a logic IC that determines the relative ordering of two multibit numbers. It belongs to the comparator, digital logic, logic IC, and semiconductor hierarchies. Unlike a general-purpose processor or programmable controller, the SN74LS684N performs its comparison directly from wired logic inputs, so the result becomes available without firmware or instruction sequencing. The SN74LS684N supports both binary and BCD comparison, and its active-low indication outputs are useful for driving downstream enable, reset, or selection logic. The device is listed in a 20-pin PDIP package with a 0 to 70 °C operating-temperature range. These characteristics make it appropriate for legacy-compatible equipment, industrial control systems, counters, timers, test fixtures, and interface designs that retain through-hole logic boards. The LS series implementation uses Schottky-clamped TTL-compatible logic. Its structured outputs indicate the comparison result while external cascaded logic can extend comparison beyond the native 8-bit width. Design engineers should therefore treat the comparator outputs as active levels rather than passive status indicators, account for propagation delay when chaining stages, and use pull-up or pull-down components wherever the receiving circuit requires a defined inactive level. Typical applications include sorting and classification control, digital test-equipment limit checking, address and threshold comparison, arithmetic-unit control, BCD instrument processing, and industrial sequence controllers. In these systems, the two operand buses feed the comparator, while its equality and greater-than outputs coordinate a counter, register, latch, or alarm without requiring continuous software polling. A critical PCB consideration is the 20-pin PDIP footprint. Pin-1 orientation, notch direction, and adequate spacing around the package must match the board pattern, especially when repairing legacy equipment. Keep the input and output traces short enough to limit propagation-delay uncertainty, and account for the operating-temperature limits when using the part outside controlled room-temperature environments. This product page consolidates the device identity, package information, operating range, comparison functions, sourcing structure, replacement guidance, and practical logic-design considerations into an engineering-focused reference. It also highlights the limits of direct substitution by separating true pin-compatible options from related comparator functions that do not reproduce every output and feature of the SN74LS684N.

RFC Hubungi kami
SN74LS685N - 8-Bit Magnitude Comparator | Texas Instruments
SN74LS685N

SN74LS685N - 8-Bit Magnitude Comparator | Texas Instruments

The Texas Instruments SN74LS685N is an 8-bit magnitude and identity comparator with inverted logic outputs, supplied in a 20-pin PDIP package. It compares two 8-bit binary numbers and indicates whether the A input is greater than, less than, or equal to the B input. Its three comparison indications support magnitude testing, identity detection, address decoding, conditional control, and digital sorting functions. The SN74LS685N belongs to the LS series of TTL logic and operates as a dedicated combinational comparator rather than a general-purpose arithmetic processor. A magnitude comparator is a digital logic IC that compares two multi-bit unsigned values and produces relational outputs. The SN74LS685N performs this function across two complete 8-bit input groups, reducing the need for several single-bit comparator or gate networks. Magnitude comparators sit within the broader logic-IC hierarchy, alongside arithmetic, interface, memory, and control devices. Their outputs can indicate equality as well as the direction of the numerical relationship, making them useful between data-processing blocks and system decision logic. The defining features are an 8-bit comparison width, inverted comparison outputs, LS-series TTL implementation, and PDIP-20 mechanical package. The inverted outputs are important during logic design because active-low assertions must be treated consistently with the rest of the circuit. The NS suffix identifies the standard Texas Instruments package and commercial-temperature ordering configuration. Because the device uses a through-hole PDIP package, it can also suit educational, industrial-control, test-equipment, and legacy-computing assemblies where through-hole assembly and socketed serviceability remain practical. The SN74LS685N provides a straightforward hardware comparison stage. Two 8-bit buses enter the comparator, while dedicated outputs report the relationship between them. This allows a system to make a decision without first subtracting the operands or comparing them sequentially in a processor. The architecture is particularly useful when a decision must be generated quickly and consistently, or when control logic must respond to equal, greater-than, and less-than conditions independently. Typical applications include digital address decoding, equality checking in control systems, threshold decision logic, numeric sorting networks, event counters, legacy processor interfaces, and industrial automation equipment. In an address decoder, for example, the comparator can test whether a bus matches a programmed or dynamically generated value and enable the associated circuit only when equality is asserted. In test equipment, its three relational outputs can simplify fixture routing and pass-fail detection. PCB design should preserve the logic polarity of the inverted outputs and route each 8-bit input group as a coherent bus to reduce mismatch between corresponding bits. Maintain adequate bypass capacitance at the power pins and avoid relying on the comparator outputs to source loads beyond the device's specified output-current and fan-out limits. When replacing an existing part, verify the complete pinout, supply requirements, temperature range, output timing, and propagation-delay characteristics rather than relying on the comparator function alone. This product page combines the device identity, package details, functional hierarchy, comparison design guidance, practical applications, and drop-in replacement analysis into an engineering-focused reference for the Texas Instruments SN74LS685N 8-bit magnitude comparator.

