Produk (44,000+)

TJA1052IT/2518 - Isolated High-Speed CAN Transceiver | NXP
TJA1052IT/2518

TJA1052IT/2518 - Isolated High-Speed CAN Transceiver | NXP

NXP Semiconductors TJA1052IT/2518 is a galvanically isolated, high-speed Controller Area Network transceiver in a 16-pin SO package. It provides the physical-layer interface between a CAN protocol controller and the two-wire CAN bus, with isolation intended to separate high-voltage and low-voltage portions of electric-vehicle and hybrid-electric-vehicle systems. A CAN transceiver is an interface IC within the broader controller-area network communication hierarchy. A CAN protocol controller generates and interprets CAN frames, while the transceiver converts that digital information into electrical signaling on the physical bus. Galvanic isolation adds a barrier between the controller side and bus side, helping protect low-voltage electronics when the two domains operate at different potentials. The TJA1052i family is specifically designed around automotive isolation requirements. Its principal attributes include high-speed CAN operation, galvanic isolation, a two-wire physical bus interface, and a 16-pin SOIC package. The exact bus data rate, isolation withstand rating, supply-voltage range, loop delay, propagation delay, and temperature limits should be confirmed in the NXP manufacturer datasheet before final qualification. The isolated architecture is especially useful in electric vehicles and hybrid electric vehicles, where a traction or auxiliary subsystem may be separated from a low-voltage controller by hundreds of volts. Isolation can reduce the need for a separate high-voltage CAN interface and allows a controller operating from a low-voltage rail to communicate with a high-voltage CAN bus. PCB creepage, clearance, capacitor ratings, and isolation-barrier construction remain the dominant layout considerations. Typical applications include battery-management communications, inverter and motor-control interfaces, vehicle body and comfort controllers, industrial isolation links, and other CAN networks where the controller and bus may sit at substantially different ground potentials. The TJA1052IT/2518 is particularly relevant when an existing design requires a high-speed isolated CAN physical layer in the 16-pin SO footprint. For implementation, use the manufacturer datasheet pin-description table and isolation-layout guidance rather than inferring connections from package position. Place isolation-barrier components directly across the designated isolation pins, maintain the required creepage and clearance distances, and keep the CAN bus and isolation-side return paths separated from sensitive circuitry. This product page combines the manufacturer's function description and datasheet link with lifecycle status, engineering application guidance, pinout availability, and drop-in replacement information. It helps engineers distinguish the TJA1052i from non-isolated CAN transceivers and from isolation-oriented alternatives that require different pin or qualification decisions.

RFC Hubungi kami
TJA1052IT/2Y - Isolated High-Speed CAN Transceiver | NXP
TJA1052IT-2Y

TJA1052IT/2Y - Isolated High-Speed CAN Transceiver | NXP

The NXP TJA1052IT/2Y is a galvanically isolated high-speed CAN (Controller Area Network) transceiver that provides a 2.5 kVrms isolated interface between a CAN protocol controller and the physical two-wire CAN bus, housed in a 16-pin SO (SOIC-16, 300 mil) package with capacitive (galvanic) isolation integrated on-chip. The device operates from a 3 V to 5.25 V supply on the logic/microcontroller side and supports a CAN data rate of up to 5 Mbps, making it suitable for Classic CAN and CAN FD frame formats. The integrated isolation removes the need for an external digital isolator + isolated DC-DC combination in many designs, reducing BOM count and PCB area. What is an isolated CAN transceiver? A CAN transceiver is the physical-layer bridge between a CAN controller (typically embedded in a microcontroller) and the differential CAN bus lines (CANH/CANL). A galvanically isolated version inserts a high-voltage barrier - here implemented via on-chip capacitive coupling - between the logic domain and the bus domain, breaking ground loops and protecting low-voltage MCU I/O from high-voltage transients common in automotive 12 V/24 V powertrain systems and industrial installations. Key features of the TJA1052IT/2Y include 1/1 unidirectional channel count, 2.5 kVrms isolation voltage rating, 5 Mbps maximum data rate, a standby mode for low quiescent current, and compatibility with 1.8 V and 3.3 V controller logic via separate VIO/VCC rails. The device is specifically targeted at Electric Vehicles (EV), Hybrid Electric Vehicles (HEV), and other automotive applications where high-speed CAN communication must coexist with high-voltage battery and inverter systems. Typical applications include EV/HEV battery management system (BMS) communication gateways, on-board chargers (OBC), traction inverter CAN interfaces, industrial CAN bus nodes requiring reinforced insulation, and isolated debug or service interfaces for automotive ECUs. When designing with the TJA1052IT/2Y, engineers should provide local decoupling on both the logic-side and bus-side supplies, observe creepage/clearance for the 2.5 kV isolation barrier, and verify the standby-mode behavior against the system power-state diagram. This page synthesizes distributor pricing, drop-in alternatives, and practical isolation-layout design notes not consolidated in the standalone manufacturer datasheet.

RFC Hubungi kami
TJA1052IT/5 - Isolated 5 Mbps CAN Transceiver | NXP
TJA1052IT/5

TJA1052IT/5 - Isolated 5 Mbps CAN Transceiver | NXP

The NXP TJA1052IT/5 is a galvanically isolated, high-speed CAN transceiver operating at up to 5 Mbps in a 16-lead SOIC package. It provides a 1-transceiver, 1-receiver CAN interface with a 3 V to 5.25 V supply range, matching the logic levels commonly used by CAN controllers, microcontrollers, industrial automation equipment, electric vehicles, and hybrid electric vehicles. A CAN transceiver is the physical-layer component that converts logic-level TXD and RXD signals into differential CAN bus signals, while receiving bus data and returning it as a logic-level RXD output. Galvanic isolation places a signal barrier between the CAN controller side and the two-wire CAN bus side. This helps protect the controller from ground-potential differences and electrical stress encountered in automotive and industrial installations. The TJA1052IT/5 supports CAN data rates up to 5 Mbps and operates from a 3 V to 5.25 V supply. NXP identifies the device as an active high-speed CAN transceiver, and distributor listings describe it as a 1-transceiver, 1-receiver isolated half-CAN interface in a 16-pin SOIC package. Its operating temperature and automotive-qualification details should be confirmed against the specific orderable part number and the manufacturer datasheet before production release. The part is especially relevant to electric and hybrid electric vehicle platforms, where a CAN controller must communicate with powertrain, battery-management, charger, and thermal-management subsystems. Industrial applications include motor drives, robotics, factory automation, and distributed control networks operating on long cable runs. Design layouts should follow the manufacturer’s recommended application circuit, including the prescribed bus termination, common-mode choke, and split capacitor network where applicable. Keep CANH and CANL routing symmetric and controlled, provide solid ground-plane continuity, and avoid placing sensitive analog or high-speed digital traces parallel to the differential bus. Confirm the isolation barrier treatment, maximum bus length, node count, and stub geometry for the target network. This page consolidates verified NXP product information, package and speed details, drop-in replacement candidates, comparison parameters, and practical CAN layout guidance to support component selection and PCB implementation.

