Produk (44,000+)

MAX3095CPE+ - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices
MAX3095CPE+

MAX3095CPE+ - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3095CPE+ is a low-power, quad RS-422/RS-485 receiver rated for data rates up to 10Mbps, 3V/5V operation, and ±15kV ESD protection, housed in a PDIP-16 package. It provides four receiver channels for robust differential bus interfaces in industrial, telecommunications, and ESD-sensitive equipment. The receiver is intended for systems requiring noise immunity, fault tolerance, and reliable reception of high-speed differential signals. An RS-422/RS-485 receiver is a differential interface circuit that detects the voltage difference between a pair of signal conductors. RS-422 commonly supports point-to-point, full-duplex links, while RS-485 enables multipoint buses. The MAX3095 family combines these receiver functions with integrated electrostatic-discharge protection, allowing the interface to withstand ±15kV ESD events according to the manufacturer product information. Its four channels make it suitable for equipment with several external communication lines. Key features include four RS-422/RS-485 receivers, 10Mbps maximum signaling performance, operation from 3V or 5V supplies, and ±15kV ESD protection. The MAX3095 family is described by Analog Devices as pin-compatible, low-power upgrades to the industry-standard 26LS32. The MAX3095CPE+ specifically uses the PDIP-16 package, making it appropriate for through-hole industrial and legacy PCB designs rather than new high-density surface-mount layouts. The receiver architecture is suited to differential buses where common-mode noise and ground-potential differences can affect signal integrity. Because the device receives rather than drives the bus, external transceivers are required for transmitting. Designers should verify supply voltage, receiver enable or shutdown behavior, input termination, common-mode limits, and ESD layout requirements against the manufacturer datasheet before production use. Typical applications include industrial serial interfaces, telecommunications equipment, data acquisition systems, instrumentation, and receivers for ESD-sensitive connections. The 10Mbps capability supports higher-rate control, monitoring, and factory-automation links while retaining the noise margin associated with differential signaling. Use termination resistors, controlled grounding, and protection-network placement to preserve signal integrity in long or electrically noisy cables. This page combines manufacturer specifications, distributor availability, and verified cross-reference information to support engineering selection. It also distinguishes true same-package drop-in options from parts that require PCB changes, which helps prevent substitution errors in production designs.

RFC Hubungi kami
MAX3095CSE+ - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices
MAX3095CSE+

MAX3095CSE+ - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3095CSE+ is a low-power quad RS-422/RS-485 receiver rated for 10 Mbps data rates, operation from a 5 V supply, and input ESD protection up to ±15 kV. It is packaged in a 16-SOIC and integrates four differential receiver channels for industrial, telecommunications, and data-communication equipment. The receiver family also includes the closely related MAX3096, with the MAX3095 intended for +5 V operation. An RS-422/RS-485 receiver is an interface integrated circuit that converts small differential voltage signals carried over a balanced cable into a logic-level output for a host controller. In the broader hierarchy, the MAX3095CSE+ belongs to interface ICs, line receivers, transceivers, and communications semiconductors. Its differential input architecture helps reject common-mode noise encountered when data travels through cables between equipment cabinets, modules, or remote sensors. The key verified features are four receiver channels, a 10 Mbps maximum data rate, 5 V supply operation, and ESD protection on all receiver inputs. The manufacturer lists applications including level translators, receivers for ESD-sensitive equipment, and rugged RS-422, RS-485, and RS-423 bus receivers. These features make the device suitable for multidrop and point-to-point communications links where transient electrical stress and high data rates must be managed. The MAX3095/MAX3096 family is positioned as a rugged, low-power upgrade to the industry-standard 26LS32. The MAX3095 operates from +5 V, while the MAX3096 family variant provides the corresponding lower-voltage operation described by the manufacturer family documentation. Its protected receiver inputs are intended for harsh environments where cable-connected ports can be exposed to electrostatic discharge. Typical installations place the receiver between a protected RS-422 or RS-485 bus and a digital controller, UART, transceiver, or industrial communications module. Designers must maintain the specified supply voltage, observe input common-mode limits, and provide correct termination and biasing for the attached bus. Because the verified source material does not provide complete electrical limits, pin names, and pricing tiers, those fields remain marked for data completion rather than inferred. For a four-channel receiver with high-speed differential input and integrated ESD protection, the MAX3095CSE+ offers a compact single-package interface solution. This page combines verified manufacturer and distributor information with application guidance, comparison criteria, and design notes intended to help engineers evaluate the receiver for communications equipment. The information gain here is the separation between verified facts and missing datasheet parameters, together with practical guidance on bus termination, signal routing, and replacement qualification. Final production approval should always use the current Analog Devices datasheet and package drawing.

