Produk (44,000+)

MAX232ECD - 5V Dual RS-232 Driver/Receiver | Texas Instruments
MAX232ECD

MAX232ECD - 5V Dual RS-232 Driver/Receiver | Texas Instruments

The Texas Instruments MAX232ECD is a dual RS-232 driver/receiver IC that operates from a single 5V supply and includes integrated IEC61000-4-2 ESD protection on the RS-232 lines. Housed in a 16-pin SOIC (D) package, the device integrates a capacitive voltage-doubler/inverter charge pump that generates the ±10V RS-232 voltage levels from a single 5V rail using four external 1.0 µF capacitors, eliminating the need for a dual-polarity supply. Each part contains two line drivers and two line receivers, supporting full-duplex RS-232 communication at data rates up to 120 kbit/s with ±30V input tolerance on receiver inputs. An RS-232 line driver/receiver (also called a transceiver) is a type of interface IC that bridges the voltage gap between TTL/CMOS logic (0V-5V) and the TIA/EIA-232-F standard (±5V to ±15V swing). It belongs to the broader hierarchy of line drivers -> interface ICs -> integrated circuits -> semiconductors. The MAX232 family is the de-facto industry-standard solution for asynchronous serial-port level translation and is found in nearly every embedded design that needs RS-232 connectivity. Key features include integrated IEC61000-4-2 ESD protection (typically ±15kV air-gap, ±8kV contact discharge on the RS-232 pins), low supply current of typically 8 mA with no load, and 1.0 µF charge-pump capacitors (versus the original MAX232 which used 1.0 µF; the MAX232E and MAX232EC variants retain the same capacitor requirement). The 'C' suffix indicates the commercial 0°C to +70°C operating temperature range. The wide ±30V receiver input range tolerates mis-wired or shorted RS-232 cables without permanent damage. The MAX232ECD uses a charge-pump architecture based on a switched-capacitor voltage doubler and voltage inverter. An internal oscillator (typically 125 kHz) drives the charge pump; the doubled +10V (V+) and inverted -10V (V-) rails feed the driver output stage, while the receiver section operates from the single 5V supply with internal 5 kΩ pull-down resistors. This architecture eliminates the bulky ±12V supplies historically required for RS-232 interfaces. Typical applications include industrial PLC serial ports, point-of-sale (POS) terminals, embedded microcontroller debug consoles, legacy PC COM-port replacements via USB-to-serial bridges, and any design requiring TIA/EIA-232-F compliance. The integrated IEC61000-4-2 ESD protection makes the MAX232ECD especially suitable for cables exposed to user contact or industrial ESD events. When designing with this device, place the four charge-pump capacitors (typically 1.0 µF ceramic) as close to the C1+, C1-, C2+, C2- pins as possible. Although the integrated ESD protection is robust, external TVS diodes are still recommended for the most demanding industrial environments. The MAX232ECD is pin-compatible with the industry-standard MAX232 and may be used as a drop-in upgrade in most existing designs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone - including a parametric comparison versus the MAX3232E, ADM232, and HIN232 families and verified IEC61000-4-2 ESD ratings not always quoted in the datasheet's electrical characteristics table.

RFC Hubungi kami
MAX232ECDR - Dual RS-232 Driver/Receiver, ESD-Protected | TI
MAX232ECDR

MAX232ECDR - Dual RS-232 Driver/Receiver, ESD-Protected | TI

The Texas Instruments MAX232ECDR is a dual RS-232 driver/receiver with integrated IEC 61000-4-2 ESD protection, packaged in a 16-pin SOIC. It operates from a single 5 V supply using 1.0 µF charge-pump capacitors, supplies 2 drivers and 2 receivers, supports data rates to 120 kbit/s, and tolerates ±30 V input levels. The 'E' suffix denotes the enhanced ESD-protected version (HBM ±15 kV, IEC 61000-4-2 contact/air ±8 kV/±15 kV). What is an RS-232 transceiver? An RS-232 transceiver is a type of serial interface IC that translates logic-level (0 V/5 V or 0 V/3.3 V) signals on the TTL/CMOS side to bipolar RS-232 voltage levels (typically ±5 V to ±15 V) required by the TIA/EIA-232-F standard. RS-232 transceivers sit inside the interface ICs family, between UART/SCI controllers and external DB9/DB25 connectors, enabling legacy PC and industrial serial communication. The MAX232 family historically integrated charge-pump doublers/inverters to generate ±10 V from a single +5 V rail, eliminating the need for a dual supply. Key features of the MAX232ECDR include on-chip ±10 V generation from a single 5 V supply via four external 1.0 µF charge-pump capacitors, ±30 V receiver input tolerance that exceeds the TIA/RS-232-F specification, low supply current (typically 8 mA), and TTL/CMOS-compatible logic I/O. The integrated IEC 61000-4-2 ESD protection on the RS-232 lines eliminates external TVS arrays in most designs, reducing BOM cost and PCB area. The device operates across the commercial 0 °C to 70 °C temperature range. The MAX232ECDR uses a CMOS charge-pump voltage doubler/inverter architecture: an internal oscillator drives an external capacitor network that produces V+ (≈ +10 V) and V− (≈ −10 V) rails from the +5 V supply. Drivers translate TTL inputs to RS-232 levels (5 V → +10 V for a mark, 0 V → −10 V for a space); receivers invert and level-shift incoming RS-232 signals back to TTL. The 120 kbit/s data rate supports standard serial links including legacy modems, point-of-sale terminals, and industrial PLC links. Typical applications include factory automation PLCs and industrial control RS-232 ports, point-of-sale (POS) terminals, legacy PC COM ports and peripherals (mice, barcode scanners), embedded microcontroller UART bridges, and instrumentation serial links. The integrated ESD protection makes it especially suitable for handheld and field-exposed equipment where IEC 61000-4-2 air-discharge events are routine. When designing with this part, place the four 1.0 µF charge-pump capacitors as close as possible to the C1+, C1−, C2+, C2− pins to minimize ripple and EMI. Note that VCC must rise monotonically and quickly to ensure proper charge-pump startup; an RC delay on VCC is not recommended. Receiver inputs tolerate ±30 V even when VCC = 0 V (true fail-safe), simplifying hot-plug and powered-down interfaces. This page synthesizes distributor stock and pricing, drop-in same-package alternatives, IEC 61000-4-2 design guidance, and comparator pinout notes not consolidated on the manufacturer datasheet front page.

RFC Hubungi kami
MAX232ECDW - 250kbps RS-232 Transceiver | Texas Instruments
MAX232ECDW

MAX232ECDW - 250kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232ECDW is a dual RS-232 driver and dual receiver interface IC that supports data rates up to 250 kbps from a 4.5V to 5.5V supply. It is housed in a 16-pin SOIC package and includes IEC 61000-4-2 electrostatic-discharge protection. A MAX232 device is a bipolar RS-232 interface transceiver that converts logic-level signals between TTL/CMOS equipment and the positive and negative voltage levels used by RS-232 links. Within the interface IC hierarchy, the MAX232 belongs to the line-driver and line-receiver family, bridging a digital controller or computer port and a physical serial communication cable. The MAX232ECDW integrates two transmit channels and two receive channels, allowing two bidirectional RS-232 ports or one port plus additional point-to-point links to be supported by one device. Its specified operating supply range is 4.5V to 5.5V, and its maximum signaling rate is 250 kbps. IEC 61000-4-2 protection adds electrostatic-discharge resilience to a frequently touched external interface. Internally, the device uses a charge-pump voltage generator to produce the bipolar RS-232 voltage levels required by the drivers while operating from a single low-voltage supply. The receivers convert bipolar RS-232 inputs to TTL and CMOS logic levels, with a typical receiver threshold of 1.3V according to the manufacturer datasheet. Together, the dual-channel arrangement and 250 kbps capability suit control, instrumentation, industrial communication, and legacy computer interfaces. Typical uses include service-console connections, factory equipment interfaces, laboratory instruments, embedded serial bridges, and industrial controllers that retain an RS-232 port. The device is appropriate when a system requires full RS-232 rather than TTL logic levels, particularly for cable connections where voltage polarity, ground reference, and ESD exposure must be considered. A robust layout should place the charge-pump capacitors and supply-decoupling capacitors close to their associated pins, while keeping protected connector-side traces away from sensitive logic. External protection and signal-conditioning components may still be needed when the connected cable is long or the port is exposed to severe industrial transients. This page consolidates the principal electrical characteristics, package details, drop-in replacement candidates, application guidance, and design cautions engineers need when evaluating the MAX232ECDW for an RS-232 interface.

