Produk (44,000+)

MAX232NE4 - Dual 120kbps RS-232 Transceiver | Texas Instruments
MAX232NE4

MAX232NE4 - Dual 120kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232NE4 is a dual RS-232 driver and receiver transceiver built for two independent data channels, operating at up to 120 kbit/s from a single 5 V supply. It is packaged in a 16-pin PDIP and includes the charge-pump circuitry and external charge-pump capacitors needed to generate EIA-232 signal levels from a 5 V source. The device accepts input levels up to ±30 V and provides 8 mA typical ESD protection on its driver outputs, with the MAX232 family also specified for ±2 kV human-body-model ESD protection. An RS-232 transceiver is an interface IC that bridges the voltage-domain gap between TTL/CMOS logic and the bipolar, single-ended signal system defined by EIA-232. Within the broader electronics hierarchy, the MAX232NE4 is a line transceiver, which is a communication interface IC used to connect a digital controller or embedded system to a serial port. Two driver channels convert TTL/CMOS inputs into RS-232 levels, while two receiver channels convert RS-232 inputs into logic-compatible signals. Key electrical attributes include a 4.5 V to 5.5 V supply range, two drivers, two receivers, full RS-232 operation, a maximum signaling rate of 120 kbit/s, and ±30 V input-level capability. The integrated charge pump eliminates the need for a negative supply rail. The recommended implementation uses 1.0 uF charge-pump capacitors, which must be installed close to the device to limit loop area and preserve switching performance. The MAX232NE4 is appropriate for legacy RS-232 ports, industrial equipment, service interfaces, and embedded-control systems where a 5 V logic domain must communicate with a PC or peripheral over an RS-232 link. Unlike a modern USB-to-serial converter, it remains a wired, point-to-point interface and requires a host-side UART or another system that already provides serial framing. Designers should confirm the PCB footprint, charge-pump capacitor type, driver slew behavior, and receiver logic thresholds before substitution. The ±30 V input rating improves robustness against exposed or noisy cabling, but it does not remove the need for correct grounding, twisted-pair routing where applicable, and protection against sustained overvoltage events. This page consolidates verified manufacturer and distributor information, identifies only package-compatible cross-reference candidates, and adds application guidance and design cautions that are not summarized on a typical distributor listing.

RFC Hubungi kami
MAX232NG4 - 5V Dual RS-232 Transceiver | Texas Instruments
MAX232NG4

MAX232NG4 - 5V Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232NG4 is a 5 V dual RS-232 line driver and receiver with two transmit channels, two receive channels, full-duplex operation, and a 120 kbps data rate in a 16-pin PDIP package. The device accepts a 4.5 V to 5.5 V supply, generates RS-232 voltage levels from one 5 V rail, converts incoming RS-232 signals to TTL/CMOS logic, and includes ±2 kV ESD protection according to the manufacturer product page. An RS-232 transceiver is an interface IC that bridges the voltage-domain difference between computer serial ports and embedded logic. The MAX232 family combines line drivers, line receivers, and a capacitive charge-pump voltage generator. This hierarchy places it within interface ICs and semiconductor signal-conditioning components, while its EIA/TIA-232-F function makes it useful for legacy serial communication, industrial control, and equipment interfaces. The principal operating characteristics include a 4.5 V to 5.5 V supply range, full-duplex operation, and a maximum signaling rate of 120 kbps. Each receiver converts an RS-232 input to a TTL/CMOS output, with a typical input threshold of 1.3 V, typical hysteresis of 500 mV, and the ability to accept inputs up to ±30 V. The integrated voltage generator avoids a separate ±12 V power supply when only one 5 V rail is available. The MAX232NG4 uses a charge-pump architecture to develop positive and negative RS-232 levels. That architecture simplifies board-level power design but requires the external charge-pump capacitors specified by the manufacturer. The device is intended for through-hole PCB assembly in the 16-pin PDIP package. The MAX232NG4 orderable variant is listed as obsolete, so new production designs should confirm current family options and lifecycle status before committing a BOM. Typical uses include legacy PC serial ports, programmable instrumentation, industrial control interfaces, service consoles, and embedded systems that exchange RS-232 commands with external equipment. The 120 kbps rate is appropriate for conventional serial links rather than high-speed differential networking. For a new board, the related MAX232 family in a surface-mount package may simplify assembly, but changing package construction requires PCB layout and thermal-soldering review. The primary design consideration is preserving the charge-pump capacitor connection and ensuring that connector-side signals and ground routing follow the manufacturer layout guidance. Input and output logic levels must also be checked against the connected host voltage. Because the MAX232NG4 package is obsolete, engineers should treat any replacement search as a lifecycle decision as well as an electrical and pin-compatibility assessment. This page consolidates the verified manufacturer and distributor information with lifecycle context, application guidance, practical design considerations, and a parameter-by-parameter comparison with documented same-package alternatives. It is intended to support engineering selection and sourcing decisions without obscuring the distinction between electrical equivalence and manufacturing-status changes.

RFC Hubungi kami
MAX232NS - 2/2 RS-232 Transceiver, 120 kbps | Texas Instruments
MAX232NS

MAX232NS - 2/2 RS-232 Transceiver, 120 kbps | Texas Instruments

Texas Instruments MAX232NS is a dual RS-232 transceiver with two drivers and two receivers, a maximum data rate of 120 kbps, a 4.5 V to 5.5 V supply range, and a 16-pin SOIC package. Designed for bidirectional serial communication, it converts TTL/CMOS logic levels to TIA/EIA-232-F signal levels and converts received RS-232 signals back to logic levels using one 5 V supply. An RS-232 transceiver is an interface IC within the broader transceiver and interface IC hierarchy. It bridges the voltage-domain difference between a modern digital system and a legacy RS-232 port. The MAX232NS includes an on-chip capacitive voltage generator, so the external circuit requires the specified charge-pump capacitors rather than a separate negative supply. This integration makes it suitable for equipment with a single positive supply rail. Key features include two transmit channels, two receive channels, a 120 kbps maximum data rate, and receiver hysteresis of 500 mV. According to the Texas Instruments datasheet SLLS047N, the receivers have a typical threshold of 1.3 V and can accept input voltages of ±30 V. The device operates from 4.5 V to 5.5 V and is offered here in the commercial-temperature 0 °C to 70 °C range. Technically, the transmitters convert TTL/CMOS inputs into RS-232 levels, while the receivers perform the inverse conversion. The integrated voltage generator produces the bipolar voltage required for RS-232 signaling from the 5 V supply. Receiver hysteresis helps reject noise around the input switching threshold, improving reliability on connections that may pick up interference. The dual-channel arrangement supports two independent RS-232 directions on one board. Typical uses include serial adapters, industrial control links, service equipment, data-acquisition systems, and legacy computer or peripheral connections. A transmit-and-receive pair can support one full-duplex RS-232 port, while the second channel can serve another port or provide an additional direction. The 16-pin SOIC package supports conventional surface-mount PCB assembly and standard automated production lines. The principal design consideration is charge-pump capacitor selection and placement. Use the capacitor values specified by the manufacturer and keep the associated traces short, because long or poorly routed paths can degrade startup behavior and increase supply transients. The supply must also remain within 4.5 V to 5.5 V, and exposed RS-232 inputs require protection appropriate to the installation environment. This page consolidates the verified manufacturer specifications, RS-232 application guidance, source links, and same-package replacement information. It is designed to help engineers identify the correct electrical limits, package, procurement data, and design considerations without relying on assumptions about unverified parameters.