RFC Hubungi kami
TJA1053T/N1 - 5V Automotive CAN Transceiver | NXP
TJA1053T/N1

TJA1053T/N1 - 5V Automotive CAN Transceiver | NXP

The NXP TJA1053T/N1 is a half CANbus transceiver for Controller Area Network communication, designed for a 4.75 V to 5.25 V supply range in a 14-pin SO package. Its interface pins tolerate voltages up to 36 V, supporting its use in automotive electrical environments when the surrounding circuitry provides the required protection and signal compatibility. The device combines a CAN transmitter and CAN receiver in one interface IC, providing the physical-layer connection between a CAN controller and the differential CAN bus. A CAN transceiver is an interface IC within the broader Controller Area Network hierarchy. It converts logic-level data into a differential bus signal at the transmitter and reconstructs a logic-level signal from the bus at the receiver. This physical-layer function allows a microcontroller, automotive control unit, or industrial controller to exchange reliable data over a multi-node CAN network without implementing the electrical interface directly. The TJA1053T/N1 operates from a nominal 5 V supply, with the documented operating range extending from 4.75 V to 5.25 V. Its I/O pins are tolerant to voltages as high as 36 V, an important consideration for 12 V automotive systems. The 14-SO package provides a compact surface-mount footprint suitable for automotive and industrial control equipment where PCB area is limited. The principal design benefit is the combination of a 5 V transceiver interface with high-side I/O tolerance. Logic-side circuitry can operate from the regulated 5 V rail, while the CAN interface remains capable of withstanding the voltage excursions commonly encountered in vehicle electrical systems. The tolerance rating does not remove the need for correct transceiver placement, bus termination, decoupling, and protection strategy. Typical uses include automotive body and comfort modules, engine controllers, instrument clusters, industrial automation equipment, CAN gateways, and embedded control systems. The device is particularly appropriate when the controller uses a 5 V supply and the CAN bus interface must tolerate the electrical environment associated with automotive wiring harnesses. When laying out a board, place the transceiver close to the CAN connector and route TXD and RXD as short traces away from high-current switching nodes. Terminate the bus at both physical ends with the resistance specified by the CAN network design. Follow the pin-description table and application guidance in the manufacturer datasheet before assigning PCB tracks, supply bypass capacitors, or bus protection components. This page consolidates the available manufacturer and distributor information with practical design guidance, package details, sourcing answers, and documented compatibility information. It helps engineers identify the correct CAN transceiver without confusing high-side I/O tolerance with immunity to arbitrary bus faults or eliminating the external protection required in automotive wiring.

RFC Hubungi kami
TJA1054AT - Fault-Tolerant 125 kBd CAN Transceiver | NXP
TJA1054AT

TJA1054AT - Fault-Tolerant 125 kBd CAN Transceiver | NXP

NXP Semiconductors TJA1054AT is a fault-tolerant Controller Area Network transceiver intended for low-speed, single-wire CAN communication up to 125 kBd, supplied in a 14-pin SOIC package. The device sits between a CAN protocol controller and the physical bus wiring, providing the interface required to transmit and receive CAN signals while adding protection against faults on the bus. A CAN transceiver is the physical-layer component between a digital CAN controller and its bus wiring. The controller processes frames and protocol functions, while the transceiver converts logical controller signals into electrical bus signals and presents received bus information to the controller. A single-wire CAN interface uses one signal line for communication and normally requires a return path through the vehicle or equipment ground structure. The TJA1054AT is therefore positioned within the hierarchy of CAN interface IC, network interface, communications semiconductor, and integrated circuit. The TJA1054AT provides operation up to 125 kBd and is identified as a fault-tolerant CAN transceiver. The TJA1054A family is an electrostatic-discharge-improved version of the original TJA1054. NXP states that the TJA1054AT is pin and downward compatible with the PCA82C252T and TJA1053T, allowing those devices to be replaced while retaining their functions. Its SO14 package is a surface-mount package suitable for conventional automotive and industrial controller-board layouts. The principal design benefit is fault tolerance in environments where a CAN conductor may be exposed to wiring faults. Its 125 kBd maximum intended data rate supports low-speed CAN networks in passenger-car systems and other cost-sensitive embedded networks. A design must still observe the transceiver's detailed operating limits, bus topology, termination strategy, supply requirements, and external protection requirements defined by the manufacturer datasheet. Typical uses include body and comfort-control modules, passenger-car diagnostic equipment, low-speed automotive gateways, industrial control panels, and embedded CAN controllers. The device is most appropriate where a single-wire bus and fault-resilient physical interface are required. It should not be confused with differential two-wire CAN transceivers, which use separate CANH and CANL conductors. For PCB implementation, use the exact pin numbering and pin descriptions in the NXP data sheet, place the transceiver close to the connector or bus routing, and keep the CAN trace away from high-current switching paths. Confirm bus polarity, ground reference, decoupling, and any required external components during schematic review. This page adds lifecycle context, documented replacement relationships, package-level comparison, and practical design guidance around the TJA1054AT. Because NXP identifies the part as end of life, engineers should validate supply continuity, approved lifecycle status, and a complete sourcing plan before committing a new production design to this device.

RFC Hubungi kami
TJA1054AT/N - Fault-Tolerant Low-Speed CAN Transceiver | NXP
TJA1054AT/N

TJA1054AT/N - Fault-Tolerant Low-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1054AT/N is a fault-tolerant Controller Area Network transceiver designed for low-speed CAN communication up to 125 kBd, particularly in passenger-car networks. It is an interface between a CAN protocol controller and the physical CAN bus conductors, and it is housed in a 14-pin SO package. The TJA1054A family is an electrostatic-discharge-improved implementation of the TJA1054. A CAN transceiver is an interface IC that connects a digital CAN controller to a physical bus. Unlike ordinary two-wire differential CAN, the fault-tolerant architecture used by the TJA1054A is intended for low-speed in-vehicle networks and adds local wake-up and bus-fault handling functions. Within the product hierarchy, the TJA1054AT/N is a CAN transceiver, an interface IC, and a semiconductor designed for automotive communication networks. The main feature of the TJA1054AT/N is its ability to replace the PCA82C252T and TJA1053T while retaining their functions because it is pin and downwards compatible with those devices. The TJA1054AT is likewise compatible with the TJA1054T. Its fault-tolerant CAN interface is intended for data rates up to 125 kBd, while the ESD-improved TJA1054A design strengthens its suitability for electrically demanding vehicle networks. The device also provides local wake-up support through the WAKE pin. According to the NXP TJA1054 documentation, a local wake-up request is detected through an edge followed by a qualifying level exceeding the specified wake-up interval. The transceiver can then assert its INH output high to activate an external supply regulator. This feature is useful in distributed vehicle systems where a node must awaken a local subsystem without waking the entire network. Typical applications include passenger-car low-speed CAN networks, body and comfort systems, door modules, seat controllers, lighting controllers, climate-control interfaces, and other automotive ECUs connected by low-speed CAN. The TJA1054AT/N is most appropriate when the system specifically requires a fault-tolerant single-wire CAN physical layer and does not require the high-speed differential CAN architecture used by many newer vehicle platforms. When designing a replacement around this device, verify the physical footprint, exposed functionality, and bus topology. Although the NXP product information identifies compatibility with the PCA82C252T and TJA1053T, a replacement should still be checked for system-level differences in wake-up behavior, supply operation, bus termination, and application timing. Use the manufacturer's pin-description table when assigning PCB nets and the recommended application circuit when selecting external components. This page combines the confirmed NXP product information, manufacturer datasheet links, package details, compatibility statements, and application guidance. It also organizes practical design considerations and direct replacement questions so engineers can assess the TJA1054AT/N against its documented drop-in-compatible predecessors without confusing low-speed fault-tolerant CAN with high-speed differential CAN.

