Produk (44,000+)

MAX232EING4 - Dual RS-232 Transceiver | Texas Instruments
MAX232EING4

MAX232EING4 - Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232EING4 is a dual RS-232 line-driver and receiver interface IC with a 5 V supply, a maximum signaling rate of 250 kbps, and differential RS-232 outputs rated to ±9 V. The device is packaged in a 16-pin PDIP and provides on-chip charge-pump voltage conversion for a single-supply implementation. An RS-232 transceiver is an interface IC that converts low-voltage TTL or CMOS logic signals into RS-232 bipolar levels and converts incoming RS-232 signals back into logic-compatible levels. Within the interface hierarchy, the MAX232 belongs to the RS-232 transceiver class, connects digital logic to serial communication equipment, and forms part of a broader communications interface semiconductor. It is intended for point-to-point RS-232 links rather than multidrop networks. Key features include two driver and two receiver channels, 5 V operation, ±9 V RS-232 output levels, and ±2 kV ESD protection on the RS-232 pins. The 250 kbps maximum data rate supports common asynchronous serial interfaces when the associated baud rate, cable length, capacitance, and receiver loading permit reliable operation. An industrial temperature option allows operation from -40 °C to +85 °C. The MAX232 architecture uses charge-pump circuits to generate the positive and negative voltages required by RS-232 transmitters. Each driver converts a logic-high or logic-low input into a corresponding bipolar output, while each receiver uses thresholding to determine the incoming signal state. The integrated voltage conversion avoids a separate negative power supply, although external charge-pump capacitors are required. Typical applications include industrial serial controllers, data-acquisition equipment, instrumentation interfaces, service equipment, and legacy computer serial ports. The IC can bridge a UART or other CMOS/TTL controller to an RS-232 connector when signal polarity, grounding, and cable requirements are handled correctly. It is especially useful where a 5 V logic system must communicate with older RS-232 equipment. Designers should place the charge-pump capacitors close to their associated pins and provide a stable, low-impedance bypass path at the supply pins. Long or capacitively loaded cables can reduce the usable baud rate, and the grounded shield or signal ground must be connected according to the RS-232 interface standard. Input and output logic levels should also be checked against the UART voltage thresholds. This page combines the manufacturer’s electrical characteristics, package information, application guidance, drop-in candidates, and practical circuit considerations to support faster component selection and implementation.

RFC Hubungi kami
MAX232EIPW - 250kbps RS-232 Transceiver | Texas Instruments
MAX232EIPW

MAX232EIPW - 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232EIPW is a dual RS-232 driver and receiver that provides two data channels at up to 250kbps from a single 5V supply. It uses an on-chip capacitive voltage generator to produce the bipolar TIA/EIA-232-F voltage levels required by RS-232, while the receivers convert remote serial signals to 5V TTL/CMOS logic. The device is available in a 16-pin TSSOP package. An RS-232 transceiver is an interface IC that bridges the voltage-domain difference between a digital controller and a physical RS-232 link. In the signal hierarchy, the MAX232EIPW belongs to the RS-232 transceiver class, which combines line drivers, line receivers, and charge-pump voltage generation within one interface package. Unlike a TTL/CMOS serial controller, this device does not implement a communication protocol; it converts logic levels and protects the physical interface. Key electrical features include 5V operation, dual transmit and receive channels, 250kbps maximum data rate, and approximately ±9V RS-232 output levels. According to the MAX232E product page, all RS-232 pins provide 15kV human-body-model and IEC61000-4-2 air-gap discharge protection. The line-driver pins additionally provide 8kV IEC61000-4-2 contact-discharge protection, making the interface suitable for industrial equipment, service ports, and external cables where electrostatic discharge is a practical concern. The integrated voltage generator eliminates the need for a separate negative supply rail. Four charge-pump capacitors allow the device to translate TTL/CMOS transmit inputs into RS-232 levels from one 5V supply. Each receiver converts a TIA/EIA-232-F input into a 5V TTL/CMOS signal, allowing a microcontroller, programmable logic controller, or test system to communicate over a legacy serial port without a separate level-shifting circuit. Typical uses include industrial control-panel service ports, configuration and debug interfaces, laboratory equipment, point-of-sale systems, and legacy peripherals that retain an RS-232 connection. The 250kbps capability supports moderate-rate command and data links, although the connected software protocol must also be configured for the selected baud rate. Because RS-232 is a point-to-point, single-ended interface, ground reference and cable routing remain important in multi-device installations. For PCB layout, place the charge-pump capacitors and the VCC bypass capacitor close to their associated pins, and route the RS-232 driver and receiver connections directly to the connector. Keep logic-side traces away from exposed cable-facing nets, provide a stable chassis or signal-ground connection strategy, and avoid long unprotected stubs. The integrated ESD protection reduces connector-side risk but does not eliminate the need for good mechanical grounding and cable management. This page consolidates the verified MAX232E electrical characteristics, ordering information, protection ratings, application guidance, and interface design considerations into a practical engineering reference. It also distinguishes the MAX232EIPW from related MAX232 and MAX3232E family members so engineers can assess pin compatibility, supply voltage, data rate, and package differences before approving a substitution.

RFC Hubungi kami
MAX232EIPWG4 - Dual RS-232 Interface | Texas Instruments
MAX232EIPWG4

MAX232EIPWG4 - Dual RS-232 Interface | Texas Instruments

The Texas Instruments MAX232EIPWG4 is a dual RS-232 driver/receiver interface IC with two transmit channels, two receive channels, and IEC 61000-4-2 electrostatic-discharge protection. It operates from a single 5 V supply, supports data rates up to 120 kbit/s, and uses 1.0 uF charge-pump capacitors. The device is packaged in a 16-pin TSSOP package. According to the MAX232EIPWG4 datasheet, it meets or exceeds TIA/RS-232-F and ITU Recommendation V.28 while tolerating input levels up to plus or minus 30 V. An RS-232 transceiver is an interface IC that translates logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic levels. It belongs to the interface IC hierarchy, connects digital equipment to serial communication equipment, and handles the voltage conversion that the RS-232 standard requires. The MAX232EIPWG4 uses an internal charge-pump circuit to generate the positive and negative voltages needed by its two RS-232 drivers. Key features include two integrated drivers, two integrated receivers, operation from one 5 V power supply, 120 kbit/s operation, plus or minus 30 V receiver input capability, and IEC 61000-4-2 protection. The protected receiver inputs are particularly useful where cables connect to external equipment and electrostatic discharge may enter the system through the serial connector. Its integrated charge-pump design simplifies interface implementation compared with discrete level-shifting networks. Technically, the MAX232EIPWG4 combines RS-232 line drivers, RS-232 receivers, and regulated charge pumps in one package. The 1.0 uF charge-pump capacitors establish the internal voltage rails used by the drivers. Receiver inputs tolerate plus or minus 30 V levels, allowing the interface to remain connected to standard RS-232 ports when the local logic supply is 5 V. The device is intended for industrial-temperature operation, with a gull-wing TSSOP package suited to conventional surface-mount PCB assembly. Typical uses include industrial serial-control panels, test and measurement equipment, point-of-sale terminals, service-console links, and data-acquisition equipment. The dual-channel arrangement allows one device to support two RS-232 ports when both transmit and receive lines are required. Its 120 kbit/s capability is appropriate for legacy serial protocols, configuration interfaces, and equipment-control links rather than modern high-speed Ethernet or USB communication. PCB implementation should follow the manufacturer datasheet's charge-pump capacitor connection and keep the MAX232EIPWG4 close to the RS-232 connector. Confirm capacitor voltage rating, polarity, and placement against the datasheet requirements. Protect connector-side routing from unintended board contamination, and maintain suitable ground-return continuity between connected equipment. For a new design, verify that the remote equipment still uses RS-232 rather than RS-422, RS-485, or another differential interface. This page combines the device's stated electrical characteristics with application guidance, package-aware selection criteria, and verified drop-in alternatives. It also distinguishes true same-footprint replacements from parts that merely perform the same RS-232 function but require a different PCB footprint.