RFC Hubungi kami
MAX232NSR - 2/2 RS-232 Transceiver, 120 kbps | Texas Instruments (Tape & Reel)
MAX232NSR

MAX232NSR - 2/2 RS-232 Transceiver, 120 kbps | Texas Instruments (Tape & Reel)

Texas Instruments MAX232NSR is a dual RS-232 transceiver with two drivers and two receivers, a maximum data rate of 120 kbps, a 4.5 V to 5.5 V supply range, and a 16-pin SOIC package. Designed for bidirectional serial communication, it converts TTL/CMOS logic levels to TIA/EIA-232-F signal levels and converts received RS-232 signals back to logic levels using one 5 V supply. An RS-232 transceiver is an interface IC within the broader transceiver and interface IC hierarchy. It bridges the voltage-domain difference between a modern digital system and a legacy RS-232 port. The MAX232NSR includes an on-chip capacitive voltage generator, so the external circuit requires the specified charge-pump capacitors rather than a separate negative supply. This integration makes it suitable for equipment with a single positive supply rail. Key features include two transmit channels, two receive channels, a 120 kbps maximum data rate, and receiver hysteresis of 500 mV. According to the Texas Instruments datasheet SLLS047N, the receivers have a typical threshold of 1.3 V and can accept input voltages of ±30 V. The device operates from 4.5 V to 5.5 V and is offered here in the commercial-temperature 0 °C to 70 °C range. Technically, the transmitters convert TTL/CMOS inputs into RS-232 levels, while the receivers perform the inverse conversion. The integrated voltage generator produces the bipolar voltage required for RS-232 signaling from the 5 V supply. Receiver hysteresis helps reject noise around the input switching threshold, improving reliability on connections that may pick up interference. The dual-channel arrangement supports two independent RS-232 directions on one board. Typical uses include serial adapters, industrial control links, service equipment, data-acquisition systems, and legacy computer or peripheral connections. A transmit-and-receive pair can support one full-duplex RS-232 port, while the second channel can serve another port or provide an additional direction. The 16-pin SOIC package supports conventional surface-mount PCB assembly and standard automated production lines. The principal design consideration is charge-pump capacitor selection and placement. Use the capacitor values specified by the manufacturer and keep the associated traces short, because long or poorly routed paths can degrade startup behavior and increase supply transients. The supply must also remain within 4.5 V to 5.5 V, and exposed RS-232 inputs require protection appropriate to the installation environment. This page consolidates the verified manufacturer specifications, RS-232 application guidance, source links, and same-package replacement information. It is designed to help engineers identify the correct electrical limits, package, procurement data, and design considerations without relying on assumptions about unverified parameters.

RFC Hubungi kami
MAX249CQH+D - 6-Driver/10-Receiver RS-232 Transceiver | Analog Devices
MAX249CQH+D

MAX249CQH+D - 6-Driver/10-Receiver RS-232 Transceiver | Analog Devices

The Analog Devices (formerly Maxim Integrated) MAX249CQH+D is a +5V-powered multichannel RS-232 line driver/receiver in a 44-pin PLCC (16.59 x 16.59 mm) package with 6 drivers and 10 receivers (6/10 transceiver configuration). It operates from a single +5V supply and integrates internal charge-pump capacitors (no external caps required for the older non-MAX2xx parts), making it suitable for EIA/TIA-232E and V.28/V.24 communications interfaces where +/-12V rails are unavailable, such as portable and embedded equipment running off a single 5V logic supply. An RS-232 transceiver (line driver/receiver, formally a UART-to-EIA-232 interface) translates between CMOS/TTL logic levels used by microcontrollers or UARTs and the higher-voltage (+/-5V to +/-15V nominal) RS-232 signalling required by the legacy serial standard. The MAX249CQH+D's 6-driver / 10-receiver count targets fan-in applications where a host reads many input sources while driving several outputs, and its 120 kbps guaranteed data rate is well matched to legacy PC COM ports, industrial controllers, and point-of-sale terminals. Key features include on-board charge-pump voltage converters that synthesize the RS-232 +/-5V to +/-15V output levels from the single +5V input, low-power shutdown mode, and tri-state receiver outputs for bus sharing. The 44-pin PLCC package fits through-hole and socketed industrial backplanes, while the +D suffix indicates factory dry-pack tape-and-reel packaging for surface-mount placement. Operating temperature range is 0C to +70C (commercial grade, C in the part number). Technically, the MAX249CQH+D is built on a proprietary BiCMOS process that integrates vertical PNP charge-pump switches, low-dropout +5V drivers and +/-15V-tolerant receivers on the same die. The internal charge pump uses four small external 1uF capacitors (or in some family members none) to generate V+ and V- rails. Compared to older RS-232 designs that required +/-12V supplies and large bulk capacitors, this device reduces board area by approximately 80 percent and simplifies power architecture. Guaranteed 120 kbps minimum throughput and 3 kV HBM ESD tolerance on driver outputs support robust industrial deployment. Typical applications include industrial multi-drop RS-232 links, factory-automation controllers with many sensors, embedded point-of-sale and kiosk terminals, multi-channel UART fan-out for instrumentation, and portable test equipment. The 6/10 driver/receiver balance is uncommon among modern RS-232 ICs, making this part valuable for retrofit designs that must keep legacy cabling. When designing with this part, ensure the four charge-pump capacitors (typically 1uF to 22uF, low-ESR ceramic) are placed close to the C1+/C1-/C2+/C2- pins with adequate ground return. The +5V supply must deliver at least 50 mA plus 2 mA per active driver during transitions; inadequate decoupling causes charge-pump ripple that couples into the RS-232 output levels and degrades signal integrity. This page synthesizes current distributor pricing, drop-in alternative guidance, and practical design notes that complement (but do not replace) the Analog Devices MAX249 datasheet.

RFC Hubungi kami
MAX301CSE+ - Dual SPST 35Ω Analog Switch | Analog Devices
MAX301CSE+

MAX301CSE+ - Dual SPST 35Ω Analog Switch | Analog Devices

The Analog Devices (Maxim Integrated) MAX301CSE+ is a precision, dual, high-speed analog switch containing two independent single-pole single-throw (SPST) normally-open (NO) switch channels in a 16-pin SOIC package. Each channel offers a maximum on-resistance of 35 ohms, guaranteed to match within 2 ohms between channels, making it suitable for precision signal routing where channel-to-channel consistency matters. A precision analog switch is a type of bidirectional signal gate within the broader family of analog switches and multiplexers (signal routing ICs within data converters and interface signal chains). Unlike a relay, a solid-state CMOS analog switch switches microsecond-fast with no moving parts, and unlike a digital logic gate, it passes continuous analog signals in both directions with minimal distortion. Switches sit between multiplexers (many channels to one) and simple gates, and are fundamental building blocks of signal conditioning, test, and communication systems. Key features of the MAX301 include low on-resistance (less than 35 ohms guaranteed), channel matching within 2 ohms for gain-consistent switching, high-speed switching for fast signal paths, and a dual-channel SPST NO configuration that lets two independent signals share one IC. The '+' suffix denotes Analog Devices' enhanced (lead-free, RoHS-compliant) manufacturing flow. Architecturally, the MAX301 family uses CMOS switch technology with logic-controlled gate drive, providing flat on-resistance across the analog signal range and low charge injection. The normally-open configuration ensures signals are isolated by default and only connected when the control logic commands it, which is the safe default for test equipment, redundant signal paths, and fault-tolerant routing. Typical applications include audio and video signal routing, precision test and measurement switching matrices, communication-system signal gating, data-acquisition channel isolation, and industrial control signal selection. The dual-channel layout is efficient for stereo signal pairs, differential-pair gating, and redundant-path designs where two switches switch simultaneously or independently. When designing with the MAX301CSE+, keep switch on-resistance in mind when driving low-impedance loads, since 35 ohms in series can introduce gain error in precision dividers. Consult the manufacturer datasheet for supply-voltage ranges, switching-time specifications, and control-logic thresholds before finalizing the design. This page synthesizes distributor availability listings, family cross-reference information, and practical design notes not found in a single manufacturer document, making it a one-stop engineering reference for the MAX301CSE+.