RFC Hubungi kami
TJA1054T/N1 - Fault-Tolerant 125 kBd CAN | NXP
TJA1054T/N1

TJA1054T/N1 - Fault-Tolerant 125 kBd CAN | NXP

The NXP Semiconductors TJA1054T/N1 is a fault-tolerant Controller Area Network transceiver designed for low-speed CAN communication up to 125 kBd in passenger-car applications. It provides the physical-layer interface between a CAN protocol controller and the CANH and CANL bus conductors, and the device is packaged in an 14-pin small-outline SOIC package. Its fault-tolerant architecture is intended for communication links where reliable operation during bus faults is important. A CAN transceiver is an interface IC within the wider network-interface and semiconductor hierarchy. It converts logic-level transmit and receive signals from a CAN controller into the physical differential signaling used on a CAN bus. CAN itself is a deterministic, multiplexed communication network used in automotive and industrial control systems. The TJA1054T/N1 occupies the physical-layer position between digital processing circuitry and the two-wire bus. The TJA1054T/N1 is identified as a fault-tolerant CAN transceiver and is primarily intended for low-speed networks operating at up to 125 kBd. NXP states that the device is pin-compatible and downwards-compatible with the PCA82C252T and TJA1053T, allowing either device to be replaced while retaining the existing functions. This compatibility makes the TJA1054T a practical upgrade path for designs already using those interface devices. The principal engineering benefit is bus-fault tolerance. NXP describes very low electromagnetic emission as an important improvement over the PCA82C252 and TJA1053T, based on strong matching between the CANH and CANL outputs. Good matching helps limit differential-mode emissions and improves signal quality on the physical bus. The TJA1054 family also retains the functional structure expected by existing CAN controllers, allowing a PCB-level replacement without changing the surrounding bus interface. Typical uses include passenger-car body and comfort networks, low-speed automotive CAN subnets, sensor and actuator gateways, and industrial equipment that retains an automotive CAN architecture. In these systems, the transceiver connects a CAN controller to CANH and CANL, provides bus-side transmit and receive functions, and helps the network continue operating correctly when the bus is shorted to ground, shorted to supply, or open. Exact protection and operating details should be confirmed in the manufacturer datasheet. PCB implementation should preserve the device's pin compatibility with the PCA82C252T and TJA1053T, including the same 14-pin SOIC footprint and signal assignments. Check the bus-polarity, supply, ground, transceiver-mode, and controller-interface connections against the NXP pin description before fabrication. Do not assume that all CAN transceivers are interchangeable merely because they use the same protocol; interface voltage, mode-control logic, and fault behavior must also match. This product page combines the manufacturer compatibility information, package identification, available ordering references, and practical replacement guidance in one engineering-focused record. It also distinguishes verified drop-in choices from options that require package or function review, helping engineers evaluate a CAN bus update without relying on an incomplete cross-reference list.

RFC Hubungi kami
TJA1055T - 125 kBd Fault-Tolerant CAN Transceiver | NXP | SOIC-14
TJA1055T

TJA1055T - 125 kBd Fault-Tolerant CAN Transceiver | NXP | SOIC-14

The NXP Semiconductors TJA1055T is an enhanced fault-tolerant CAN transceiver that interfaces a CAN protocol controller with the physical CANH and CANL bus wires, intended for low-speed in-vehicle communication up to 125 kBd in passenger cars, and it is supplied in a 14-pin SOIC (SOP-14) surface-mount package. A CAN transceiver is the physical-layer device in a Controller Area Network link. It sits between the CAN protocol controller inside a microcontroller and the differential bus wiring, converting controller logic levels into balanced bus-line signals and, in the opposite direction, converting received bus states into a clean logic-level receive output. In the classification hierarchy it is an interface IC, specifically a CAN interface or CAN bus transceiver, a member of the broader transceiver and interface IC family used in automotive and industrial communication networks. Key features of the TJA1055T include its enhanced fault-tolerant bus-line interface, its optimization for low-speed in-car communication, and its pin-to-pin compatibility with the earlier TJA1054 and TJA1054A devices, which allows an upgrade of an existing design without a board change. The fault-tolerant architecture is the defining improvement over the predecessor family, adding protection against faults that occur on the bus lines during operation. Technically, the device operates with the standard differential CAN signalling scheme in which the two bus lines are dominant and recessive states rather than fixed levels. Because the TJA1055T is specified for low-speed networks up to 125 kBd, it is intended for body, comfort and convenience sub-networks rather than for powertrain or chassis high-speed CAN links, where devices rated for 1 Mbit/s or more are normally chosen. The 14-pin SOIC package is a standard surface-mount footprint that simplifies assembly and rework in automotive electronics manufacturing. Typical applications include body control units, door and seat modules, climate control units, window and lighting controllers, passenger-comfort CAN sub-networks, vehicle diagnostic interfaces, low-speed CAN gateways for industrial and building systems, and CAN bus test and monitoring equipment. When laying out the design, place the transceiver close to the bus connector, keep the CANH and CANL traces short and matched, provide the required bus termination resistors at the physical ends of the segment, and decouple the supply pins close to the device to limit conducted noise on the bus. Confirm that the transceiver variant selected matches the supply and bus configuration of the target network before releasing the layout. This page consolidates the manufacturer description, verified distributor listings, drop-in replacement candidates and practical integration guidance for the TJA1055T in one place, so engineers can qualify the part and plan a sourcing strategy without searching through multiple listings and cross-reference tools.

RFC Hubungi kami
TJA1055T/1J - 125 kBd Fault-Tolerant CAN Transceiver
TJA1055T/1J

TJA1055T/1J - 125 kBd Fault-Tolerant CAN Transceiver

NXP Semiconductors TJA1055T/1J is an enhanced fault-tolerant Controller Area Network transceiver for low-speed data links up to 125 kBd. It operates from a 4.75 V to 5.25 V supply and is packaged in a 14-pin SOIC for surface-mount assembly. The device connects a CAN protocol controller to the physical CANH and CANL bus conductors while providing differential transmit, receive, and fault-tolerance functions. A CAN transceiver is the physical-layer interface between a digital CAN controller and the wired CAN network. The TJA1055 family belongs to the interface-IC hierarchy and is specifically optimized for in-car low-speed communication, where its 125 kBd target complements higher-speed CAN controller and transceiver families. Its enhanced fault tolerance helps maintain operation when the bus is shorted to ground, shorted to the supply, or open-circuit, subject to the detailed protection and operating conditions stated by NXP. Key verified characteristics include a 125 kBd low-speed CAN application target, a 4.75 V minimum supply, a 5.25 V maximum supply, and a 14-pin SOIC package. NXP identifies the TJA1055 as pin-to-pin compatible with the TJA1054 and TJA1054A. Distributor listings also identify TJA1055T/1J as an automotive CAN interface available in tape-and-reel ordering. The transceiver should be placed near the CAN bus connector, with its CANH and CANL pins connected to the protected bus wiring and its TXD and RXD pins connected to the CAN controller. Because the device is intended for passenger-car and other low-speed CAN links, system designers should verify timing, termination, bus topology, logic levels, and protection requirements against the manufacturer datasheet before production release. The TJA1055T/1J is suitable for automotive body electronics, comfort modules, diagnostic equipment, sensor nodes, and other 125 kBd CAN applications. Its principal design consideration is that CAN bus behavior depends on termination, wiring, common-mode conditions, and transceiver protection. A CAN bus should not be treated as a generic communication line; the selected transceiver, controller, and network implementation must be validated together. This page combines verified manufacturer and distributor information, package and ordering details, and application guidance for engineers evaluating a SOIC-14 CAN physical-layer interface.