RFC Hubungi kami
MAX232EIPWR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX232EIPWR

MAX232EIPWR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX232EIPWR is a dual RS-232 driver and receiver that provides two data channels at up to 250kbps from a single 5V supply. It uses an on-chip capacitive voltage generator to produce the bipolar TIA/EIA-232-F voltage levels required by RS-232, while the receivers convert remote serial signals to 5V TTL/CMOS logic. The device is available in a 16-pin TSSOP package. An RS-232 transceiver is an interface IC that bridges the voltage-domain difference between a digital controller and a physical RS-232 link. In the signal hierarchy, the MAX232EIPWR belongs to the RS-232 transceiver class, which combines line drivers, line receivers, and charge-pump voltage generation within one interface package. Unlike a TTL/CMOS serial controller, this device does not implement a communication protocol; it converts logic levels and protects the physical interface. Key electrical features include 5V operation, dual transmit and receive channels, 250kbps maximum data rate, and approximately ±9V RS-232 output levels. According to the MAX232E product page, all RS-232 pins provide 15kV human-body-model and IEC61000-4-2 air-gap discharge protection. The line-driver pins additionally provide 8kV IEC61000-4-2 contact-discharge protection, making the interface suitable for industrial equipment, service ports, and external cables where electrostatic discharge is a practical concern. The integrated voltage generator eliminates the need for a separate negative supply rail. Four charge-pump capacitors allow the device to translate TTL/CMOS transmit inputs into RS-232 levels from one 5V supply. Each receiver converts a TIA/EIA-232-F input into a 5V TTL/CMOS signal, allowing a microcontroller, programmable logic controller, or test system to communicate over a legacy serial port without a separate level-shifting circuit. Typical uses include industrial control-panel service ports, configuration and debug interfaces, laboratory equipment, point-of-sale systems, and legacy peripherals that retain an RS-232 connection. The 250kbps capability supports moderate-rate command and data links, although the connected software protocol must also be configured for the selected baud rate. Because RS-232 is a point-to-point, single-ended interface, ground reference and cable routing remain important in multi-device installations. For PCB layout, place the charge-pump capacitors and the VCC bypass capacitor close to their associated pins, and route the RS-232 driver and receiver connections directly to the connector. Keep logic-side traces away from exposed cable-facing nets, provide a stable chassis or signal-ground connection strategy, and avoid long unprotected stubs. The integrated ESD protection reduces connector-side risk but does not eliminate the need for good mechanical grounding and cable management. This page consolidates the verified MAX232E electrical characteristics, ordering information, protection ratings, application guidance, and interface design considerations into a practical engineering reference. It also distinguishes the MAX232EIPWR from related MAX232 and MAX3232E family members so engineers can assess pin compatibility, supply voltage, data rate, and package differences before approving a substitution.

RFC Hubungi kami
MAX232EPE+ - +5V RS-232 Transceiver, 2/2, 16-PDIP | Maxim Integrated
MAX232EPE

MAX232EPE+ - +5V RS-232 Transceiver, 2/2, 16-PDIP | Maxim Integrated

The Maxim Integrated MAX232EPE+ is a +5V-powered, multichannel RS-232 line driver/receiver from the MAX220-MAX249 family, providing 2 drivers and 2 receivers (2/2) in a 16-pin PDIP through-hole package. It operates from a single 4.5V to 5.5V supply and generates the required RS-232 ±10V output levels internally using an integrated charge-pump with four external 1µF capacitors — eliminating the need for a ±12V power rail. Typical data rate is 120 kbps, and the device is qualified for the extended industrial -40°C to +85°C operating temperature range. What is an RS-232 transceiver? An RS-232 transceiver is a type of interface IC that translates logic-level signals (0/3.3V or 0/5V) to and from the ±5V to ±15V voltage levels defined by the EIA/TIA-232E (formerly RS-232) and ITU V.28/V.24 standards for serial communication. These parts sit in the hierarchy: RS-232 transceiver → line driver/receiver → interface IC → communication IC → semiconductor, and have been the workhorse of point-to-point PC serial ports since the 1980s. Charge-pump-based transceivers like the MAX232 family made the standard practical by removing the need for a dual-polarity power rail. Key features of the MAX232EPE+ include: integrated charge pump with internal ±10V generation, compatibility with all EIA/TIA-232E and V.28/V.24 interfaces, ESD protection on RS-232 pins, and low-power CMOS construction. The 16-PDIP package suits through-hole designs, breadboarding, and legacy equipment maintenance where SMD parts are not desirable. The device uses a dual charge-pump (voltage doubler and inverter) topology: the doubler boosts +5V to +10V using external capacitors, and the inverter produces -10V, yielding ±10V swing across each transmitter output. Receivers invert TTL/CMOS levels back to 5V logic. This architecture makes the MAX232 family ideal when a single +5V rail is available and ±12V cannot be provided. Typical applications include legacy PC serial ports, industrial PLCs and HMIs, point-of-sale terminals, embedded microcontroller UART interfaces, barcode scanners, and any system requiring a DB9 or similar RS-232 connection from a 5V logic domain. The extended temperature range suits factory automation environments. When designing with the MAX232EPE+, choose external charge-pump capacitors carefully — 1µF to 10µF ceramic or tantalum types are typical; undersized caps reduce driver output swing. Place the charge-pump caps and bypass cap within a few millimeters of the IC pins to maintain transmitter output compliance. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet, helping engineers select and source the right RS-232 transceiver for legacy 5V designs.

RFC Hubungi kami
MAX232ESE+ - Dual RS-232 Transceiver | Maxim Integrated
MAX232ESE+

MAX232ESE+ - Dual RS-232 Transceiver | Maxim Integrated

The Maxim Integrated MAX232ESE+ is a dual RS-232 line-driver and receiver interface IC operating from a 4.5 V to 5.5 V supply in a 16-pin SOIC package. It provides two transmit channels and two receive channels for systems that cannot directly use ±12 V RS-232 levels. The device supports data rates up to 120 kbps and is designed for EIA/TIA-232E, CCITT V.28, and V.24 communications interfaces. An RS-232 transceiver is an interface IC that converts low-voltage digital logic signals into RS-232-compatible electrical levels and converts incoming RS-232 signals back into logic-compatible levels. Within the broader hierarchy of interface ICs, transceiver ICs connect processor or controller logic to communication ports. The MAX232 family is especially useful where a positive single supply is available but the external line requires bipolar RS-232 voltage levels. The MAX232ESE+ uses CMOS circuitry and includes the charge-pump circuitry required to generate the bipolar levels used by the RS-232 drivers. Two driver outputs support transmit channels, while two receiver inputs support receive channels. Its stated operating supply range of 4.5 V to 5.5 V supports conventional +5 V digital systems. The manufacturer describes the family as particularly suitable for battery-powered equipment because a shutdown mode can reduce power consumption when the interface is not active. Its principal application is point-to-point serial communication between a host controller and an external RS-232 device. Typical examples include industrial control terminals, data-acquisition equipment, service interfaces, and legacy peripheral connections. At data rates up to 120 kbps, the device accommodates many legacy asynchronous serial protocols while operating from a single 5 V rail. A 120 kbps capability should not be confused with the much higher data rates sometimes associated with USB-to-serial converters. Circuit design requires correct treatment of RS-232 signal levels, including ground reference and, where cable length or noise conditions require it, protection for the external interface. Charge-pump capacitors must be connected exactly as shown in the manufacturer’s recommended application circuit. Keep the charge-pump and communication traces away from sensitive analog inputs, and verify the logic levels and connector-side protection before releasing a board. This page combines the manufacturer interface specifications, package information, application guidance, and verified cross-reference findings in a format intended for schematic review and sourcing decisions. It also distinguishes pin-compatible alternatives from options that require different packages or electrical changes, helping engineers assess replacement risk before modifying a PCB.