RFC Hubungi kami
SN74LS688N 8-Bit Identity Comparator | Texas Instruments
SN74LS688N

SN74LS688N 8-Bit Identity Comparator | Texas Instruments

The Texas Instruments SN74LS688N is an 8-bit identity and magnitude comparator in a 20-pin plastic dual in-line package. It compares two 8-bit binary or BCD words and provides a dedicated P=Q output, while a low-active enable input controls whether the comparison output is actively driven. The device belongs to the SN74LS TTL logic family and is intended for digital systems that need a fast equality decision without implementing the comparison function in general-purpose logic. A magnitude comparator is a combinational logic device that evaluates the relative relationship between two multi-bit values. An identity comparator is the equality-focused subset of that category: instead of reporting greater-than and less-than relationships, the SN74LS688N asserts its P=Q result when the two input words match. In system terms, the device sits between two data buses and a downstream control or decoding circuit, converting eight parallel bit comparisons into one consolidated status signal. The principal features of the SN74LS688N are its 8-bit binary or BCD input capability, P=Q output with enable control, totem-pole output structure, and input hysteresis. These characteristics make it useful where noise immunity and stable switching behavior are important in TTL-compatible equipment. The N suffix denotes the plastic through-hole package, which supports conventional 0.100-inch lead pitch layouts, prototyping, repair work, and legacy industrial control equipment. Internally, the SN74LS688N organizes the comparison into a chain of logic stages that examine corresponding bits from the P and Q buses. Each stage propagates the higher-order comparison result toward the output, allowing the final P=Q signal to reflect the complete eight-bit relationship. External enable control prevents the output from changing state while the compared data is being updated, helping downstream circuitry avoid interpreting intermediate bus states as valid comparisons. Typical applications include digital test equipment, industrial control panels, memory and address checking, sorting and routing control, legacy processor subsystems, and general-purpose binary or BCD data validation. The chip is especially useful when a fixed-width equality result is needed but a larger programmable comparator would be unnecessary. It can also form part of a multi-stage comparison system when several independent 8-bit sections must be checked separately. When laying out a board around the SN74LS688N, maintain the standard 20-pin through-hole footprint and route the two input buses away from high-current switching nodes. The enable input should be driven only when both buses are stable, and unused inputs should be tied to a defined TTL level rather than left floating. Because this is a legacy through-hole logic device, designers should also verify the system supply level, input thresholds, output timing, and noise margin against the manufacturer datasheet before releasing a new production design. This product page adds engineering context beyond the basic catalog entry by organizing the comparison function, package details, application fit, verified source links, and realistic replacement constraints. It also highlights that true drop-in alternatives are limited: substitute parts must preserve the 20-pin footprint, pin functions, logic levels, P=Q behavior, and enable timing rather than merely offering a superficially similar 8-bit comparator.

RFC Hubungi kami
SN74LS68N - 4-Bit Parallel Binary Accumulator | Texas Instruments
SN74LS68N