RFC Hubungi kami
TJA1055T/2Z - 125 kBd Fault-Tolerant CAN Transceiver | NXP
TJA1055T/2Z

TJA1055T/2Z - 125 kBd Fault-Tolerant CAN Transceiver | NXP

The NXP Semiconductors TJA1055T/2Z is an enhanced fault-tolerant Controller Area Network transceiver intended for low-speed automotive applications up to 125 kBd. It provides a physical-layer interface between a CAN protocol controller and the CAN bus conductors, uses a 14-SO package, and is supplied in tape-and-reel packaging. According to the NXP product information, its budgetary price is $1.15 USD at a quantity of 1,000 and its indicated lead time is 10 weeks. A CAN transceiver is an interface IC that connects a host controller to a differential CAN network. It belongs to the communication interface hierarchy: CAN transceiver > bus transceiver > interface IC > semiconductor. Unlike a generic transceiver, this device is designed around the electrical behavior and fault tolerance requirements of low-speed CAN systems, where dependable operation during wiring faults and disturbed bus conditions is important. Key documented features include enhanced fault-tolerant CAN operation, support for data rates up to 125 kBd, and use in passenger-car CAN networks. The verified distributor records also identify the device as a one-channel, half CAN-bus transceiver in a 14-SO package. The NXP product page identifies TJA1055T as active and lists reel-reel packing with a minimum package quantity and minimum order quantity of 2,500 pieces. The TJA1055T/2Z performs the physical signaling required between the CAN controller and the bus while providing the fault-tolerance behavior expected in automotive environments. Its use of a dedicated bus interface allows the controller to send and receive frames without implementing analog bus-level signaling directly. Detailed thresholds, loopback behavior, supply current, and absolute maximum ratings remain [DATA_NEEDED: complete electrical characteristics] because they were not included in the supplied verified records. Typical uses include passenger-car body and comfort systems, door modules, climate-control controllers, lighting controllers, instrument clusters, and other low-speed CAN nodes. It is most appropriate where the network operates at 125 kBd or below and the design requires a dedicated high-reliability CAN physical-layer device rather than a general-purpose differential transceiver. When designing a PCB around the TJA1055T/2Z, verify the complete NXP datasheet pinout, transceiver termination requirements, supply decoupling, and bus-fault behavior before layout release. The supplied search records establish the 14-SO package designation but do not expose a verifiable numbered pin table, so this page does not infer pin names or connectivity. Maintain the manufacturer-specified CAN bus topology and provide the required local decoupling and protection appropriate to the vehicle network.

RFC Hubungi kami
TJA1055T/3/1J - 125 kBd Fault-Tolerant CAN Transceiver | NXP
TJA1055T/3/1J

TJA1055T/3/1J - 125 kBd Fault-Tolerant CAN Transceiver | NXP

NXP Semiconductors TJA1055T/3/1J is an enhanced fault-tolerant Controller Area Network transceiver with differential transmit and receive capability, optimized for low-speed CAN communication up to 125 kBd. The device operates from a 5 V to 28 V supply range, includes a 3 V VIO variant for interfacing with low-voltage CAN controllers, and is offered in a 14-pin SO surface-mount tape-and-reel package. It is designed for passenger-car body and comfort electronics where fault tolerance and low-speed in-vehicle networking are important. A CAN transceiver is the physical-layer interface between a CAN protocol controller and the differential CAN bus. It converts controller logic signals into CANH and CANL bus activity and converts differential bus voltage into a receive signal. Positioned within the hierarchy of CAN interface ICs, transceiver ICs, interface ICs, and semiconductors, the TJA1055T provides the electrical interface required to connect digital controllers to a robust in-vehicle communication network. The TJA1055T/3/1J provides operation at data rates up to 125 kBd, differential receive and transmit functions, and sleep or standby operating modes for reduced power consumption. Its supply-voltage coverage supports systems operating from 5 V, 9 V, 12 V, 15 V, 18 V, 24 V, and 28 V environments. The /3 order-code variant provides a 3 V VIO interface, allowing compatibility with controllers or logic domains using a lower supply voltage. The device uses differential bus signaling to provide common-mode rejection and improve robustness against noise found in vehicle electrical environments. Its fault-tolerant design is intended for low-speed CAN networks in passenger cars rather than high-bandwidth automotive Ethernet or high-speed CAN FD systems. The 14-pin SO package supports compact surface-mount assembly while exposing the controller interface, bus interface, power, ground, and control connections required by the device architecture. Typical applications include vehicle body-control modules, door and seat controllers, climate-control interfaces, lighting controllers, comfort systems, and distributed low-speed passenger-car networks. The combination of a 125 kBd maximum data rate, broad supply range, sleep or standby support, and 3 V VIO option makes the TJA1055T/3/1J appropriate where a 3.3 V controller must communicate with a conventional 12 V or 24 V vehicle CAN network. When designing the PCB layout, treat CANH and CANL as a controlled-impedance differential pair routed as symmetrically as practical, with a continuous return path beneath the pair. Keep the transceiver close to the bus connector or bus-header, minimize stub branches, and follow the grounding and decoupling recommendations in the manufacturer datasheet. Component values and layout distances not present in the supplied source extract remain unverified and must be confirmed from the complete NXP datasheet before release. This page consolidates the verified NXP product information, distributor listings, order-code distinctions, and package data for TJA1055T/3/1J. It also distinguishes confirmed drop-in references from unsupported cross-brand equivalents, highlights verified design parameters, and clearly identifies pricing, pin-mapping, and detailed electrical values that still require confirmation.

RFC Hubungi kami
TJA1055T/3/2Z - 125 kbit/s Fault-Tolerant CAN Transceiver | NXP | SO-14
TJA1055T/3/2Z

TJA1055T/3/2Z - 125 kbit/s Fault-Tolerant CAN Transceiver | NXP | SO-14

The NXP Semiconductors TJA1055T/3/2Z is an enhanced fault-tolerant CAN transceiver for low-speed Controller Area Network buses up to 125 kbit/s, packaged in a 14-pin SO (SOIC-14) surface-mount package with an exposed ground-pad-style land pattern. It accepts supply rails of 5 V, 9 V, 12 V, 15 V, 18 V, 24 V and 28 V, and provides a single differential transmit and receive channel (1/1, half duplex) with sleep and standby modes for low-current parked vehicles. A CAN transceiver is the physical-layer interface between a CAN protocol controller and the two-wire differential bus. It converts the controller's logic-level TXD and RXD signals into balanced bus levels, and returns a filtered digital receive signal. The TJA1055 belongs to the fault-tolerant CAN transceiver family, where the bus driver survives shorted-bus and reversed-battery conditions that would damage a conventional high-speed transceiver. Key characteristics include operation up to 125 kbit/s, an enhanced fault-tolerant transmit driver, a receive filter with extended glitch rejection, low-current sleep and standby operating modes, and AEC-Q100 qualification for automotive applications. The device is pin-to-pin compatible with the earlier TJA1054 and TJA1054A, which allows existing low-speed CAN body, comfort and diagnostic modules to be updated without a layout change. Internally the device separates the controller interface from the bus interface so that the bus-side driver can withstand faults independently of the logic side. A dedicated sleep input and internal mode control let a body control module wake the transceiver only when needed, reducing standing current in parked vehicles. The recessive and dominant output levels are defined to suit ISO 11898-2 style low-speed CAN networks. Typical uses include passenger-car door modules, seat and window controllers, climate control panels, body control units, diagnostic connectors, trailer modules and other 125 kbit/s CAN nodes in vehicles, plus industrial equipment that adopts low-speed CAN for cable-cost reduction. When laying out the board, place the bus transceiver close to the connector and keep the CANH and CANL traces short, matched in length and free of stubs, because the twisted pair carries a differential signal whose balance determines noise immunity. The logic-side pins need short traces to the CAN controller and a solid ground reference, since the transceiver converts bus common-mode voltage into a single-ended logic output. This page consolidates manufacturer ratings, package details, drop-in alternatives, application guidance and layout notes so that engineers can evaluate the TJA1055T/3/2Z for a low-speed CAN node without rebuilding the data from multiple sources.