RFC Hubungi kami
MAX303CPE+ - Dual High-Speed SPDT Analog Switch | Analog Devices
MAX303CPE+

MAX303CPE+ - Dual High-Speed SPDT Analog Switch | Analog Devices

The Analog Devices MAX303CPE+ is a precision, dual, high-speed analog switch with two independently controlled single-pole double-throw channels, a maximum on-resistance of 35 ohms, and operation across positive and negative supply voltages. The device is packaged as a 16-pin plastic DIP and provides two normally open and two normally closed switch poles for routing bipolar analog signals. An analog switch is a semiconductor device that connects or disects circuit paths under digital control. Unlike a mechanical relay, it can change state rapidly with low control-signal power and without mechanical contact wear. The MAX303 belongs to the interface-IC hierarchy as a precision analog switch and multiplexer. Its matched channels, low leakage, and low on-resistance make it useful where signal integrity must be maintained during measurement, acquisition, or signal-routing operations. The MAX303CPE+ supports two supply rails, allowing operation from positive to negative voltage when the control input thresholds are compatible with the host logic. Its on-resistance is specified below 35 ohms, and the two channels are guaranteed to match within 2 ohms. These characteristics improve channel-to-channel consistency when the same signal level must be presented to multiple downstream nodes. The device also provides low leakage, reported as below 250 pA at 25°C and below 6 nA at 85°C. Each channel contains one normally open and one normally closed path. This arrangement allows a signal to be routed to one of two destinations, or provides break-before-make behavior when the control state changes. The MAX303 family is designed for precision, high-speed signal switching, where on-resistance variation, off-state leakage, and channel matching can affect measurement accuracy. The exact switching timing, logic levels, and supply limits should be confirmed in the manufacturer data sheet before final circuit release. Typical uses include precision test and measurement systems, automated instrumentation, data-acquisition front ends, sample-and-hold circuitry, and bipolar signal-routing networks. In these systems, the MAX303CPE+ can route a sensor or reference signal between measurement paths while keeping insertion resistance and leakage predictable. Its dual-channel architecture reduces component count when two related signals must be selected independently. PCB layout should preserve short return paths and minimize capacitance around signal and control pins. Keep analog traces away from fast switching clocks and high-current paths, and use a solid ground reference to reduce coupling into the selected channel. Because the part uses a through-hole plastic DIP package, connector and socket accessibility should be checked against mechanical height, cleaning requirements, and assembly-service constraints before releasing the production design. This product page organizes the MAX303CPE+ electrical characteristics, package information, qualified drop-in alternatives, and practical design guidance for engineers evaluating dual SPDT analog switching. It also distinguishes the lead-free MAX303CPE+ ordering code from the closely related MAX303CPE catalog entry while preserving the distinction between verified drop-in interchangeability and merely similar products.

RFC Hubungi kami
MAX3051ESA+ - 3.3V 1Mbps CAN Transceiver SOIC-8 | Maxim
MAX3051ESA+

MAX3051ESA+ - 3.3V 1Mbps CAN Transceiver SOIC-8 | Maxim

The Maxim Integrated MAX3051ESA+ is a +3.3V, 1Mbps, low-supply-current CAN (Controller Area Network) bus transceiver housed in an 8-pin SOIC narrow-body package. It interfaces between a CAN protocol controller and the physical differential bus wires, providing a differential transmit path to the bus and a differential receive path back to the controller. The +3.3V single-supply operation targets modern low-voltage MCUs and ASICs that cannot tolerate the legacy 5V CAN transceivers. A CAN transceiver is the physical-layer (OSI layer 1) interface between a digital CAN controller and the two-wire differential bus. It converts digital transmit/receive logic into differential voltages compliant with ISO 11898, while also providing bus-side ESD protection and common-mode tolerance. The MAX3051 belongs to the Maxim CAN transceiver family (3.3V, low-Iq) which sits inside the broader categories of LIN/CAN/FlexRay transceivers, interface ICs, and finally wired-connectivity semiconductors used in industrial automation, building control, and harsh-environment embedded networks. Key features include a 1Mbps maximum data rate in high-speed mode, programmable slew-rate control for EMI-sensitive networks, and four operating modes: high-speed, slope-control, standby, and shutdown. The shutdown and standby states draw only a few hundred microamps, making the part well suited for battery-backed or sleep-cycling nodes. The bus-side common-mode range spans -7V to +12V, well beyond the ISO 11898 minimum of -2V to +7V, allowing reliable operation in electrically noisy industrial environments with large ground shifts. The MAX3051 is fabricated on a low-power CMOS process with on-chip bus drivers that meet ISO 11898-2 physical-layer signaling. The wide common-mode window, combined with the part's ±6kV HBM ESD rating on the bus pins (per Maxim datasheet), enables robust operation in non-automotive harsh environments such as factory floor nodes, building automation backbones, and motor-drive gateways where ground-potential differences exceed ISO 11898 minimums. Typical applications include industrial CAN nodes (PLC modules, sensor hubs), building-automation networks (BACnet over CAN, HVAC controllers), motor-drive CAN command links, embedded sensor networks, and any 3.3V MCU needing CAN connectivity without the cost or power of an automotive-grade transceiver. The low Iq also suits solar or battery-powered remote nodes. When designing with the MAX3051ESA+, place 100nF supply-bypass capacitors as close as possible to VCC and route the CANH/CANL traces as a tightly-coupled 100-ohm differential pair with characteristic impedance of 120 ohms per ISO 11898. Always include a split-termination network (60 ohms + 4.7nF at each end) to suppress common-mode ringing in long stubs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFC Hubungi kami
MAX306CWI+ - 16:1 Precision Analog Multiplexer | Maxim
MAX306CWI+

MAX306CWI+ - 16:1 Precision Analog Multiplexer | Maxim

The Maxim MAX306CWI+ is a precision, monolithic CMOS analog multiplexer with one 16:1 switch, less than 100 Ω on-resistance, and operation from a single 4.5 V to 30 V supply in a 28-pin wide SOIC package. The device supports bidirectional analog-channel routing and maintains channel-to-channel on-resistance matching within 5 Ω across the specified analog signal range. An analog multiplexer is a switch matrix that connects one of several input terminals to a common output. In the MAX306 family, this switching function forms part of the interface-IC hierarchy: analog switch, multiplexer, signal-routing interface, and ultimately the wider semiconductor and test-and-measurement signal-chain categories. The MAX306 provides a single 16-channel selection arrangement, while the related MAX307 family is identified as a dual 8-channel multiplexer. Low on-resistance is important because every closed switch contributes series resistance that can attenuate the measured or transferred signal. The MAX306/MAX307 family combines a maximum on-resistance of less than 100 Ω with matching within 5 Ω between channels and flatness of no more than 7 Ω over the specified analog signal range. This consistency helps preserve channel-to-channel accuracy in precision signal-routing systems. The device also provides low leakage, with off-state input leakage below 2.5 nA at +85 °C, and fast switching, with transition time below 250 ns. Its improved 44 V silicon-gate process supports extremely low charge injection below 10 pC, reducing the control-signal-induced voltage step that can create errors in sampled analog measurements. ESD protection greater than 2000 V adds handling robustness for the analog terminals. Typical uses include automated test equipment, data-acquisition systems, instrumentation, communication equipment, and precision analog signal selection. The wide-SOIC form factor supports surface-mount assembly while providing 28 pins for the 16-channel multiplexer and its associated control and address functions. Board-level designs still require validation of logic levels, address timing, signal bandwidth, and input protection against the exact operating conditions. For a new layout, route each analog channel as a short, impedance-controlled trace and place the device close to the source or measurement circuitry. Keep digital address and control traces away from sensitive analog paths, observe the specified supply range, and verify transition behavior at the intended clock rate. Confirm the complete pin assignment and exposed electrical limits in the manufacturer datasheet before fabrication. This page combines the manufacturer product information with a focused engineering assessment of switching performance, leakage, charge injection, application fit, and package considerations. It also distinguishes a verified same-package substitute from unavailable alternatives, helping designers assess replacement risk without treating a merely similar multiplexer as a drop-in device.