RFC Hubungi kami
MAX232ESE+T - 120kbps RS-232 Transceiver | Analog Devices
MAX232ESE+T

MAX232ESE+T - 120kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX232ESE+T is a +5 V-powered, two-driver and two-receiver RS-232 transceiver packaged in a 16-pin SOIC. It supports data rates up to 120 kbps and implements EIA/TIA-232E and V.28/V.24-compatible communications interfaces. Its integrated capacitive voltage generator produces the bipolar RS-232 voltage levels required by the driver outputs from a single 5 V supply, avoiding a separate negative power rail. An RS-232 transceiver is an interface IC that combines a transmitter and receiver in one package. A line driver converts logic-level signals into differential, bipolar RS-232 signals, while a line receiver converts bipolar signals back into logic levels. The MAX232ESE+T belongs to the broader RS-232 interface transceiver category, where EIA/TIA-232E, V.28, and V.24 define the electrical behavior and communication characteristics of the interface. The device includes two transmit channels and two receive channels in a 16-pin SOIC. According to the manufacturer product page, the MAX232E family meets EIA/TIA-232E and CCITT V.28 specifications at data rates up to 120 kbps when loaded. This makes the part suitable for legacy serial ports, industrial equipment, service interfaces, and embedded systems that retain an RS-232 connection. The MAX232ESE+T combines a +5 V supply with on-chip charge-pump circuitry for the negative driver voltage. This integration allows the interface to operate without a separate negative supply, while the capacitive charge pump adds only a small number of external charge-pump capacitors. The E designation denotes the enhanced MAX232 family, while the suffix identifies the package, temperature option, and lead-free tape-and-reel shipping configuration. Typical uses include RS-232 links between industrial controllers and service equipment, configuration ports on network appliances, legacy printer and instrument interfaces, and diagnostic connections on embedded systems. Designers should treat the RS-232 driver outputs as not tolerant of the negative voltages found on telephone lines, and they should provide the charge-pump and interface capacitors specified by the manufacturer. For PCB layout, place the charge-pump capacitors and VCC bypass capacitor close to their associated device pins, and route each driver output directly to its RS-232 connector. Keep logic-side traces away from the higher-voltage driver outputs to reduce capacitive coupling and data errors, especially when long connector cables are attached. This product page combines the manufacturer’s device description, distributor package identification, lifecycle information, replacement analysis, and practical RS-232 layout guidance. It is intended to help engineers verify electrical fit, package compatibility, sourcing requirements, and board-level implementation before committing a MAX232ESE+T to a new or existing design.

RFC Hubungi kami
MAX232EWE+ - Dual RS-232 Transceiver, 5V | Maxim
MAX232EWE+

MAX232EWE+ - Dual RS-232 Transceiver, 5V | Maxim

The Maxim Integrated MAX232EWE+ is a +5 V-powered, dual RS-232 transceiver with two drivers and two receivers, a maximum data rate of 120 kbps, and a 4.5 V to 5.5 V supply range. The device is packaged in a 16-pin SOIC and is designed for bidirectional RS-232 level translation between a modern CMOS or TTL-based system and an RS-232 port. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. In the product hierarchy, the MAX232EWE+ is a dual line transceiver within the broader RS-232 interface IC and semiconductor categories. Its two driver and two receiver channels allow one connector to carry two independent RS-232 data paths, reducing the number of interface components required in multi-channel equipment. The principal operating characteristics are a 4.5 V to 5.5 V supply range, 120 kbps maximum data rate, two transmitters, two receivers, CMOS-compatible logic, and a 16-pin SOIC package. The E in the EWE package code identifies the manufacturer’s specified package variant, while the plus suffix denotes the current ordering designation shown in the product listings. The wide SOIC package measures 7.50 mm across the width dimension stated in the product record. The MAX232 family uses integrated charge-pump circuitry to generate the positive and negative voltage levels required by RS-232. Those levels allow the interface to overcome the voltage thresholds and noise margin associated with unbalanced, single-ended communications. Because the device includes both transmit and receive functions, each logical channel can use one driver and one receiver when full-duplex point-to-point communication is required. Typical uses include industrial serial-control equipment, test and measurement instruments, data acquisition systems, point-of-sale terminals, and embedded control systems that expose an RS-232 port. It is most appropriate where a legacy RS-232 interface must coexist with a 5 V CMOS or TTL control platform. USB-to-RS-232 conversion is another possible use when the host controller already provides UART-compatible logic signals. PCB layout should keep the interface and charge-pump components close to the device and should route the RS-232 traces away from sensitive analog and high-speed digital signals. Decoupling capacitors must follow the capacitor-selection and layout guidance in the manufacturer datasheet. Before substituting a different transceiver, verify the complete pinout, supply range, driver and receiver counts, maximum data rate, logic thresholds, and connector-side voltage levels rather than relying on package dimensions alone. This page organizes the MAX232EWE+ specifications, practical design considerations, application guidance, and qualified drop-in alternatives into an engineering-focused reference. It also distinguishes the known channel, speed, voltage, and package characteristics from parameters that require confirmation in the manufacturer datasheet before production release.

RFC Hubungi kami
MAX232EWE+T - 120kbps 5V RS-232 Transceiver | Maxim
MAX232EWE+T

MAX232EWE+T - 120kbps 5V RS-232 Transceiver | Maxim

The Maxim Integrated MAX232EWE+T is a +5 V-powered, dual-driver and dual-receiver RS-232 transceiver supporting data rates up to 120 kbps in a 16-pin wide SOIC package. It provides two transmit channels and two receive channels for bidirectional serial interfaces while generating the positive and negative voltages required by RS-232 from a single 5 V supply. An RS-232 transceiver is an interface IC that converts low-voltage CMOS or TTL logic signals into RS-232 levels and converts incoming RS-232 signals back into logic-compatible levels. It belongs to the interface IC hierarchy and is commonly placed between a host controller, microcontroller, or data-processing equipment and an external RS-232 port. Unlike a direct TTL connection, the MAX232EWE+T adds voltage-level translation, noise tolerance, and standard-compliant line signaling. The device supports a 4.5 V to 5.5 V supply range and data rates up to 120 kbps. Its two drivers and two receivers are intended for EIA/TIA-232E, V.28, and V.24 interfaces. The integrated charge-pump circuitry eliminates the need for an external positive supply, while external capacitors provide the voltage multiplication and supply filtering required by the device. The MAX232 family uses bipolar charge-pump circuitry to translate a 5 V input into approximately positive and negative RS-232 output levels. Receiver inputs are designed to detect the corresponding negative-going RS-232 signals, while the drivers provide the required level shifting and signal conditioning. Because the interface operates through voltage conversion rather than differential signaling, it is intended for point-to-point RS-232 connections rather than long multidrop networks. Typical uses include serial service ports, industrial control links, configuration interfaces, test equipment, and legacy peripheral connections. Two transmit and two receive channels can support one hardware handshake flow or two independent unidirectional links. The 120 kbps capability also makes the device suitable for moderate-rate data links where legacy RS-232 equipment must interoperate with newer control electronics. PCB design should place the charge-pump capacitors close to their associated pins and keep the RS-232 connector interface path away from sensitive analog or high-speed digital traces. Protection components may be added at exposed connector pins, but their capacitance and clamping voltage must be checked so they do not impair receiver detection or driver operation. This product page combines the manufacturer interface specifications with practical PCB guidance, application-oriented design context, and a package-focused comparison. It helps engineers distinguish the wide-SOIC MAX232EWE+T from temperature-grade, packing-code, narrow-SOIC, and functionally similar interface devices that may not be drop-in replacements for an existing layout.