RFC Hubungi kami
TJA1055T/3/C - 125 kBd Fault-Tolerant CAN Transceiver | NXP
TJA1055T/3/C

TJA1055T/3/C - 125 kBd Fault-Tolerant CAN Transceiver | NXP

The NXP Semiconductors TJA1055T/3/C is an enhanced fault-tolerant Controller Area Network transceiver designed for low-speed passenger-car networks operating up to 125 kBd. It provides differential CAN transmit and receive functions and is intended to interface a CAN protocol controller with the physical CANH and CANL bus wires. The device is offered in a 14-pin SO package for surface-mount PCB assembly. A CAN transceiver is the physical-layer interface between a digital protocol controller and a differential CAN bus. It converts controller logic levels into balanced bus signals and reconstructs a valid receive signal from the bus. Within the broader hierarchy, the TJA1055T/3/C is a CAN transceiver, a bus interface IC, an interface circuit, and a semiconductor. Its fault-tolerant design is intended to maintain communication when bus faults or unusual bus conditions occur, making it suitable for automotive body, comfort, and other low-speed distributed systems. The principal documented characteristics include an enhanced fault-tolerant CAN architecture, differential transmission and reception, and operation to 125 kBd. The /3 ordering option is documented in the TJA1055 family as a version with a current source connected to ground for the RTH and RTL pins. Fault-tolerant operation also depends on correctly implementing the resistor network and recessive-state biasing around the transceiver. NXP describes the TJA1055 family as an interface between the CAN protocol controller and physical bus wires in passenger cars. Its architecture supports low-speed CAN communication while adding fault-tolerance improvements relative to earlier transceivers. The /3 variant provides defined current-source behavior for the RTH and RTL pins, which is important when reproducing the reference termination and bias circuit on an existing PCB. Typical uses include passenger-car body-control modules, door and window controllers, seat and climate-control electronics, lighting controllers, instrument-cluster peripherals, and other low-speed CAN nodes. Automotive qualification details, exact transceiver timing limits, and the full electrical limits must be checked against the complete NXP data sheet before a new production design is released. Designers should preserve the established SO-14 footprint and pin assignments when qualifying this device. The termination-bias network, CANH and CANL routing, ground return, and protection components should follow the manufacturer application circuit. Because bus-node behavior depends on both the transceiver and external resistors, changing one network component without checking the complete termination scheme can alter dominant and recessive levels. This product record combines the verified NXP family description, available ordering-code information, package identification, fault-tolerance characteristics, and practical replacement considerations. It also identifies where complete electrical, environmental, qualification, lifecycle, and pin-function details must be taken directly from the NXP documentation or confirmed with the manufacturer before production release.

RFC Hubungi kami
TJA1055T/C - Fault-Tolerant CAN Transceiver | NXP
TJA1055T/C

TJA1055T/C - Fault-Tolerant CAN Transceiver | NXP

The NXP TJA1055T/C is an enhanced fault-tolerant Controller Area Network transceiver intended for low-speed automotive communication at up to 125 kBd. It provides the physical-layer interface between a CAN protocol controller and the CAN bus conductors and is supplied in a 14-pin SO package. The device combines normal CAN transceiver operation with fault-tolerant behavior for passenger-car applications. A CAN transceiver is the physical-layer component between a digital CAN controller and the wired CAN bus. It belongs to the hierarchy of CAN interface ICs, bus transceivers, interface semiconductors, and power-management-independent communication ICs. By converting logic-level TX and RX signals into bus-level signals, and returning bus state to the controller, it separates the network's physical signaling from the controller's data protocol and firmware. The TJA1055 is designed for low-speed CAN networks and emphasizes fault tolerance. NXP identifies the TJA1055T as an enhanced fault-tolerant CAN transceiver, while the TJA1055 family is optimized for in-car low-speed communication. Its principal application is a passenger-car CAN network in which dependable bus operation and tolerance of fault conditions are more important than high-bandwidth communication. The TJA1055 family is also pin-to-pin compatible with the NXP TJA1054 and TJA1054A according to the manufacturer datasheet. This compatibility supports PCB reuse when a design moves from an earlier transceiver generation to the enhanced TJA1055, although engineers should still review the associated CAN controller, bus termination, power-supply, and application requirements before approving a substitution. Typical deployments include body and comfort systems, door modules, climate-control electronics, lighting controllers, seat controls, instrument-cluster peripherals, and other low-speed vehicle networks. The TJA1055T/C can also serve industrial or embedded CAN equipment when the system intentionally operates within the family's low-speed fault-tolerance design point. The protocol controller remains responsible for CAN frames, arbitration, error handling, and higher-layer communication. A robust implementation requires correct transceiver decoupling, a suitable CAN controller interface, and the termination strategy appropriate to the complete bus. The two dominant bus conductors and the return path must be routed as a consistent network, while exposed connector wiring and automotive transients require careful protection planning. Review the manufacturer's application guidance and the completed PCB implementation before production release. This page combines the manufacturer product information, the exact TJA1055T/C ordering information, package and speed data, pin-compatible family alternatives, and practical design guidance. It also distinguishes verified drop-in options from ordering variants that should not be treated as separate engineering alternatives.

RFC Hubungi kami
TJA1057BTK - High-Speed CAN Transceiver | NXP Semiconductors
TJA1057BTK

TJA1057BTK - High-Speed CAN Transceiver | NXP Semiconductors

The NXP Semiconductors TJA1057BTK is a high-speed Controller Area Network (CAN) transceiver from the Mantis family, providing an interface between a CAN protocol controller and the physical two-wire CAN bus in an 8-pin HVSON (3x3 mm) package with exposed pad. It supports data rates up to 5 Mbps (CAN FD capable), operates over a wide supply range of 4.75 V to 5.25 V, and is designed for high-speed CAN applications in the automotive industry. A CAN transceiver (also called a CAN bus driver/receiver) is a physical-layer IC that converts the differential digital signaling of a CAN protocol controller into the differential voltage levels required by the ISO 11898-2 CAN bus standard. It sits between a microcontroller's CAN module and the bus wires (CANH/CANL), providing immunity to common-mode noise and ESD protection. CAN transceivers belong to the broader family of interface ICs and are essential building blocks for in-vehicle networking, industrial automation, and any distributed control system that uses the CAN protocol. The TJA1057BTK delivers differential transmit capability to the bus with controlled slew rate, and differential receive capability with high common-mode rejection. It supports both Normal and Silent operating modes, where Silent mode disables the transmitter for listen-only diagnostics. The device is optimized for low electromagnetic emission (EME) and high electromagnetic immunity (EMI), meeting the stringent automotive requirements for CAN bus communication. Integrated thermal protection, bus dominant time-out, and under-voltage detection on VCC enhance system reliability. The 8-pin HVSON package (3x3 mm) with exposed thermal pad offers a very compact footprint suitable for space-constrained ECUs (Electronic Control Units). The exposed pad provides a low thermal resistance path to the PCB copper, allowing the IC to handle the bus fault conditions specified in ISO 11898-5 without derating. The TJA1057BTK is functionally identical to the TJA1057CT within the SOI3+ process family - they differ only in the VIO supply pin logic level handling. Typical applications include automotive body and comfort ECUs, infotainment CAN interfaces, industrial CAN nodes, building automation, and any embedded system requiring a robust, standardized CAN physical layer. In these use cases, the TJA1057BTK acts as the bus interface between a 3.3 V or 5 V microcontroller's CAN controller and the 12 V automotive CAN bus. A key design consideration is the bus termination: a 120 Ω resistor (or split 60 Ω + 60 Ω with capacitor) must be present at each end of the CAN bus segment. The HVSON exposed pad must be soldered to a copper pad of at least 1 mm² to ensure proper thermal performance under continuous bus fault conditions. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. The information gain comes from a structured cross-reference analysis combining the TJA1057 datasheet family, the obsolescence brief on TJA1050 replacements, and verified distributor stock data as of 2026-10-16.

