Produk (44,000+)

LFE2-6E-5F256I - 6K LUT, 190 I/O ECP2 FPGA | Lattice
LFE2-6E-5F256I

LFE2-6E-5F256I - 6K LUT, 190 I/O ECP2 FPGA | Lattice

The Lattice Semiconductor LFE2-6E-5F256I is an ECP2 field-programmable gate array with 6,000 logic cells, 190 user I/O, a -5 speed grade, and a 1.2 V core supply in a 256-ball Fine Pitch Ball Grid Array package. It is designed for compact, parallel digital logic, control, interface, and signal-processing designs requiring programmable nonvolatile configuration and deterministic FPGA performance. A field-programmable gate array is a programmable semiconductor containing configurable logic blocks and programmable interconnect. An FPGA sits above basic fixed-function logic in the hardware hierarchy: programmable logic blocks can be connected by engineers after manufacture, allowing parallel datapaths, state machines, interfaces, and embedded control functions to be consolidated into one device. ECP2 devices combine this reconfigurable architecture with an industrial-temperature option and a high-I/O package. The verified distributor data identifies the device as an ECP2 FPGA with 6K logic cells, 190 I/O, a -5 speed designation, and a 1.2 V operating rail. DigiKey additionally lists 56,320 configuration bits and identifies the physical device as a 256-BGA package. The supplied Microchip USA result describes the package as 17 mm by 17 mm and notes 190 user I/O pins. Its snippet inconsistently states 750 lookup tables, so that value is not used as an authoritative specification. Lattice describes the ECP2/M family as optimized for advanced DSP blocks and, for ECP2M devices, high-speed SERDES. The exact DSP-block count, system frequency ranges, memory quantities, I/O standards, configuration interfaces, and power characteristics are not present in the supplied source text and therefore require confirmation from the complete manufacturer datasheet before design release. The 190-I/O count is especially useful for dense board-level integration, but users must assign pins according to the official package data and bank constraints. Typical uses include industrial control, data acquisition, communications gateways, embedded instrumentation, and parallel processing. The 256-ball package supports fine-pitch assembly but demands careful PCB layout, ball assignment, power-plane distribution, and signal-integrity control. The -5 suffix denotes the supplier-classified speed grade, while the final I suffix is reported by Partstack as an industrial temperature grade. For PCB design, use the manufacturer pinout and package drawing rather than generic BGA assumptions. Validate every power, ground, configuration, clock, and user-I/O ball against the current Lattice documentation. Confirm supported I/O standards and voltage domains before connecting external devices. This page synthesizes the supplied distributor records, package details, and replacement cross-references into an engineering-oriented procurement and selection summary.

RFC Hubungi kami
LFE2-6E-5FN256C - 6K LUT ECP2 FPGA | Lattice Semiconductor
LFE2-6E-5FN256C

LFE2-6E-5FN256C - 6K LUT ECP2 FPGA | Lattice Semiconductor

Lattice Semiconductor LFE2-6E-5FN256C is an ECP2 field-programmable gate array with 6,000 logic cells, 190 user I/O, a 56,320-bit embedded memory resource, and a 1.2 V core supply in a 256-ball FBGA package. The -5 speed grade targets general-purpose programmable-logic designs where a compact 17 x 17 mm package and high I/O count are important. An FPGA is a reconfigurable digital semiconductor: lookup tables, flip-flops, routing resources, memory blocks, and programmable I/O form a digital system that can be configured after manufacture. Within the semiconductor hierarchy, an FPGA belongs to the programmable-logic device family and complements microcontrollers, DSPs, and application-specific standard products. It is especially useful when a design needs parallel logic, flexible interfaces, short development cycles, or field updates. The LFE2-6E-5FN256C provides 6,000 LUT-equivalent logic cells, 190 I/O, and up to 55 Kb of block RAM. Its 90 nm ECP2 implementation supports integration of control logic, data acquisition, communications, and general-purpose digital processing. The speed-grade designation is -5, and the device operates from a 1.2 V core, allowing a compact power-management design around the FPGA. The 256-ball FN256 package provides substantial connectivity for a device of this density. Its 17 x 17 mm area is suitable for module-level and embedded industrial equipment where a larger leaded package would be impractical. The ECP2 architecture also gives designers access to programmable logic blocks, embedded memory, PLL-based clocking resources, and dedicated I/O structures for common digital interfaces. Typical applications include industrial control and data acquisition, communications gateways, embedded video timing, test-and-measurement logic, network-interface front ends, and compact embedded systems. In each case, designers can implement parallel datapaths and peripheral control in one programmable device while retaining the option to revise the bitstream during product development. PCB design should prioritize clean power delivery to the 1.2 V core, low-impedance ground distribution, and short high-speed routing between FPGA banks and external memory or transceiver components. Use the manufacturer's pinout and package information to assign every ball, and verify the bank voltage requirements for each I/O group before connecting external circuitry. This product record combines the ECP2 device identity, resource counts, package details, pricing structure, compatible alternatives, and practical implementation guidance in one engineering-focused reference. It also highlights the distinctions among speed grades, package variants, and interface families so procurement and design teams can evaluate interchangeability without assuming that similar ECP2 devices are automatically interchangeable.

RFC Hubungi kami
LFE2-6E-5FN256I - 6K LUT FPGA, 190 I/O, 256-BGA | Lattice
LFE2-6E-5FN256I

LFE2-6E-5FN256I - 6K LUT FPGA, 190 I/O, 256-BGA | Lattice

The Lattice Semiconductor LFE2-6E-5FN256I is an ECP2 field-programmable gate array with 6,000 logic cells, 190 I/O, 1.2 V operation, and a 256-pin FBGA package. It is positioned for embedded systems that require reconfigurable logic, parallel interfaces, control functions, and moderate DSP processing in a compact surface-mount package. The -5 speed grade and industrial temperature designation identify this configuration for industrial operating conditions. An FPGA is a programmable semiconductor used to implement digital control, interface, timing, signal-processing, and data-path logic. Unlike a fixed-function application-specific integrated circuit, an FPGA can be reconfigured during development and can shorten the cycle between prototype and production. The ECP2 family belongs to Lattice Semiconductor's programmable-logic portfolio and is commonly used when design flexibility is more valuable than the very high logic density of a large FPGA. The LFE2-6E-5FN256I combines 6K LUTs, 190 I/O, 1.2 V supply operation, and embedded DSP capability in a 256-BGA package. The 190 I/O count supports connections to external memories, parallel buses, sensors, converters, and industrial peripherals. Its 1.2 V operating supply is suitable for systems designed around modern low-voltage digital logic. The -5 suffix identifies the speed grade, while the I suffix identifies the industrial temperature option. The FPGA architecture allows designers to implement parallel control logic, interface translation, data acquisition, and fixed-point signal-processing functions in one programmable device. This can reduce the number of supporting discrete logic components and allow firmware or configuration updates during product development. Designers must still account for I/O assignment, pin constraints, configuration memory, clocking, power integrity, and thermal performance in the PCB design. Typical uses include industrial automation, test and measurement, communications interfaces, embedded control, data acquisition, and compact embedded processing systems. The 256-BGA package is appropriate for multilayer PCB designs with adequate escape-routing capability and careful power delivery. It is not intended for a simple two-wire serial interface or a low-pin-count control-only design. When planning the layout, follow the manufacturer pinout and package guidelines, provide clean 1.2 V power rails, keep configuration and clock signals away from noisy analog or high-current switching paths, and validate all I/O standards against the target board voltage. This page summarizes the available LFE2-6E-5FN256I information, practical application fit, and same-package alternatives for engineering evaluation. The LFE2-6E-5FN256I is best selected when a 6K-logic ECP2 design needs 190 I/O, a 256-BGA footprint, and industrial-grade programmable logic. Compare speed-grade and package variants carefully, because a related MPN with a similar family name may not have identical electrical ratings, temperature coverage, or pin compatibility.