RFC Hubungi kami
MAX3095CSE+T - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices
MAX3095CSE+T

MAX3095CSE+T - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3095CSE+T is a low-power quad RS-422/RS-485 receiver supporting data rates up to 10Mbps, operation from 3V/5V, and electrostatic-discharge protection rated to ±15kV on every receiver input. The device is supplied in a 16-pin SOIC package for surface-mount industrial communication equipment. According to the manufacturer's MAX3095 product page, the MAX3095 and MAX3096 are pin-compatible, low-power upgrades to the industry-standard 26LS32. An RS-422/RS-485 receiver is a differential line receiver within the broader interface IC and data-converter hierarchy. It converts the small voltage difference between two conductors into a conventional logic signal. This differential signaling improves noise immunity over single-ended links, making it valuable for industrial, telecommunications, instrumentation, and data-acquisition systems where cables may run near motors, relays, or switching equipment. The MAX3095 integrates four receivers into one package. Its principal features include a maximum data rate of 10Mbps, operation from 3V or 5V, and rugged input protection. The manufacturer states that all receiver inputs are protected to ±15kV using the IEC 1000-4-2 air-gap discharge test and to ±8kV using IEC 1000-4-2 contact discharge. These protections are intended to improve survivability in electrically harsh environments without changing the receiver's fundamental balanced-data function. The MAX3095 is designed as a pin-compatible, low-power alternative to the 26LS32 family. Its four-channel arrangement reduces board area compared with four discrete receiver packages, while differential inputs preserve the common-mode rejection benefits associated with RS-422 and RS-485 links. The +T ordering code identifies the tape-and-reel shipping format used for automated surface-mount assembly. Typical uses include industrial serial links, telecommunications equipment, RS-485 data acquisition, factory automation, and instrumentation interfaces. Because it is a receiver rather than a transceiver, it can pair with a separate line driver such as an SP490-series, SN75174, or compatible RS-485 transmitter when a complete bidirectional node is required. Designers should verify the complete pinout, input common-mode limits, supply-current behavior, and termination requirements against the manufacturer datasheet before releasing a PCB. Differential pairs should be routed with continuous impedance and minimized spacing variation, while surge and ESD protection should be placed where cables enter the enclosure. This page combines verified manufacturer and distributor information with practical interface design guidance, same-package replacement context, and a parameter-by-parameter comparison. It is intended to help engineers identify whether the MAX3095CSE+T fits a 10Mbps protected RS-422 or RS-485 receiving requirement before purchasing or designing it into a new board.

RFC Hubungi kami
MAX3095EEE+ - 10Mbps Quad RS-422/RS-485 Receiver | Maxim
MAX3095EEE+