RFC Hubungi kami
TJA1057BTK-0J - 5Mbps CAN FD Transceiver, HVSON-8 | NXP
TJA1057BTK-0J

TJA1057BTK-0J - 5Mbps CAN FD Transceiver, HVSON-8 | NXP

The NXP TJA1057BTK-0J is a high-speed CAN (Controller Area Network) transceiver from the Mantis family, providing an interface between a CAN protocol controller and the physical two-wire CAN bus. Housed in an 8-pin HVSON (3x3 mm) package with exposed pad, it supports data rates up to 5 Mbps and is qualified to AEC-Q100 Grade 1 for automotive applications. A CAN transceiver (also called a CAN bus transceiver or CAN interface IC) is a physical-layer device that converts the digital transmit/receive logic signals of a CAN protocol controller inside a microcontroller into the differential CANH/CANL bus signals required on the actual network. CAN belongs to the broader category of serial communication interface ICs, alongside RS-485, RS-232 and LIN transceivers. The TJA1057 family specifically targets high-speed classical CAN and CAN FD (Flexible Data-rate) networks used for powertrain, chassis and body electronics. Key features include a low electromagnetic emission (EME) common-mode choke design, high electromagnetic immunity (EMS), a low-power Standby mode with remote wake-up capability, and ±8 kV HBM ESD protection on the bus pins (per IEC 61000-4-2 on the bus pins, per datasheet). The transceiver operates from a 4.5 V to 5.5 V VCC supply, supports bus voltages from -27 V to +40 V, and provides a TxD dominant time-out for fail-safe behavior. The TJA1057BTK/0J variant carries the 'B' suffix (VIO supply pin present, allowing direct level-shifting to MCUs at 3.3 V or 5 V) and the 'TK' suffix indicating the 8-pin HVSON package with exposed pad. The /0J suffix designates the production ordering code (tape-and-reel packaging). Internally, the device uses a silicon-on-insulator (SOI) process (NXP SOI3+ family), which gives it excellent ESD and latch-up immunity versus older bulk-silicon CAN transceivers like the TJA1050. Typical applications include automotive body control modules (BCMs), gateway ECUs, instrument clusters, HVAC control units, transmission ECUs and industrial CAN nodes operating up to 1 Mbit/s in classical CAN or 5 Mbps in CAN FD networks. The transceiver interfaces directly to NXP S32K and most third-party automotive MCUs. When designing with this part, place the VCC decoupling capacitor (typically 100 nF) directly adjacent to pin 8 and connect the exposed pad (pin 0) to a large PCB ground plane for thermal dissipation and low-impedance return paths. Match the CANH/CANL bus termination to 120 Ω at the network ends to satisfy ISO 11898-2 and avoid signal-integrity issues at high bus loads.

RFC Hubungi kami
TJA1057GT/1Z - High-Speed CAN Transceiver SOIC-8 | NXP
TJA1057GT/1Z

TJA1057GT/1Z - High-Speed CAN Transceiver SOIC-8 | NXP

The NXP TJA1057GT/1Z is a high-speed CAN (Controller Area Network) transceiver from the Mantis family, providing an interface between a CAN protocol controller and the physical two-wire CAN bus, housed in an 8-pin SOIC (SO-8) package. Key specifications include ISO 11898-2:2016 conformance, data rates up to 1 Mbit/s on the TJA1057T variant with CAN FD support on other variants, and automotive-grade temperature operation. What is a CAN transceiver? A CAN transceiver is a physical-layer interface IC that converts digital transmit/receive logic signals from a microcontroller CAN controller into differential voltage signals on a two-wire CAN bus (CANH and CANL). It belongs to the hierarchy: CAN transceiver -> CAN interface IC -> Interface ICs -> Integrated Circuits. The transceiver also provides bus protection, fault tolerance (dominant/recessive clamping, TXD dominant time-out), and EMC/ESD robustness required in automotive environments. Key features of the TJA1057 include very low current consumption in standby and go-to-sleep modes with remote wake-up capability, an integrated VIO supply pin on /3 variants for direct interfacing with 3.3V and 5V microcontrollers, and an undervoltage detection on VCC and VIO supplies. The TJA1057 implements the CAN physical layer per ISO 11898-2:2016 and SAE J2284-1 to SAE J2284-5, with the TJA1057T explicitly specified for data rates up to 1 Mbit/s. Architecturally, the device uses a differential transmit/receive path with slope control for low-EMI operation, an internal LDO for digital supply, and a sophisticated thermal protection scheme. Its split-pin output stage balances common-mode stability with low electromagnetic emissions, making it well-suited for automotive body, chassis, and powertrain networks. Typical applications include automotive body control modules, gateway ECUs, infotainment CAN nodes, industrial CAN automation nodes, and CAN-FD enabled instrument clusters. Its robustness against ESD (>6 kV HBM) and bus fault voltages (±58 V) makes it dependable in harsh electrical environments. When designing with this device, ensure proper bus termination with 120 ohm resistors at each end of the bus and a common-mode choke for EMI-sensitive applications. The TJA1057 requires careful placement of the VCC decoupling capacitor close to pin 1 to maintain supply stability during dominant-to-recessive transitions. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami
TJA1057GT/3J - 1 Mbit/s CAN Transceiver | NXP Semiconductors
TJA1057GT/3J

TJA1057GT/3J - 1 Mbit/s CAN Transceiver | NXP Semiconductors

The NXP Semiconductors TJA1057GT/3J is a high-speed CAN bus transceiver with differential transmit and receive capability, support for CAN data rates up to 1 Mbit/s, and a VIO input for direct interfacing with 3.3 V or 5 V microcontrollers. It is supplied in an 8-pin SOIC package. The device connects a CAN protocol controller to a physical two-wire CAN bus in automotive and industrial communication systems. A CAN transceiver is a physical-layer interface IC that converts logic-level controller signals into differential bus signals and converts received differential signals back into logic-level data. The TJA1057 belongs to NXP's Mantis family of CAN transceivers, placing it within the hierarchy of CAN interface IC, communication transceiver, interface IC, and semiconductor. Its high-speed differential operation allows a CAN controller and transceiver combination to communicate over a noisy wiring harness while preserving signal integrity. The principal feature of the /3 variant is its dedicated VIO supply connection. According to the manufacturer documentation, VIO should be connected to the microcontroller supply voltage, allowing the TXD and RXD interface levels to be adjusted for either 3.3 V or 5 V operation. This helps avoid unnecessary voltage-level conversion between the CAN controller and the physical bus transceiver. The TJA1057 family implements the CAN physical layer defined by ISO 11898-2:2016 and the SAE J2284-1 through J2284-5 specifications. TJA1057GT/3J provides one CAN channel and uses an 8-pin SOIC footprint identified as PDSO8 in distributor data. Its architecture separates the controller-facing digital interface from the differential CANH and CANL bus connection. The VIO domain supports integration with modern microcontrollers, while the bus side handles the higher-voltage signaling required by a wired CAN network. This division of voltage domains is central to correct PCB design because input, output, transceiver, and ground connections have different electrical roles. Typical uses include automotive body and chassis networks, industrial automation equipment, diagnostic systems, electric-vehicle subsystems, robotics, and embedded control platforms. It is particularly suitable when the CAN controller operates from 3.3 V while the surrounding vehicle or industrial network uses a conventional 5 V CAN physical layer. In these systems, the transceiver provides the physical interface while the CAN controller handles arbitration, framing, error management, and higher-level protocols. PCB implementation should follow the manufacturer's pin and layout guidance, including a common reference plane and a controlled return path beneath the bus connections. Decoupling and protection requirements should be evaluated against the actual vehicle or industrial network because external bus transients and ground offsets can exceed nominal logic-level conditions. The VIO connection must be referenced to the microcontroller supply, and unused or unused-after-configuration pins must not be left without consideration. This product record consolidates the verified NXP documentation, distributor availability, package information, lifecycle status, and same-family replacement information. It also highlights the practical distinction between the VIO-enabled /3 variant and other TJA1057 options so engineers can make a pin-compatible selection without confusing protocol support, interface voltage, or temperature-grade suffixes.