RFC Hubungi kami
MAX306EQI+ - 16:1 CMOS Multiplexer | Analog Devices
MAX306EQI+

MAX306EQI+ - 16:1 CMOS Multiplexer | Analog Devices

The Analog Devices MAX306EQI+ is a precision 16-to-1 CMOS analog multiplexer with less than 100 ohm on-resistance, channel-to-channel matching within 5 ohm, and a 28-pin PLCC package measuring 11.51 x 11.51 mm. The MAX306 family also supports dual 8-channel operation, low charge injection below 10 pC, and switching transition times below 250 ns. An analog multiplexer is an analog switch network that routes one of several input signals to a common output while minimizing distortion, offset, and switching transients. In the signal-chain hierarchy, it belongs to the analog switch and multiplexer category within interface ICs. This precision CMOS implementation is designed for measurement, control, and instrumentation systems where selecting among closely spaced voltage or current signals requires consistent resistance and predictable switching behavior. Key characteristics include on-resistance below 100 ohm, on-resistance matching between channels within 5 ohm, and variation across the specified analog signal range limited to 7 ohm maximum. Off leakage remains below 2.5 nA at +85 degrees Celsius, while low charge injection below 10 pC helps limit switching disturbances. The device also provides ESD protection greater than 2000 V and uses an improved 44 V silicon-gate CMOS process. The MAX306's multiplexed architecture reduces the number of external signal connections required by a system. A common 16-to-1 arrangement can select one measurement channel for a shared amplifier or converter, while the family's dual 8-channel configuration can support two multiplexed groups. Matching within 5 ohm is particularly useful when channels are calibrated individually or when gain errors must remain predictable across a scan. Typical uses include automated test equipment, data-acquisition systems, industrial process monitoring, laboratory instrumentation, and mixed-signal measurement modules. The sub-250 ns transition time supports higher-rate channel scanning, while low leakage and low charge injection are valuable when handling high-impedance sources, sensor outputs, or precision low-level signals. Designers should verify the control-state truth table, pin assignments, supply requirements, and signal-range limits against the manufacturer datasheet before laying out the PCB. Keeping analog traces short, providing a stable reference and ground plane, and placing decoupling capacitors close to the device can help preserve the low-noise behavior expected from a precision analog multiplexer. This page combines the manufacturer specifications with engineering-focused application guidance, package details, comparison parameters, and replacement analysis. It is intended to help designers select the correct multiplex configuration, recognize meaningful differences among related MAX306 order codes, and plan a PCB-compatible replacement before committing a precision analog signal chain to production.

RFC Hubungi kami
MAX3070EAPD+ - 3.3V 250kbps RS-485/422 Transceiver | Analog Devices
MAX3070EAPD+

MAX3070EAPD+ - 3.3V 250kbps RS-485/422 Transceiver | Analog Devices

Analog Devices MAX3070EAPD+ is a 3.3V full-duplex RS-485/RS-422 interface IC rated for data rates up to 250kbps, with ±15kV ESD protection, fail-safe receiver operation, and hot-swap capability. The device is packaged in a 14-pin PDIP and integrates one driver and one receiver for bidirectional point-to-point or multidrop industrial communication links. An RS-485/RS-422 transceiver is an interface integrated circuit that converts logic-level signals into differential bus voltages and converts received differential signals back into CMOS-compatible logic. These differential interfaces belong to the broader serial-interface IC and industrial-communication hierarchy. Their common-mode tolerance, noise immunity, and fault-safe thresholds help preserve data integrity across cables, connectors, motors, automation equipment, and industrial controllers. The MAX3070EAPD+ operates from a 3.3V supply and combines several protection-oriented features in one transceiver. Its ±15kV ESD rating supports robust connection to external equipment, while fail-safe receiver circuitry provides defined behavior during bus idle, driver disconnect, or shorted-driver conditions. Hot-swap operation permits the device to join a live bus without disruptive initialization, making it useful in systems with removable or field-serviceable communication modules. This member of the MAX3070E through MAX3079E family combines a one-driver, one-receiver arrangement with full RS-485 and RS-422 operation. The 250kbps maximum signaling rate suits moderate-speed control and monitoring links rather than high-bandwidth storage or video networks. Differential signaling reduces susceptibility to common-mode noise relative to single-ended implementations, especially on industrial cables routed near motors, relays, and switching power equipment. Typical uses include industrial automation controllers, programmable-logic-crane controllers, building-control equipment, instrumentation, motor-control interfaces, and isolated or non-isolated industrial data links. The transceiver can also bridge legacy controller UART signals to differential RS-485 equipment. Because the device provides both transmit and receive paths, a full-duplex connection requires two differential pairs and separate driver-enable and receiver-enable control according to the bus architecture. PCB design should preserve controlled differential impedance, minimize stub lengths, and keep the transceiver close to the connector. Place protection devices near the external interface, provide local supply decoupling, and route the logic ground cleanly to the bus-return path. Verify termination, biasing, and enable sequencing against the cable length, node count, and topology used by the target network. This product reference combines the exact MAX3070EAPD+ ratings, package information, interface role, application guidance, drop-in family alternatives, and engineering-focused comparison points to support faster component selection, PCB implementation, and sourcing decisions.

RFC Hubungi kami
MAX3070EASD+ - 3.3V Fail-Safe RS-485/RS-422 | Analog Devices
MAX3070EASD+

MAX3070EASD+ - 3.3V Fail-Safe RS-485/RS-422 | Analog Devices

Analog Devices MAX3070EASD+ is a 3.3 V RS-485/RS-422 interface transceiver with one driver and one receiver, ±15 kV ESD protection, fail-safe receiver operation, and hot-swap capability in a 14-pin SOIC package. It is designed for bidirectional industrial data links requiring reliable operation when bus drivers are disabled, disconnected, shorted, or replaced. An RS-485/RS-422 transceiver is an interface IC that converts digital logic signals into differential bus voltages and converts returning differential signals into logic levels. The MAX3070E family belongs to the RS-485/RS-422 interface IC category, supporting industrial communications, data acquisition, instrumentation, and control systems where noise immunity and deterministic bus behavior are important. The MAX3070EASD+ combines a 3.3 V operating supply with ±15 kV ESD-protected bus terminals. Its fail-safe circuitry produces a receiver logic-high output when receiver inputs are open or shorted, avoiding an indeterminate receiver state when all transmitters are disabled. The hot-swap feature further supports systems where a transceiver may be connected to an active bus without disrupting communication. The device contains one driver and one receiver, allowing a full-duplex RS-422 connection or a half-duplex RS-485 connection when the driver and receiver directions are managed appropriately. Its differential interface is suited to industrial environments where common-mode voltage, ground offsets, and electrostatic discharge can degrade single-ended logic links. The SOIC-14 package supports conventional surface-mount assembly and compact board placement. Typical applications include industrial RS-485 sensor networks, factory-floor equipment interfaces, building automation controllers, remote instrument links, and data-acquisition systems. The fail-safe and hot-swap functions are especially useful in bus architectures where nodes may be powered on or off at different times. RS-422 wiring is preferred for point-to-point full-duplex links, while RS-485 permits multi-drop buses when termination and biasing are designed correctly. PCB design should preserve the differential signal path, provide the supply and bypass capacitance required by the manufacturer data sheet, and place protection components close to the connector. Keep the ground reference continuous beneath the interface and route driver and receiver differential pairs together to avoid converting common-mode noise into differential errors. This page combines the manufacturer’s stated interface capabilities, package information, lifecycle context, cross-part comparisons, and practical bus-layout guidance. It is designed to help engineers identify whether the MAX3070EASD+ fits an existing RS-485 or RS-422 design before completing footprint, protection, termination, and sourcing reviews.