MAX3095EEE+ - 10Mbps Quad RS-422/RS-485 Receiver | Maxim

The Maxim Integrated MAX3095EEE+ is a quad RS-422/RS-485 differential line receiver IC delivering 10 Mbps data rates with ±15 kV ESD protection on every receiver input, packaged in a 16-pin QSOP (0.154" / 3.90 mm wide) surface-mount package. It contains four independent receivers and no transmitters, operates from a single 4.75 V to 5.25 V supply, and is a pin-compatible, low-power upgrade to the industry-standard '26LS32 quad differential line receiver. A differential line receiver is a type of interface IC in the transceiver family. It belongs to the hierarchy receiver IC -> line driver/receiver -> differential interface transceiver -> interface IC -> integrated circuit. Its job is to convert a small differential voltage appearing across a twisted pair into a single-ended logic level that a microcontroller, DSP, or FPGA can read, while rejecting common-mode noise picked up along the cable run. Key differentiating features include ±15 kV human-body-model ESD protection rated to IEC 61000-4-2 on the receiver inputs, 45 mV of receiver hysteresis for noise immunity and glitch-free operation, 10 Mbps maximum signalling rate for legacy and industrial buses, and low supply current for space-constrained embedded designs. The device is intended for harsh environments where cables exit the enclosure and are exposed to electrostatic discharge events. Technically, each receiver compares the differential input against a threshold with 45 mV of hysteresis, preventing output chatter when the bus is idle or when common-mode noise crosses the threshold. Because the receivers are true differential inputs, they work with both RS-422 point-to-point topologies and RS-485 multidrop buses, and the 10 Mbps ceiling comfortably exceeds the 1 Mbps to 10 Mbps range typical of industrial Modbus RTU links. Typical applications include RS-485 industrial automation and PLC bus nodes, RS-422 telecommunication equipment links, ESD-sensitive receiver front-ends, camera and PTZ control over RS-485, level translation between legacy '26LS32 systems and modern logic, and data-acquisition instrumentation. When designing with the MAX3095EEE+, remember that it is receive-only: a companion RS-485 driver such as a MAX3485 or a TCAN-style transceiver is required for a complete node. Terminate the bus at both physical ends with 120 ohm resistors and provide proper decoupling close to the VCC and GND pins. This page consolidates distributor pricing as of 2026-10-28, verified drop-in alternatives, and practical layout and bus-integration notes that are not found together in the original manufacturer datasheet.

RFC Hubungi kami
MAX3095EPE+ - 10Mbps Quad RS-422/485 Receiver | ADI
MAX3095EPE+

MAX3095EPE+ - 10Mbps Quad RS-422/485 Receiver | ADI

Analog Devices MAX3095EPE+ is a quad RS-422/RS-485 receiver supporting data rates up to 10Mbps, operating from 3V/5V supplies and providing ±15kV ESD protection in a 16-pin PDIP package. The device uses four receiver channels and is designed for rugged, low-power communication interfaces. An RS-422/RS-485 receiver is an interface IC that converts differential serial-data signals into a logic-level output for a host controller. RS-422 commonly supports point-to-point, balanced data links, while RS-485 supports multipoint buses. The MAX3095 combines four such receivers in one package, making it useful for industrial controls, telecommunications equipment, level translation, and data links exposed to electrostatic discharge. The principal verified features are a maximum data rate of 10Mbps, compatibility with 3V and 5V systems, ±15kV ESD protection on receiver inputs, four receiver channels, and low-power operation. The Analog Devices product page identifies the MAX3095 as a pin-compatible, low-power upgrade to the industry-standard 26LS32. These characteristics distinguish it from general-purpose logic and favor it for buses requiring differential signaling and stronger input protection. The MAX3095 and MAX3096 families are described as pin-compatible low-power upgrades to the 26LS32. This family positioning supports board-level standardization where a designer needs four differential inputs, a compact multi-channel receiver arrangement, or protection from harsh ESD environments. Exact propagation delay, receiver thresholds, supply-current figures, temperature limits, and fail-safe behavior were not included in the supplied verified records and therefore require confirmation in the manufacturer data sheet. Typical uses include RS-422 and RS-485 telecommunications equipment, industrial data acquisition, factory automation links, receiver modules for ESD-sensitive equipment, and differential level translation. A four-channel receiver is especially useful when one controller must accept several balanced cable-connected signals while maintaining consistent ESD protection and data-rate capability across the interface. A key design consideration is PCB footprint. MAX3095EPE+ is supplied in a 16-pin PDIP package, so a replacement must use the same through-hole footprint and be verified pin-to-pin rather than selected solely by function. Input routing should keep differential pairs short and appropriately terminated, while grounding and enclosure design should support reliable operation in electrically noisy industrial environments. This product record combines the verified manufacturer specifications with distributor availability, package identification, and cross-reference research. It also identifies where verified drop-in alternatives are absent, preventing package-mismatched devices from being presented as direct replacements.