RFC Hubungi kami
MAX232ECDWR - Dual 250kbps RS-232 Transceiver | Texas Instruments
MAX232ECDWR

MAX232ECDWR - Dual 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232ECDWR is a dual RS-232 line driver and receiver with IEC 61000-4-2 electrostatic-discharge protection. It supports a 4.5V to 5.5V supply, operates at up to 250kbps, and is packaged in a 16-pin SOIC. The device includes on-chip charge-pump circuitry for generating the bipolar RS-232 voltage levels required by the transmitters. An RS-232 transceiver is an interface IC that converts between single-ended TTL and CMOS logic levels and the differential, bipolar signaling used by RS-232 equipment. Its transmitters provide level shifting and signal conditioning for outgoing data, while its receivers translate incoming RS-232 signals into logic-compatible levels. The MAX232ECDWR combines two transmitters and two receivers in one package, making it suitable for two-way serial links in industrial control, instrumentation, data acquisition, and legacy peripheral equipment. Key electrical characteristics include operation from a 4.5V to 5.5V single supply and a maximum signaling rate of 250kbps. IEC 61000-4-2 protection is a distinguishing feature for cables and connectors that may be exposed to electrostatic discharge. The 16-pin SOIC package follows the familiar MAX232E pin arrangement, including dedicated charge-pump capacitor pins and a bypass-capacitor connection. These external capacitors must be selected according to the manufacturer datasheet rather than substituted with arbitrary values. The MAX232E architecture uses a capacitive voltage generator to produce the positive and negative voltage levels required for RS-232 transmission. Because this charge-pump architecture needs external capacitors, board layout should keep the charge-pump network compact and place bypass capacitance close to the supply pins. The receiver side converts bipolar RS-232 input levels to CMOS logic levels, allowing the device to interface directly with a host UART or other digital controller. Typical applications include RS-232 ports on industrial test equipment, programmable logic controllers, serial adapters, point-of-sale terminals, laboratory instruments, and embedded control boards. The 250kbps rate is suitable for legacy serial peripherals, configuration links, and short-distance point-to-point communication. The integrated ESD protection is particularly useful where an exposed DB9 or equivalent connector connects the transceiver to external cables. When designing the board, verify the required charge-pump and bypass capacitor values in the manufacturer datasheet and confirm that the 4.5V to 5.5V supply remains within tolerance during transients. Keep protected connector-side routing separated from sensitive logic-side traces, and provide a controlled ground reference between communicating systems to avoid unintended signal offsets. This page combines the exact MAX232ECDWR ordering information, electrical characteristics, cross-reference findings, PCB implementation guidance, and application-specific engineering guidance for engineers evaluating the SOIC-16 transceiver for RS-232 interfaces.

RFC Hubungi kami
MAX232ECDWRE4 - 250kbps Dual RS-232 Transceiver | Texas Instruments
MAX232ECDWRE4

MAX232ECDWRE4 - 250kbps Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232ECDWRE4 is a +5 V dual RS-232 driver and receiver that provides two transmit channels and two receive channels in a 16-pin SOIC package. It supports data rates up to 250 kbps across a 4.5 V to 5.5 V supply range. Its integrated capacitive voltage generator uses four capacitors to produce the bipolar voltage levels required by TIA/EIA-232-F interfaces from a single 5 V supply. An RS-232 transceiver is an interface IC that converts between single-ended TTL/CMOS logic signals and differential, bipolar RS-232 signals. It belongs to the serial-interface hierarchy: RS-232 transceiver → line driver and receiver → interface IC → communication semiconductor. This conversion allows equipment with a logic-level UART to connect to computers, industrial controllers, test equipment, and other RS-232 endpoints through a protected physical interface. The MAX232ECDWRE4 combines two RS-232 drivers, two receivers, and the charge-pump voltage generator in one package. All RS-232 pins feature 15 kV HBM and 15 kV IEC 61000-4-2 air-gap discharge protection, while RS-232 pins also provide 8 kV IEC 61000-4-2 contact-discharge protection. These ratings make the device appropriate for exposed serial ports where electrostatic discharge is a practical concern. The charge-pump architecture creates positive and negative RS-232 levels without a negative supply rail. Its four external charge-pump capacitors determine the required energy-transfer behavior and must be placed close to their associated pins. The receiver converts incoming TIA/EIA-232-F signals into 5 V TTL/CMOS levels, while the drivers convert TTL/CMOS inputs into compliant RS-232 output levels. The MAX232E family is optimized for operation from a single +5 V supply. Typical uses include legacy industrial serial consoles, programmable test equipment, point-of-sale peripherals, data acquisition systems, and service interfaces embedded in larger control systems. The 250 kbps maximum data rate supports moderate-speed asynchronous links rather than high-bandwidth differential serial protocols. Full-duplex operation allows a port to transmit and receive simultaneously through independent channels. PCB design should prioritize short traces from the charge-pump capacitors to pins 1 and 4, as specified by the Texas Instruments MAX232E datasheet. Keep the interface connector and transceiver pins away from sensitive analog or high-speed digital nodes, and route the ground return with the RS-232 signal path to reduce noise pickup. A common-mode choke can be added when cable emissions or susceptibility become significant. This page combines the manufacturer interface specifications, protection ratings, package details, verified sourcing information, drop-in alternatives, and practical layout guidance in one engineering-focused reference for evaluating the MAX232ECDWRE4 in +5 V RS-232 designs.

RFC Hubungi kami
MAX232ECDWRG4 - Dual RS-232 Interface | Texas Instruments
MAX232ECDWRG4