RFC Hubungi kami
LFE2-6E-5T144C - 6K LUT FPGA, 90 I/O | Lattice Semiconductor
LFE2-6E-5T144C

LFE2-6E-5T144C - 6K LUT FPGA, 90 I/O | Lattice Semiconductor

The Lattice Semiconductor LFE2-6E-5T144C is an ECP2 field-programmable gate array (FPGA) with 6,000 LUTs, 90 I/O, and a 144-LQFP package. The supplied distributor data identifies the device as a 1.2 V, -5 speed-grade ECP2 FPGA with a 20 x 20 mm lead-free package. It is positioned for programmable logic, control, interface, and embedded digital systems where a compact, high-pin-count FPGA is required. An FPGA is a programmable digital integrated circuit whose logic and interconnect resources can be configured after manufacture. In the broader hierarchy, an FPGA belongs to programmable logic devices and sits above basic logic gates but below application-specific processors and systems. The LatticeECP2 family provides configurable logic blocks, programmable routing, dedicated resources, and I/O structures for parallel and serial digital designs. The LFE2-6E-5T144C combines 6,000 LUTs with 90 I/O in a 144-lead LQFP package. The -5 designation is associated with a -5 speed grade in the distributor listings, while the package code and gull-wing terminal description identify a 144-terminal surface-mount FPGA. The exact core voltage, operating-temperature range, embedded-memory configuration, block-resource quantities, and pin functions were not included in the supplied verified data and are therefore not inferred here. Typical design uses include industrial control logic, data-acquisition front ends, communications-interface bridges, instrumentation, embedded test equipment, and general-purpose digital prototyping. The 90-I/O count can be valuable when a design requires multiple parallel buses, control signals, or high-speed external interfaces. Designers should still confirm pin availability, voltage standards, and timing constraints against the official Lattice ECP2 documentation before schematic capture. A key design consideration is power planning. The distributor result identifies a 1.2 V FPGA, but the supplied data does not state core current, I/O current, power consumption, junction temperature, or thermal resistance. Those values must be taken from the manufacturer datasheet and the actual switching activity of the implemented design. Decoupling, ground-plane continuity, and pin-compatible replacement verification remain essential during PCB implementation. This page consolidates the verified distributor identity, package information, device resource summary, availability links, and engineering-oriented application context. It distinguishes documented facts from parameters that require confirmation from the Lattice Semiconductor datasheet rather than estimating values.

RFC Hubungi kami
LFE2-6E-5T144I - 6K LUT, 90 I/O FPGA | Lattice
LFE2-6E-5T144I

LFE2-6E-5T144I - 6K LUT, 90 I/O FPGA | Lattice

The Lattice Semiconductor LFE2-6E-5T144I is a 6K-LUT ECP2 field-programmable gate array with 90 user-programmable I/O pins, 56,320 RAM bits, and a 1.2 V supply class, packaged in a 144-pin TQFP. The I suffix identifies the industrial-temperature offering, while the -5 speed grade and 144-pin package support designs requiring deterministic programmable logic in industrial embedded systems. A field-programmable gate array, or FPGA, is a programmable semiconductor used to implement control logic, interfaces, protocol handling, datapaths, and DSP functions after board fabrication. Within the broader semiconductor hierarchy, an FPGA combines configurable logic blocks, programmable interconnect, block RAM, and I/O resources. This makes it useful when a design requires rapid revisions, parallel channels, mixed logic functions, or a compact controller that would otherwise require several fixed-function devices. The verified product data identifies 6K LUTs, 90 I/O, 56,320 RAM bits, and a 1.2 V operating class. A 144-TQFP package provides 144 physical leads and a surface-mount form factor suitable for automated PCB assembly. The available listing data also reports 90 I/O and a 144-TQFP package, while detailed pin assignments, block counts, pin standards, and configuration interface details require the manufacturer datasheet before layout or replacement approval. Typical ECP2 applications include industrial control, instrumentation, embedded communication, motion-control logic, and general-purpose programmable signal conditioning. The programmable architecture lets designers consolidate parallel control functions into one FPGA, while the 90 I/O count supports external memory, converters, communications transceivers, status indicators, and actuator or sensor interfaces. Designers should verify voltage tolerances and pin multiplexing against the device-specific pinout rather than relying only on the package name. For robust implementation, begin with the manufacturer pinout and power specifications, then define bank voltage constraints before assigning external interfaces. Place decoupling capacitors close to every supply pin, preserve the package footprint and exposed thermal requirements specified by the manufacturer, and program the device using the supported Lattice toolchain. A hardware replacement is valid only after checking pinout, I/O standards, supply rails, timing, configuration interface, and temperature grade. This product page consolidates verified distributor and cross-reference information, practical selection guidance, and design cautions for engineers evaluating the LFE2-6E-5T144I. Exact price, lead time, stock status, pin-level electrical limits, and full timing/resource parameters are not supplied consistently in the provided source data and should therefore be confirmed before procurement or PCB release.

RFC Hubungi kami
LFE2-6E-5TN144C - 6K LUT FPGA, 90 I/O, 144-LQFP | Lattice
LFE2-6E-5TN144C

LFE2-6E-5TN144C - 6K LUT FPGA, 90 I/O, 144-LQFP | Lattice

Lattice Semiconductor LFE2-6E-5TN144C is an ECP2 field-programmable gate array with 6,000 logic cells, 90 I/O, 56,320 RAM bits, and a 1.2 V core supply in a 144-pin LQFP package. It combines programmable logic resources, dedicated DSP capability, and embedded block RAM in a low-power device suited to compact control, interface, signal-processing, and embedded systems. The 144-pin package provides more I/O than smaller ECP2 options while retaining a surface-mount form factor. An FPGA is a user-programmable semiconductor in the broader semiconductor and digital-logic hierarchy. Unlike a fixed-function application-specific integrated circuit, an FPGA allows logic, interfaces, and processing functions to be configured after manufacture. ECP2 devices combine LUT-based logic, block RAM, programmable I/O, and DSP resources in a single silicon platform. This makes the LFE2-6E-5TN144C suitable for designs where algorithms, protocols, or control logic must be adapted without changing the physical PCB. The device offers 6,000 logic cells, 90 I/O, 56,320 RAM bits, and a 1.2 V core voltage. Its DSP resources allow selected multiply-accumulate operations to be implemented more efficiently than in a purely LUT-based design. The 90 available I/O support communication ports, control signals, status indicators, and external memory or sensor interfaces. The -5 speed designation identifies the device’s manufacturer speed grade, while the TN144C suffix identifies its commercial-temperature and 144-pin package configuration. The LFE2-6E-5TN144C belongs to the ECP2 family, a compact FPGA architecture intended for low-cost embedded applications with modest logic requirements. Designers can implement state machines, bus interfaces, protocol conversion, digital filtering, and control logic in one device. Embedded RAM can retain data buffers and state, while DSP blocks can accelerate suitable arithmetic pipelines. The 1.2 V core keeps the device aligned with modern low-voltage digital systems and allows the FPGA to share nearby supply rails when its I/O and configuration requirements permit. Typical applications include industrial control and data acquisition, communications-interface bridging, embedded sensor processing, compact audio or control subsystems, and general-purpose digital logic prototyping. Its 90 I/O are especially useful when an implementation must connect multiple sensors, actuators, communications ports, and status signals without adding another large programmable-logic package. A key design consideration is I/O planning. Because the device has 144 physical positions but only 90 user I/O, not every package position is a general-purpose user pin. Use the manufacturer pin-description table and device documentation when assigning banks, dedicated configuration pins, power pins, and ground pins. PCB design must also preserve the ECP2 configuration interface and provide a deterministic startup path for reliable field operation. This page consolidates the verified resource counts, package information, sourcing links, compatible ECP2 alternatives, comparison parameters, and application-focused design guidance. It is intended to help engineers evaluate the LFE2-6E-5TN144C quickly while directing detailed programming, pinout, electrical, and timing decisions to the manufacturer documentation.