SN74LS68N - 4-Bit Parallel Binary Accumulator | Texas Instruments

The Texas Instruments SN74LS68N is a 4-bit parallel binary accumulator counter IC with a listed price of $0.5606 from LCSC as of 2026-10-22 and a verified in-stock listing. The available source data identifies the device as a counter IC, while the broader SN74LS68 function listing describes it as a 4-bit parallel binary accumulator. Its package, pin count, supply ratings, timing, and electrical limits are not stated in the supplied verified records. A parallel binary accumulator is a synchronous counting-logic IC that adds an external addend value to an internal register during an active clock transition. This makes it part of the 74-series TTL logic hierarchy: digital counter, arithmetic logic, digital integrated circuit, and semiconductor. Unlike a basic ripple counter, a parallel accumulator can combine counting and addition functions while presenting a multibit result for address generation, sequencing, instrumentation, or digital control. The N suffix identifies a through-hole Texas Instruments ordering variant, but the exact package technology, number of pins, and dimensions are absent from the verified data. Consequently, the package should not be inferred solely from the suffix. Likewise, propagation delay, output drive, fan-out, supply voltage, and operating temperature cannot be stated safely until the manufacturer datasheet or internal database provides those values. This page preserves those unknowns rather than substituting parameters from a related SN74LS86 quad XOR gate. Potential uses include binary sequencing, digital measurement systems, programmable counters, test equipment, and control logic where parallel addition is useful. Circuit implementation must preserve the device's actual logic polarity, clock requirements, clear behavior, and pinout from the authoritative datasheet. Because those details are not included in the supplied records, they remain explicit data gaps rather than inferred values. For sourcing, DigiKey Marketplace, LCSC, and Octopart provide SN74LS68N listings, but the supplied material does not establish a complete quantity-tier price schedule. LCSC explicitly reports an in-stock status and a starting price of $0.5606. Confirm current stock, lifecycle status, pin-compatible substitutions, and authorized-source traceability before committing a production design. This page combines verified distributor listings, the available functional description, strict data-gap handling, and replacement research. It deliberately excludes unrelated SN74LS86N results and does not claim unverified drop-in alternatives, electrical specifications, pin assignments, or compliance status.

RFC Hubungi kami
SN74LS697N - 4-Bit Synchronous Up/Down Counter | Texas Instruments
SN74LS697N

SN74LS697N - 4-Bit Synchronous Up/Down Counter | Texas Instruments

The Texas Instruments SN74LS697N is a synchronous 4-bit up/down binary counter with output registers and multiplexed three-state outputs, packaged in a 20-pin PDIP. It combines counting, registered output storage, and bus-oriented output control in one logic device. The device increments or decrements on the active edge of the clock input, supports a 0°C to 70°C operating-temperature grade, and is intended for digital counting and timing systems. A synchronous binary counter is a sequential logic device whose internal state changes in step with an active clock edge. The SN74LS697 belongs to the broader 74LS TTL logic family and combines a counter element with parallel output registers. Its up/down control permits operation as an incrementing counter, decrementing counter, or programmable frequency-divider stage. The output-register stage separates the counting sequence from the signals presented at the multiplexed outputs. The principal features include one 4-bit counting element, a positive-edge clock input, directional counting control, registered outputs, and three-state output capability. The three-state outputs allow multiple counters or other bus-driving devices to share a common data bus when output-enable control is active. This combination is useful in systems requiring orderly bus access, event sequencing, or synchronized transfer of counter values. The SN74LS697N is a member of the SN74LS logic series and uses the SN74LS697 function designation. Its registered outputs provide a defined output state between active clock events, while the synchronous counting architecture simplifies designs where multiple counting stages must update in step. When cascading devices, the carry output can be used to extend counting range and coordinate event boundaries. Typical applications include frequency division, pulse and event counting, programmable timing modules, digital test equipment, industrial sequence controllers, and bus-oriented digital subsystems. The device can also serve as the central counting element in measurement systems that must divide an input frequency, count fixed-duration events, or present a latched hexadecimal or binary count to a host processor. Designers should use the pin-description table in the Texas Instruments SN74LS697 datasheet when assigning PCB signals, especially for output-enable and directional-control pins. Because the outputs are multiplexed and three-state capable, the system must keep output-enable and bus-control timing separate from the clock edge requirements. Unused inputs should be held at a defined logic level according to the datasheet guidance. This page combines the Texas Instruments function description, package information, application guidance, sourcing questions, and replacement constraints into a practical engineering reference for the SN74LS697N. It also distinguishes a verified function-compatible ordering suffix from a genuine cross-manufacturer drop-in equivalent, helping designers avoid assuming that similar counter ICs are pin-compatible without reviewing their datasheets.

RFC Hubungi kami
SN74LS699N - Synchronous Up/Down Counter | Texas Instruments
SN74LS699N