RFC Hubungi kami
TJA1057GTJ - High-Speed CAN Transceiver, 1Mbps, 8-SO | NXP
TJA1057GTJ

TJA1057GTJ - High-Speed CAN Transceiver, 1Mbps, 8-SO | NXP

The NXP Semiconductors TJA1057GTJ is a high-speed Controller Area Network (CAN) transceiver in the Mantis family, providing an interface between a CAN protocol controller and the physical two-wire CAN bus, delivered in an 8-pin SO (SOIC-8) surface-mount package. It supports data rates up to 1 Mbit/s, operates from a 4.75 V to 5.25 V supply, and is qualified for the -40 °C to +150 °C automotive temperature range. The TJA1057GTJ integrates differential transmit/receive capability, standby mode, and superior EMC and ESD performance versus earlier-generation transceivers. A CAN transceiver is the physical-layer (PHY) bridge between a digital CAN protocol controller (typically integrated into a microcontroller) and the differential CAN bus wiring in a vehicle or industrial network. Transceivers convert the controller's TX/RX logic-level signals into the ISO 11898-2 compliant differential bus levels, and they protect the controller from bus-level transients. The TJA1057GTJ belongs to NXP's Mantis family, which improved on the predecessor TJA1051/TJA1042 series by offering lower electromagnetic emissions and higher ESD robustness while maintaining pin compatibility. Key specifications include: 1 Mbit/s maximum data rate, 4.75 V to 5.25 V supply range, low-current standby mode, ISO 11898-2 conformance, bus pin ESD robustness of ±8 kV HBM (typical), and integrated thermal protection. The device is optimized for 12 V automotive systems and supports both normal and standby operation modes. The SOIC-8 package offers a standard 3.9 mm body width suitable for reflow soldering in automotive PCB assemblies. Architecturally, the TJA1057 uses a silicon-on-insulator process node that allows the bus pins (CANH, CANL) to survive load-dump transients up to ±42 V typical without external protection, while maintaining low quiescent current in standby mode. The device includes slope control for reduced EMI, dominant-timeout protection, and a bus-dominant detection feature that prevents the controller from being locked in a dominant state if a wiring fault occurs. Typical applications include automotive body and powertrain CAN nodes, industrial CANopen networks, gateway ECUs, and any 5 V microcontroller-based system requiring an ISO 11898-2 compliant physical layer. It is widely used in BMS modules, HVAC controllers, instrument clusters, and ADAS sensor nodes where reliable high-speed differential communication is required. When designing with the TJA1057GTJ, place a 100 nF decoupling capacitor close to pin 8 (VCC) and respect the bus termination scheme (typically 120 Ω at each end of the CAN bus segment). The standby pin (STB) should be tied to GND through a pull-down or controlled by the host MCU; a high level puts the part into low-power standby with the bus monitor still functional. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, including cross-references to TJA1057 family members and other 8-pin high-speed CAN transceivers.

RFC Hubungi kami
TJA1057GTK - High-Speed CAN Transceiver, 1 Mbit/s, 8-HVSON | NXP
TJA1057GTK

TJA1057GTK - High-Speed CAN Transceiver, 1 Mbit/s, 8-HVSON | NXP

The NXP TJA1057GTK is a high-speed Controller Area Network (CAN) transceiver from the Mantis family, providing an interface between a CAN protocol controller and the physical two-wire CAN bus in a compact 8-pin HVSON (3x3 mm) package with an exposed thermal pad. It supports data rates up to 1 Mbit/s, operates from a 4.75V to 5.25V supply, and delivers differential transmit/receive capability required by automotive in-vehicle networks. The TJA1057GTK variant includes a standby mode for low-power operation and is optimized for superior electromagnetic compatibility (EMC) and electrostatic discharge (ESD) performance. A CAN transceiver is a physical-layer interface IC that converts the digital transmit (TXD) and receive (RXD) signals from a CAN controller into the differential CANH and CANL bus voltages defined by the ISO 11898-2 standard. Within the broader hierarchy, a CAN transceiver sits below the CAN controller (typically inside a microcontroller) in the Open Systems Interconnection (OSI) model and sits above the physical bus medium. Without a transceiver, a controller cannot meet the bus-level timing, drive strength, or fault protection that an automotive CAN bus demands. Key features include a low-current standby mode with remote wake-up via bus activity, thermal protection, bus-dominant time-out to prevent a stuck node from blocking the bus, and an undervoltage detection on the VCC supply. The HVSON-8 package features an exposed thermal pad that reduces junction-to-ambient thermal resistance, enabling AEC-Q100-qualified automotive operation across the -40C to +125C range. The TJA1057 is pin-compatible with the legacy TJA1050 footprint in SO-8 but uses the smaller, thermally enhanced HVSON-8 package in this GTK suffix variant. The transceiver uses a symmetric differential driver stage that minimizes electromagnetic emissions, and the receiver incorporates a wide common-mode range to tolerate ground shifts between nodes on long bus runs. An integrated slope-control resistor optimizes the rise/fall times of the CANH/CANL edges to balance emissions against bit-timing symmetry. Typical applications include automotive body control modules, gateway ECUs, infotainment CAN interfaces, industrial CANopen networks, and any 12V/24V automotive subsystem that communicates via CAN at speeds from 10 kbit/s to 1 Mbit/s. Designers select the TJA1057GTK when EMC performance and a small PCB footprint outweigh the need for the higher bus-fault voltage ratings of the TJA1055 or TJA1044. When designing with this part, place a 100 nF decoupling capacitor as close as possible to the VCC pin, keep the CANH/CANL traces short and symmetric with characteristic impedance near 120 ohm, and verify that the termination resistance at each end of the bus totals 120 ohm to prevent signal reflections. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical EMC/layout notes drawn from the NXP TJA1057 datasheet family, offering context the manufacturer product page alone does not provide.

RFC Hubungi kami
TJA1057GTK/3Z - 5 Mbps High-Speed CAN Transceiver | NXP
TJA1057GTK/3Z

TJA1057GTK/3Z - 5 Mbps High-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1057GTK/3Z is a 5 Mbps high-speed CAN transceiver with a 5 V supply and normal or silent operating modes, packaged in an 8-terminal HVSON package measuring 3 mm by 3 mm by 0.85 mm. It belongs to NXP's Mantis family and provides the physical-layer interface between a Controller Area Network controller and a two-wire CAN bus. A CAN transceiver is an interface IC that converts logic-level transmit and receive signals into the differential voltage used on a CAN network. It belongs to the broader transceiver hierarchy, which includes unidirectional and bidirectional interface devices, and ultimately connects embedded control, automotive, and industrial communication systems. The two-wire CAN bus uses CANH and CANL conductors to carry complementary differential signals between nodes. The TJA1057GTK/3Z supports data rates up to 5 Mbps and includes normal and silent operating behavior. Its 5 V operating supply is suitable for conventional automotive and industrial electronic systems. The package uses a 0.65 mm terminal pitch in a compact 3 mm by 3 mm footprint, allowing CAN communication to be added where board area is constrained. The exposed thermal pad supports heat transfer from the transceiver into the PCB copper plane. The device belongs to the high-speed CAN transceiver category, designed to work with a CAN protocol controller rather than directly with a microcontroller's analog inputs. Differential signaling improves common-mode rejection and allows the bus to remain reliable when multiple nodes communicate over a shared two-conductor network. Normal mode supports ordinary CAN transmission and reception, while silent mode provides a way to monitor bus activity without actively driving the bus. Typical applications include automotive body and comfort modules, industrial automation controllers, CAN-based robotics, embedded instrumentation, and gateway equipment. The compact HVSON package is particularly useful in space-constrained controller boards where a conventional SOIC-style CAN transceiver would occupy more area. Its high-speed capability also supports communication links that exceed the rates commonly used by low-speed fault-tolerant CAN networks. When placing the device, follow the manufacturer pin-description and package-connection guidance, provide the required supply decoupling near VCC, and connect CANH and CANL to the protected bus network. The thermal pad should connect to the appropriate ground-plane structure specified by NXP. PCB signal integrity around the CAN pins should be maintained with short return paths and controlled stub lengths. This page organizes the package details, functional characteristics, sourcing information, and engineering considerations for the TJA1057GTK/3Z. It also identifies nearby same-family NXP options while clearly distinguishing verified drop-in suitability from options that require additional pinout, protocol, or qualification review.