RFC Hubungi kami
MAX3070EEPD+ - 3.3V Fail-Safe RS-485 Transceiver | Analog Devices
MAX3070EEPD+

MAX3070EEPD+ - 3.3V Fail-Safe RS-485 Transceiver | Analog Devices

Analog Devices MAX3070EEPD+ is a 3.3V RS-485/RS-422 half-duplex transceiver with one driver, one receiver, a 250 kbps data rate, and a 14-pin PDIP package. It provides ±15 kV ESD protection, fail-safe receiver operation, and hot-swap capability. The device operates from a 2.97 V to 3.63 V supply and is intended for industrial communications equipment. An RS-485/RS-422 transceiver is an interface IC that converts between digital logic signals and balanced differential bus signals. The MAX3070EEPD+ belongs to the interface transceiver hierarchy, combining a line driver, line receiver, protection circuitry, and fail-safe logic in one package. Balanced signaling improves noise immunity and permits reliable data transfer over longer cable runs than single-ended interfaces in electrically noisy environments. The principal features are a 3.3 V operating supply, one-driver/one-receiver configuration, and a maximum data rate of 250 kbps. The ±15 kV ESD rating helps protect the bus-facing pins from electrostatic discharge encountered during installation or maintenance. Fail-safe circuitry guarantees a logic-high receiver output when the receiver inputs are open or shorted, avoiding an indeterminate logic state on an idle or faulted bus. The MAX3070EEPD+ is designed for RS-485 and RS-422 networks that require a low-noise, fault-tolerant differential interface. Its one-driver, one-receiver organization can support half-duplex communication when the direction of data flow is controlled by an external transceiver-enable circuit. The device also supports hot-plug behavior, which is useful in systems where an attached node may connect or disconnect while the bus is active. Typical applications include industrial sensor networks, factory automation equipment, building-control systems, data acquisition units, instrument interfaces, and embedded serial links. A 3.3 V microcontroller or processor can use the transceiver to connect a logic-level UART to a field bus while receiving differential bus signals through the receiver channel. Designers should confirm the receiver and driver enable polarity, bus termination, grounding, and connector arrangement before layout. The ±15 kV protection rating applies to specified ESD conditions; it does not replace surge protection for the complete installation. Keep the ground reference consistent across connected equipment and use twisted-pair wiring for the differential bus. This page consolidates device specifications, package and application guidance, parameter comparisons, and engineering design notes into a focused engineering reference for selecting and implementing the MAX3070EEPD+ in 3.3 V RS-485 and RS-422 systems.

RFC Hubungi kami
MAX3070EESD+ - 3.3V RS-485/RS-422 Transceiver | Maxim Integrated
MAX3070EESD+

MAX3070EESD+ - 3.3V RS-485/RS-422 Transceiver | Maxim Integrated

The Maxim Integrated MAX3070EESD+ is a 3.3 V RS-485/RS-422 interface transceiver featuring one driver, one receiver, ±15 kV ESD protection, fail-safe operation, and hot-swap capability in a 14-pin SOIC package. Its combination of RS-485 and RS-422 support makes it suitable for industrial communication links that require robust differential signaling. An RS-485/RS-422 transceiver is a line-interface IC that converts between single-ended logic signals and differential physical-layer signals. It belongs to the interface IC hierarchy within integrated circuits and combines a differential line driver, a differential receiver, and protection circuitry. Differential signaling improves noise immunity by representing information as the voltage difference between two conductors rather than the voltage referenced only to ground. Key features include a 3.3 V supply, ±15 kV ESD protection, fail-safe receiver behavior, and hot-swap capability. The fail-safe circuit guarantees a logic-high receiver output when receiver inputs are open or shorted, helping prevent uncontrolled bus states. The device also supports both RS-485 and RS-422 applications through its one-driver, one-receiver configuration. Technically, the MAX3070E family combines low-power 3.3 V operation with protected communication interfaces. The differential driver communicates over long cable runs, while the receiver distinguishes the intended differential signal from common-mode noise. ESD protection is especially important in industrial environments where cables can be connected or disconnected while the equipment remains powered. Typical uses include industrial RS-485 buses, factory automation equipment, building-control systems, instrumentation links, and isolated or non-isolated communication interfaces. The 14-pin SOIC package is suitable for conventional surface-mount PCB assembly, while the extended industrial temperature range supports operation from -40°C to 85°C. Designers should verify the complete pinout, termination requirements, driver enable timing, and supply decoupling against the manufacturer datasheet before layout. A controlled-impedance or properly terminated differential pair is important for reliable field-bus operation, and exposed connector routes may require additional board-level ESD protection. This product data combines manufacturer information, current distributor observations, verified alternatives, package details, and application-oriented engineering guidance. It also distinguishes confirmed target-device facts from parameters that still require datasheet verification, helping procurement and design teams make more reliable decisions.

RFC Hubungi kami
MAX3070EESD+T - 3.3V RS-485/RS-422 Transceiver | Analog Devices
MAX3070EESD+T

MAX3070EESD+T - 3.3V RS-485/RS-422 Transceiver | Analog Devices

Analog Devices MAX3070EESD+T is a 3.3V full-duplex RS-485/RS-422 interface transceiver with one driver, one receiver, ±15kV ESD protection, fail-safe receiver operation, and hot-swap capability in a 14-pin narrow SOIC package. Its 2.97V to 3.63V supply range supports low-voltage industrial and embedded communication systems. An RS-485/RS-422 transceiver is an interface IC that converts between digital logic signals and balanced differential bus signals. It belongs to the transceiver hierarchy within interface ICs, connecting UART, microcontrollers, and industrial controllers to long, noise-resistant differential buses. RS-422 emphasizes point-to-point, full-duplex communication, while RS-485 supports multidrop buses and half-duplex operation depending on how the driver enable is controlled. The MAX3070E family combines a 250kbps-class RS-485/RS-422 interface with protective and operational features intended for industrial environments. ±15kV ESD protection improves tolerance of electrostatic discharge on bus-facing pins. Fail-safe receiver circuitry guarantees a logic-high receiver output when the receiver inputs are open or shorted, avoiding an indeterminate logic state on a disconnected bus. Hot-swap support allows the device to tolerate connection to a powered bus. The transceiver uses separate driver and receiver paths for full-duplex communication. The MAX3070EESD+T operates from a 2.97V to 3.63V supply, making it appropriate for 3.3V systems where a 5V interface device would exceed the permitted supply range. Its one-driver, one-receiver arrangement maps naturally to four-wire RS-422 links and can also support half-duplex RS-485 designs when the bus implementation and enable control are configured accordingly. Typical uses include industrial serial links, building automation, process-control equipment, instrumentation, POS terminals, and factory data-acquisition systems. The balanced differential bus reduces susceptibility to common-mode noise relative to single-ended communication, while fail-safe operation improves system behavior during cable faults or disconnected nodes. Designers should preserve the transceiver’s specified supply voltage, termination, protection-network, and common-mode limits. Place the device close to the bus connector, provide a low-impedance ground reference, and follow the manufacturer’s pin-description table and recommended interface circuit. This page also organizes practical application guidance, comparison parameters, and sourcing information around the exact MAX3070EESD+T ordering code. This page provides a concise engineering synthesis of the MAX3070EESD+T interface function, operating constraints, application fit, and design considerations. It translates the manufacturer’s product information into selection guidance for engineers evaluating a robust 3.3V differential bus transceiver.