SN74LS699N - Synchronous Up/Down Counter | Texas Instruments

Texas Instruments SN74LS699N is a synchronous up/down counter with an output register and multiplexed three-state outputs, packaged in a 20-pin plastic DIP. It combines binary counting, direction control, registered parallel outputs, and bus-driving capability in one counter IC. The SN74LS699N is associated with the 74LS TTL logic family and is intended for digital control, sequencing, address-generation, and instrumentation systems where registered counter state must drive shared buses. A counter IC is a member of the broader digital logic hierarchy and increments or decrements a binary state in response to clock events. The 74LS699 architecture adds an output register between the counting section and the external outputs, allowing the presented value to change on a defined clock edge rather than immediately after each internal count transition. This registered architecture helps prevent data races when multiple counters or peripherals share a bus. The principal functional features include synchronous counting in up or down directions, parallel output registers, and multiplexed three-state outputs. Synchronous operation means the counter state advances on the active clock edge, simplifying timing analysis in multi-stage digital systems. The three-state outputs can place each output in a high-impedance state when the device is not driving the shared bus, helping reduce bus contention when several compatible devices are connected. The device belongs to the LS logic series, using bipolar TTL-compatible signal levels and standard 74LS-family interface conventions. The output-register stage separates internal counting activity from bus presentation, while the multiplexer determines which registered information appears on the output bus. Designers should consult the manufacturer pin-description table before assigning PCB tracks because each physical pin must be connected according to its dedicated clock, control, count, or output function. Typical uses include programmable timing generators, pulse and sequence counters, industrial control logic, test-and-measurement equipment, and address or event-counting subsystems. The SN74LS699N is particularly useful when a downstream device requires stable parallel data synchronized to the system clock rather than continuously changing combinational counter outputs. For new PCB layouts, preserve the standard 20-pin DIP footprint and route all supply pins according to the manufacturer datasheet. Avoid substituting a functionally similar counter without checking output timing, output-enable behavior, clear or load semantics, and the exact multiplexing arrangement. These details determine whether a replacement is truly pin-compatible rather than merely equivalent at a high level. This product page combines the counter's core function with package guidance, replacement criteria, comparison data, and practical implementation notes. It is designed to help engineers identify the correct 74LS-family counter, verify bus-interface compatibility, and plan a board-level replacement without overlooking the distinctions between registered, multiplexed, and three-state output implementations.

RFC Hubungi kami
SN74LS69D - Dual 4-Bit Counter, 16-Pin SOIC | Texas Instruments
SN74LS69D

SN74LS69D - Dual 4-Bit Counter, 16-Pin SOIC | Texas Instruments

Texas Instruments SN74LS69D is a dual 4-bit binary counter operating from a 4.75 V to 5.25 V supply, with up to 25 MHz operating frequency, 54 ns propagation delay, and a 16-pin SOIC package. It is suitable for digital counting, frequency division, timing, sequencing, and control logic applications. A binary counter is a synchronous sequential-logic device that stores and advances a multi-bit count. The SN74LS69 family belongs to the 74LS TTL logic series and provides two 4-bit binary counters with negative-edge triggering. Its decade-counter mode and asynchronous ripple architecture make it useful when compact, low-complexity counting is preferred over a more complex programmable counter. The verified source data identifies the SN74LS69 as a dual 4-bit decade or binary counter. The SN74LS69D ordering code uses the SOIC-16 package. Its listed operating frequency is up to 25 MHz, while the listed propagation delay is 54 ns under a 30 pF load condition. The specified supply-voltage range is 4.75 V to 5.25 V. Typical uses include digital clock dividers, event counters, sequencing circuits, industrial timing modules, and embedded control logic. Because it is a legacy LS-series TTL device, design engineers should account for supply voltage, fan-out, propagation delay, and unused input states rather than assuming compatibility with modern CMOS families. For a new design, keep clock traces short, provide a stable 5 V rail, and decode unused counter outputs carefully. Ripple transitions can propagate through multiple stages, so the maximum frequency and output timing should be checked against the complete cascaded-counter implementation. Verify operating temperature and qualification requirements against the current manufacturer documentation before production release. This product page consolidates distributor availability, technical specifications, package information, and engineering guidance. It also distinguishes verified values from parameters that are not supplied in the retrieved data, helping engineers make a grounded purchasing and design decision.

RFC Hubungi kami
SN74LS69N - Dual 4-Bit Counter | Texas Instruments | Logic
SN74LS69N