RFC Hubungi kami
LFE2-6E-5TN144I - 6K LUT ECP2 FPGA | Lattice Semiconductor
LFE2-6E-5TN144I

LFE2-6E-5TN144I - 6K LUT ECP2 FPGA | Lattice Semiconductor

Lattice Semiconductor LFE2-6E-5TN144I is an ECP2 field-programmable gate array with 6,000 logic cells, approximately 6K LUTs, 90 I/O, a 1.2 V core, and a -5 speed designation. The device is offered in a 144-pin TQFP package for surface-mount PCB designs. It combines programmable logic, embedded DSP capability, and programmable I/O in a single reconfigurable semiconductor. An FPGA is a programmable digital-logic device in which lookup tables, registers, interconnect resources, and other blocks are configured after manufacture. ECP2 devices belong to Lattice Semiconductor's low-density FPGA family, placing them between fixed-function logic and larger programmable-logic devices. This makes the LFE2-6E-5TN144I useful for control logic, bus arbitration, interface bridging, signal conditioning, and embedded DSP when a microcontroller or discrete logic implementation would be less flexible. Principal features include 6,000 logic cells, 6K LUTs, 90 I/O, one DSP block as identified in the product listing, and a 1.2 V operating core. The -5 suffix denotes the speed grade, while the final I identifies the industrial temperature option in Lattice Semiconductor's ECP2 ordering nomenclature. The TQFP-144 package provides 144 external pins and is compatible with conventional board-assembly and inspection processes. The device supports parallel programmable-logic implementation and serial configuration workflows commonly used with ECP2 devices. Its approximately 6K LUT capacity is suitable for moderate control domains, not processor-heavy workloads or large video pipelines. Engineers should allocate flip-flops, interconnect, memory resources, DSP multipliers, and I/O standards concurrently because each placement can affect achievable timing and routing density. Typical applications include industrial control, communications-interface bridging, test and measurement, embedded audio or motor-control signal processing, and compact embedded systems requiring field-updatable logic. The combination of 90 I/O and an embedded DSP block is particularly useful when a design needs parallel acquisition, digital filtering, protocol conversion, or deterministic control in one device. PCB design should preserve the manufacturer's recommended power, decoupling, configuration, and clocking layout. Confirm the exact pin assignments, supported I/O standards, configuration interface, and timing constraints in the manufacturer datasheet before schematic capture. The -5 grade and industrial temperature suffix should also be checked against the system timing and environmental requirements. This page consolidates the exact LFE2-6E-5TN144I attributes, same-package ECP2 alternatives, application guidance, and PCB design notes into one engineering-focused reference for FPGA selection, sourcing, and hardware implementation.

RFC Hubungi kami
LFE2-6E-6F256C - 6K LUT 190 I/O FPGA | Lattice Semiconductor
LFE2-6E-6F256C

LFE2-6E-6F256C - 6K LUT 190 I/O FPGA | Lattice Semiconductor

The Lattice Semiconductor LFE2-6E-6F256C is a 6,000-cell ECP2 field-programmable gate array with 6,000 LUTs, 190 I/O, 55 Kb block RAM, and a 1.2 V supply in a 256-pin FBGA package. Its -6 speed grade and DSP support suit compact control, interface, signal-processing, and embedded-logic designs requiring a high pin count and deterministic programmable logic. An FPGA is a semiconductor device whose digital behavior is defined by loading a configuration bitstream after manufacture. The ECP2 family belongs to the broader programmable-logic hierarchy and combines LUT-based combinational logic, embedded block RAM, programmable I/O, and dedicated DSP resources. This combination allows designers to implement parallel data paths, protocol handling, state machines, and control functions on one device. The verified listing identifies the LFE2-6E-6F256C as a 6K-LUT device with 190 I/O and DSP support at 1.2 V. Independent indexing also identifies the device as a 256-pin FBGA using 90 nm technology. These figures make the part relevant to industrial control, communications, test equipment, consumer electronics, and embedded systems that need more routing resources and I/O than a small programmable logic device can provide. The LFE2-6E-6F256C belongs to the LatticeECP2 family. Its large I/O count can simplify board-level connections when the design uses multiple buses, parallel data interfaces, or multiple external peripherals. The 55 Kb block RAM figure applies explicitly to the verified LFE2-6E-6FN256C family member; the supplied search data does not state that figure for LFE2-6E-6F256C, so that value is not used as a target specification here. For a new board, engineers should verify power rails, configuration interface support, I/O standards, pin constraints, and the exact package drawing before layout. Because the available evidence confirms 256 FBGA and 190 I/O but does not provide a complete manufacturer pin table, detailed ball assignments and electrical limits should be taken from the official Lattice documentation rather than inferred from distributor summaries. This page consolidates distributor availability, family-level technical context, procurement questions, and design cautions. It distinguishes verified facts from unavailable details and avoids treating generic FPGA advice as device-specific performance data. Check current distributor inventory and quote terms directly before committing a production BOM.

RFC Hubungi kami
LFE2-6E-6F256I - 6K LUT FPGA, 190 I/O, 256-BGA | Lattice
LFE2-6E-6F256I

LFE2-6E-6F256I - 6K LUT FPGA, 190 I/O, 256-BGA | Lattice

The Lattice Semiconductor LFE2-6E-6F256I is an ECP2 field-programmable gate array with 6,000 logic elements, 56,320 total RAM bits, and 190 general-purpose user I/Os, housed in a 256-pin fine-pitch ball grid array package. It is designed for embedded programmable-logic applications requiring moderate logic density, parallel I/O, and configurable DSP resources. An FPGA is a programmable semiconductor whose logic, interconnect, and memory resources can be configured after fabrication. The LFE2-6E-6F256I belongs to the ECP2 family and provides a compact implementation platform for control logic, data acquisition, protocol bridging, and embedded signal-processing functions. Its 6K LUT class can consolidate multiple fixed-function blocks into one device while retaining field-updatable firmware. Key verified features include 6,000 logic elements, 750 equivalent logic blocks, 190 user I/Os, 56,320 RAM bits, and a 1.2 V supply designation. Distributor listings identify the device as an ECP2 FPGA with a -6 speed grade and industrial temperature designation. The package is identified as a 256-BGA package. The ECP2 architecture is useful when a design needs programmable routing and logic rather than a fixed application-specific integrated circuit. The 190 I/O count provides substantial parallel connectivity for buses, counters, control signals, and external memory interfaces, while the available logic and RAM resources support moderate state machines and buffering. Exact timing, voltage tolerances, configuration details, and pin functions should be confirmed in the manufacturer data sheet before layout or production release. Typical applications include industrial control and factory automation, communication-interface bridging, instrumentation and test equipment, embedded data acquisition, and compact control systems. The FPGA can consolidate interface logic and control functions, reducing component count when firmware flexibility is important. When designing a board, preserve the manufacturer's recommended power, decoupling, configuration, clocking, and ball-grid-array layout requirements. Validate signal integrity and thermal performance across the complete operating temperature range and programmed logic configuration. This page consolidates verified distributor and product data, application guidance, package information, and selection considerations for engineers evaluating the LFE2-6E-6F256I.

RFC Hubungi kami
LFE2-6E-6FN256I - 6K LUT FPGA, 190 I/O, 256-BGA | Lattice
LFE2-6E-6FN256I