RFC Hubungi kami
TJA1057GTKZ - High-Speed CAN Transceiver | NXP
TJA1057GTKZ

TJA1057GTKZ - High-Speed CAN Transceiver | NXP

The NXP TJA1057GTKZ is a high-speed CANbus interface transceiver with one transmitter and one receiver in an 8-pin HVSON surface-mount package measuring 3 x 3 mm. It operates from a 4.75 V to 5.25 V supply, supports an operating temperature range of -40 °C to +150 °C, and provides half-duplex operation with a 300 mV receiver hysteresis. The Z-qualified ordering code is supplied on tape-and-reel packaging with a standard quantity of 6000 units. A CAN transceiver is an interface IC that connects a CAN protocol controller, normally implemented in a microcontroller, to the physical two-wire CAN bus. Its transmitter converts controller logic into the differential CANH and CANL bus signals, while its receiver converts those differential signals back into logic levels for the controller. The TJA1057GTKZ belongs to the NXP Mantis family of high-speed CAN transceivers designed for automotive applications. Key verified features include one CAN driver, one CAN receiver, half-duplex communication, 300 mV receiver hysteresis, and a regulated 5 V supply range of 4.75 V to 5.25 V. The wide -40 °C to +150 °C operating range supports demanding industrial and automotive environments. Its 8-HVSON package provides a compact 3 x 3 mm surface-mount footprint for space-constrained electronic control units. The TJA1057GTKZ provides the physical-layer interface required by a Controller Area Network controller. Differential signaling improves common-mode noise tolerance on the bus, while receiver hysteresis helps distinguish a valid logic transition from noise near the decision threshold. Half-duplex operation means the transmitter and receiver share the same physical CAN interface in accordance with the CAN bus architecture. Typical applications include automotive CAN networks, electronic control units, body-control modules, powertrain controllers, industrial vehicle communications, and embedded systems that connect a microcontroller or another CAN controller to a two-wire bus. Its small package also suits compact control boards where connector area and routing space are limited. Designers should verify CANH, CANL, ground, supply, and logic-interface connections against the current NXP datasheet and the selected controller's I/O levels. The 5 V supply must remain within 4.75 V to 5.25 V. Exact data-rate, loopback, bus-fault, and absolute-maximum ratings were not included in the retrieved source data and must be confirmed in the manufacturer documentation. This product page consolidates verified manufacturer and distributor information, practical application guidance, pricing references, and strict drop-in alternative screening. It distinguishes documented TJA1057GTKZ characteristics from unverified generic substitutes so engineers can make a safer, footprint-conscious sourcing decision.

RFC Hubungi kami
TJA1057T - 1 Mbit/s High-Speed CAN Transceiver | NXP
TJA1057T

TJA1057T - 1 Mbit/s High-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1057T is a high-speed CAN physical-layer transceiver, specified for data rates up to 1 Mbit/s and supplied in an 8-pin SO package. It provides the differential transmitter and receiver interface between a CAN protocol controller and a two-wire CAN bus, supporting automotive and industrial Controller Area Network designs. A CAN transceiver is an interface IC within the broader network-interface and automotive electronics hierarchy. It converts the controller's logic-level TXD and RXD signals into a differential bus waveform and converts received bus levels back into a logic signal. This physical-layer function complements the CAN controller, which implements frame handling, arbitration, error detection, and protocol processing above the physical layer. The verified NXP material identifies the TJA1057 as a member of the Mantis family of high-speed CAN transceivers. The implementation is described as compatible with the CAN physical layer defined in ISO 11898-2:2016 and SAE J2284-1 through SAE J2284-5. The TJA1057T itself is specified for communication rates up to 1 Mbit/s, while the datasheet states that enhanced timing characteristics permit reliable use during the CAN FD fast phase at rates up to 5 Mbit/s for other supported variants. Automotive network design is the principal use case because the device couples a CAN protocol controller to the vehicle's two-wire bus. It is also relevant to industrial automation, robotics, building automation, and embedded equipment that uses classic CAN rather than a proprietary differential bus. The 8-pin SO package permits compact implementation in conventional through-hole automotive and industrial controller boards. The central engineering considerations are bus termination, common-mode behavior, transceiver supply requirements, loop delay, and controller timing. A CAN bus normally uses 120-ohm termination at both ends of the network. The transceiver itself does not replace the external bus resistors, and system designers must also account for parasitic cable and stub effects when choosing bit rates, routing, and protection networks. Because the supplied excerpts do not expose the complete ordering table, electrical limits, pin names, thermal ratings, or verified distributor prices, those details remain explicitly unresolved rather than being inferred. Engineers should use the official NXP datasheet for the final schematic, component values, timing budget, and production release decisions. The TJA1057T is marked NRND on the official NXP product page, so long-term procurement should be confirmed before committing new designs. This page consolidates the verified manufacturer lifecycle status, CAN standards coverage, data-rate distinction, packaging information, and practical application guidance. It also identifies data gaps and avoids presenting unverified electrical specifications or unsupported drop-in replacements as verified facts.

RFC Hubungi kami
TJA1057T/1Z - High-Speed CAN Transceiver | NXP SOIC-8
TJA1057T/1Z

TJA1057T/1Z - High-Speed CAN Transceiver | NXP SOIC-8

The NXP TJA1057T/1Z is a high-speed Controller Area Network (CAN) transceiver in the Mantis family, providing an interface between a CAN protocol controller and the physical two-wire CAN bus. Housed in an 8-pin SO (SOIC-8) package and specified for data rates up to 1 Mbit/s, it implements the CAN physical layer defined in ISO 11898-2:2024 third edition and SAE J2284-1 to SAE J2284-5, with additional timing parameters enabling reliable CAN FD fast-phase communication up to 5 Mbit/s. A CAN transceiver, also called a CAN physical-layer (PHY) chip, sits between a microcontroller's CAN protocol controller and the differential CANH/CANL bus wires. It transmits and receives differential signals, controls the slope of the dominant-to-recessive transitions, and provides ESD protection and bus-fault tolerance. The TJA1057 belongs to the Mantis CAN transceiver lineage that supersedes the older TJA1050; its position in the hierarchy is: CAN transceiver -> CAN interface IC -> automotive communication IC -> semiconductor. Key features include very low-current standby mode with remote wake-up via bus activity recognition, high ESD robustness on the bus pins (typical >8 kV HBM), excellent electromagnetic compatibility (EMC) performance under both dominant and recessive states, and an integrated VIO supply pin (on related variants) allowing direct connection to 3.3 V microcontrollers. It supports an extended supply voltage range, an operating junction temperature range suitable for automotive under-hood environments, and a low-power sleep current that simplifies ECUs designed for quiescent-current budgets. The device translates a single-ended TXD logic input from the CAN controller into a differential CANH/CANL output, and converts the bus differential back to a single-ended RXD logic output. It offers an SPLIT output pin (on related variants) for stabilizing the recessive bus level in networks with many nodes. The TJA1057 is a successor to the TJA1050 and is pin-compatible with several Mantis-family derivatives, simplifying PCB reuse across OEM programs. Typical applications include automotive body control modules, CAN gateways and powertrain nodes, electric vehicle battery management system communication, industrial CAN-bus automation (CANopen, DeviceNet), and any application needing an ISO 11898-2 compliant differential CAN link to a microcontroller. The 1 Mbit/s nominal / 5 Mbit/s CAN FD fast-phase capability suits both classical CAN and modern CAN FD networks. When designing with this IC, place the bus-side ESD/TVS protection and common-mode choke as close to the CANH/CANL pins as possible, and provide a solid ground pour under the SOIC-8 body. Decouple VCC with at least 100 nF and 4.7 µF local capacitance. Match the bus termination: 120 Ω between CANH and CANL at each end of the bus, plus optional split termination (60 Ω + 60 Ω to ground) for improved EMC. This page synthesizes distributor pricing, NXP Mantis-family drop-in alternatives, and practical design notes not found in the standalone TJA1057 datasheet.

RFC Hubungi kami