RFC Hubungi kami
MAX3076EESD+T - 16Mbps RS-485/RS-422 3.3V Transceiver
MAX3076EESD+T

MAX3076EESD+T - 16Mbps RS-485/RS-422 3.3V Transceiver

The Analog Devices MAX3076EESD+T is a 3.3V RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 16 Mbps, and ±15 kV ESD protection in a 14-pin narrow SOIC package. It adds fail-safe receiver behavior and hot-swap capability for robust industrial communication links. The device operates from a 2.97 V to 3.63 V supply, making it suitable for 3.3 V embedded systems. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential bus signals and converts received differential signals back into CMOS-compatible logic. These differential interfaces belong to the broader wired-communication and interface-IC hierarchy. Their common-mode rejection and balanced signaling improve noise immunity over longer cables compared with single-ended interfaces, particularly in industrial environments containing motors, relays, and switching equipment. Key features of the MAX3076EESD+T include ±15 kV ESD protection, fail-safe receiver outputs that remain logic-high when inputs are open or shorted, and hot-swap support for connection to an active bus. The 16 Mbps maximum data rate supports both high-speed point-to-point RS-422 links and moderately high-speed RS-485 networks. The 14-pin narrow SOIC is a surface-mount package suitable for compact, space-constrained equipment. The MAX3070E through MAX3079E family provides closely related interface options. According to the Analog Devices product page, these 3.3 V devices feature one driver, one receiver, fail-safe circuitry, and ESD protection. Exact propagation-delay, receiver-threshold, and driver-loading values must be confirmed against the manufacturer datasheet before high-speed or network-specific design signoff. Typical uses include industrial sensor networks, building-automation equipment, motor-control interfaces, data-acquisition equipment, and isolated or non-isolated telemetry links. For RS-485 multidrop networks, biasing, termination, cable length, and topology must be engineered for the intended data rate. The 3.3 V supply also simplifies connection to low-voltage processors, FPGAs, and transceivers. Designers should protect the bus pins with an appropriate surge and ESD strategy, provide adequate supply decoupling, and verify receiver thresholds when nodes may be disconnected. A 120-ohm termination resistor is commonly used at appropriate cable ends, but its use depends on topology, cable impedance, and signal integrity testing. Hot-swap support does not remove the need for controlled bus connection. This page consolidates verified distributor data, manufacturer information, same-family alternatives, and practical RS-485 design guidance. It helps engineers compare replacement options while preserving the important distinctions among package, data rate, protection, and bus behavior.

RFC Hubungi kami
MAX3078EESA+ - 3.3V RS-485/RS-422 ESD Transceiver
MAX3078EESA+

MAX3078EESA+ - 3.3V RS-485/RS-422 ESD Transceiver

The Analog Devices MAX3078EESA+ is a 3.3V RS-485/RS-422 transceiver with one driver and one receiver, ±15kV ESD protection, fail-safe operation, and hot-swap capability, housed in an 8-pin SOIC package. It is designed for industrial data links where robust transient protection, low supply voltage, and reduced power consumption are important. An RS-485/RS-422 transceiver is an interface IC that converts between logic-level signals and balanced differential line signals. In the RS-485 mode, the differential bus supports communication between multiple nodes when the system is properly terminated and biased. In RS-422 mode, the device provides a balanced driver and receiver for point-to-point links. The MAX3078EESA+ is part of the broader interface-IC hierarchy and supports both standards in one compact device. Key verified features include ±15kV ESD protection on the bus-facing pins, fail-safe receiver operation that guarantees a logic-high output when receiver inputs are open or shorted, and hot-swap capability designed to eliminate false bus transitions during power-up or hot insertion. The device operates from a 2.97V to 3.63V supply range and contains one driver and one receiver. Manufacturer data describes a supply current of 800µA when unloaded or when fully loaded with the drivers disabled. The MAX3078EESA+ is suitable for industrial controllers, instrumentation links, data acquisition systems, building automation equipment, and embedded communications networks. Its 3.3V supply operation aligns with modern low-voltage digital systems, while the ESD protection and fail-safe circuitry help improve interface reliability in electrically noisy environments. The 8-pin SOIC package supports conventional surface-mount PCB assembly. When laying out a MAX3078EESA+ circuit, keep the bus traces short and controlled, provide the required termination and fail-safe bias network at the appropriate bus locations, and route high-energy transient paths away from sensitive logic. Verify the receiver and driver enable polarity against the system controller because the available control and interface details are not fully specified in the provided verified excerpts. This page combines the verified manufacturer and distributor descriptions with practical RS-485/RS-422 design guidance, package information, selection criteria, and engineering-oriented caveats. Unavailable detailed electrical limits are explicitly marked rather than inferred, allowing designers to validate them against the complete manufacturer datasheet before release to production.

RFC Hubungi kami
MAX307CPI+ - Dual 8:1 CMOS Analog Multiplexer | Maxim
MAX307CPI+

MAX307CPI+ - Dual 8:1 CMOS Analog Multiplexer | Maxim

The Maxim Integrated MAX307CPI+ is a precision, dual 8:1 CMOS analog multiplexer with on-resistance below 100 ohms, channel matching within 5 ohms, and a 28-pin PDIP package. It combines two independently controlled 8:1 muxes, providing 16 analog channels in a single device. The multiplexers support single or dual-polarity operation and are intended for precision signal-routing and instrumentation applications. An analog multiplexer is an interface IC that connects multiple analog inputs to a shared amplifier, converter, or measurement circuit. The MAX307 family occupies the hierarchy of analog switch, analog multiplexer, interface IC, and integrated circuit. By routing signals through matched CMOS switches, it reduces the number of external signal paths while preserving consistent channel resistance across the selected analog range. Key electrical characteristics include less than 100 ohms on-resistance, resistance matching within 5 ohms between channels, and a maximum resistance variation of 7 ohms over the specified analog signal range. The MAX307 is fabricated using Maxim's improved 44 V silicon-gate process. Its monolithic construction supports repeatable switching behavior and low charge injection of less than 10 pC, which helps limit transient errors when a channel changes state. The device provides two 8:1 analog muxes in a 28-pin PDIP package. Pin-compatible MAX307 family members allow commercial and extended-temperature designs to share PCB layouts and mechanical assemblies. Channel matching is particularly important when measuring or converting multiple inputs through one signal chain because differences in resistance otherwise create gain or offset differences between channels. Typical uses include precision data acquisition, automated test equipment, signal characterization, industrial process measurement, and multichannel sensor interfaces. In a data-acquisition circuit, each mux can select a sensor or reference voltage before it reaches a shared amplifier and analog-to-digital converter. The matched resistance reduces channel-to-channel calibration effort, while the 8:1 organization supports compact systems requiring numerous analog inputs. Design the surrounding circuit to keep selected signals within the mux's specified analog range and provide appropriate source and return paths. Because charge injection and off-channel behavior can create transient or crosstalk errors, allow settling time between channel changes and place the mux close to the sensitive amplification stage. The 28-pin PDIP format also requires adequate through-hole clearance and appropriate protection against electrostatic discharge during handling. This product record combines manufacturer family information, commercial listing attributes, package details, selection guidance, and practical PCB considerations. It also distinguishes true pin-compatible MAX307 family members from broader multiplexers that may perform similar routing functions but require a different footprint or interface.