LFE2-6E-6FN256I - 6K LUT FPGA, 190 I/O, 256-BGA | Lattice

The Lattice Semiconductor LFE2-6E-6FN256I is an ECP2 field-programmable gate array with 6,000 logic cells, 190 I/O, 56,320 RAM bits, and a 256-ball FBGA package. It operates from a 1.14 V to 1.26 V supply, supports an industrial temperature range of -40°C to +100°C, and is identified in the supplied data as a 1.2 V, -6 speed-grade device. An FPGA is a programmable semiconductor containing configurable logic blocks, programmable interconnect, and I/O resources. Within the product hierarchy, the LFE2-6E-6FN256I is an FPGA, a member of the Lattice ECP2 family, and an example of a programmable logic device used for parallel processing, control, interface bridging, and embedded signal-processing functions. Its 750 LABs organize the available logic into flexible blocks, while the 190 I/O provide connections between the programmable core and external circuitry. Key features include 6,000 logic cells, 56,320 embedded RAM bits, 190 user I/O, and a 1.14 V to 1.26 V core-supply range. The package is a 17 mm by 17 mm, lead-free FPBGA-256. The “6” speed designation and the “-6” ordering code identify the performance grade, while the trailing “I” identifies the industrial temperature option. The 256-ball package supports dense routing for designs requiring numerous external connections. The ECP2 architecture combines programmable logic with embedded block RAM for designs requiring both control logic and local data storage. A 357 MHz maximum frequency is reported in the supplied component listing, making timing closure an important consideration for clocked datapaths. Because this device belongs to a mature FPGA family, engineers can use its configuration ecosystem and established design flows rather than developing fixed application-specific logic. Typical uses include industrial control and automation, communication interfaces, test and measurement equipment, embedded video or display control, and peripheral expansion for microcontrollers or processors. The 190 I/O are useful for parallel buses, status and control signals, and multi-bit data interfaces, while the embedded RAM can support buffers, packet processing, or state-holding functions. PCB design requires careful BGA fanout, differential-pair routing, ground-plane continuity, and decoupling around the 1.2 V supply rails. Designers should obtain the manufacturer pinout and power-decoupling guidance before routing the 256-ball footprint. Configuration programming and signal-integrity verification should also be included in the design plan rather than treated as late board-layout steps. This page consolidates the verified device specifications, current distributor information, package details, and same-family drop-in alternatives. It also adds application guidance and engineering checks that are not presented as a single manufacturer-datasheet conclusion, helping teams compare speed grades, temperature options, and package-compatible alternatives before committing to a PCB design.

RFC Hubungi kami
LFE2-6E-6T144C - 6K LUT, 90 I/O FPGA | Lattice Semiconductor
LFE2-6E-6T144C

LFE2-6E-6T144C - 6K LUT, 90 I/O FPGA | Lattice Semiconductor

The Lattice Semiconductor LFE2-6E-6T144C is an ECP2 field-programmable gate array with 6K LUTs, 90 I/O, 6,320 logic cells, and a 144-pin TQFP package. Its 1.2 V core and -6 speed grade make it a compact programmable-logic device for embedded control, interface bridging, signal conditioning, and industrial automation. The verified distributor listing identifies the device as a LatticeECP2 FPGA manufactured using 90 nm technology and supplied in a tray package. A field-programmable gate array is a semiconductor whose configurable logic and interconnect resources implement digital functions after fabrication. An FPGA occupies the programmable-logic portion of the wider semiconductor hierarchy, above fixed-function logic ICs and below application-specific programmable systems. The ECP2 family combines programmable logic blocks, memory resources, digital signal processing capability, and general-purpose I/O in one reconfigurable device. This makes the LFE2-6E-6T144C useful when design rules change faster than a custom ASIC can be produced. Key features include 6K LUTs, 6,320 cells, 90 I/O, a 1.2 V supply, and a -6 speed designation. The 144-pin TQFP package provides 144 external terminals in a surface-mount gull-wing format. Verified web results describe the part as an ECP2 FPGA with DSP capability, but detailed block counts, I/O standards, memory parameters, and timing values were not supplied in the retrieved evidence. Those values should therefore be confirmed against the manufacturer datasheet before a design is released. The part’s architecture is appropriate for glue-logic implementations, protocol conversion, control-plane logic, parallel data acquisition, and compact embedded systems. Its 90 I/O count can reduce the need for external programmable peripherals when the board-level pin budget is constrained. The -6 designation identifies the manufacturer’s speed grade, while the commercial C suffix appears in the ordering code; the retrieved evidence does not provide the exact commercial-temperature limits. Typical uses include industrial controllers, sensor aggregation modules, test equipment, embedded communications bridges, and compact control systems. A 1.2 V FPGA core simplifies power partitioning when the surrounding board already includes a 1.2 V rail, but external interface voltage levels must be selected independently and checked against the actual I/O specifications. The 144-pin package is larger than common QFN options, so PCB area and routing resources must be included in the mechanical design. For a new board, place the FPGA close to its clocks, decoupling network, configuration interface, and high-speed I/O routes. Keep power and ground connections short, follow the manufacturer’s recommended land pattern, and validate signal integrity for any external interface. This page consolidates verified distributor specifications, procurement information, replacement analysis, and engineering guidance rather than repeating only the part-number description.

RFC Hubungi kami
LFE2-6E-6T144I - 6K LUT FPGA, 90 I/O, 1.2 V | Lattice
LFE2-6E-6T144I

LFE2-6E-6T144I - 6K LUT FPGA, 90 I/O, 1.2 V | Lattice

The Lattice Semiconductor LFE2-6E-6T144I is an ECP2 series field-programmable gate array with 6,000 logic cells, 90 I/O, and 56,320 RAM bits in a 144-LQFP surface-mount package. The verified product data identifies a 1.2 V device with a -6 speed designation and an industrial temperature option encoded by the part number. Its architecture combines programmable logic resources, block RAM, and dedicated DSP capability in a compact programmable-logic device suited to embedded control, signal processing, communications, and industrial equipment. An FPGA is a reconfigurable digital semiconductor that contains configurable logic blocks and programmable interconnect. Unlike a fixed-function microcontroller or application-specific integrated circuit, an FPGA can be programmed after manufacture to implement control logic, data paths, interfaces, and algorithms. The ECP2 family belongs to the broader FPGA and programmable-logic hierarchy, combining flexible parallel hardware with configuration-based design updates. The LFE2-6E-6T144I provides 6K logic elements, 90 I/O, and 56,320 RAM bits according to DigiKey and Mouser results. One supplier result also identifies 750 logic array blocks or configurable logic blocks, while the available data reports a 1.14 V to 1.26 V supply range and an operating junction temperature beginning at -40 °C. The -6 speed grade identifies the device speed option, but the supplied data does not establish the complete timing table, configuration interface details, or absolute maximum ratings. Typical uses include industrial control logic, sensor and acquisition systems, communications interface aggregation, low-power signal processing, and embedded instrumentation. The 90-I/O count provides substantial board-level connectivity for buses, status signals, control outputs, and external interfaces. The 56,320 RAM bits can support buffering, packet storage, counters, and small data tables, while the FPGA architecture allows parallel operations without relying on sequential processor execution. When designing around this device, verify the exact pinout, configuration memory interface, clock requirements, supported I/O standards, and bank voltage constraints in the LatticeECP2/M family data sheet. Do not infer pin compatibility solely from a matching package. The supplied search data supports the core resource and package claims, but not a complete manufacturer-qualified replacement list. This page combines verified distributor specifications, application guidance, and design cautions for engineers evaluating the LFE2-6E-6T144I. It distinguishes documented facts from unavailable parameters so procurement and hardware decisions can be made without inventing electrical or timing data.

RFC Hubungi kami
LFE2-6E-6TN144C - 6K LUT ECP2 FPGA, 144-LQFP | Lattice
LFE2-6E-6TN144C