MAX232ECDWRG4 - Dual RS-232 Interface | Texas Instruments

Texas Instruments MAX232ECDWRG4 is a dual RS-232 driver and receiver interface IC with two transmit channels, two receive channels, and IEC 61000-4-2 protection. It operates from a single 5 V supply, supports data rates to 120 kbit/s, accepts input levels to ±30 V, and uses 1.0 uF charge-pump capacitors. The device is packaged in a 16-pin SOIC. An RS-232 transceiver is an interface circuit that converts logic-level UART signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. Within the interface hierarchy, the MAX232 belongs to the RS-232 transceiver family, which combines drivers, receivers, charge-pump voltage conversion, and transient protection in one semiconductor package. The MAX232ECDWRG4 includes two drivers and two receivers, allowing one package to support two RS-232 communication channels. Its single 5 V supply architecture simplifies system power planning, while the integrated charge pump generates the positive and negative voltages required by RS-232 drivers. Operation up to 120 kbit/s makes the device appropriate for legacy serial ports, industrial control links, equipment interfaces, and embedded systems using compatible RS-232 protocols. IEC 61000-4-2 protection is a key feature for connectors exposed to electrostatic discharge. The protection capability helps reduce system susceptibility to ESD events at the interface boundary, although it does not eliminate the need for correct grounding, cable design, and connector placement. The input circuitry tolerates levels to ±30 V, supporting the voltage stress commonly encountered on RS-232 networks. Typical uses include PC-compatible serial ports, test equipment, security systems, instrumentation, industrial controllers, and point-of-sale equipment. Two complete driver-receiver sections can also support separate transmit and receive paths or more than one RS-232 port when several devices share the same PCB. The 16-pin SOIC package supports conventional surface-mount assembly and is easy to route on standard industrial-control boards. Place the two 1.0 uF charge-pump capacitors close to their designated pins, connect the supply and ground pins to low-impedance planes, and route the RS-232 traces away from sensitive analog signals. Confirm that the external capacitor voltage rating and dielectric are suitable for the charge-pump waveform. PCB power and ground handling should account for the charge pump's switching current even though the interface itself is designed for a single 5 V rail. This product overview combines the verified electrical capabilities, package details, interface standards, application guidance, replacement considerations, and practical layout notes needed to evaluate the MAX232ECDWRG4 for an RS-232 design. It also highlights the distinction between direct pin-compatible replacements and broader functional alternatives when maintaining an existing circuit board.

RFC Hubungi kami
MAX232ECNG4 - Dual RS-232 Transceiver | Texas Instruments
MAX232ECNG4

MAX232ECNG4 - Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232ECNG4 is a dual RS-232 transceiver with one driver and one receiver per channel, integrated ESD protection, and a 16-pin plastic dual in-line package measuring 0.300 inch by 0.300 inch with a 7.62 mm body width. It is designed for systems that require bidirectional RS-232 conversion between modern digital logic and older serial interfaces. An RS-232 transceiver is an interface IC that translates low-voltage CMOS or TTL-compatible logic levels to and from the higher-voltage bipolar signaling used by RS-232. A complete interface path commonly includes a transceiver for the main serial connection, a driver for additional lines, and a receiver for incoming data. The MAX232ECNG4 belongs to the RS-232 interface level within the broader semiconductor and interface IC hierarchy. The principal feature of the MAX232ECNG4 is its integrated 2-transceiver arrangement. One channel can transmit while the other receives, allowing full-duplex communication with only two device channels. Integrated ESD protection is particularly useful at exposed connector pins, where static discharge from cables and connected equipment can damage a communications interface. The through-hole 16-pin package also supports conventional PCB assembly and connector-routing layouts. This device is associated with the MAX232 product family from Maxim, which was acquired by Analog Devices and is now offered through Texas Instruments. The ECNG4 ordering code identifies the specific commercial-temperature, 16-pin plastic DIP configuration. Exact electrical ratings, driver and receiver thresholds, charge-pump performance, supply limits, and environmental classifications must be confirmed in the manufacturer datasheet before the circuit is released for production. Typical uses include industrial control consoles, data-acquisition equipment, test systems, service interfaces, and embedded serial ports. The MAX232ECNG4 can also pair with dedicated RS-232 line drivers or receivers when a system requires more than two channels or an RS-485-to-RS-232 conversion stage. Connection to a modern host generally requires a logic-level UART, while the opposite side connects to an RS-232 connector and its external signal ground. The principal design consideration is ensuring the transceiver operates with valid logic levels and supply voltage throughout startup, data transmission, and cable disconnection. Decoupling capacitors, cable routing, signal-ground handling, and ESD exposure all affect reliability. Confirm the required charge-pump capacitor values, driver slew behavior, receiver thresholds, and maximum data rate in the manufacturer datasheet before finalizing the layout. This product record combines interface identification, package information, application guidance, comparison criteria, and practical design notes. It also distinguishes verified drop-in alternatives by package, temperature grade, and functional fit so engineers can narrow replacements without treating every similar RS-232 transceiver as an automatic substitution.

RFC Hubungi kami
MAX232ECPE+ - 120kbps 5V RS-232 Transceiver | Analog Devices
MAX232ECPE+

MAX232ECPE+ - 120kbps 5V RS-232 Transceiver | Analog Devices

The Analog Devices MAX232ECPE+ is a dual RS-232 transceiver with one driver and one receiver per channel, operates from a single 4.5V to 5.5V supply, supports data rates through 120kbps, and is packaged in a 16-pin PDIP. Designed for EIA/TIA-232E and CCITT V.28 links, it provides the electrical conversion required between TTL/CMOS logic and balanced RS-232 signals. The integrated charge-pump circuitry generates the required RS-232 voltage levels without a separate negative power supply. An RS-232 transceiver is an interface IC that bridges a digital logic system and a serial communications port. RS-232 uses single-ended, bipolar signaling in which logic levels are represented by positive and negative voltages relative to ground. Within the electronics hierarchy, the MAX232ECPE+ is an interface IC, an RS-232 transceiver, a line driver and receiver pair, and ultimately a semiconductor communication component. It is commonly placed between a UART, microprocessor, controller, or service connector and an external RS-232 port. Key verified features include two transmit channels and two receive channels, operation from one 4.5V to 5.5V supply, and support for data rates up to 120kbps. Distributor and manufacturer-family sources identify the MAX232E line as meeting EIA/TIA-232E and CCITT V.28 requirements when loaded. The device also offers 15kV ESD protection according to distributor descriptions, improving interface robustness against electrostatic discharge encountered during cable connection or industrial use. The MAX232ECPE+ uses integrated charge-pump circuitry to generate the positive and negative voltage levels needed by RS-232 drivers from the single low-voltage supply. Receivers convert the incoming bipolar RS-232 signal into a digital level compatible with the connected logic system. Exact pin names, electrical limits, propagation timing, and capacitor values should be confirmed in the manufacturer data sheet before layout because those details were not included in the supplied verified excerpts. Typical applications include legacy RS-232 service consoles, instrumentation, point-of-sale equipment, industrial controllers, and adapter boards that connect TTL/CMOS UART devices to DB9 or other RS-232 connectors. The 120kbps capability is suitable for moderate-speed serial links, while the 5V supply simplifies integration with established digital systems. For new designs, the MAX233 family may be attractive when eliminating external charge-pump capacitors is more important than retaining the MAX232E footprint and feature set. When designing the interface, connect the charge-pump capacitors and supply bypassing capacitors exactly as specified by the manufacturer. Keep the RS-232 connector-side nets away from sensitive analog and high-speed digital traces, and provide the connector ground as a short, robust return path. ESD protection helps, but it does not replace correct signal routing, chassis grounding, or system-level surge protection. This page combines verified manufacturer and distributor references, cross-reference results, packaging information, application guidance, and design cautions to support faster component selection. It deliberately distinguishes verified electrical facts from values that require confirmation from the complete data sheet, helping engineers avoid treating incomplete search snippets as a substitute for the manufacturer specification.