RFC Hubungi kami
MAX307EUI+ - Dual 8:1 100Ω Analog Multiplexer | Analog Devices
MAX307EUI+

MAX307EUI+ - Dual 8:1 100Ω Analog Multiplexer | Analog Devices

The Analog Devices MAX307EUI+ is a precision dual 8:1 CMOS analog multiplexer with less than 100 Ω on-resistance, channel matching within 5 Ω, and switching transitions below 250 ns. The device is packaged in a 28-pin TSSOP and operates from 5 V to 30 V. An analog multiplexer is an integrated switching network that connects one common signal path to multiple input channels. A dual 8:1 configuration provides two independent 8:1 selectors, allowing a precision measurement system to route two signal groups through the same downstream circuitry. Within the power-management hierarchy of semiconductor functions, the MAX307EUI+ belongs to the interface-IC and analog-switch category, where low resistance, low leakage, and predictable channel matching help preserve signal integrity. The MAX307 family uses a monolithic CMOS process identified as an improved 44 V silicon gate process. Its on-resistance is specified below 100 Ω and remains flat over the specified analog signal range, with maximum variation of 7 Ω. Channel-to-channel matching is maintained within 5 Ω, reducing gain errors when different inputs are selected sequentially. Off-state leakage is less than 2.5 nA at +85°C, while transition time is below 250 ns. The MAX307EUI+ is configured as two 8-to-1 analog multiplexers. This arrangement is useful in precision instrumentation, data acquisition, test systems, battery monitoring, and industrial control designs where multiple analog inputs must share a converter or measurement front end. The two selectors can also be used for differential routing when their common terminals and control signals are connected appropriately. System integration requires attention to supply voltage, logic thresholds, signal range, input impedance, and off-channel behavior. Because the control inputs are digital while the switched paths carry analog signals, the device should be positioned close to the sensitive front end to minimize capacitive loading and trace pickup. Decoupling should follow the recommendations in the manufacturer data sheet. For replacement decisions, package body size and pin count alone do not establish compatibility. A suitable drop-in part must also preserve the dual 8:1 topology, pin assignments, control logic, on-resistance behavior, voltage rating, and electrical limits. This page compares the documented MAX307-family alternatives and identifies which differences must be reviewed before changing the BOM. This product documentation combines the manufacturer specifications with application-focused engineering guidance, helping designers evaluate routing performance, switching speed, leakage, package constraints, and practical drop-in replacement options rather than relying on a basic distributor catalog summary.

RFC Hubungi kami
MAX307EWI+ - Dual 8:1 Analog Multiplexer | Analog Devices
MAX307EWI+

MAX307EWI+ - Dual 8:1 Analog Multiplexer | Analog Devices

The Analog Devices MAX307EWI+ is a precision, dual 8:1 CMOS analog multiplexer with low on-resistance below 100 Ω, channel-to-channel matching within 5 Ω, and operation from a 5 V to 30 V analog signal range. It is packaged in a 28-pin WSOIC and provides two independently controlled multiplexers for routing eight analog inputs on each side of the device. An analog multiplexer is an input-selection switch that connects one of several signal inputs to a common output while blocking unselected paths. The MAX307 family belongs to the analog switch and multiplexer hierarchy, where precision low-resistance switching is important when the selected signal must pass with minimal voltage loss, distortion, or injected error. This makes the device suitable for multichannel measurement, data acquisition, instrumentation, and signal-routing systems. Key features include an on-resistance below 100 Ω, matching maintained within 5 Ω between channels, and a maximum change of 7 Ω across the specified analog signal range. Off leakage remains below 2.5 nA at +85°C, while transition time is below 250 ns. These characteristics are particularly valuable when low leakage limits measurement errors and channel matching simplifies calibration of precision analog front ends. The MAX306/MAX307 devices are monolithic CMOS multiplexers built to provide consistent resistance across selected channels. Their low resistance and low leakage reduce signal degradation in measurement paths, while fast switching supports practical acquisition and control cycles. The dual 8-channel organization allows two banks of eight inputs to be routed through one package, reducing component count when a system needs symmetrical or parallel input selection. Typical uses include multiplexed sensor measurement, automated test equipment, battery-cell monitoring, industrial process measurement, programmable instrumentation, and multichannel data-acquisition systems. In each application, the device can reduce the number of analog front-end channels required by selecting inputs sequentially before amplification, filtering, or conversion. Designers should pay close attention to the control logic, input voltage range, signal amplitude, and pin-specific input limits before routing external signals. Keep sensitive analog traces away from switching-control lines, use a stable supply reference, and account for charge injection and off-leakage effects when designing high-impedance measurement systems. This page combines the manufacturer's electrical characteristics with practical routing and measurement guidance, identifies documented same-family drop-in options, and highlights the trade-offs involved when using a dual 8:1 precision multiplexer in an analog signal path.

RFC Hubungi kami
MAX3086EESD+T - 10Mbps RS-485/422 Transceiver, 15kV ESD | ADI
MAX3086EESD+T

MAX3086EESD+T - 10Mbps RS-485/422 Transceiver, 15kV ESD | ADI

The Analog Devices (formerly Maxim Integrated) MAX3086EESD+T is a ±15 kV ESD-protected, fail-safe, 10 Mbps RS-485/RS-422 transceiver with slew-rate-limited driver output, packaged in a 14-pin narrow-body SOIC (NSOIC) and supplied on tape-and-reel. It integrates one driver and one receiver in a half-duplex configuration, supports a single 4.75 V to 5.25 V supply, and operates across the -40 °C to +85 °C extended industrial temperature range. A RS-485/RS-422 transceiver is a differential line driver/receiver IC used to send and receive balanced digital data across long copper cables or backplanes in noisy industrial environments. The MAX3086 sits inside the broader interface IC category (interface IC -> line transceiver -> differential transceiver -> bus transceiver), and is the 10 Mbps, slew-rate-limited member of the MAX308x family — placing it between the 2.5 Mbps MAX3085 and the 115 kbps MAX3082 in the speed ladder. Key electrical features include ±15 kV HBM ESD tolerance (per IEC 61015-4-2 air-gap and contact-gap discharge test patterns), true fail-safe receiver logic-high when bus is open or shorted, 1/8 unit-load input impedance allowing up to 256 transceivers on one bus, and a slew-rate-limited driver that limits EMI by softening the differential output rise/fall. Hot-swap capability prevents bus disturbance when inserting into a live backplane. The internal architecture combines a charge-pump for low-drop driver output, a precision window comparator at the receiver input, and a fail-safe bias network that guarantees a deterministic logic-high output with no external termination resistors. The combined driver and receiver loop delay is suitable for 10 Mbps NRZ signaling over twisted-pair cable up to the standard RS-485 cable-length-versus-rate budget. Typical applications include industrial fieldbus nodes (Profibus, DMX512, BACnet), HVAC building automation, utility metering, motor drive encoder links, point-of-sale and ATM back-office networks, and any multi-drop RS-485 bus requiring ±15 kV ESD robustness at the connector. Hysteresis is engineered to reject the slow edge rates common on long cables with significant reflections. Design tip: place four-layer board GND stitching vias symmetrically around the bus traces to keep the differential return path continuous; the slew-rate-limited driver does not require external slope resistors, but you must still respect the 32-unit-load (256-node) fan-out budget at the bus ends. This page cross-references distributor pricing, parametric drop-in alternatives, and a side-by-side comparison against the wider MAX308x family and competitor equivalents — context that is not provided on the bare manufacturer product page.