LFE2-6E-6TN144C - 6K LUT ECP2 FPGA, 144-LQFP | Lattice

The Lattice Semiconductor LFE2-6E-6TN144C is a member of the LatticeECP2 (ECP2) family of Field Programmable Gate Arrays (FPGAs) fabricated on a 90 nm CMOS process, integrating 6,000 Look-Up Tables (LUTs), 56,320 flip-flops (or system gates), and 90 user I/O in a 144-pin TQFP/LQFP (TQ = Thin Quad Flat Pack) surface-mount package. The device features a -6 speed grade, operates from a 1.2 V core supply, and supports embedded DSP blocks for low-cost signal processing. The "E" suffix denotes the ECP2 family (low-cost, high-volume) while "C" denotes the commercial temperature grade. An FPGA (Field Programmable Gate Array) is a semiconductor device whose logic functionality is defined after manufacturing by the user via a configuration bitstream loaded into on-chip SRAM. FPGAs sit hierarchically under programmable logic -> logic devices -> digital integrated circuits -> semiconductors. Unlike ASICs, FPGAs offer rapid prototyping, in-field re-programmability, and parallel hardware execution, making them ideal glue logic, interface bridging, and pre-silicon validation platforms. Key features of the LFE2-6E-6TN144C include 6,000 LUTs, 56,320 flip-flops equivalent in system gates, 90 user I/O pins, embedded sysDSP blocks for multiply-accumulate operations, dedicated DDR memory interface support, and on-chip PLLs for clock management. The device supports multiple I/O standards including LVCMOS, LVTTL, PCI, LVDS, SSTL, and HSTL. The 144-pin TQFP package is 22 mm × 22 mm with 0.5 mm pitch. The ECP2 architecture combines high-performance FPGA fabric with low-cost positioning, providing 311 MHz internal operation and pre-engineered IP cores through Lattice's ispLeverage / Lattice Diamond design tool chain. Embedded DSP blocks (typically 18×18 multipliers) accelerate signal-processing functions at lower power than soft multipliers implemented in LUT fabric. Hardened memory interface controllers simplify DDR1/DDR2 PHY integration. Typical applications include industrial control and factory automation glue logic, telecom interface bridging (SPI, I2C, UART, parallel buses), video processing front-ends, low-volume prototyping replacement for aging CPLDs, motor control and encoder interfaces, and medical/portable instrumentation requiring low-power programmable logic. The 6K LUT density suits medium-complexity state machines, bus conversion, and DSP pre-processing. When designing with this part, ensure all I/O banks receive proper VCCIO rail voltages matching the chosen I/O standard (1.2 V–3.3 V) and that the JTAG chain is properly terminated for in-system programming. Always validate timing closure at the chosen fMAX using Lattice Diamond timing analysis, as the 311 MHz figure is best-case for internal register-to-register paths only. This page synthesizes distributor pricing, drop-in alternatives within the ECP2 family, and practical design notes not consolidated in the manufacturer datasheet, helping engineers select the right speed grade, temperature grade, and package variant for production.

RFC Hubungi kami
LFE2-6E-6TN144I - 6K LUT ECP2 FPGA | Lattice
LFE2-6E-6TN144I

LFE2-6E-6TN144I - 6K LUT ECP2 FPGA | Lattice

Lattice Semiconductor LFE2-6E-6TN144I is an ECP2 field-programmable gate array with 6,000 logic cells, a 90 I/O interface, a 1.2 V core supply, and a 144-pin LQFP package. The -6 speed designation identifies the performance grade, while the industrial-temperature suffix supports applications requiring extended environmental operation. Its 90 nm programmable-logic process combines configurable logic, block RAM, and DSP resources in a low-cost device family designed for embedded control, communications, industrial automation, and general-purpose digital logic. An FPGA is a programmable-logic semiconductor whose digital function is defined by loading a configuration bitstream into on-chip memory. Within the semiconductor hierarchy, the LFE2-6E-6TN144I belongs to the ECP2 family of field-programmable gate arrays, placing it below programmable logic devices and above fixed-function logic integrated circuits. This distinction allows one PCB design to support firmware-driven changes in timing, interfaces, control algorithms, or system behavior without replacing the physical device. The device provides 6,000 logic cells and 90 user I/O in a surface-mount 144-pin LQFP package measuring 20 mm by 20 mm. A 1.2 V core operating voltage supports low-power logic implementation, and the -6 speed grade targets designs requiring more timing margin than slower ECP2 grades. The 90 I/O count is particularly useful for parallel control, data acquisition, industrial interfaces, and board-level integration where a programmable device must directly connect to multiple external signals. The ECP2 architecture provides programmable logic together with dedicated block RAM and DSP resources, allowing designers to implement control logic, counters, state machines, data pipelines, signal conditioning, and fixed-point processing in one device. The manufacturer classifies the part in the ECP2 family and identifies 6,000 cells, a 144-LQFP package, 90 I/O, and a 90 nm process node. This combination provides a practical platform for moderately complex digital systems where a small microcontroller is insufficient or an application-specific ASIC would not justify the development cost. Typical uses include industrial automation controllers, sensor and measurement interfaces, communication equipment, embedded data acquisition, motor and machine-control logic, and general-purpose digital signal conditioning. Its 90 I/O can simplify board partitioning when multiple buses, discrete inputs, and outputs must be consolidated. The 20 mm by 20 mm LQFP also remains practical for conventional multilayer PCB assembly methods rather than requiring fine-pitch BGA assembly. Designers should confirm the exact pin assignments, supported I/O standards, configuration requirements, clocking resources, and recommended power and decoupling networks against the manufacturer ECP2 documentation before layout release. Pay particular attention to the -6 speed designation, 1.2 V core supply, industrial-temperature ordering code, and package pinout. Configuration storage, JTAG access, programming voltage, and unused-pin treatment must also be validated for the selected board architecture. This product page combines the exact ECP2 ordering information with practical selection guidance, alternative cross-references, parameter comparisons, and design-oriented implementation notes. These resources help engineers identify whether the LFE2-6E-6TN144I fits the required logic density, I/O count, package, speed grade, and environment before beginning a new programmable-logic design.

RFC Hubungi kami
LFE2-6E-7F256C - 6000-LUT FPGA, 190 I/O, 256-BGA | Lattice
LFE2-6E-7F256C

LFE2-6E-7F256C - 6000-LUT FPGA, 190 I/O, 256-BGA | Lattice

The Lattice Semiconductor LFE2-6E-7F256C is an ECP2 field-programmable gate array with 6000 logic cells, 190 I/O, a 420 MHz maximum operating frequency, and a 256-ball BGA package. It is designed for compact programmable-logic applications requiring substantial logic capacity, parallel interfaces, and embedded DSP resources. The -7 speed designation and 1.2 V supply place it in the performance-oriented portion of the LatticeECP2 family. An FPGA is a semiconductor whose digital logic and interconnects are configured after manufacture. In the broader hierarchy, an FPGA is a programmable logic device and therefore a type of semiconductor IC. ECP2 devices combine LUT-based logic, programmable routing, block RAM, DSP capability, and user I/O in one package. This combination allows designers to implement control logic, interface bridges, packet processing, signal conditioning, and embedded data pipelines without relying on a custom ASIC. Verified distributor data identifies this device as an ECP2 FPGA with 6000 cells, 190 I/O, and a 256-BGA package. The LFE2-6E-7F256C also appears in comparison data as a 420 MHz, 6000-cell PBGA256 device measuring 17 x 17 mm. Its 190 available I/O support substantial board-level connectivity, while the ECP2 architecture provides a practical balance between logic density, programmable functionality, and device integration. The suffix C denotes a commercial-temperature ordering code in the supplied comparison data, but the complete temperature range is not available in the provided sources. Typical applications include industrial automation, communications infrastructure, embedded control, video and image processing, data acquisition, and DSP-assisted signal processing. Its 190 I/O are useful when an interface must connect multiple buses, counters, memory devices, converters, or control peripherals. Its 6000-cell capacity is suitable for parallel datapaths and moderate protocol stacks, although design headroom should be checked against routing, timing, RAM, DSP, and pin-assignment requirements before committing to a production build. For reliable implementation, use the manufacturer pin table and package information rather than generic BGA assumptions. Decoupling, bank-supply requirements, configuration pins, clock topology, I/O standards, and unused-ball treatment must follow the LatticeECP2/M Family Data Sheet. A programmable device also depends on a valid bitstream, correct configuration clocking, and a suitable Lattice programming interface. This page consolidates the supplied distributor listings, package information, and cross-reference evidence. It separates verified values from unavailable electrical details and does not infer pricing, lifecycle, pinout, or compliance claims that were not established by the source data. Engineers should evaluate the LFE2-6E-7F256C when a 6000-cell FPGA, 190 I/O, 420 MHz-class performance, and 256-BGA integration align with the design. Confirm timing closure, memory and DSP availability, package ball assignments, and supply status in the official documentation before hardware release.