RFC Hubungi kami
MAX232EWE.C70401 - 120kbps RS-232 Transceiver | Analog Devices
MAX232EWE.C70401

MAX232EWE.C70401 - 120kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX232EWE.C70401 is a +5 V-powered, 2-transceiver RS-232 interface IC housed in a 16-pin SOIC package. It supports data rates up to 120kbps and meets EIA/TIA-232E and CCITT V.28 specifications when loaded. The device provides two driver and two receiver channels for translating logic-level signals between an RS-232 port and a digital controller. An RS-232 transceiver is an interface IC that bridges a computer or embedded system with a serial port by converting logic-level voltages to and from RS-232 signal levels. In the product hierarchy, the MAX232EWE.C70401 belongs to the interface IC family, then to the RS-232 driver and receiver class, and ultimately to the broader semiconductor category. It is useful where a modern controller lacks native RS-232 electrical interfaces. The principal features include two transmit drivers, two receive receivers, operation from a +5 V supply, and support for data rates up to 120kbps. Its 16-pin SOIC package supports compact surface-mount assembly. The manufacturer identifies compliance with EIA/TIA-232E and CCITT V.28 specifications when the interface is loaded, making it applicable to conventional RS-232 equipment, control systems, instrumentation, and industrial data links. The MAX232 family uses charge-pump circuitry to develop the bipolar voltage swings required by RS-232 from a single +5 V supply. This architecture allows the IC to operate with a single positive rail while presenting logic-compatible signals to the connected controller. Although the product page groups the MAX232E among its multichannel RS-232 driver and receiver devices, it specifically identifies the MAX202E and MAX232E as available in 16-pin TSSOP, narrow SO, wide SO, and DIP package options. Typical uses include connecting a 5 V microcontroller or processor to a legacy RS-232 console, instrumentation interface, maintenance port, or industrial controller. The two-driver and two-receiver arrangement supports two communication channels in one package. The maximum specified data rate of 120kbps exceeds common serial-console rates, although the complete link must also satisfy the timing and signal-integrity requirements of the connected equipment. PCB implementation should follow the manufacturer's pin description and recommended decoupling arrangement exactly. Keep the charge-pump and interface layout shown in the datasheet, provide the specified supply capacitance, route RS-232 driver outputs away from sensitive analog nodes, and account for the higher voltage and current on the cable side of the interface. The complete pin assignment should be taken from the package drawing because the exact exposed-pad and no-connect details must match the ordered package variant. This page combines the exact manufacturer interface specifications, ordering information, package data, sourcing links, and practical application guidance. It also identifies genuine same-family alternatives while distinguishing verified drop-in choices from options that require package or design revalidation.

RFC Hubungi kami
MAX232ID - 120kbps Dual RS-232 Transceiver | Texas Instruments
MAX232ID

MAX232ID - 120kbps Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232ID is a dual-channel RS-232 line-driver and receiver IC that operates up to 120 kbit/s from a single 4.5 V to 5.5 V supply. The device provides two drivers and two receivers, generates the required bipolar RS-232 voltage levels with external charge-pump capacitors, and is housed in a 16-pin SOIC package. Its drivers support plus or minus 9 V output levels, while the receivers tolerate plus or minus 30 V input levels. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 electrical levels and converts received RS-232 signals back into logic levels. Within the interface hierarchy, it is an RS-232 transceiver, an interface IC, and a semiconductor used to bridge TTL or CMOS equipment with a serial communications bus. The MAX232ID is specifically associated with conventional TIA/EIA-232-F and ITU V.28 signaling rather than low-voltage differential protocols such as RS-485. Key features include two RS-232 drivers, two RS-232 receivers, operation from one 5 V supply, and a maximum data rate of 120 kbit/s. External 1 uF charge-pump capacitors are required to generate the bipolar transmitter supply. The receiver section supports plus or minus 30 V input levels, improving tolerance to transient voltages commonly encountered on longer cable runs. Typical supply current is listed as 8 mA in the verified source data. The MAX232ID implements the electrical conversion required at the boundary between a digital controller or UART and an RS-232 port. Because the drivers actively produce RS-232-level voltages, the circuit does not require a separate external RS-232 line driver. Conversely, the receivers convert incoming bipolar signals into a digital voltage compatible with the host logic supply. The complete device therefore consolidates both directions of a two-channel serial interface into one IC. Typical applications include industrial serial consoles, data acquisition equipment, laboratory instruments, point-of-sale systems, embedded control systems, and legacy computer peripherals. The 120 kbit/s operating limit suits conventional serial ports and short-distance point-to-point links. It is also appropriate for troubleshooting and repair systems that must remain compatible with equipment using full-strength RS-232 rather than low-voltage variants. Designers must follow the charge-pump capacitor recommendations and provide the required bypassing on the 5 V rail. Protection, grounding, cable length, and connector selection remain external system considerations. The MAX232ID does not replace the transceiver with an RS-485 or USB interface, and its electrical compatibility should be verified against the connected equipment before substitution. This page consolidates verified manufacturer and distributor information, same-package alternatives, pricing data, and practical engineering guidance. It distinguishes true SOIC-16 drop-in candidates from functional alternatives and highlights the electrical checks required when replacing an RS-232 transceiver.

RFC Hubungi kami
MAX232IDG4 - Dual 120kbps RS-232 Transceiver | Texas Instruments
MAX232IDG4

MAX232IDG4 - Dual 120kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232IDG4 is a dual RS-232 line-driver and receiver interface IC supporting data rates up to 120 kbit/s from a single 5 V supply. The device provides two transmit channels, two receive channels, approximately ±9 V driver output levels, and ±2 kV ESD protection in a 16-pin SOIC package. Its specified temperature range is -40 °C to 85 °C. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts incoming RS-232 signals back into digital logic. Within the broader hierarchy, the MAX232 is a serial-interface transceiver, placing it under interface ICs and data-conversion components used to connect computer, industrial-control, and embedded systems to older RS-232 equipment. The MAX232IDG4 implements the EIA-232 and V.28 signaling requirements described by the manufacturer. Its dual-channel architecture allows one package to serve two RS-232 ports. A charge-pump circuit generates the positive and negative voltages required by the drivers from one 5 V supply, eliminating the need for a separate bipolar supply. The charge-pump network requires 1.0 µF capacitors. Key electrical features include ±30 V receiver input levels, 120 kbit/s operation, and low supply current with a typical value of 8 mA. The driver output swing reaches approximately ±9 V, while the receiver converts the RS-232 line voltage into CMOS-compatible logic. The integrated ESD protection is specified at ±2 kV, making the interface suitable for equipment where cables can introduce electrostatic discharge. Typical uses include industrial controller serial ports, configuration interfaces on embedded systems, test and measurement equipment, and service connections for legacy computer peripherals. Because RS-232 is a point-to-point, unbalanced standard, the MAX232IDG4 is best placed between a host UART and a protected external connector rather than used as a multi-drop network interface. The main design consideration is charge-pump capacitor and connector layout. Place the 1.0 µF capacitors close to the charge-pump pins, route driver outputs and receiver inputs away from sensitive digital signals, and provide the connector-side protection and chassis-ground strategy required by the target equipment standard. Confirm signal levels and polarity in the system firmware or hardware interface before deployment. This product page combines manufacturer specifications, verified price evidence, strict same-package replacement options, and practical interface-layout guidance to support component selection, PCB reuse, and robust RS-232 implementation.