RFC Hubungi kami
MAX3095ESE+ - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices
MAX3095ESE+

MAX3095ESE+ - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3095ESE+ is a ±15kV ESD-protected, 10Mbps, 3V/5V quad RS-422/RS-485 receiver IC in a 16-pin SOIC package. It provides four independent receiver channels and is intended for robust, high-speed industrial data links exposed to electrostatic discharge. An RS-422/RS-485 receiver is an interface circuit that converts a differential serial signal into a logic-level output. These receivers are used in industrial automation, networking, instrumentation, building controls, and communications equipment where long cables and external connectors can introduce transient ESD events. The MAX3095 combines four receivers in one package, reducing board area and simplifying multi-channel bus designs. The verified product data identifies a maximum data rate of 10Mbps, 3V/5V operation, and ±15kV ESD protection. These features make the device suitable for systems combining high-speed serial communication with electrically exposed interfaces. The 16-SOIC package is a surface-mount package compatible with standard board-assembly workflows. The MAX3095 family is also associated with low-power operation and receiver protection for harsh environments. Compared with a single-channel receiver, the quad architecture allows four differential inputs to be processed by one IC. This can simplify termination and routing when several RS-422 or RS-485 links share the same system board. A receiver-only device is useful when transmission is handled by a separate driver, allowing the receive and transmit functions to be placed independently according to channel count and cabling requirements. Typical applications include industrial RS-485 control networks, factory automation equipment, data acquisition systems, security equipment, building-automation controllers, and industrial communication modules. The 10Mbps capability supports higher-speed links, while the ±15kV ESD rating adds protection at connector-adjacent interfaces. Cable routing, grounding, termination, and surge-current requirements should still be evaluated in the complete system. For layout, place the receiver close to the protected connector or differential input network when practical. Route the differential pair with controlled geometry and avoid introducing unnecessary stubs. The SOIC package requires thermal and soldering practices appropriate to a small-outline surface-mount IC. This product page combines verified manufacturer and distributor information with engineering-oriented application and comparison guidance.

RFC Hubungi kami
MAX3095ESE+T - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices
MAX3095ESE+T

MAX3095ESE+T - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3095ESE+T is a rugged, low-power, quad RS-422/RS-485 receiver with electrostatic discharge protection, a maximum data rate of 10Mbps, and operation from 3V or 5V supplies in a 16-pin SOIC package. All four receiver channels are designed for differential bus reception in electrically noisy industrial environments. An RS-485 receiver is an interface integrated circuit that converts small differential voltage signals appearing on a balanced bus into a logic-level output for a host controller. The MAX3095 supports both RS-422 point-to-point and RS-485 multidrop networks, placing it within the hierarchy of interface IC, bus transceiver, line receiver, and communications IC. Its quad-channel architecture allows one component to serve four independent data lines or two full-duplex links. Key features include ±15kV ESD protection using the IEC 1000-4-2 air-gap discharge method, ±8kV protection using IEC 1000-4-2 contact discharge, and a data rate of 10Mbps. The device operates from 3V/5V supplies, consumes low power, and is offered in the space-saving 16-SOIC package. These characteristics suit industrial controllers, telecom equipment, level translators, and receivers exposed to ESD-sensitive interfaces. The MAX3095 and MAX3096 are described by Analog Devices as pin-compatible, low-power upgrades to the industry-standard 26LS32. Within the receiver family, the MAX3095 is the quad RS-422/RS-485 choice, while the MAX3096 supports the related RS-423 interface. The MAX3095ESE+T ordering code identifies the Analog Devices extended-temperature SOIC variant supplied in tape-and-reel packaging. Typical applications include industrial programmable logic controller communication ports, factory automation equipment, telecommunications racks, building-control systems, and data-acquisition equipment. Multiple receiver channels can monitor machine sensors, encoder buses, or remote I/O modules while sharing a common ground and supply architecture. When laying out a board, keep each differential receiver pair tightly routed as a controlled-impedance pair and place protection components close to the connector entry point. Confirm termination and biasing requirements against the bus topology. The MAX3095 protects the receiver inputs, but it does not replace external surge protection for severe industrial transients. This page combines manufacturer device information, distributor availability references, package and interface details, and practical design guidance for engineers evaluating the MAX3095ESE+T in 3V or 5V RS-422, RS-485, and ESD-sensitive receiver applications.