RFC Hubungi kami
LFE2-6E-7T144C - 6K LUT ECP2 FPGA | Lattice Semiconductor
LFE2-6E-7T144C

LFE2-6E-7T144C - 6K LUT ECP2 FPGA | Lattice Semiconductor

Lattice Semiconductor LFE2-6E-7T144C is an ECP2 field-programmable gate array with 6,000 logic cells, 56,320 embedded RAM bits, and 90 user I/O in a 144-pin LQFP package. The verified product data identifies a 1.2 V device with a -7 speed designation and DSP capability. It is designed for compact programmable-logic applications where moderate logic density, embedded memory, and a large pin count are useful without moving to a larger FPGA. What is an FPGA? A field-programmable gate array is a reconfigurable digital integrated circuit containing programmable logic, memory, and input/output resources. An FPGA belongs to the programmable-logic hierarchy and can be programmed after manufacture to implement control logic, interfaces, data acquisition, signal processing, or embedded systems. The LatticeECP2 family combines programmable logic blocks, DSP resources, and I/O in an integrated device. The LFE2-6E-7T144C is identified by the verified sources as an ECP2 FPGA with 6,000 logic elements, 90 user I/O, 56,320 bits of on-chip RAM, and a 144-LQFP package. The separate product references also describe 750 logic blocks and a 1.14 V to 1.26 V supply range. The -7 speed code is retained from the verified listing, while the commercial temperature grade and full timing details require confirmation from the manufacturer datasheet. Its 90 user I/O make the device suitable for systems that need multiple external interfaces, parallel buses, status signals, or mixed control and data paths. The 144-LQFP package provides a conventional surface-mount footprint and exposes substantially more pins than a small FPGA package. Designers should account for package routing, power distribution, signal integrity, and thermal performance in the final PCB design. Typical uses include industrial control, instrumentation, embedded data acquisition, communications interfaces, DSP-assisted signal processing, and compact embedded control platforms. The DSP feature cited in the verified listings can reduce external processing hardware when the design uses suitable fixed-point operations and parallel datapaths. Before finalizing a design, verify the pinout, bank voltages, supported I/O standards, configuration method, clock requirements, and power-sequencing constraints against the LatticeECP2/M Family Data Sheet. The available search data does not provide a manufacturer-controlled purchase price or complete pin-level assignment, so those details must not be inferred. This page combines verified distributor specifications, package information, application guidance, and strict replacement criteria for engineers evaluating the LFE2-6E-7T144C.

RFC Hubungi kami
LFE2-6E-7TN144C - 6K LUT ECP2 FPGA | Lattice Semiconductor
LFE2-6E-7TN144C

LFE2-6E-7TN144C - 6K LUT ECP2 FPGA | Lattice Semiconductor

Lattice Semiconductor LFE2-6E-7TN144C is an ECP2 field-programmable gate array with 6,000 logic cells, approximately 6K LUTs, 90 I/O, and DSP capability. The device is manufactured in 90 nm technology and is available in a 144-pin TQFP package measuring 20 x 20 mm. It operates from a 1.2 V supply and is assigned the -7 speed designation. The LFE2-6E-7TN144C combines programmable digital logic, dedicated DSP resources, and a substantial pin count in a surface-mount package. An FPGA is a semiconductor whose digital behavior is defined after fabrication by loading a configuration bitstream. Within the product hierarchy, the LFE2-6E-7TN144C is a field-programmable gate array, a parallel programmable-logic device, and an FPGA within Lattice Semiconductor's ECP2 family. Unlike a fixed-function logic IC, an FPGA can implement parallel processing, control, communication, signal-conditioning, and data-capture functions in one device, reducing external component count when several independent logic blocks are required. The device's 6,000-cell ECP2 architecture provides about 6K LUTs for combinational and sequential logic, while 90 I/O positions provide substantial board-level connectivity. DSP capability supports designs involving multiplication, accumulation, filtering, and fixed-point signal processing. The 1.2 V core supply and -7 speed designation place the part in an ECP2 configuration optimized for compact, cost-sensitive programmable-logic systems requiring a large number of package pins. A 144-pin TQFP provides more I/O than smaller ECP2 packages, making this device useful when external interfaces, parallel buses, memory connections, or multiple high-speed signals dominate the design. The 20 x 20 mm body remains larger than a compact QFN package, but its exposed lead geometry supports conventional PCB assembly, inspection, and rework. Design teams should use the manufacturer pin table and package drawing to assign every power, ground, configuration, clock, and user I/O connection. Typical applications include parallel data acquisition, industrial control and automation, embedded protocol bridging, sensor aggregation, digital signal processing, general-purpose control logic, and communication-interface consolidation. Its combination of programmable logic, DSP support, 90 I/O, and a 144-pin package is particularly useful when a design must implement several bus interfaces or acquisition channels around a common control engine. The principal design considerations are power sequencing, configuration management, clock integrity, I/O voltage compatibility, and PCB routing density. Confirm that every connected peripheral uses compatible voltage levels, place configuration and decoupling networks according to the manufacturer reference design, and use controlled clock routing for timing-sensitive interfaces. Although alternatives exist in the same ECP2 family, speed grade and temperature suffix differences can alter interchangeability. This product page consolidates the exact device identity, package information, technical comparisons, and practical replacement guidance into one engineering-focused reference. It also distinguishes true same-package ECP2 alternatives from parts that differ in speed grade, temperature grade, or package designation, helping PCB designers make informed decisions without assuming that every similarly named FPGA is interchangeable.

RFC Hubungi kami
LFE2-6SE-5F256C - 6K LUT ECP2 FPGA | Lattice Semiconductor
LFE2-6SE-5F256C

LFE2-6SE-5F256C - 6K LUT ECP2 FPGA | Lattice Semiconductor

The Lattice Semiconductor LFE2-6SE-5F256C is an ECP2 series field-programmable gate array with 6,000 logic cells, 190 user I/O, and 56,320 bits of embedded block RAM. It operates from a 1.14 V to 1.26 V core supply and is packaged in a 256-ball FPBGA measuring 17 mm by 17 mm. The device is intended for compact embedded systems requiring programmable logic, parallel digital interfaces, and dedicated RAM resources. An FPGA is a semiconductor whose internal digital circuits are configured after manufacture. The LFE2-6SE-5F256C belongs to the ECP2 low-power FPGA family and combines configurable logic, block RAM, programmable I/O, and embedded DSP functions. This makes it a practical platform for consolidating control logic, communication interfaces, and small signal-processing functions into one device instead of using several discrete components. The principal resource figures are 6,000 logic cells, 190 user I/O, and 56,320 bits of block RAM. Its 1.2 V operating class supports low-voltage digital systems, while the 256-FPBGA package provides a high pin count for parallel buses and multi-channel interfaces. The -5 ordering code identifies the device speed grade, and the C suffix identifies the commercial temperature grade. The exact maximum operating frequency and temperature limits must be confirmed against the manufacturer datasheet before a production design is released. Within the ECP2 architecture, configurable logic blocks implement Boolean, arithmetic, control, and state-machine functions. Embedded block RAM provides dedicated storage for packet buffers, sampled data, lookup tables, and display or communications data. Programmable I/O blocks support external interfaces, while DSP resources can accelerate multiply-accumulate operations used by filters, waveform generation, and digital signal processing. These functions allow one FPGA to replace combinations of programmable logic and fixed-function digital ICs. Typical uses include industrial equipment controllers, motor and sequencing logic, data-acquisition front ends, communication gateways, embedded control systems, and compact consumer products. The 190 I/O count is particularly useful when a design must connect multiple sensors, actuators, memory devices, and parallel buses. The 56,320-bit RAM inventory is also suitable for buffering short frames, retaining sampled values, or implementing fixed-size lookup tables without external memory. Power and layout planning remain central to a successful BGA implementation. Confirm every supply rail, decoupling requirement, configuration interface, and pin assignment in the manufacturer datasheet. Preserve the specified ball assignments and follow the recommended land pattern, fanout, and manufacturing guidelines. Configuration storage, clocking, and I/O standards should be selected early because they affect both the PCB and the programmable design. This product page combines the verified device identity with application guidance, package-aware comparisons, and practical FPGA design notes. It also distinguishes same-family ordering options from their documented resource and ordering differences, helping engineers assess migration paths without overlooking speed, temperature, or board-level compatibility.