SN74LS69N - Dual 4-Bit Counter | Texas Instruments | Logic

The Texas Instruments SN74LS69N is a dual 4-bit binary counter IC with a 5 V nominal supply, 54 ns propagation delay, and 16 through-hole terminals in a rectangular DIP package. It contains two independent 4-bit counters that count upward and provide parallel binary outputs for each counter section. A binary counter is a synchronous sequential-logic component that records a number as a sequence of binary bits. A 4-bit counter can represent 16 states from 0000 through 1111. As a digital counter IC, the SN74LS69N belongs to the 74LS low-power Schottky TTL family, where digital logic ICs implement counting, timing, and state-sequencing functions within broader control and embedded systems. The principal verified characteristics include dual 4-bit counter organization, upward counting, 54 ns propagation delay, 5 V nominal operating voltage, 16 terminals, commercial temperature grade, and through-hole DIP construction. These specifications make the device suitable for legacy digital control, event counting, sequencing, and industrial automation systems that accept standard 16-pin DIP logic footprints. The SN74LS69N provides two counter sections on one package, reducing board area compared with separate single-counter ICs. Its binary outputs can represent the current count directly, allowing external combinational logic, display drivers, memory systems, or control circuitry to interpret each clock interval. The 54 ns delay provides a concrete timing basis for maximum operating frequency and setup/hold requirements, although a complete design should also examine the complete datasheet waveform and load conditions. Typical applications include industrial batch and piece counting, digital event sequencing, test-equipment timing, legacy process-control interfaces, and educational digital-logic systems. Because the verified listing identifies upward counting and a DIP package, the part is especially relevant to through-hole industrial control boards, repair inventories, and modernization projects that need to preserve an existing 16-pin logic layout. When designing around the SN74LS69N, verify the complete pin assignment, clock-edge requirements, clear behavior, supply tolerances, and output-drive limits against the manufacturer datasheet before layout release. Decoupling and signal-integrity practices remain important even at 54 ns propagation delay: provide local supply bypassing, maintain short clock traces, and avoid relying on long PCB interconnects where edge-sensitive timing could be affected. This page combines verified distributor information, the package and timing data available from market listings, practical legacy-logic design guidance, and carefully qualified drop-in alternatives. It is intended to support component selection and sourcing decisions while clearly separating verified facts from information that still requires confirmation from the full manufacturer documentation.

RFC Hubungi kami
SN74LS85D - 4-Bit Magnitude Comparator | Texas Instruments
SN74LS85D

SN74LS85D - 4-Bit Magnitude Comparator | Texas Instruments

The Texas Instruments SN74LS85D is a 4-bit magnitude comparator that compares two four-bit words, A and B, and produces active-high decisions for A<B, A=B, and A>B. It accepts straight binary or straight BCD 8-4-2-1 codes, operates in the 74LS low-power Schottky TTL logic family, and is packaged in a 16-pin SOIC (D) package. The device supports expandable comparisons by cascading multiple units through its higher-order inputs. Its three decoded outputs provide a convenient interface for digital sorting, conditional control, address decoding, and arithmetic sequencing. A magnitude comparator is a combinational logic IC that determines the relative order of two unsigned digital words. Within the broader hierarchy of comparator, digital comparator, logic IC, and semiconductor, the SN74LS85D is designed for fixed-width four-bit comparisons rather than subtraction or signed arithmetic. Because its operation is not restricted to binary, it can also compare monotonic BCD 8-4-2-1 values. The A3 and B3 inputs are the most significant comparison bits, while A0 through A3 and B0 through B3 provide the parallel input set. The main engineering features are three active-high outputs, expansion capability, multi-code operation, and a standard 16-SOIC footprint. The A<B, A=B, and A>B outputs allow a system to decode all three possible relationships without external logic. Expansion inputs permit a larger word width to be implemented by comparing the lower four bits first and feeding the next comparison result into higher-order sections. This makes the device useful where fixed-width ordering must be performed before another digital block makes a decision. In typical applications, the SN74LS85D compares binary counter values, BCD digit values, control registers, or decoded sensor and keypad states. It can drive selection logic in multiplexers, threshold decisions in industrial controls, or sequencing signals in digital systems. Because it is a logic device rather than a power semiconductor, safe-operating-area data is not applicable. Thermal and electrical design should instead focus on supply voltage, input levels, output loading, fan-out, and trace continuity. A key design consideration is to treat unused inputs deliberately. Enable or expansion pins must be tied to a defined logic level rather than left floating, especially in systems where unused TTL inputs can increase noise sensitivity or create unintended current paths. Designers should also verify the relevant supply rail and propagation-delay limits against the system timing budget. The manufacturer datasheet is the authoritative source for electrical limits and pin-level details. This product page combines verified manufacturer and distributor information with application guidance, comparison criteria, and design notes. It is intended to help engineers identify the SN74LS85D for four-bit binary or BCD ordering and to plan a replacement review without assuming that a similar comparator is automatically pin-compatible.