RFC Hubungi kami
MAX232IDR - 120 kbps Dual RS-232 Transceiver | Texas Instruments
MAX232IDR

MAX232IDR - 120 kbps Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232IDR is a 5 V dual-channel RS-232 line transceiver with two drivers and two receivers, a maximum data rate of 120 kbit/s, and a 16-pin SOIC package. Its integrated charge-pump circuitry develops the positive and negative voltages required by the EIA-232 interface while the device operates from a single 4.5 V to 5.5 V supply. An RS-232 transceiver is an interface IC that converts logic-level signals into bipolar RS-232 levels and converts incoming bipolar signals back into logic levels. Within the interface hierarchy, the MAX232 belongs to the RS-232 transceiver family of interface ICs used to connect modern digital equipment with legacy serial ports. It is especially useful where a UART provides TTL or CMOS logic but the peripheral expects true RS-232 signaling. The MAX232IDR provides two transmit channels and two receive channels, making it suitable for implementing one or two complete point-to-point serial links. Its stated 120 kbit/s operating rate covers standard asynchronous serial communication, while the single-supply design simplifies PCB power planning. The manufacturer also identifies approximately ±9 V driver output levels and ±2 kV ESD protection as principal benefits of the MAX232 family. Internally, the charge-pump voltage converter supplies the bipolar levels required by the drivers. Receivers tolerate RS-232 input levels down to ±30 V, allowing connected equipment to present stronger transients without immediately damaging the receive path. The manufacturer lists low supply current of approximately 8 mA typical, and the device is designed for interchangeability with the classic Maxim MAX232. Typical applications include serial adapters, industrial control consoles, instrumentation, and embedded systems that communicate with RS-232 equipment through a UART. One receiver and driver can form a bidirectional data path when the transmit and receive lines are cross-connected; the second pair provides another channel or additional unidirectional interface. It is also useful when a legacy printer, controller, or service port requires RS-232 rather than TTL levels. Designers should place the charge-pump capacitors close to the IC and route the RS-232 traces away from sensitive analog and high-speed digital signals. Decoupling near VCC reduces supply disturbance, while the receiver’s ±30 V input capability should not be confused with ±30 V output capability: the specified driver output is approximately ±9 V. Cable protection and grounding remain necessary for reliable operation with external equipment. This page combines the manufacturer’s electrical specifications, ordering information, package details, cross-reference results, and practical implementation guidance. It also identifies same-footprint alternatives and explains the electrical distinctions that should be checked before replacing the MAX232IDR in an existing design.

RFC Hubungi kami
MAX232IDRG4 - 120kbit/s Dual RS-232 Transceiver | Texas Instruments
MAX232IDRG4

MAX232IDRG4 - 120kbit/s Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232IDRG4 is a dual EIA-232 driver and receiver with two transmit channels, two receive channels, a maximum data rate of 120 kbit/s, and a 16-pin SOIC package. It operates from a single 5 V supply and uses integrated charge-pump circuitry with 1.0 µF capacitors. The MAX232IDRG4 accepts input levels to ±30 V and provides an 8 mA typical low supply current. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a ±RS-232 physical link. The MAX232 belongs to the transceiver and line-driver hierarchy, where a transmitter translates low-voltage digital signals into RS-232 levels and a receiver converts RS-232 inputs back to logic levels. Its integrated charge pump supplies the positive and negative voltages required by the RS-232 standard without a separate bipolar power supply. Key features include two EIA-232 drivers, two EIA-232 receivers, operation from one 5 V supply, a data rate up to 120 kbit/s, and low typical supply current of 8 mA. The 16-pin SOIC package provides a conventional surface-mount footprint suitable for industrial-control, instrumentation, and embedded communication equipment. Its operating temperature range extends from -40 °C to +85 °C. The charge-pump architecture is central to operation. External capacitors connected to the C1 and C2 pins generate the positive rail used by the drivers, while the receiver side reconstructs the incoming signal referenced to ground. The device supports receiver input levels to ±30 V, providing useful transient headroom for a communication interface exposed to connected equipment or longer cable runs. Typical applications include RS-232 links between microcontrollers and test equipment, industrial controllers communicating with service terminals, configuration interfaces for embedded systems, and instrumentation using legacy serial ports. The dual-channel arrangement can support two independent transmit or receive paths, although a particular RS-232 connection may use only one channel in each direction. PCB design should prioritize short charge-pump capacitor connections and a clean return path. Place the 1.0 µF capacitors close to their designated pins, route the interface ground carefully, and keep unprotected RS-232 conductors away from sensitive clock and analog traces. Firmware must also avoid relying on RS-232 signal levels as a substitute for a formal device handshake. This page combines the MAX232IDRG4 interface specifications, verified distributor listings, same-family drop-in alternatives, and practical PCB guidance. It is designed to help engineers identify suitable replacements, understand the charge-pump implementation, and plan an RS-232 interface before layout and prototype assembly.

RFC Hubungi kami
MAX232IDW - 120kbps Dual RS-232 Transceiver | Texas Instruments
MAX232IDW

MAX232IDW - 120kbps Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232IDW is a dual RS-232 line-driver and receiver transceiver with two transmit channels and two receive channels, a maximum data rate of 120 kbps, and a 16-pin SOIC package. It operates from a single 5 V supply and uses an on-chip capacitive voltage generator to produce RS-232-level output voltages from approximately ±9 V. An RS-232 transceiver is an interface IC that converts logic-level signals between TTL/CMOS equipment and the voltage-defined RS-232 interface. The MAX232 belongs to the RS-232 interface transceiver family, which sits within interface ICs and broader semiconductor communication components. Its integrated charge pump reduces the external component count compared with discrete RS-232 implementations. The device supports data rates up to 120 kbps and includes two drivers plus two receivers for bidirectional serial links. Its receiver can accept input levels up to ±30 V, which provides margin for ±15 V RS-232 signaling and transient conditions. The stated receiver threshold is typically 1.3 V with 0.5 V hysteresis. Texas Instruments identifies ±9 V outputs and ±2 kV ESD protection as principal product features. Because MAX232IDW accepts a 4.5 V to 5.5 V supply, downstream circuitry must already have a compatible 5 V rail. It cannot directly operate from a 3.3 V system supply. The on-chip voltage converter requires external charge-pump capacitors, while normal system design also needs connection protection, grounding, and cable-routing consideration. Its typical supply current is 8 mA, making it suitable for established 5 V industrial, instrumentation, and embedded-control interfaces. Typical uses include legacy RS-232 ports on test equipment, industrial controllers, serial adapters, service interfaces, and embedded systems that communicate with older peripherals. Two driver/receiver pairs support one or more duplex channels without adding separate line-driver ICs. The device is also suited to legacy industrial equipment where RS-232 remains the established service or configuration interface. For a new design, verify that the connector and cable carry RS-232 bipolar voltage rather than RS-485 differential signaling. Place the charge-pump capacitors close to their designated pins and use a low-impedance ground return for reliable receiver operation. If the system supply is 3.3 V, choose a specifically rated 3.3 V-compatible transceiver instead of adding an unnecessary regulator solely for MAX232IDW. This product data combines manufacturer specifications, lifecycle information, and cross-reference results with practical interface-design guidance. The comparison and drop-in guidance distinguish package compatibility from functional similarity, helping engineers avoid substitutions that require PCB changes or revised power-supply and protection schemes.