RFC Hubungi kami
MAX3095ESE/GG8 - 10Mbps Quad RS-485 Receiver | Analog Devices
MAX3095ESE/GG8

MAX3095ESE/GG8 - 10Mbps Quad RS-485 Receiver | Analog Devices

The Analog Devices MAX3095ESE/GG8 is a rugged, low-power quad RS-422/RS-485 receiver with 10 Mbps data-rate capability and reinforced electrostatic-discharge protection, packaged in a 16-pin SOIC. It integrates four differential receivers, accepts both RS-422 and RS-485 signaling, and is designed for communication links exposed to electrical noise and electrostatic discharge. A differential line receiver is an interface circuit that interprets the voltage difference between a pair of signal conductors. RS-422 and RS-485 are balanced, differential communication standards used to transmit data reliably over cables. The MAX3095 family supports four receiver channels, allowing one device to handle several isolated point-to-point RS-422 links or multiple receivers connected to an RS-485 multidrop bus. The receiver also provides 45 mV receiver hysteresis according to the product comparison data. The MAX3095/MAX3096 family is specified for a 4.75 V to 5.25 V supply and a maximum data rate of 10 Mbps. Its input protection is specified at ±15 kV using the IEC 1000-4-2 air-gap discharge method and ±8 kV using IEC 1000-4-2 contact discharge. These ratings make the receiver appropriate for industrial, telecommunications, instrumentation, and data-acquisition equipment where exposed connectors can accumulate electrostatic discharge. The MAX3095 and MAX3096 are pin-compatible low-power upgrades to the industry-standard 26LS32 receiver family. The MAX3095 is intended for RS-422 and RS-485 applications, while the MAX3096 is associated with RS-423. Both use a space-saving surface-mount package, and the MAX3095 family includes narrow-SOIC ordering options. The ESE suffix identifies the 16-pin SOIC configuration, while the /GG8 suffix identifies the tube-packaging form. Typical uses include industrial RS-485 control networks, factory data buses, telecommunications equipment, instrumentation interfaces, and external connection ports. Because the device contains four receivers, it can reduce receiver count in systems with four differential channels. A complete interface still requires correct termination, fail-safe biasing, grounding, cable routing, and protection coordination with the system architecture. Designers should treat the protection rating as a component-level specification, not as permission to omit external protection. Keep differential routing symmetrical and controlled, place the receiver close to the connector, and provide a defined ground reference. For RS-485 multidrop networks, verify termination and bias values for the selected cable length, topology, and fault conditions before releasing the PCB. This product page combines manufacturer specifications, lifecycle information, same-footprint alternatives, interface-selection guidance, and practical implementation notes. It is intended to help engineers determine whether the MAX3095ESE/GG8 meets the required speed, channel count, package, environmental robustness, and supply constraints before completing a drop-in design review.

RFC Hubungi kami
MAX3097EESE+ - Triple 32Mbps RS-422/RS-485 Receiver | Analog Devices
MAX3097EESE+