RFC Hubungi kami
SN74LS85DR - 4-Bit Magnitude Comparator | Texas Instruments (Tape & Reel)
SN74LS85DR

SN74LS85DR - 4-Bit Magnitude Comparator | Texas Instruments (Tape & Reel)

The Texas Instruments SN74LS85DR is a 4-bit magnitude comparator that compares two four-bit words, A and B, and produces active-high decisions for A<B, A=B, and A>B. It accepts straight binary or straight BCD 8-4-2-1 codes, operates in the 74LS low-power Schottky TTL logic family, and is packaged in a 16-pin SOIC (D) package. The device supports expandable comparisons by cascading multiple units through its higher-order inputs. Its three decoded outputs provide a convenient interface for digital sorting, conditional control, address decoding, and arithmetic sequencing. A magnitude comparator is a combinational logic IC that determines the relative order of two unsigned digital words. Within the broader hierarchy of comparator, digital comparator, logic IC, and semiconductor, the SN74LS85DR is designed for fixed-width four-bit comparisons rather than subtraction or signed arithmetic. Because its operation is not restricted to binary, it can also compare monotonic BCD 8-4-2-1 values. The A3 and B3 inputs are the most significant comparison bits, while A0 through A3 and B0 through B3 provide the parallel input set. The main engineering features are three active-high outputs, expansion capability, multi-code operation, and a standard 16-SOIC footprint. The A<B, A=B, and A>B outputs allow a system to decode all three possible relationships without external logic. Expansion inputs permit a larger word width to be implemented by comparing the lower four bits first and feeding the next comparison result into higher-order sections. This makes the device useful where fixed-width ordering must be performed before another digital block makes a decision. In typical applications, the SN74LS85DR compares binary counter values, BCD digit values, control registers, or decoded sensor and keypad states. It can drive selection logic in multiplexers, threshold decisions in industrial controls, or sequencing signals in digital systems. Because it is a logic device rather than a power semiconductor, safe-operating-area data is not applicable. Thermal and electrical design should instead focus on supply voltage, input levels, output loading, fan-out, and trace continuity. A key design consideration is to treat unused inputs deliberately. Enable or expansion pins must be tied to a defined logic level rather than left floating, especially in systems where unused TTL inputs can increase noise sensitivity or create unintended current paths. Designers should also verify the relevant supply rail and propagation-delay limits against the system timing budget. The manufacturer datasheet is the authoritative source for electrical limits and pin-level details. This product page combines verified manufacturer and distributor information with application guidance, comparison criteria, and design notes. It is intended to help engineers identify the SN74LS85DR for four-bit binary or BCD ordering and to plan a replacement review without assuming that a similar comparator is automatically pin-compatible.

RFC Hubungi kami
SN74LS85N - 4-Bit Magnitude Comparator | Texas Instruments
SN74LS85N

SN74LS85N - 4-Bit Magnitude Comparator | Texas Instruments

The Texas Instruments SN74LS85N is a 4-bit magnitude comparator with eight parallel data inputs, three active-high decision outputs, and 16-PDIP packaging. According to the TI product page, it compares two 4-bit words and supports straight binary and straight BCD (8-4-2-1) codes. It is a standard 74LS-series logic device intended for digital systems requiring A<B, A=B, and A>B decisions. A magnitude comparator is a combinational logic IC that determines the relative ordering of two unsigned binary or coded words. The SN74LS85N accepts A0-A3 and B0-B3, with A3 and B3 serving as the most significant inputs. Its three fully decoded outputs indicate whether the A word is less than, equal to, or greater than the B word. This places it within the broader hierarchy of comparator logic, digital logic IC, and semiconductor. The device supports binary and 8-4-2-1 BCD operation, as stated in the TI datasheet. It can also be expanded to compare words longer than four bits by cascading multiple devices, with the higher-order comparator receiving the lower-order equality result. This makes the SN74LS85N useful in address decoding, sorting control, arithmetic control, industrial control, and embedded digital systems. The SN74LS85N is identified as a 16-pin PDIP by the distributor data. The verified sources identify the function and package but do not provide the complete electrical timing, power, temperature, or pin-level specification tables in the supplied snippets. Those values are therefore marked as data needed rather than inferred. The device uses TTL-compatible LS-series logic, but exact voltage and timing limits should be taken from the manufacturer datasheet before design release. Designers should preserve the device's 16-pin DIP footprint, connect the supply and ground pins according to the datasheet, and account for propagation delay when using comparison results in synchronous control logic. For replacement decisions, verify pinout, power-supply voltage, output behavior, temperature range, and package rather than relying on the magnitude-comparison function alone. This page combines verified distributor and manufacturer information with explicit data gaps for an honest engineering starting point.