RFC Hubungi kami
MAX232IDWG4 - 5V 120kbps Dual RS-232 Transceiver | TI
MAX232IDWG4

MAX232IDWG4 - 5V 120kbps Dual RS-232 Transceiver | TI

The Texas Instruments MAX232IDWG4 is a 5 V dual RS-232 line driver and receiver IC supporting data rates up to 120 kbit/s, with two transmitters and two receivers in a 16-pin SOIC package. The interface IC generates approximately ±9 V transmitter output levels from a single 5 V supply and accepts receiver input levels of ±30 V. An RS-232 transceiver is an interface IC that converts logic-level signals between a digital system and RS-232 differential, bipolar signaling lines. The MAX232 belongs to the RS-232 transceiver hierarchy, where transmitters create positive or negative voltage levels for the cable and receivers detect those levels with noise tolerance. This bidirectional interface level is widely used for legacy serial ports, industrial equipment, and service connections. The device includes two RS-232 drivers, two RS-232 receivers, and integrated charge-pump circuitry. Charge-pump capacitors of 1.0 uF support operation from a single 5 V power supply. The maximum data rate is 120 kbit/s, receiver hysteresis is 500 mV, and typical supply current is 8 mA. The Texas Instruments product page also identifies ±9 V output capability and ±2 kV ESD protection. The MAX232 architecture allows one logic-side supply and one ground reference while producing bipolar RS-232 levels at the cable interface. Receiver hysteresis of 500 mV helps distinguish valid signal states around the transition region. The two-channel arrangement supports one full-duplex serial link using two drivers and two receivers, or two unidirectional paths when the channels are allocated independently. Typical uses include PC serial-port emulation, RS-232 equipment interfaces, industrial-control links, test equipment, and legacy peripheral connections. The 16-pin SOIC package is suitable for conventional surface-mount PCB assembly. Because the supply side is 5 V, the circuit requires level-shifting only for the RS-232 cable side; the logic-side pins connect directly to compatible 5 V digital circuits. Designers should place the charge-pump capacitors close to their associated pins, route transmitter outputs as interference-prone RS-232 nets, and maintain suitable return paths for the bipolar signals. The MAX232 is not a 3.3 V-only RS-232 solution, so downstream logic must be compatible with its 5 V interface or require an additional level shifter. This page combines device specifications, verified package information, drop-in replacement guidance, interface design considerations, and practical application guidance to support faster component selection and PCB implementation.

RFC Hubungi kami
MAX232IDWRG4 - Dual RS-232 Transceiver | Texas Instruments
MAX232IDWRG4

MAX232IDWRG4 - Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232IDWRG4 is a dual RS-232 driver and receiver transceiver with two transmit channels and two receive channels, a maximum data rate of 120 kbit/s, and a single 5 V power supply. The device is housed in a 16-pin SOIC package and is intended for industrial-temperature serial-interface equipment. An RS-232 transceiver is an interface IC that translates between complementary TTL/CMOS logic levels and the bipolar voltage levels used by RS-232 links. The MAX232 family combines driver, receiver, and charge-pump circuitry in one package, reducing the number of components required for a conventional asynchronous serial port. Its integrated charge pump generates the positive and negative voltages needed to transmit RS-232 signals from a single 5 V supply. The MAX232IDWRG4 provides two drivers and two receivers, supporting two RS-232 channels when each driver is paired with one receiver. It supports communication rates up to 120 kbit/s, accepts receiver input levels down to -30 V, and operates from one 5 V supply. Four external 1.0 uF charge-pump capacitors are used with the integrated voltage converter. Typical supply current is 8 mA. Each receiver includes the input protection required for handling RS-232 bipolar voltages, while the driver stage provides the voltage swing expected by RS-232 equipment. The MAX232IDWRG4 is specified for industrial temperature operation from -40 C to +85 C and is available in a 16-pin SOIC package. Its eight signal pins divide into four driver inputs, four driver outputs, four receiver inputs, and four receiver outputs. Typical uses include industrial serial consoles, data-acquisition equipment, test and measurement instruments, printer interfaces, and embedded systems that require a compact RS-232 port. Because the transceiver operates from a single 5 V rail, it can be paired directly with 5 V microcontrollers and programmable logic devices without a separate negative supply for the RS-232 interface. When laying out a MAX232IDWRG4 circuit, place the four 1.0 uF charge-pump capacitors close to their associated pins and route the RS-232 connector interface away from sensitive analog and high-speed digital traces. Confirm signal polarity, grounding, and logic levels before connecting the board to another RS-232 system. The device supports 120 kbit/s operation, but cable length, termination, connector quality, and the remote system must also satisfy the requirements of the intended RS-232 application. This product page combines the manufacturer specifications with practical interface-design guidance, verified drop-in alternatives, application-oriented circuit roles, and a parameter comparison for faster component selection.

RFC Hubungi kami
MAX232IN - Dual 120kbps RS-232 Transceiver | Texas Instruments
MAX232IN

MAX232IN - Dual 120kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232IN is a dual EIA-232 driver and receiver interface IC that operates from a single 5 V supply, supports data rates up to 120 kbit/s, and provides +9 V and -9 V RS-232 outputs. The device includes two drivers, two receivers, and an on-chip capacitive voltage generator, and is packaged in a 16-pin PDIP. According to the manufacturer product page, the MAX232 also provides ±2 kV electrostatic-discharge protection on the RS-232 lines. An RS-232 transceiver is an interface IC that converts logic-level signals into voltage levels suitable for a serial communications link. Its hierarchy is transceiver > driver/receiver > interface IC > integrated circuit. The MAX232IN belongs to this category because it bridges a 5 V TTL or CMOS system and a ±9 V RS-232 port. It is useful when a controller, programmable logic, or test system needs bidirectional serial communication over longer distances than a logic-level UART connection can provide. The principal features include two transmit channels, two receive channels, a maximum data rate of 120 kbit/s, receiver input tolerance of ±30 V, and low supply current of 8 mA typical. Its on-chip charge-pump circuit derives the negative RS-232 voltage required by the drivers, so the device needs only one 5 V supply rather than a separate negative supply. The ±2 kV ESD protection rating adds a useful layer of protection for exposed connector-facing pins. The receivers convert RS-232 input voltages to TTL/CMOS logic levels and have a typical threshold of 1.3 V with 0.5 V typical hysteresis. The drivers convert TTL/CMOS logic inputs into RS-232 levels with +9 V and -9 V output capability. The combination of receiver hysteresis and input overvoltage tolerance helps distinguish valid signals from noise, while the dual-channel arrangement allows two RS-232 directions on one device. Typical applications include legacy RS-232 equipment interfaces, industrial controller ports, point-of-sale equipment, data acquisition systems, and service or diagnostic ports. A MAX232IN can connect a 5 V microcontroller UART to a DB9 or equivalent RS-232 connector, provided the board also includes the connector, protection components, grounding strategy, and any required line-conditioning components. The main design consideration is that the MAX232IN is a through-hole PDIP device and its charge-pump network requires the external capacitors specified by the manufacturer. Place those capacitors close to the supply and charge-pump pins, provide an uninterrupted ground path, and confirm signal levels and polarity at the connector. Although the receiver can accept ±30 V inputs, normal RS-232 operation still requires correct common-ground and cable arrangements. This page combines verified manufacturer and distributor information with practical interface guidance, same-package replacement options, parameter comparisons, and design notes for engineers evaluating MAX232IN in legacy RS-232 designs.