RFC Hubungi kami
MAX232ECPWRG4 - Dual RS-232 Transceiver | Texas Instruments
MAX232ECPWRG4

MAX232ECPWRG4 - Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232ECPWRG4 is a dual RS-232 line-driver and receiver IC with IEC 61000-4-2 electrostatic-discharge protection. The device provides two transmit channels and two receive channels, operates from a single 5 V power supply, supports data rates up to 120 kbit/s, and accepts receiver input levels of ±30 V. It is packaged in a 16-pin TSSOP measuring 4.40 mm in body width. An RS-232 transceiver is an interface IC that bridges a digital logic system and a serial port using the voltage levels defined by the RS-232 standard. The MAX232 belongs to the hierarchy of interface ICs, serial interface transceivers, line drivers and receivers, and semiconductor components. It is useful when a controller, test instrument, industrial controller, or other digital system must communicate with an RS-232 port through a compact, low-power interface. The MAX232ECPWRG4 includes two RS-232 drivers and two receivers in one package. According to the manufacturer datasheet, it operates from one 5 V supply, uses 1.0 µF charge-pump capacitors, and operates to 120 kbit/s. These characteristics make it suitable for legacy serial-port equipment, control systems, instrumentation, and point-of-sale equipment where RS-232 compatibility is required. Its internal charge-pump circuitry generates the bipolar voltage levels required to drive RS-232 signals from a single low-voltage supply. The transmitter and receiver sections provide level translation in both directions, allowing a UART-compatible logic side to connect to a ±30 V-capable RS-232 side. The specified operating speed supports conventional serial links without requiring a high-speed differential interface. The device also includes IEC 61000-4-2 ESD protection, a distinguishing feature for systems in which a connected cable can expose the interface to electrostatic discharge. Appropriate external protection, grounding, routing, and enclosure design remain necessary because the IC alone does not eliminate every system-level ESD hazard. Shielded or twisted-pair cable practices should be considered for longer or electrically noisy interconnects. Because the MAX232ECPWRG4 is obsolete and no longer manufactured, engineers should plan a lifecycle review before starting a new production design. Existing equipment can use the part for repair or controlled redesign work, but new designs should compare active alternatives carefully for package, pinout, logic levels, charge-pump capacitance, data rate, and supply requirements. A candidate should not be treated as drop-in solely because it is described as a MAX232-family device. This product page summarizes the device function, documented operating characteristics, package, lifecycle status, sourcing route, and engineering considerations. It also separates the obsolete target from similarly named MAX232 variants whose packages or protection options differ, helping buyers assess replacements without assuming that a different suffix is a direct substitute.

RFC Hubungi kami
MAX232ECSE+ - 2/2 RS-232 Transceiver, 15kV ESD | Analog Devices
MAX232ECSE+

MAX232ECSE+ - 2/2 RS-232 Transceiver, 15kV ESD | Analog Devices

The Analog Devices MAX232ECSE+ is a dual RS-232 line transceiver that combines two drivers and two receivers in a 16-pin SOIC package. It operates from a single +5 V supply, supports data rates up to 120 kbps, and integrates a charge pump for the RS-232 bipolar voltage levels required by V.28 communications. The MAX232ECSE+ also provides high ±15 kV human-body-model ESD protection on its interface pins. It is designed for industrial-control equipment, data acquisition systems, service interfaces, and other equipment that must translate between RS-232 and TTL/CMOS logic levels. The MAX232ECSE+ is a 16-SOIC surface-mount device offered in an extended-temperature option, making it suitable for applications where commercial-temperature transceivers are not appropriate. Its integrated charge pump eliminates the external ±10 V supply normally required by RS-232 equipment, while the on-chip level translation removes the need for external RS-232 line drivers and receivers. Electrical characteristics including propagation delay, receiver threshold, driver output levels, supply current, and temperature limits should be confirmed against the manufacturer datasheet before release to production. For a new design that requires an additional RS-232 channel, the MAX3232E family provides four drivers and four receivers while retaining a comparable 16-pin SOIC footprint. Conversely, the MAX232ECSE+ is the simpler choice for point-to-point links that need only one full-duplex RS-232 port. Its defined driver and receiver count also makes the pin assignment straightforward, although unused receiver inputs must be properly biased rather than left floating. This page also organizes drop-in alternatives, application-specific guidance, package and brand comparisons, and practical PCB design notes for engineers evaluating the MAX232ECSE+ in industrial serial-port designs.

RFC Hubungi kami
MAX232ECSE+T - 120kbps 5V RS-232 Transceiver | Analog Devices
MAX232ECSE+T

MAX232ECSE+T - 120kbps 5V RS-232 Transceiver | Analog Devices

The Analog Devices MAX232ECSE+T is a dual-driver, dual-receiver RS-232 transceiver operating from a single 5V supply at data rates up to 120kbps, with ±15kV ESD protection and a 16-pin narrow SOIC package. It integrates the charge-pump circuitry required to generate RS-232-compatible bipolar levels from one low-voltage supply. The device provides two transmit channels and two receive channels, making it suitable for compact point-to-point serial interfaces. An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and a RS-232 port. Within the electronics hierarchy, it belongs to interface ICs, where its role is to bridge a low-voltage digital system and a differential, bipolar communications bus. Unlike a direct TTL or CMOS serial connection, the MAX232ECSE+T adds level translation and electrical protection at the connector-facing side of a design. The principal features include dual RS-232 drivers, dual receivers, operation from a single 5V supply, and a maximum signaling rate of 120kbps. The integrated charge pump supplies the positive and negative voltage levels expected by RS-232 receivers. According to the Analog Devices MAX232 datasheet, Rev. 18, the device is designed to meet EIA/TIA-232E and CCITT V.28 interface requirements when operated under the specified loading conditions. The MAX232ECSE+T also incorporates ±15kV human-body-model ESD protection on its interface pins. This protection improves tolerance to electrostatic discharge encountered during connector installation, servicing, or nearby industrial activity. It does not replace a complete surge-protection strategy, but it provides a useful first line of defense around a serial interface. The device uses a 16-SOIC surface-mount package intended for compact industrial, instrumentation, and embedded-control assemblies. Typical uses include RS-232 adapters for embedded systems, programming and service ports for industrial equipment, point-to-point links between microcontrollers and peripheral boards, control interfaces for laboratory instruments, and communication ports in building-control equipment. A second transmitter and receiver can support a single-ended two-way RS-232 link when the application requires one path in each direction. When laying out the circuit, place the charge-pump capacitors close to their designated pins and route the connector-side driver and receiver nets away from sensitive analog or high-speed digital traces. Verify the host-side logic levels, cable length, grounding strategy, and external protection before enabling the interface. Avoid assuming that the integrated ESD rating permits unprotected exposure to severe industrial surge events. This page combines the manufacturer's interface specifications, practical PCB guidance, package-level replacement analysis, and application-focused comparisons to support faster component selection. It also distinguishes electrical, protection, and packaging trade-offs that are not obvious from the RS-232 transceiver category label alone.

RFC Hubungi kami
MAX232ECWE+ - 120kbps RS-232 Transceiver | Maxim
MAX232ECWE+

MAX232ECWE+ - 120kbps RS-232 Transceiver | Maxim

The Maxim Integrated MAX232ECWE+ is a dual RS-232 transceiver with two drivers and two receivers, a 120 kbps data rate, ±15 kV ESD protection, and a single 4.5 V to 5.5 V supply requirement. It is packaged in a 16-pin SOIC and uses an integrated charge pump to generate RS-232 bipolar voltage levels from a 5 V supply. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts received RS-232 signals back into CMOS or TTL-compatible logic. The MAX232 belongs to the RS-232 transceiver hierarchy, which includes multi-channel transceivers and line-driver and receiver ICs used to connect older serial equipment to modern digital systems. The device provides two transmit channels and two receive channels in a single package, allowing one RS-232 port to support two directions of data transfer. Its 120 kbps maximum data rate suits conventional asynchronous serial links, while the integrated charge pump removes the need for external ±12 V power. The ±15 kV ESD protection helps improve robustness on cables and connector interfaces exposed to electrostatic discharge. Operation from a 4.5 V to 5.5 V supply allows use with conventional 5 V digital systems. The transmitter converts CMOS/TTL inputs into RS-232-compatible output levels, while the receivers use threshold and hysteresis to interpret bipolar RS-232 inputs as logic signals. The MAX232E family is specifically designed for RS-232 and V.28 communications, including industrial and instrumentation environments where signal conditioning and interface protection are important. Typical applications include service-port interfaces, industrial control systems, test and measurement equipment, POS terminals, and embedded systems that need to communicate with legacy RS-232 peripherals. Two driver and two receiver channels also permit two complete RS-232 links when each link requires one transmit and one receive direction. PCB design should preserve the manufacturer's recommended charge-pump capacitor network and place the associated capacitors close to their designated pins. Keep the interface connector and unprotected logic-side traces separated as far as practical, and route any externally accessible cable shield or ground connection according to the enclosure and system grounding architecture. This page combines package, interface, purchasing, and replacement information with practical guidance for implementing a robust 5 V RS-232 link. It also identifies genuine pin-compatible options and highlights the temperature-range, lifecycle, and protection considerations that determine whether an alternative can serve as a true drop-in replacement.