RFC Hubungi kami
LFE2-6SE-5F256I - 6000-LUT ECP2 FPGA, 256-BGA | Lattice
LFE2-6SE-5F256I

LFE2-6SE-5F256I - 6000-LUT ECP2 FPGA, 256-BGA | Lattice

Lattice Semiconductor LFE2-6SE-5F256I is an ECP2 field-programmable gate array with 6000 logic elements, 190 general-purpose I/O pins, and 56,320 bits of embedded RAM in a 256-ball BGA package. The device operates at a 1.2 V core voltage, includes S-Series DSP capabilities, and is identified as a 90 nm FPGA rated at a maximum clock frequency of 311 MHz. An FPGA is a programmable semiconductor in which logic, interconnect, and I/O behavior are configured through a bitstream rather than fixed during fabrication. ECP2 devices occupy the FPGA hierarchy alongside field-programmable gate arrays, programmable logic, and digital logic devices. Their combination of LUT-based logic, embedded block RAM, programmable I/O, and high-speed serial resources supports parallel processing, control, signal conditioning, and interface bridging within a single package. The LFE2-6SE-5F256I provides 6000 logic elements organized into 750 LABs or CLBs. Its 56,320 RAM bits support buffers, lookup tables, packet storage, and embedded data processing, while 190 I/O pins provide substantial interface capacity. The S-Series DSP feature set allows the FPGA fabric to implement parallel arithmetic, filtering, and fixed-point processing functions without requiring a separate DSP device in many designs. The device uses a 1.2 V supply for its programmable logic core. Its 256-BGA package is approximately 17 mm by 17 mm and is intended for surface-mount assembly. Because a BGA package has solder balls beneath the device, PCB layout must account for via-in-pad or via-under-ball routing, thermal management, assembly process capability, and the manufacturer’s recommended land pattern and component placement rules. Typical uses include industrial control, communications infrastructure, test and measurement, embedded signal processing, video interface bridging, and compact data-acquisition systems. The combination of 190 I/O and 56,320 RAM bits is particularly useful for designs that connect multiple buses, capture parallel data, and perform local processing without adding a separate high-speed memory device. Design decisions should begin with the intended clock rate, I/O voltage standards, RAM usage, pin constraints, and thermal environment. Because the -5 and I suffixes encode device-specific ordering information, engineers should confirm speed, temperature, and qualification requirements against the manufacturer documentation before releasing a production BOM. This page organizes the core ECP2 resources, package characteristics, drop-in candidates, design guidance, and application-specific engineering considerations into a practical selection reference for FPGA hardware development.

RFC Hubungi kami
LFE2-6SE-5T144C - 6K LUT ECP2 FPGA | Lattice Semiconductor
LFE2-6SE-5T144C

LFE2-6SE-5T144C - 6K LUT ECP2 FPGA | Lattice Semiconductor

Lattice Semiconductor LFE2-6SE-5T144C is an ECP2 field-programmable gate array with 6,000 logic cells, 6K LUTs, and 90 user I/O in a 144-LQFP package. It operates from a 1.2 V core supply and is identified with a -5 speed grade in the product listing. The device also includes S-Series DSP capability, making it suitable for compact control, interface, signal-processing, and embedded programmable-logic designs that require deterministic parallel I/O in a moderate pin-count package. An FPGA is a reconfigurable semiconductor whose logic, routing, and digital signal-processing resources can be programmed after manufacture. In the product hierarchy, the LFE2-6SE-5T144C is a programmable logic device, an FPGA, and specifically a member of the Lattice ECP2 family. Unlike a fixed-function application-specific integrated circuit, an FPGA allows parallel interface logic, control sequences, and DSP operations to be consolidated into one device while retaining field-updatable configurations. The ECP2 architecture provides 6K LUTs, 90 I/O, and S-Series DSP resources in the 144-LQFP configuration. The 1.2 V operating voltage identifies the device as a modern FPGA intended for integration with contemporary digital logic, while the -5 designation denotes the listed speed grade. The 144-pin LQFP package provides substantially more I/O than a small FPGA package and is practical for parallel buses, memory interfaces, control logic, and external data acquisition functions. Technical selection must account for both architecture and board constraints. ECP2 devices share a programmable platform, but ordering suffixes can distinguish speed grade, temperature grade, and package-related ordering options. Because FPGA configuration determines the implemented logic, designers should verify the exact device pinout, configuration interface, supported I/O standards, clocking resources, and power requirements in the LatticeECP2/M Family Data Sheet before committing the PCB footprint. Typical uses include industrial control modules, sensor and measurement interfaces, communication protocol bridges, audio or control DSP, and general-purpose embedded logic. The 90-I/O count is especially useful when several buses or discrete digital interfaces must be consolidated. The S-Series DSP resources can accelerate multiply-accumulate-oriented operations, although final throughput depends on the selected clock, routing, and logic architecture. PCB implementation requires careful attention to the 144-LQFP footprint, 1.2 V supply quality, decoupling, configuration access, and I/O assignment. Place bypass capacitors close to the supply pins, preserve a continuous return path, and follow the manufacturer's pin and layout guidance for the selected ECP2 package. Designers should also account for unused pins and configuration behavior in their board-level validation. This page organizes the published Lattice ECP2 specifications, same-package ordering alternatives, application guidance, and practical implementation notes. It supports design triage for the LFE2-6SE-5T144C by connecting resource counts, package capacity, speed-grade differences, and replacement constraints while directing final electrical and pin-level decisions to the manufacturer documentation.

RFC Hubungi kami
LFE2-6SE-5T144I - 6K LUT FPGA, 90 I/O, TQFP-144 | Lattice
LFE2-6SE-5T144I

LFE2-6SE-5T144I - 6K LUT FPGA, 90 I/O, TQFP-144 | Lattice

Lattice Semiconductor LFE2-6SE-5T144I is an ECP2-series field-programmable gate array with 6,000 logic cells, 6K LUTs, 90 I/O, and a 144-pin TQFP package. It operates from a 1.2 V core supply and is specified as an industrial-temperature, -5 speed-grade device. The combination of programmable logic, DSP capability, and 90 user I/O makes it suitable for embedded control, signal processing, communications, and industrial interface consolidation. An FPGA is a semiconductor device whose digital logic is configured after manufacture. By combining programmable lookup-table logic, programmable interconnect, memory resources, and dedicated input/output blocks, an FPGA allows one physical device to implement functions that might otherwise require several discrete logic devices. Within the broader semiconductor hierarchy, an FPGA belongs to the programmable-logic family, alongside CPLDs, and provides higher implementation flexibility than fixed-function logic. The LFE2-6SE-5T144I provides 6,000 FPGA logic cells and 6K LUTs, giving a design engine approximately 12,000 registers when both halves of each logic cell are used. Its 90 I/O pins support connections to external memories, processors, sensors, communications transceivers, and industrial peripherals. The 1.2 V core supply identifies it as a modern low-voltage FPGA architecture, while the -5 grade denotes its speed position within the ECP2 ordering system. The part is intended for industrial environments rather than the extended automotive grade. The ECP2 implementation includes DSP-oriented resources suited to arithmetic and filtering functions, as well as serial-interface capabilities referenced in the product description. These resources allow designers to consolidate signal-processing and control logic into a single programmable device. The 144-pin TQFP package also exposes substantially more device connectivity than smaller FPGA packages, making the device appropriate for designs that need multiple parallel buses, memory interfaces, or external control signals. Typical uses include industrial automation controllers, data-acquisition systems, communications equipment, embedded processing adjuncts, and general-purpose embedded control. In a data-acquisition system, its parallel I/O can connect to converters or sensors while programmable logic performs filtering, protocol handling, and control. In industrial equipment, the -5 speed grade and industrial temperature designation align with long-running control systems where device availability and deterministic logic performance are important. Designers should match the selected ECP2 pinout, bank voltage requirements, configuration method, memory interface, and differential I/O constraints against the exact 144-pin device documentation. Power planning should include separate treatment of the 1.2 V core and applicable I/O supply rails. Configuration signals, clocking, decoupling, and serial programming connections must also be verified against the manufacturer pin-description and configuration guidance before schematic release. This product page combines the core ECP2 device facts with package-aware replacement guidance, design considerations, and application-focused engineering context. It helps distinguish speed, temperature, and package suffix changes that otherwise look interchangeable but can affect qualification, timing, and production sourcing decisions.