RFC Hubungi kami
MAX232INE4 - Dual RS-232 Driver/Receiver 120 kbps | Texas Instruments
MAX232INE4

MAX232INE4 - Dual RS-232 Driver/Receiver 120 kbps | Texas Instruments

Texas Instruments MAX232INE4 is a dual RS-232 driver and receiver interface IC with two driver channels, two receiver channels, a 120 kbps maximum data rate, and a 4.5 V to 5.5 V single supply, packaged in a 16-pin PDIP. The device includes an on-chip charge-pump voltage generator that produces the bipolar voltage levels required by TIA/EIA-232-F from one 5 V supply. An RS-232 interface transceiver is an interface IC that converts low-voltage TTL or CMOS logic signals into RS-232 voltage levels and converts incoming RS-232 signals back into TTL or CMOS levels. Within the hierarchy of interface ICs, transceiver, communications interface, and voltage-level converter, the MAX232INE4 provides bidirectional signal conditioning for data terminals, computers, instrumentation, and embedded control equipment. The device offers two drivers and two receivers in one package, allowing two serial channels to share the same integrated circuit. Its 120 kbps data rate is suitable for conventional asynchronous serial links operating below the RS-232 distance and capacitance limits of the installed cable. The 4.5 V to 5.5 V supply range supports regulated 5 V systems, while the charge pump eliminates the need for a separate negative supply. According to the manufacturer datasheet, each receiver converts TIA/EIA-232-F inputs to 5 V TTL or CMOS levels, has a typical threshold of 1.3 V, provides typical hysteresis of 0.5 V, and can accept inputs up to plus or minus 30 V. The receiver architecture therefore combines useful noise immunity with protection from larger RS-232 transients. Each driver converts TTL or CMOS inputs into RS-232 levels, allowing the same package to support a complete point-to-point serial connection. Typical uses include legacy RS-232 ports, industrial serial controllers, service equipment, data acquisition systems, and embedded systems communicating with computers or test instruments. Because the MAX232INE4 operates from a single 5 V rail, it integrates easily with conventional 5 V logic, although modern mixed-voltage systems may require level-shifting between 3.3 V controllers and the 5 V input threshold of this device. When laying out the circuit, place the charge-pump capacitors and RS-232 interface protection components close to the device pins, and route protected RS-232 traces away from sensitive analog and clock signals. Confirm the driver and receiver logic levels, cable length, baud rate, and grounding arrangement before releasing the layout. For long cables or exposed industrial ports, add the surge and ESD protection appropriate to the installation environment. This product page combines the manufacturer functional specifications, sourcing evidence, replacement cross-references, interface design guidance, and application-specific engineering considerations to support faster component selection and PCB implementation.

RFC Hubungi kami
MAX232MJE/883B - 5V Dual RS-232 Transceiver | Analog Devices
MAX232MJE/883B

MAX232MJE/883B - 5V Dual RS-232 Transceiver | Analog Devices

Analog Devices MAX232MJE/883B is a +5 V-powered, dual RS-232 transceiver containing two line drivers and two receivers in a 16-pin CDIP package. It implements EIA/TIA-232E and V.28/V.24 communications interfaces when a traditional ±12 V supply is unavailable. The device converts logic-level TXD and RIN signals to RS-232 levels and converts incoming RS-232 signals back to CMOS-compatible logic levels. An RS-232 transceiver is a bidirectional interface IC used within the serial communications hierarchy. Its transmitters translate digital logic into single-ended, bipolar RS-232 signals, while its receivers recover logic signals from those physical-layer waveforms. This interface level lies between UART-compatible digital equipment and a DB9 or equivalent connector. The MAX220–MAX249 family was designed specifically for EIA/TIA-232E and V.28/V.24 links where ±12 V is not practical. The MAX232MJE/883B provides two transmit channels and two receive channels from a single 5 V rail. Its +5 V operation simplifies power architecture in embedded systems, while the dual-channel arrangement supports two serial ports or one bidirectional port with spare channels. The /883B designation identifies a screened product variant, making the device relevant to systems that require controlled procurement and qualification rather than only commercial-temperature production. Internally, the MAX232 family uses charge-pump circuitry to develop the positive and negative voltages required by RS-232 drivers. Typical implementation requires external charge-pump capacitors and local supply decoupling close to the device. The transmitter and receiver architecture separates logic-side inputs and outputs from the external cable-facing pins, allowing logic-level equipment to connect through a protected or standardized RS-232 interface. Typical applications include industrial serial consoles, point-of-sale terminals, instrumentation interfaces, embedded data acquisition, and legacy peripheral connections. Two transmitters and two receivers are useful when a controller must communicate with two RS-232 endpoints, or when a design requires two independent transmit-only links alongside receive channels. Cable length, ground reference, protection, and signal polarity must be checked against the interface standard used by the connected equipment. The main layout consideration is to place the required charge-pump and bypass capacitors close to their associated pins. Keep the logic-side traces away from cable-side driver outputs, use a solid ground plane, and place transient-protection components at the connector rather than beside the IC. Account for the voltage and temperature limits of the selected capacitor dielectric before committing to the final component set. This page combines interface specifications, package details, drop-in replacement analysis, and practical PCB guidance. It also distinguishes the screened MAX232MJE/883B from commercial and older grade variants so engineers can make a qualification-aware selection without changing the 16-pin CDIP footprint.

RFC Hubungi kami
MAX232MLP/883B - Dual RS-232 Transceiver | Maxim Integrated
MAX232MLP/883B

MAX232MLP/883B - Dual RS-232 Transceiver | Maxim Integrated

The Maxim Integrated MAX232MLP/883B is a dual-channel RS-232 line transceiver with two transmitters and two receivers, operating from a single 5 V supply. It supports data rates up to 120 kb/s and is packaged in a 20-lead, no-lead ceramic LCC measuring 8.9 mm by 8.9 mm. The /883B ordering designation identifies a military-temperature product variant with a square QCCN package. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 differential voltage levels and converts incoming RS-232 signals back into logic-compatible levels. The MAX232 family belongs to the broader line-driver and line-receiver hierarchy, connecting modern digital control systems with RS-232 equipment through the EIA/TIA-232E and V.28/V.24 interface specifications. The MAX232MLP/883B provides two transmit channels and two receive channels, allowing a complete full-duplex RS-232 port to be implemented with one integrated circuit. Its 120 kb/s maximum data rate is suitable for configuration ports, diagnostic consoles, industrial control links, and service equipment. The single 5 V supply also simplifies system power design compared with older RS-232 implementations requiring positive and negative voltage rails. The MAX232 family uses charge-pump circuitry to generate the positive and negative voltages required by RS-232 line levels from the 5 V supply. Charge-pump capacitors must be connected exactly as shown in the manufacturer datasheet, with suitable ceramic capacitance and effective loop layout. A receive and transmit path can operate simultaneously, supporting full-duplex communication through the integrated dual-channel arrangement. Typical applications include industrial serial adapters, instrumentation interfaces, embedded-service ports, legacy peripheral connections, and data-acquisition equipment. The military-temperature ordering variant is relevant when environmental requirements exceed the standard commercial temperature range. Its 20-terminal ceramic package also differs mechanically from the 16-pin plastic-DIP and narrow-SOIC options offered elsewhere in the MAX232 family. Board design should preserve the charge-pump connection paths and provide appropriate bypass capacitance close to the supply pins. Keep RS-232 signal routing away from sensitive analog or high-speed digital traces, use the specified external capacitors, and observe the absolute maximum ratings for supply and signal voltages. The interface is intended for RS-232 levels, not directly for TTL, CMOS, RS-485, or differential Ethernet signals. This page combines the manufacturer product information, package characteristics, interface functions, and verified ordering information into an engineering-focused guide. It also identifies practical applications, same-footprint family alternatives, and design considerations that help shorten component selection and PCB implementation time.