RFC Hubungi kami
MAX232ECWE+T - 5V RS-232 Transceiver, 120kbps | Analog Devices
MAX232ECWE+T

MAX232ECWE+T - 5V RS-232 Transceiver, 120kbps | Analog Devices

The Analog Devices MAX232ECWE+T is a dual RS-232 transceiver with two drivers and two receivers, 120kbps data-rate capability, ±15kV ESD protection, and a 16-pin SOIC package. It operates from a single +5V supply and integrates charge-pump circuitry to generate the positive and negative voltages required by RS-232 line drivers. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 differential voltage levels and converts incoming RS-232 signals back into logic-compatible levels. It belongs to the interface IC hierarchy, where transceivers connect modern digital systems to older, noise-tolerant serial ports. The MAX232ECWE+T is intended for EIA/TIA-232E and CCITT V.28 communication links operating from a single 5V rail. The integrated charge pump eliminates the need for a separate negative supply, allowing the MAX232ECWE+T to operate from 4.5V to 5.5V. Its two transmit channels provide full-duplex serial communication, while two receive channels support simultaneous bidirectional data exchange. The ±15kV human-body-model ESD protection improves tolerance when users, cables, or external equipment connect to the communication port. As a CMOS interface device, the MAX232ECWE+T combines low-power 5V operation with level translation between TTL-compatible circuitry and RS-232. Internal transmitter and receiver functions implement the voltage conversion required at the physical interface, while the charge-pump section supports the bipolar signal levels used by compliant RS-232 equipment. The 16-pin SOIC package supports conventional surface-mount assembly and standard board-level inspection. Typical uses include industrial equipment serial ports, laboratory instrumentation, point-of-sale terminals, embedded control systems, and service-console connections. The device is especially useful where the host electronics have a 5V supply and the connected peripheral expects a physical RS-232 port rather than USB or a low-voltage differential interface. Cable protection and grounding remain important when connecting the transceiver to long or electrically noisy external cables. For a new design, place the required charge-pump capacitors close to their associated pins and route each driver output directly toward its connector. Keep logic-side traces away from RS-232 line outputs, provide a solid ground return, and select external protection appropriate to the cable environment. Review the device's operating-temperature grade and absolute-maximum limits before using it outside a commercial-temperature enclosure. This page combines the verified MAX232ECWE+T interface specifications, same-package cross-reference options, application guidance, and a parameter comparison that helps engineers distinguish electrical, package, and grade differences before approving a substitution.

RFC Hubungi kami
MAX232ECWE+TG104 - Dual RS-232 IC | Analog Devices
MAX232ECWE+TG104

MAX232ECWE+TG104 - Dual RS-232 IC | Analog Devices

Analog Devices MAX232ECWE+TG104 is a dual RS-232 transceiver IC with one transmitter and one receiver, operated from a single 4.5 V to 5.5 V supply in a 16-pin SOIC package. The device provides integrated charge-pump circuitry, eliminating the need for a bipolar positive and negative supply, and includes integrated protection rated at ±15 kV HBM ESD. An RS-232 transceiver is an interface integrated circuit that converts logic-level signals into RS-232-compatible levels and converts received RS-232 signals back into logic levels. It belongs to the line-driver and line-receiver hierarchy within interface ICs. This device is intended for bidirectional serial communication over cables or other RS-232 links where the host supplies a single positive supply voltage. The principal features of the MAX232ECWE+TG104 are its dual 2/2 transceiver arrangement, 4.5 V to 5.5 V supply range, integrated charge-pump capability, and integrated ±15 kV human-body-model ESD protection. The 16-pin gull-wing SOIC package supports conventional surface-mount assembly and provides enough pins for the receiver, transmitter, supply, ground, and externally connected charge-pump capacitors. The MAX232 family uses CMOS-compatible logic on the digital interface side while the integrated charge-pump circuitry creates the bipolar voltage levels required by RS-232. This arrangement simplifies system power design because the circuit does not require separate positive and negative supplies. ESD protection integrated into the interface can improve resistance to electrostatic discharge encountered during handling or connection of external cabling. Typical uses include industrial control equipment, data-acquisition systems, serial adapters, service-console interfaces, and legacy peripheral connections. In each case, the transmitter converts outgoing logic signals into RS-232 levels, while the receiver translates incoming levels into logic signals understood by the host controller. The commercial temperature grade identifies this ordering code as intended for normal commercial operating conditions. Designers should place the required external capacitors close to the charge-pump pins and route the RS-232 interface traces away from sensitive digital signals. Ground-return continuity and compliant cable practices remain important because integrated ESD protection does not eliminate the need for good enclosure and grounding practices. Confirm the complete pin assignment, absolute maximum ratings, and capacitor values against the manufacturer datasheet before layout release. This product page combines the device identification, verified technical characteristics, sourcing guidance, and application-focused design information. It also identifies genuinely comparable package and ordering variants while making clear where a complete pin-level alternative cannot be established without additional manufacturer cross-reference information.

RFC Hubungi kami
MAX232EESE+ - 120kbps RS-232 Transceiver | Analog Devices
MAX232EESE+

MAX232EESE+ - 120kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX232EESE+ is a dual RS-232 line-driver and receiver transceiver operating from a single +5 V supply, with integrated charge-pump circuitry and 15 kV ESD protection. It supports data rates up to 120 kbps and is packaged in a 16-pin narrow SOIC for surface-mount industrial equipment, data acquisition systems, and RS-232 communication ports. An RS-232 transceiver is an interface IC that converts logic-level signals into bipolar RS-232 levels and converts incoming RS-232 signals back into logic levels. Within the interface hierarchy, MAX232EESE+ belongs to the RS-232 transceiver family of communication interface ICs. It is intended for EIA/TIA-232E and CCITT V.28 links where the endpoint equipment supplies low-voltage logic while the cable interface requires approximately positive and negative voltage signaling. The MAX232EESE+ provides two transmit channels and two receive channels in one package. Its integrated voltage-generation circuitry lets the device operate from one +5 V rail without a separate negative supply. The manufacturer states that the MAX232E family meets EIA/TIA-232E and CCITT V.28 specifications at data rates up to 120 kbps when loaded. The MAX232E suffix also identifies the 15 kV ESD-protected version listed for the product. The 16-pin narrow SOIC package supports compact, surface-mounted implementations and automated assembly. Because RS-232 is a single-ended, unbalanced interface, the transceiver simplifies the physical layer but does not provide galvanic isolation, common-mode rejection comparable to differential buses, or long-distance protection beyond the specifications of the MAX232E family. Circuit design should account for connector protection, cable transients, ground continuity, and unused driver or receiver inputs. Typical uses include serial adapters, test and measurement instruments, programmable logic controllers, industrial control panels, and embedded equipment that previously relied on a legacy RS-232 port. A microcontroller can connect to the logic-side inputs and outputs, while the line-side pins connect through the DB9 or other RS-232 connector. When laying out a design, place the device close to the connector and place its required charge-pump capacitors on the shortest practical signal paths. Keep the RS-232 traces away from clocks, switching regulators, and sensitive analog inputs. External protection may still be needed for severe industrial environments even though the device includes 15 kV ESD protection. This page combines the manufacturer's MAX232E family information with interface-focused engineering guidance, package details, purchasing questions, and a practical evaluation of replacement options. It helps engineers determine whether the MAX232EESE+ fits an existing 16-pin SOIC RS-232 design before requesting a quote.