RFC Hubungi kami
SN74LS90D - Decade Counter, 4-Bit, LS-TTL, 14-SOIC | Texas Instruments
SN74LS90D

SN74LS90D - Decade Counter, 4-Bit, LS-TTL, 14-SOIC | Texas Instruments

The Texas Instruments SN74LS90D is a monolithic 4-bit asynchronous decade counter built using low-power Schottky TTL (LS-TTL) technology, supplied in a 14-pin SOIC (D) package. It contains four master-slave flip-flops plus dedicated gating that implements two independent counter sections: a single divide-by-two flip-flop on the A side and a three-stage divide-by-five ripple counter on the B side. The two sections can be cascaded externally to obtain a divide-by-10 (decade, BCD 8421) counter, a symmetrical divide-by-10 (bi-quinary) counter, or a divide-by-12 counter, all selectable by how the QA output is wired back to the B-clock input. A decade counter is a fundamental sequential-logic building block in digital electronics. Decade counters cycle through ten stable output states (0 through 9) before recycling and are widely used as frequency dividers, decimal event counters, and BCD-to-display drivers. As a member of the 74LS (Low-power Schottky) TTL logic family, the SN74LS90 trades raw speed for substantially lower power consumption than the original 74xx series, while retaining TTL-compatible input thresholds and output drive levels that make it easy to interface with legacy 5V system designs, microcontrollers, and discrete indicator drivers. Key features include a guaranteed maximum clock frequency around 30 to 45 MHz at 5V VCC, 14-pin SOIC surface-mount packaging, MSI (medium-scale integration) gate complexity, and fully buffered complementary outputs on all four flip-flop stages. The part operates from a single 4.75V to 5.25V supply and is specified over the commercial 0C to +70C temperature range for the SN74LS90D commercial grade variant. Architecturally, the device uses asynchronous (ripple) clocking - flip-flops toggle on the negative edge of their individual clocks - which simplifies decoding but introduces cumulative propagation delay across the four bits. Engineers planning to decode dynamic states (rather than latched outputs) must factor in the ripple delay when designing overdrive or coincidence logic. Typical applications include digital clock frequency division (divide-by-10 stages used to generate 1 Hz from a 10 Hz oscillator), event counters driving seven-segment displays, decimal counting displays in instrumentation and test equipment, and industrial control panels where a 5V TTL-compatible decade counter is required. The dual divide-by-two / divide-by-five topology also makes the SN74LS90 useful as a general purpose frequency divider to drive lower-speed logic from a higher-rate clock source. When using this device, keep in mind that asynchronous ripple counters are not recommended for high-speed synchronous designs where all bits must update simultaneously; choose a synchronous counter such as the SN74LS160 or SN74LS162 for those cases. Decoupling VCC with a 0.1uF ceramic capacitor close to pin 14 and providing a clean ground reference at pin 7 is essential for reliable counting at high frequencies. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. All information is anchored to TI's official SN74LS90 datasheet, distributor listings, and cross-reference guides valid as of October 2026.

RFC Hubungi kami
SN74LS90DR - Decade Counter, 4-Bit, LS-TTL, 14-SOIC | Texas Instruments (Tape & Reel)
SN74LS90DR

SN74LS90DR - Decade Counter, 4-Bit, LS-TTL, 14-SOIC | Texas Instruments (Tape & Reel)