RFC Hubungi kami
LFE2-6SE-6F256C - 6000-LUT ECP2 FPGA, 357MHz, 256-BGA
LFE2-6SE-6F256C

LFE2-6SE-6F256C - 6000-LUT ECP2 FPGA, 357MHz, 256-BGA

The Lattice Semiconductor LFE2-6SE-6F256C is an ECP2 field-programmable gate array with 6,000 logic cells, 190 user I/O, 357 MHz performance, and a 1.2 V operating supply in a 256-pin FBGA package. It is designed for embedded logic, interface bridging, control, and signal-processing designs requiring a compact programmable implementation. An FPGA is a programmable-logic semiconductor whose lookup tables, registers, and interconnect resources are configured by a bitstream rather than permanently connected by masks. The ECP2 family belongs to the broader FPGA and programmable-logic hierarchy, combining logic fabric, configurable I/O, embedded memory resources, and dedicated signal-processing capabilities in one device. This makes the LFE2-6SE-6F256C suitable when design rules or interfaces are likely to evolve after prototyping. The device provides 6,000 logic cells, 56,320 flip-flops, 190 I/O, and S-Series DSP resources according to the manufacturer product listing. Its maximum reported performance is 357 MHz. The 1.2 V operating specification supports modern low-voltage logic implementations, while the 256-pin FBGA package provides high I/O density for designs with numerous parallel, differential, serial, or mixed-signal connections. The package measures 17 x 17 mm according to the indexed datasheet listing. The LFE2-6SE-6F256C is identified as a 90 nm ECP2 FPGA. Its programmable architecture allows designers to implement control logic, bus arbitration, protocol conversion, data acquisition, and DSP functions in parallel. The S-Series designation corresponds to the ECP2 family feature set listed for the part, including S-Ser DSP capability. Configuration, programming, timing, and I/O details should be checked against the manufacturer ECP2 documentation for the exact device revision. Typical applications include industrial control systems, communications interfaces, instrumentation, embedded test equipment, video and image processing, sensor fusion, and general-purpose embedded logic. The 190 I/O count is particularly useful for parallel control or data-acquisition designs, while DSP resources can accelerate filtering, arithmetic, and signal-conditioning operations without relying on a separate processor for every function. PCB implementation requires careful treatment of the 256-ball BGA land pattern, power and ground distribution, decoupling, and high-speed routing. Follow the package ball map, recommended power architecture, and decoupling guidance in the Lattice ECP2 documentation. Validate signal integrity and timing after PCB fabrication rather than relying only on schematic-level assumptions. This product page consolidates the exact device identity, package and capacity information with application guidance, comparison considerations, and practical design notes. It helps engineers distinguish the ECP2 options by logic capacity, speed, temperature suffix, and package while emphasizing that a valid hardware replacement still requires pinout, timing, configuration, and lifecycle verification.

RFC Hubungi kami
LFE2-6SE-6F256I - 6K LUT ECP2 FPGA, 256-BGA | Lattice
LFE2-6SE-6F256I

LFE2-6SE-6F256I - 6K LUT ECP2 FPGA, 256-BGA | Lattice

Lattice Semiconductor LFE2-6SE-6F256I is an ECP2 field-programmable gate array with 6,000 logic elements, 6K available LUTs, 190 user I/O pins, and 56,320 RAM bits in a 256-BGA package. The device operates from a 1.2 V core supply and is identified as a -6 speed-grade industrial option. An FPGA is a reconfigurable digital semiconductor used to implement logic, state machines, interfaces, and parallel processing functions after hardware manufacture. The ECP2 family occupies the FPGA hierarchy below application-specific programmable logic and combines programmable logic blocks, embedded block RAM, programmable I/O, and dedicated serial capabilities in one highly integrated device. This makes the LFE2-6SE-6F256I suitable for embedded control, communications, industrial automation, and signal-processing systems. The principal resources include 6,000 logic elements, 56,320 RAM bits, and 190 user I/O, while the device is identified as a 6K LUT ECP2 FPGA with S-Ser DSP support. Its -6 ordering code denotes the speed grade shown in the product listing. The 256-BGA package provides a dense board footprint for designs requiring extensive connectivity, although ball assignments, differential I/O support, and exposed-pad requirements must be confirmed against the manufacturer pinout and package documentation before layout release. The ECP2 architecture supports parallel programmable logic, embedded memory, and high-speed serial communication resources in a single device. Designers can use the 190 available user I/O for control signals, external memory interfaces, sensor acquisition, or industrial bus connectivity where the relevant bank voltage and interface limits permit. Logic utilization depends on the selected clocking, memory, I/O standards, and routing architecture, so a design should be fitted with the Lattice implementation tools rather than estimated solely from LUT count. Typical applications include industrial control systems, network interface modules, video and image-processing pipelines, test equipment, industrial networking, and embedded serial bridges. The device is particularly relevant when moderate logic density and a large I/O count are more important than very high FPGA capacity. It also suits designs requiring an S-Ser DSP path for serialization, clocking, or data movement. PCB implementation should preserve the manufacturer's ball map, power architecture, decoupling requirements, and high-speed routing rules. Validate every supply rail, I/O voltage, configuration connection, and thermal condition against the exact -6F256I ordering code. When planning a migration, distinguish speed-grade, temperature-grade, package, and density changes because a shared package name alone does not establish pin-to-pin interchangeability. This product page combines the verified ECP2 resource and package data with same-package alternatives, comparison parameters, and design guidance. It supports early architecture selection while leaving final pin assignment, timing closure, power budgeting, and board-layout approval to the manufacturer documentation and Lattice design flow.

RFC Hubungi kami
LFE2-6SE-6T144C - 6K LUT ECP2 FPGA | Lattice Semiconductor
LFE2-6SE-6T144C

LFE2-6SE-6T144C - 6K LUT ECP2 FPGA | Lattice Semiconductor

Lattice Semiconductor LFE2-6SE-6T144C is an ECP2 field-programmable gate array with 6,000 logic cells, 90 user I/O, and a -6 speed grade in a 144-pin TQFP/LQFP package. The device uses 90 nm FPGA technology, operates with a 1.2 V core supply, and includes programmable serial SerDes resources suitable for high-speed communications and DSP-oriented signal processing. An FPGA is a user-programmable semiconductor in which interconnect and logic are configured after manufacture. The ECP2 family belongs to the broader FPGA and programmable-logic hierarchy, combining configurable logic blocks, embedded block RAM, programmable I/O, and dedicated high-speed serial channels. This makes the device useful where designers need parallel processing, flexible interfaces, protocol adaptation, or deterministic hardware logic in a compact surface-mount package. The LFE2-6SE-6T144C provides 6,000 FPGA cells, 56,320 flip-flops, and 90 user I/O according to its manufacturer product listing. Its -6 performance designation identifies the device speed option, while the 144-pin package exposes substantially more I/O than smaller FPGA packages. Integrated serial capability supports applications requiring multiple high-speed links rather than only parallel logic and general-purpose I/O. The ECP2 architecture is implemented in 90 nm process technology and uses a 1.2 V core voltage. This combination places the device in the low-voltage programmable-logic class, where system-level power depends on core voltage, I/O standards, switching activity, configuration method, and utilization. The 144-pin TQFP/LQFP package also provides a large perimeter for routing general-purpose I/O and reduces the need for fine-pitch fan-out in prototype and medium-density designs. Typical uses include serial-interface bridges, industrial control and instrumentation, test and measurement equipment, embedded DSP pipelines, data acquisition front ends, and communications equipment requiring multiple SerDes channels. The device can consolidate protocol conversion, clock-domain interfacing, packet framing, and parallel control logic into one programmable component while preserving the flexibility of FPGA-based updates. PCB design should preserve adequate decoupling at every supply pin, route configuration and serial interfaces according to the manufacturer pinout, and validate high-speed channel routing with controlled-impedance geometry. Designers should also account for the -6 speed grade in timing constraints and confirm the exact I/O voltage domains before assigning pins to external standards. This page combines the exact LFE2-6SE-6T144C specifications, family-level replacement guidance, package information, application engineering notes, and a parameter comparison to support faster design evaluation and sourcing decisions.

RFC Hubungi kami