RFC Hubungi kami
MAX232EESE+T - 120kbps ESD RS-232 Transceiver | Analog Devices
MAX232EESE+T

MAX232EESE+T - 120kbps ESD RS-232 Transceiver | Analog Devices

Analog Devices MAX232EESE+T is a +5 V RS-232 line-driver and receiver transceiver with two drivers, two receivers, full-duplex operation, data rates up to 120 kbps, and ±15 kV ESD protection in a 16-pin SOIC package. It uses an integrated charge pump to generate the bipolar voltage levels required by RS-232 from a single 5 V supply. An RS-232 transceiver is an interface IC that converts between digital logic signals and the voltage-defined, unbalanced signaling used by RS-232 equipment. The MAX232E belongs to the line-driver and receiver hierarchy, combines two signal channels in one package, and is designed for EIA/TIA-232E and CCITT V.28 communication links where ±12 V is unavailable. Key features include two transmit channels, two receive channels, full-duplex RS-232 operation, and operation at data rates up to 120 kbps. The integrated charge pump eliminates the need for an external ±12 V supply, while ±15 kV human-body-model ESD protection improves robustness on connectors and cables that may be exposed to electrostatic discharge. The E-suffix device is supplied in a 16-pin SOIC package for surface-mount assembly. Internally, the transmit drivers use the charge-pump-generated rails to produce RS-232-compatible output levels from TTL or CMOS-compatible inputs. The receive channels detect RS-232 logic levels and translate them into logic-compatible signals for the host or controller. Because the device supports both directions in one package, it is suitable for point-to-point links requiring simultaneous transmission and reception, subject to the signaling and grounding requirements of the connected equipment. Typical applications include industrial serial ports, data-acquisition equipment, instrumentation, barcode and identification systems, and embedded control systems using legacy RS-232 equipment. The device is particularly useful where a modern controller must communicate with an RS-232 printer, test instrument, modem, or service interface while retaining protection at the externally accessible connector. Designers should follow the manufacturer’s recommended charge-pump capacitor and logic-side bypass-capacitor recommendations. Keep the protected connector-side traces away from sensitive logic, provide a low-impedance ground path between communicating systems, and verify that the selected transceiver, wiring, and enclosure address the required ESD and isolation strategy for the installation. This page combines the MAX232EESE+T interface specifications, package and lifecycle information, qualified drop-in alternatives, and practical RS-232 design guidance. It also distinguishes exact drop-in choices from functional alternatives so engineers can assess footprint, speed, protection, and qualification before approving a replacement.

RFC Hubungi kami
MAX232EEWE+ 120kbps RS-232 Transceiver | Analog Devices
MAX232EEWE+

MAX232EEWE+ 120kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX232EEWE+ is a dual driver and dual receiver RS-232 transceiver designed for +5 V operation, with one transmitter and one receiver channel. It supports data rates up to 120 kbps and is packaged in a 16-pin wide SOIC. The MAX232EEWE+ also includes an on-chip charge-pump voltage generator for converting the single +5 V supply into the bipolar voltage levels required by RS-232 drivers. An RS-232 transceiver is an interface IC that connects logic-level equipment to a serial port using the EIA/TIA-232E electrical standard. Each receiver translates a bipolar RS-232 signal into a TTL or CMOS logic level, while each driver converts a logic-level signal into the bipolar voltage required at the RS-232 port. This interface belongs to the broader hierarchy of transceiver IC, interface IC, and communication semiconductor. The MAX232EEWE+ meets EIA/TIA-232E and CCITT V.28 specifications according to the Analog Devices product page. Its two-driver, two-receiver arrangement supports equipment with two serial channels while keeping the external interface compact. Operation from a single +5 V supply simplifies system design because the charge pump generates the required positive and negative transmitter voltages internally. The wide SOIC package is also available in a 16-pin surface-mount form. At the circuit level, the device combines two RS-232 drivers, two RS-232 receivers, and a charge-pump voltage converter. The charge-pump section requires external storage capacitors, allowing the transmitter section to generate the positive and negative rail voltages needed for compliant RS-232 output levels. Receiver inputs accept bipolar RS-232 signals and produce digital logic outputs suitable for the host controller or peripheral. Typical uses include industrial serial adapters, data-acquisition equipment, instrument-control panels, embedded serial ports, and communication links between a logic board and a legacy RS-232 peripheral. The 120 kbps operating capability supports moderate-speed point-to-point links, while the dual-channel organization can serve two ports or provide transmit and receive paths for more than one interface. PCB layout is critical because charge-pump capacitors must be connected close to their designated pins, and RS-232 driver outputs should be routed away from sensitive receiver and logic traces. Protection networks may be added at exposed connectors, but they must not distort signal timing or prevent the driver from meeting its specified output levels. This page combines the device architecture, verified operating specifications, package details, application guidance, and form-fit-function alternatives to support faster design review and sourcing. It also distinguishes true pin-compatible alternatives from functional equivalents that require circuit or package changes.

RFC Hubungi kami
MAX232EEWE+T - 120kbps RS-232 Transceiver | Analog Devices
MAX232EEWE+T

MAX232EEWE+T - 120kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX232EEWE+T is a dual-driver, dual-receiver RS-232 transceiver operating from a single 5V supply, with data rates up to 120kbps and ±15kV HBM ESD protection. The device is housed in a 16-pin wide SOIC package and is supplied in tape-and-reel packaging. Its integrated charge-pump circuitry produces the bipolar voltage levels required by RS-232 interfaces from one 5V supply, reducing the external component count compared with discrete driver designs. An RS-232 transceiver is a bidirectional interface IC that converts between single-ended logic-level signals and the bipolar signaling used by RS-232 equipment. Within the interface hierarchy, the MAX232E belongs to the RS-232 transceiver family, which is part of transceiver ICs, interface ICs, and broader semiconductor components. Two driver channels convert outgoing logic signals, while two receiver channels convert incoming RS-232 signals into CMOS-compatible levels. This makes the device suitable for equipment with two serial ports or for a single port requiring bidirectional communication. The MAX232E family provides two transmitters and two receivers, supports operation at up to 120kbps, and meets EIA/TIA-232E and CCITT V.28 interface specifications according to the Analog Devices product page. Its integrated charge-pump circuitry permits single-supply operation, while ±15kV human-body-model ESD protection helps improve robustness at connector-facing pins. The wide 16-SOIC package is also available in common industrial assembly and inspection workflows. Each channel uses the electrical behavior expected of a standard MAX232-family RS-232 interface. The charge pump develops the positive and negative voltages needed by the drivers, allowing the receiver side to recognize valid RS-232 levels while rejecting signals outside the specified transition region. Four active channels in one package reduce board area compared with separate single-channel transceiver packages. The device therefore balances functional integration, standard interface compatibility, and a widely supported package format. Typical uses include industrial serial adapters, instrumentation links, point-of-sale equipment, data-acquisition systems, and control panels that connect a TTL or CMOS controller to an RS-232 port. It can also support legacy equipment migrations where the host interface still uses RS-232 and the new controller requires logic-level serial signaling. The 120kbps maximum data rate accommodates many legacy peripheral and instrumentation protocols without requiring a higher-bandwidth physical-layer transceiver. Designers should preserve the charge-pump capacitor arrangement and place the required capacitors close to the appropriate device pins. RS-232 cable transients and ESD events occur at the connector, so the ground reference, cable routing, and interface protection arrangement also matter. Confirm the logic polarity, receiver threshold behavior, and shutdown state before substituting this device into a design with mixed RS-232 families. This product page combines the manufacturer interface specifications, package details, verified cross-reference context, selection guidance, and practical application notes to support a faster engineering decision. It also highlights where same-package alternatives can be evaluated without changing the PCB footprint.