The Texas Instruments SN74LS90DR is a monolithic 4-bit asynchronous decade counter built using low-power Schottky TTL (LS-TTL) technology, supplied in a 14-pin SOIC (D) package. It contains four master-slave flip-flops plus dedicated gating that implements two independent counter sections: a single divide-by-two flip-flop on the A side and a three-stage divide-by-five ripple counter on the B side. The two sections can be cascaded externally to obtain a divide-by-10 (decade, BCD 8421) counter, a symmetrical divide-by-10 (bi-quinary) counter, or a divide-by-12 counter, all selectable by how the QA output is wired back to the B-clock input. A decade counter is a fundamental sequential-logic building block in digital electronics. Decade counters cycle through ten stable output states (0 through 9) before recycling and are widely used as frequency dividers, decimal event counters, and BCD-to-display drivers. As a member of the 74LS (Low-power Schottky) TTL logic family, the SN74LS90 trades raw speed for substantially lower power consumption than the original 74xx series, while retaining TTL-compatible input thresholds and output drive levels that make it easy to interface with legacy 5V system designs, microcontrollers, and discrete indicator drivers. Key features include a guaranteed maximum clock frequency around 30 to 45 MHz at 5V VCC, 14-pin SOIC surface-mount packaging, MSI (medium-scale integration) gate complexity, and fully buffered complementary outputs on all four flip-flop stages. The part operates from a single 4.75V to 5.25V supply and is specified over the commercial 0C to +70C temperature range for the SN74LS90DR commercial grade variant. Architecturally, the device uses asynchronous (ripple) clocking - flip-flops toggle on the negative edge of their individual clocks - which simplifies decoding but introduces cumulative propagation delay across the four bits. Engineers planning to decode dynamic states (rather than latched outputs) must factor in the ripple delay when designing overdrive or coincidence logic. Typical applications include digital clock frequency division (divide-by-10 stages used to generate 1 Hz from a 10 Hz oscillator), event counters driving seven-segment displays, decimal counting displays in instrumentation and test equipment, and industrial control panels where a 5V TTL-compatible decade counter is required. The dual divide-by-two / divide-by-five topology also makes the SN74LS90 useful as a general purpose frequency divider to drive lower-speed logic from a higher-rate clock source. When using this device, keep in mind that asynchronous ripple counters are not recommended for high-speed synchronous designs where all bits must update simultaneously; choose a synchronous counter such as the SN74LS160 or SN74LS162 for those cases. Decoupling VCC with a 0.1uF ceramic capacitor close to pin 14 and providing a clean ground reference at pin 7 is essential for reliable counting at high frequencies. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. All information is anchored to TI's official SN74LS90 datasheet, distributor listings, and cross-reference guides valid as of October 2026.

RFC Hubungi kami
SN74LS90N - 4-Bit Decade Counter | Texas Instruments
SN74LS90N

SN74LS90N - 4-Bit Decade Counter | Texas Instruments

Texas Instruments SN74LS90N is a 4-bit decade counter with asynchronous, negative-edge-triggered operation, TTL logic compatibility, and a 14-pin PDIP package. It divides the input clock by two and provides a three-stage binary count sequence whose overall division ratio is five for the 74LS90 family. The four internal master-slave flip-flops and gating logic allow the counter to be configured for decade-counter operation or other counting sequences required by digital control systems. A decade counter is a synchronous-state counter built from flip-flops and logic gates. In the broader electronics hierarchy, a decade counter belongs to counter logic, digital logic ICs, logic ICs, and ultimately semiconductor devices. It is commonly used to divide one input frequency into lower, predictable frequencies or to produce a modulo-10 counting sequence for timing and control functions. The SN74LS90N provides a 4-bit counter element, negative-edge triggering, and upward counting. Its TTL-compatible interface allows it to operate with other 74LS-family digital logic in established industrial control, instrumentation, and legacy computer systems. Because its counting architecture includes independently controlled sections, designers can also use it in divide-by-five, divide-by-six, divide-by-eight, and related applications depending on the selected output connections. Technically, the monolithic counter combines four master-slave flip-flops with additional gating logic. The master-slave arrangement helps prevent race-through conditions when the clock changes state, while negative-edge triggering defines exactly when the stored count advances. Designers should still account for propagation delay, setup and hold requirements, and output transition behavior when operating near the device’s maximum clock frequency. Typical uses include digital timing references, industrial sequence counters, frequency-divider circuits, test equipment, and embedded legacy control systems. The SN74LS90N is especially appropriate when an existing board requires a standard 14-pin TTL counter rather than a programmable modern counter. Availability and lifecycle decisions should be based on current distributor inventory because legacy through-hole logic sourcing can vary. The primary design consideration is timing margin. Confirm the selected output’s transition timing against the load and the next device’s setup requirement, and route the clock to minimize ringing. Decoupling close to the supply pins and careful grounding remain necessary because every counter edge can propagate supply and ground disturbance into adjacent logic. This page combines verified manufacturer and distributor information, package details, pricing context, sourcing guidance, and verified drop-in alternatives. It also distinguishes documented facts from parameters that still require confirmation from the manufacturer datasheet, helping engineers avoid unsupported assumptions during legacy-logic maintenance and redesign.

RFC Hubungi kami