RFC Hubungi kami
MAX308EUE+ - 8:1 Low-Resistance CMOS Multiplexer | Analog Devices
MAX308EUE+

MAX308EUE+ - 8:1 Low-Resistance CMOS Multiplexer | Analog Devices

The Analog Devices MAX308EUE+ is a precision 8:1 single-ended CMOS analog multiplexer with on-resistance below 100 ohms, channel matching within 5 ohms, and a variation of no more than 7 ohms across the specified analog signal range. The device is packaged in a 16-pin TSSOP and operates as one 8:1 multiplexer with two 4:1 sections. A single device can therefore route eight analog inputs to a common output while providing complementary select and enable control for embedded measurement or signal-routing systems. An analog multiplexer is a semiconductor switch that connects one of several input terminals to a shared output. The MAX308 belongs to the broader hierarchy of CMOS analog switch, analog multiplexer, signal-routing IC, interface IC, and semiconductor product categories. This distinction matters because multiplexers reduce connector count, simplify instrumentation interfaces, and allow multiple sensors or test points to share a downstream converter without requiring a dedicated amplifier or converter input for every channel. Key characteristics include less than 100 ohms on-resistance, on-resistance matching within 5 ohms between channels, and maximum on-resistance variation of 7 ohms over the specified analog signal range. The matched and flat channel behavior supports predictable gain and attenuation when the selected input changes. Its single-ended 8:1 organization also permits an analog acquisition front end to scan eight sources with only three binary select lines and one enable control, simplifying firmware and reducing the number of external routing components. The MAX308EUE+ uses a precision monolithic CMOS implementation in which the parallel analog paths provide repeatable channel characteristics. Low and tightly matched on-resistance are particularly valuable when downstream circuitry converts the selected signal with limited gain. Because the switch resistance contributes directly to signal attenuation, matching the source and return paths helps limit channel-to-channel error. The low-leakage behavior associated with the CMOS architecture also supports sensitive input arrangements where charge retention and unintended coupling are important. Typical applications include data acquisition, automated test equipment, instrumentation, industrial control, sample-and-hold systems, and battery-powered measurement devices. The multiplexer is particularly suitable when several analog inputs must be measured sequentially by one ADC. It can also divide into two 4:1 paths for applications that need two independently selected analog channels, such as differential sensing, reference routing, or coordinated signal comparison. Design the input and output paths to keep trace resistance and connector resistance small relative to the multiplexer on-resistance. Confirm that every signal remains within the specified analog signal range, and use the manufacturer pin-description table when assigning control inputs and unused terminals. Proper grounding, short return paths, and placement close to the protected analog source help prevent board leakage and routing noise from overwhelming the matched low-resistance benefit.

RFC Hubungi kami
MAX3095CEE+ - ±15kV ESD, 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices
MAX3095CEE+

MAX3095CEE+ - ±15kV ESD, 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3095CEE+ is a quad RS-422/RS-485 receiver delivering up to 10 Mbps data rate with ±15kV IEC-style ESD protection on each input, housed in a 16-pin QSOP (EE) package. It operates from a 3V to 3.6V or 4.75V to 5.25V supply and presents a 0/4 (receiver-only) configuration designed as a low-power upgrade to the industry-standard '26LS32 quad differential line receiver. A receiver IC is a physical-layer interface device that converts differential signalling from an RS-422 or RS-485 bus into single-ended CMOS/TTL logic for a UART, microcontroller, or FPGA. Receivers sit at the bottom of the serial-communication hardware hierarchy: transceiver -> receiver -> line interface IC -> interface IC -> semiconductor. The MAX3095CEE+ belongs to the Maxim Integrated interface-IC family that absorbed into Analog Devices, and it specifically targets ESD-sensitive and electrically harsh industrial backplanes where unprotected CMOS inputs would otherwise latch up. Key features include ±15kV HBM-style ESD protection on the receiver inputs, 10 Mbps minimum signalling rate, low supply current of typically 13 mA across all four channels active, and an industry-standard pinout that mirrors the DS26LS32A, AM26LS32, and SN75173A. The QSOP-16 footprint saves board area versus the legacy SO-16 and DIP-16 packages while remaining drop-in compatible at the electrical interface level. Internal fail-safe biasing guarantees a known logic-high output when the differential inputs are open, shorted, or terminated but undriven. Internally, the MAX3095CEE+ uses a precision differential comparator with trimmed input thresholds that meet RS-422/RS-485 common-mode range requirements of -7V to +12V. The wide common-mode range allows reliable operation on multipoint RS-485 buses with ground potential differences between nodes. Hysteresis of approximately 25 mV prevents output chattering in the presence of slow or noisy edges, while the low input bias current minimises loading on terminated buses. Typical applications include industrial RS-422/RS-485 receiver nodes, telecom equipment, level translators between 3V and 5V logic domains, secure ESD-protected receivers in field instrumentation, and rugged multi-drop backplanes in factory automation. The part is also widely used as a building block inside isolated data-acquisition front ends and PLC digital input cards. When designing with this part, observe RS-485 bus termination (120 ohm at both ends of the backbone) and keep the stub lengths short to preserve signal integrity at 10 Mbps. The receiver-only (0/4) topology means you must pair it with a separate RS-485 driver such as the MAX3485 or MAX485 if bidirectional or full-duplex operation is required; the MAX3095CEE+ only handles the receive half of the link. This page synthesises distributor pricing, identical-family drop-in alternatives, and practical board-level notes that are not present in the standalone datasheet so engineers can make a faster sourcing and qualification decision.

RFC Hubungi kami
MAX3095CEE+T - 10 Mbps Quad RS-422/485 Receiver | Analog Devices
MAX3095CEE+T

MAX3095CEE+T - 10 Mbps Quad RS-422/485 Receiver | Analog Devices

The Analog Devices MAX3095CEE+T is a 10 Mbps quad RS-422/RS-485 receiver with ±15 kV electrostatic-discharge protection, supplied in a 16-pin QSOP package. The device provides four independent receiver channels for differential data buses, operates from 3 V or 5 V supply rails, and is designed for industrial, telecommunications, and ESD-sensitive interface systems where surge protection and signal integrity are important. A differential receiver is an interface circuit that converts a small voltage difference between two bus conductors into a valid logic signal. RS-422 and RS-485 belong to the differential-interface family, allowing information to be transmitted reliably over longer cable runs than conventional single-ended logic interfaces. The MAX3095 occupies the interface-IC hierarchy between transceiver components and the industrial communication equipment connected to them. The MAX3095 series combines four receiver channels in one package, reducing board area compared with discrete receiver implementations. Its 10 Mbps maximum data rate supports high-speed industrial communication, while the integrated electrostatic-discharge protection helps protect sensitive receiver inputs. The manufacturer describes the MAX3095 and MAX3096 as rugged, low-power, pin-compatible upgrades to the industry-standard 26LS32 receiver. Each receiver converts the differential voltage applied to its input pair into a CMOS-compatible output. Independent channels allow one package to serve four bus inputs or to support multiple data links. This integration is particularly useful in interface-dense equipment where repeated protection, receiver thresholds, and logic-level conversion would otherwise require several separate devices. The receiver architecture is suitable for data rates up to 10 Mbps. Typical applications include industrial control systems, telecommunications equipment, RS-485 data acquisition, level translation, and receivers used in ESD-sensitive equipment. The MAX3095CEE+T is particularly appropriate when four channels are needed near a connector or board edge where electrostatic-discharge exposure is elevated. Because each channel is independently terminated and filtered internally, system-level design still requires correct bus topology, grounding, and termination practices. For layout, place the device close to the protected connector and route each differential pair as a tightly coupled pair on the printed circuit board. Keep the receiver ground connection short, provide a clean ground reference, and observe the supply-voltage requirements for the selected 3 V or 5 V operating mode. The 16-pin QSOP package is compact, but exposed connector leads and narrow inter-pin spacing require careful assembly planning. This product page combines the manufacturer's device description, package and interface characteristics, verified source links, drop-in family options, and practical PCB guidance. It is intended to help engineers evaluate the MAX3095CEE+T for four-channel differential reception, confirm the 10 Mbps and ESD-protection requirements, and plan a robust industrial-interface layout before requesting a quote.

RFC Hubungi kami