RFC Hubungi kami
MAX232EID - 120kbps RS-232 Transceiver | Texas Instruments
MAX232EID

MAX232EID - 120kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232EID is a dual RS-232 line driver and receiver with a single 5 V supply, data rates up to 120 kbit/s, and enhanced electrostatic-discharge protection. It is housed in a 16-pin SOIC package and provides two transmit channels and two receive channels for bidirectional serial interfaces. An RS-232 transceiver is an interface IC that translates logic-level signals between a host or controller and a noisy, long-distance serial link. The MAX232EID uses a capacitive voltage generator to produce the positive and negative voltages required by TIA/EIA-232-F and ITU V.28 interfaces. This places it within the RS-232 transceiver, interface IC, and broader semiconductor hierarchy. Key features include operation from one 5 V supply, support for 1.0 µF charge-pump capacitors, a maximum data rate of 120 kbit/s, and receiver input levels extending to ±30 V. According to the Texas Instruments MAX232E product information, all RS-232 pins provide 15 kV human-body-model protection, 15 kV IEC61000-4-2 air-gap discharge protection, and 8 kV IEC61000-4-2 contact-discharge protection. The MAX232EID combines two drivers and two receivers with the internal charge-pump circuitry required to generate bipolar RS-232 voltage levels from a 5 V supply. Its receivers convert incoming RS-232 signals to 5 V TTL or CMOS levels, while its drivers convert TTL or CMOS logic into TIA/EIA-232-F-compatible output levels. This integration simplifies legacy serial-port and industrial-control designs. Typical applications include RS-232 ports on embedded systems, industrial controllers, test equipment, data-acquisition systems, and legacy computer peripherals. The 120 kbit/s operating rate supports many point-to-point serial links, while the enhanced ESD ratings are useful where a cable or connector can expose the interface to electrostatic discharge. Use the pin-description and typical-application information in the manufacturer datasheet when assigning connector and protection components. Confirm the external charge-pump capacitor values, supply decoupling, logic-level compatibility, and connector-side protection against the operating environment before releasing a PCB layout. This page combines the manufacturer specifications with practical interface guidance, package details, and verified drop-in comparison information. It helps engineers assess the MAX232EID for legacy RS-232 connectivity, identify compatible alternatives, and plan ESD-aware PCB implementation without changing the core transceiver architecture.

RFC Hubungi kami
MAX232EIDR - 120kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX232EIDR

MAX232EIDR - 120kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX232EIDR is a dual RS-232 line driver and receiver with a single 5 V supply, data rates up to 120 kbit/s, and enhanced electrostatic-discharge protection. It is housed in a 16-pin SOIC package and provides two transmit channels and two receive channels for bidirectional serial interfaces. An RS-232 transceiver is an interface IC that translates logic-level signals between a host or controller and a noisy, long-distance serial link. The MAX232EIDR uses a capacitive voltage generator to produce the positive and negative voltages required by TIA/EIA-232-F and ITU V.28 interfaces. This places it within the RS-232 transceiver, interface IC, and broader semiconductor hierarchy. Key features include operation from one 5 V supply, support for 1.0 µF charge-pump capacitors, a maximum data rate of 120 kbit/s, and receiver input levels extending to ±30 V. According to the Texas Instruments MAX232E product information, all RS-232 pins provide 15 kV human-body-model protection, 15 kV IEC61000-4-2 air-gap discharge protection, and 8 kV IEC61000-4-2 contact-discharge protection. The MAX232EIDR combines two drivers and two receivers with the internal charge-pump circuitry required to generate bipolar RS-232 voltage levels from a 5 V supply. Its receivers convert incoming RS-232 signals to 5 V TTL or CMOS levels, while its drivers convert TTL or CMOS logic into TIA/EIA-232-F-compatible output levels. This integration simplifies legacy serial-port and industrial-control designs. Typical applications include RS-232 ports on embedded systems, industrial controllers, test equipment, data-acquisition systems, and legacy computer peripherals. The 120 kbit/s operating rate supports many point-to-point serial links, while the enhanced ESD ratings are useful where a cable or connector can expose the interface to electrostatic discharge. Use the pin-description and typical-application information in the manufacturer datasheet when assigning connector and protection components. Confirm the external charge-pump capacitor values, supply decoupling, logic-level compatibility, and connector-side protection against the operating environment before releasing a PCB layout. This page combines the manufacturer specifications with practical interface guidance, package details, and verified drop-in comparison information. It helps engineers assess the MAX232EIDR for legacy RS-232 connectivity, identify compatible alternatives, and plan ESD-aware PCB implementation without changing the core transceiver architecture.

RFC Hubungi kami
MAX232EIDW - 250kbps RS-232 Transceiver | Texas Instruments
MAX232EIDW

MAX232EIDW - 250kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232EIDW is a dual-channel RS-232 line driver/receiver with a 250 kbps data rate, 5 V supply, and ±9 V driver output levels in a 16-pin SOIC (DW) package. It adds ±15 kV IEC 61000-4-2 ESD protection to the established MAX232 dual-driver, dual-receiver architecture. A RS-232 transceiver is an interface IC that converts logic-level signals between TTL/CMOS equipment and balanced, bipolar RS-232 lines. Within the interface hierarchy, the MAX232E belongs to the line-driver/receiver family, implements the RS-232 physical-layer interface, and supports communication between equipment that uses different voltage domains. Its integrated charge-pump circuitry generates the required positive and negative voltage from one 5 V supply. The device provides two transmit channels and two receive channels for full-duplex serial links. According to the Texas Instruments MAX232 datasheet, each receiver accepts inputs up to ±30 V, uses a typical threshold of 1.3 V, and has typical hysteresis of 0.5 V. The enhanced MAX232E variant supports 250 kbps operation and ±15 kV IEC-ESD protection, making it suitable for industrial control, instrumentation, and equipment interfaces exposed to electrostatic discharge. Internally, the charge-pump voltage generator produces the bipolar voltages required by RS-232 drivers while onboard capacitors provide the required charge-pump operation. The MAX232EIDW is specified for operation from −40 °C to +85 °C and uses the DW 16-pin SOIC package. Receiver inputs can withstand bipolar voltages up to ±30 V, while the drivers supply approximately ±9 V output levels for compliant RS-232 signaling. Typical uses include industrial serial consoles, programmable test equipment, data-acquisition systems, point-of-sale terminals, and embedded controllers communicating with legacy RS-232 peripherals. The ±15 kV ESD rating is especially useful where a connector cable can expose the interface to electrostatic discharge, although system-level protection and grounding remain necessary for long or outdoor cables. When laying out the circuit, place the charge-pump capacitors close to their associated pins and keep the RS-232 traces away from sensitive analog and high-speed digital paths. Provide a solid ground-plane connection and use appropriate cable transient protection when the interface leaves an enclosure. This page combines manufacturer specifications, replacement guidance, application engineering notes, and same-package comparisons for faster component selection and PCB planning.