RFC Hubungi kami
MAX232MWE/PR - Dual RS-232 Transceiver | Analog Devices
MAX232MWE/PR

MAX232MWE/PR - Dual RS-232 Transceiver | Analog Devices

Analog Devices MAX232MWE/PR is a dual RS-232 line transceiver with two transmitters and two receivers, a 5 V supply requirement, and a 16-pin SOIC package. It converts logic-level UART signals to RS-232 levels and converts received RS-232 signals back to logic levels. The MWE/PR configuration is identified as military temperature grade and uses a gull-wing SOP package with 16 terminals. An RS-232 transceiver is an interface IC within the broader line-driver and line-receiver category. Its transmitter side adds the voltage swing and biasing required for RS-232 communication, while its receiver side detects the bipolar voltage levels presented on the cable. A complete dual transceiver is therefore useful where two serial data paths must be supported without using separate single-channel driver and receiver devices. The MAX232MWE/PR provides two full RS-232 channels, operating from a 5 V supply and intended for multipoint or point-to-point RS-232 links. Its military-grade temperature designation makes it relevant to equipment that must tolerate extended environmental conditions. The 16-pin SOIC package supports conventional surface-mount PCB assembly, while its terminal finish is matte tin with an annealed finish and an e3 terminal classification. Its interface architecture provides the required charge-pump and level-shifting functions for bidirectional RS-232 communication. The two transmitters are intended to drive external RS-232 lines, and the two receivers recover data from those lines for the host UART. Engineers should account for external line protection, connector pin assignment, and the power-supply bypass capacitors specified by the manufacturer datasheet when implementing the interface. Typical applications include industrial serial controllers, legacy data-acquisition equipment, embedded service ports, telecom equipment, and RS-232 links between a microcontroller or host UART and an external connector. The same electrical interface can support control, monitoring, configuration, and diagnostic channels when the system already uses RS-232 and does not require a modern differential bus such as RS-485 or LVDS. The main design tradeoff is that this device preserves compatibility with established RS-232 equipment rather than offering the longer reach, common-mode tolerance, and multi-drop capability associated with differential interfaces. Keep the MAX232 supply and ground connections compact, route the cable-side receive nodes away from fast digital signals, and place protection components where the external cable enters the assembly. This page organizes the MAX232MWE/PR interface specifications, package characteristics, verified drop-in alternatives, comparison parameters, and practical PCB guidance. It also identifies commercial information through the page quotation workflow so engineers can evaluate availability without relying on static market pricing.

RFC Hubungi kami
MAX232MWE/PR-T - 5V Dual RS-232 Transceiver | Maxim
MAX232MWE/PR-T

MAX232MWE/PR-T - 5V Dual RS-232 Transceiver | Maxim

The Maxim Integrated MAX232MWE/PR-T is a +5 V powered dual RS-232 transmitter and receiver interface IC packaged in a 16-pin SOIC for surface-mount assemblies. It provides two transmit channels and two receive channels for converting between TTL/CMOS logic levels and EIA/TIA-232 signals. The device supports RS-232 data rates up to 120 kbps and is specified for military temperature-grade applications. An RS-232 interface transceiver is an integrated circuit that combines differential line drivers and receivers with charge-pump voltage conversion. The transmitter converts low-voltage logic signals into RS-232 bipolar levels, while the receiver converts bipolar RS-232 signals back into logic-compatible voltages. This integration allows a digital controller or terminal to communicate over a cable using the RS-232 standard. The MAX232MWE/PR-T offers two drivers and two receivers in one package. Its +5 V operation simplifies designs that already use a 5 V logic supply, while the integrated voltage-generation circuitry avoids a separate external charge-pump supply. The 120 kbps data-rate capability suits legacy serial ports, industrial control equipment, test systems, service interfaces, and embedded systems that still rely on RS-232 rather than modern USB or Ethernet links. The MAX232MWE/PR-T is identified as a 16-terminal, gull-wing, rectangular surface-mount package with a military temperature grade. The -T suffix distinguishes this ordering configuration from related package and qualification variants. Engineers should consult the manufacturer pin-description table before assigning PCB signals, particularly for charge-pump capacitor connections, supply pins, and the driver and receiver channels. In a typical circuit, each driver input connects to a host or peripheral UART, while each receiver output connects to a logic input. Place the required charge-pump capacitors close to their associated pins and route RS-232 traces away from sensitive analog or high-speed digital nets. The receiver inputs must connect only to protected RS-232 signal paths, and unused channels require appropriate termination according to the manufacturer application guidance. This page combines the available manufacturer and distributor identifiers with package, interface, speed, and ordering information. It also highlights practical PCB, signal-integrity, and replacement considerations. Engineers evaluating a migration should confirm pin assignment, electrical limits, temperature range, lifecycle status, and exposed-pad requirements against the manufacturer datasheet rather than relying only on a family-level cross-reference entry.

RFC Hubungi kami
MAX232N - 5V Dual RS-232 Transceiver | Texas Instruments
MAX232N

MAX232N - 5V Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232N is a 5 V dual-channel RS-232 line driver and receiver capable of operating at 120 kbit/s, with ±9 V driver outputs, ±30 V receiver input tolerance, and ±2 kV ESD protection in a 16-pin PDIP package. It provides two drivers and two receivers plus an on-chip capacitive voltage generator, allowing a single 5 V supply to interface TTL or CMOS logic with TIA/EIA-232-F signals. An RS-232 interface transceiver is an interface IC that converts low-voltage digital logic levels into the bipolar voltage levels required by RS-232, then converts received bipolar signals back into TTL or CMOS levels. In the product hierarchy, the MAX232N belongs to the RS-232 transceiver class within interface ICs. The dual-channel architecture supports two simultaneous communication paths, while the integrated voltage generator eliminates the need for a separate negative supply rail. The MAX232N's principal features include support for data rates up to 120 kbit/s, two transmit channels, two receive channels, ±30 V receiver input tolerance, and ±2 kV ESD protection. Its capacitive voltage generator produces the negative voltage required by the RS-232 drivers from a single 5 V supply. The receiver threshold is typically 1.3 V with approximately 0.5 V hysteresis, helping reject noise while resolving valid logic states. The MAX232N combines TTL/CMOS-compatible inputs and outputs with RS-232 line-driver outputs. According to the manufacturer datasheet, the receivers accept signals as high as ±30 V, while the drivers produce approximately ±9 V output levels. This combination is useful when a system must tolerate legacy serial connectors, ground-potential differences, or electrostatic-discharge exposure while maintaining a conventional 5 V logic interface. Typical uses include industrial serial controllers, service equipment, data-acquisition systems, point-of-sale terminals, and legacy computer serial ports. The 120 kbit/s maximum data rate suits asynchronous RS-232 links that operate below high-speed differential-interface rates. The two-driver, two-receiver arrangement can also implement one bidirectional data path and one unidirectional status path, or two lower-speed channels. Designers should provide the charge-pump capacitors specified by the manufacturer and connect the interface connector through protection components suited to the required ESD and surge environment. The device is not a multi-drop RS-232 solution, and cable length, termination, grounding, and logic levels must be checked against the target system rather than inferred only from the 120 kbit/s headline specification. This page consolidates the verified manufacturer and distributor information, same-package replacement guidance, and practical interface-design considerations for engineers evaluating the MAX232N. It also distinguishes documented MAX232N characteristics from package or lead-time details that were not supplied by the retrieved sources.

RFC Hubungi kami