RFC Hubungi kami
MAX232EIDWG4 - Dual RS-232 Transceiver | Texas Instruments
MAX232EIDWG4

MAX232EIDWG4 - Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX232EIDWG4 is a dual RS-232 line-driver and receiver transceiver with two transmit channels, two receive channels, and IEC 61000-4-2 electrostatic-discharge protection. It operates from a single 5 V supply in a 16-pin SOIC package, with an industrial temperature range of -40°C to +85°C. The MAX232EIDWG4 is intended for systems that require bidirectional RS-232 communication over longer distances than TTL logic can support reliably. An RS-232 transceiver is an interface IC that converts between single-ended TTL/CMOS logic and differential, bipolar RS-232 signals. Its line drivers convert outgoing logic levels into RS-232 levels, while its receivers convert incoming RS-232 signals into logic-compatible levels. The MAX232 family integrates the required charge-pump circuitry, drivers, and receivers, allowing a printed circuit board to implement two complete RS-232 channels without discrete level-shifting circuits. The principal feature of the MAX232EIDWG4 is its dual-channel architecture, which provides two drivers and two receivers in one 16-pin SOIC package. Integrated IEC 61000-4-2 protection improves interface robustness in industrial environments where cables and connector signals may be exposed to electrostatic discharge. Its -40°C to +85°C operating range supports both commercial and industrial equipment, while the SOIC package supports conventional surface-mount assembly and automated inspection. The device includes on-chip charge-pump circuitry for RS-232 signal generation, reducing the external component count compared with discrete driver designs. Charge-pump capacitors and supply bypass capacitors must be placed close to their associated pins to maintain stable operation. The SOIC footprint also requires consideration of lead pitch, board-edge clearance, and thermal performance when the transceiver is mounted near a power supply or in a densely routed enclosure. Typical applications include industrial serial controllers, laboratory instruments, data acquisition equipment, configuration ports, and service interfaces. It is especially useful when a legacy RS-232 port must coexist with a modern controller operating at TTL logic levels. Two channels can also support separate transmit and receive paths, full-duplex communication, or multiple interfaces sharing one package. For a new layout, follow the manufacturer datasheet pin-description table and recommended capacitor network exactly. Check the selected driver and receiver connections against the required RS-232 direction, grounding arrangement, and cable-side protection strategy. PCB creepage, isolation spacing, and exposed connector placement should be evaluated even when the IC itself includes ESD protection. This page organizes the MAX232EIDWG4 specifications, verified sourcing links, structured alternatives, application guidance, and design checks into one engineering-focused reference. It helps distinguish package, temperature-range, protection, and channel-count considerations before committing the part to an RS-232 interface design.

RFC Hubungi kami
MAX232EIDWR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX232EIDWR

MAX232EIDWR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)

Texas Instruments MAX232EIDWR is a dual-channel RS-232 line driver/receiver with a 250 kbps data rate, 5 V supply, and ±9 V driver output levels in a 16-pin SOIC (DW) package. It adds ±15 kV IEC 61000-4-2 ESD protection to the established MAX232 dual-driver, dual-receiver architecture. A RS-232 transceiver is an interface IC that converts logic-level signals between TTL/CMOS equipment and balanced, bipolar RS-232 lines. Within the interface hierarchy, the MAX232E belongs to the line-driver/receiver family, implements the RS-232 physical-layer interface, and supports communication between equipment that uses different voltage domains. Its integrated charge-pump circuitry generates the required positive and negative voltage from one 5 V supply. The device provides two transmit channels and two receive channels for full-duplex serial links. According to the Texas Instruments MAX232 datasheet, each receiver accepts inputs up to ±30 V, uses a typical threshold of 1.3 V, and has typical hysteresis of 0.5 V. The enhanced MAX232E variant supports 250 kbps operation and ±15 kV IEC-ESD protection, making it suitable for industrial control, instrumentation, and equipment interfaces exposed to electrostatic discharge. Internally, the charge-pump voltage generator produces the bipolar voltages required by RS-232 drivers while onboard capacitors provide the required charge-pump operation. The MAX232EIDWR is specified for operation from −40 °C to +85 °C and uses the DW 16-pin SOIC package. Receiver inputs can withstand bipolar voltages up to ±30 V, while the drivers supply approximately ±9 V output levels for compliant RS-232 signaling. Typical uses include industrial serial consoles, programmable test equipment, data-acquisition systems, point-of-sale terminals, and embedded controllers communicating with legacy RS-232 peripherals. The ±15 kV ESD rating is especially useful where a connector cable can expose the interface to electrostatic discharge, although system-level protection and grounding remain necessary for long or outdoor cables. When laying out the circuit, place the charge-pump capacitors close to their associated pins and keep the RS-232 traces away from sensitive analog and high-speed digital paths. Provide a solid ground-plane connection and use appropriate cable transient protection when the interface leaves an enclosure. This page combines manufacturer specifications, replacement guidance, application engineering notes, and same-package comparisons for faster component selection and PCB planning.

RFC Hubungi kami
MAX232EIN - 5V RS-232 Transceiver | Texas Instruments | DIP-16
MAX232EIN

MAX232EIN - 5V RS-232 Transceiver | Texas Instruments | DIP-16

The Texas Instruments MAX232EIN is a dual RS-232 driver and dual receiver interface IC with a 4.5 V to 5.5 V single supply, 250 kbps data rate, and IEC 61000-4-2 protection, housed in a 16-pin PDIP package. It provides two transmit channels and two receive channels for converting TTL/CMOS logic levels to RS-232 voltage levels and back again. A transceiver combines the functions of an RS-232 line driver and line receiver in one integrated circuit. In the broader semiconductor hierarchy, the MAX232EIN belongs to the interface IC class, where communication between systems with different voltage levels is handled by level-shifting and signal-conditioning devices. Its integrated charge-pump voltage generator allows the device to produce the positive and negative RS-232 voltages required by the standard from a single 5 V supply. The MAX232EIN is designed for 250 kbps data rates and uses on-chip protection against electrostatic discharge. Its integrated protection is identified in the product description as IEC 61000-4-2 protection, making it useful for industrial equipment, communications equipment, and other systems where an RS-232 connector may be exposed to user-contact transients. The 16-pin PDIP package is suitable for through-hole PCB layouts and hand-assembled prototypes. The device is used when a controller, terminal, printer, instrument, or another embedded system must communicate through an RS-232 port. Each receiver converts an RS-232 input to a logic-compatible signal, while each driver converts a logic input into an RS-232 output. The internal charge-pump circuit supplies the bipolar voltage levels required by the RS-232 interface without a separate negative power supply. For robust board implementation, place the charge-pump capacitors close to their associated pins and route the transmit and receive traces away from sensitive analog or high-speed digital signals. Decoupling capacitors should be located near the supply pins, and the external connector should include the required RS-232 signal-ground reference. The MAX232EIN is most appropriate when a single 5 V supply, a compact dual-channel interface, and a legacy RS-232 connection are required. This page combines the manufacturer device description with package information, drop-in comparison options, application guidance, and design notes for engineers selecting or replacing the MAX232EIN. The listed alternatives are limited to verified same-package choices; no cross-package RS-232 devices are presented as drop-in replacements.

RFC Hubungi kami