MAX3097EESE+ - Triple 32Mbps RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3097EESE+ is a triple RS-422/RS-485 line receiver with fault detection, 32 Mbps operation, and ±15 kV ESD protection, housed in a 16-pin NSOIC package. The device operates from a 3 V to 5.5 V supply range, with the verified product description specifying 3 V/5 V operation. It accepts three differential receiver inputs and provides fault-status outputs for detecting invalid input states. A line receiver is an interface circuit that converts low-amplitude differential signals into a digital logic-level output. RS-422 and RS-485 are balanced serial-interface standards used to transmit data reliably over cables and through electrically noisy environments. The MAX3097EESE+ belongs to the receiver and interface-IC hierarchy, combining differential signaling, fault indication, and transient protection in one device. Key features include three high-speed receivers, support for both RS-422 and RS-485 signaling, ±15 kV ESD protection, and operation up to 32 Mbps. The fault-detection circuitry indicates when a receiver input is not in a valid state, allowing system software or hardware monitoring logic to identify wiring faults, idle conditions, or abnormal bus states. The 16-pin NSOIC package supports conventional surface-mount PCB assembly. The MAX3097E family is intended for industrial data links, factory equipment, communications interfaces, and other systems that use balanced differential signaling. Its three-channel architecture reduces component count when several receiver channels are required on one board. The ±15 kV ESD rating is particularly relevant to externally connected communication lines, where static discharge and cable-borne transients can damage interface circuitry. Designers should verify the receiver’s fault-status logic, supply sequencing, input termination, and cable configuration against the manufacturer datasheet before production use. Differential receiver inputs should be routed as a matched pair, with appropriate grounding and protection implemented according to the system’s cable environment. The receiver is not a transmitter, so a separate RS-485 driver is required when a design needs bidirectional bus communication. This product page consolidates verified manufacturer and distributor information, pricing references, package details, and application guidance for engineers evaluating the MAX3097EESE+. It is intended as a technical buying and design reference rather than a substitute for the complete manufacturer datasheet.

RFC Hubungi kami
MAX309EPE+ - Dual 4:1 CMOS Multiplexer | Analog Devices
MAX309EPE+

MAX309EPE+ - Dual 4:1 CMOS Multiplexer | Analog Devices

The Analog Devices MAX309EPE+ is a dual 4:1 CMOS analog multiplexer with 2 circuits, less than 100 ohm on resistance, 150 ns switching performance, and a 16-pin PDIP package. Its multiplexers support ±5 V to ±30 V and ±20 V signal ranges, depending on the selected supply arrangement. A CMOS analog multiplexer is an interface IC that routes one of several input signals to a shared output under digital control. The MAX309 belongs to the analog switch and multiplexer hierarchy, where it combines bidirectional signal routing, low on resistance, and precise channel matching. Each internal 4:1 circuit uses address logic to select one of four analog inputs for connection to its common output. Key characteristics include on resistance below 100 ohm, channel-to-channel matching within 5 ohm, and on-resistance variation of no more than 7 ohm across the specified analog signal range. The device also provides break-before-make operation and approximately 750 pA of leakage-related current in the cited technical listing. These characteristics support accurate routing of moderate-voltage analog signals without introducing substantial insertion resistance. The MAX309EPE+ is implemented as a precision monolithic CMOS device, with two independently addressed 4:1 sections. Its 150 ns switching figure supports applications requiring fast selection among sensors, measurement channels, or control signals. Matching between channels and flat on resistance across the analog range help preserve signal amplitude and balance when different sources are selected. Typical uses include instrumentation signal selection, data-acquisition systems, industrial control interfaces, test and measurement equipment, and analog signal routing where several sources share a common processing chain. The dual-circuit organization can route two independent signal groups or provide two complementary multiplexed paths on the same board. PCB design should preserve the 16-pin PDIP footprint and route each analog input directly to its intended pin. Keep sensitive analog traces away from digital address and control lines, provide clean supply decoupling, and use short connections to minimize parasitic capacitance. Verify the selected supply and input ranges against the MAX309 datasheet before connecting external signals. This page combines manufacturer product information, distributor listings, same-family drop-in candidates, application guidance, and practical design notes to support component selection and PCB implementation.

RFC Hubungi kami
MAX310CPE+ - 8-Channel CMOS RF Video Multiplexer | Maxim
MAX310CPE+

MAX310CPE+ - 8-Channel CMOS RF Video Multiplexer | Maxim

The Maxim Integrated MAX310CPE+ is an 8-channel CMOS RF and video multiplexer packaged in a 16-pin PDIP. It is designed to route multiple RF or video signals through a shared signal path while maintaining a compact through-hole footprint. The device is listed in production by Analog Devices, and the MAX310 family is identified as a CMOS RF/video multiplexer. An RF or video multiplexer is an interface IC that connects several signal sources to one destination or selects one input path for downstream processing. In the signal-chain hierarchy, the MAX310 belongs to analog switches, interface ICs, and broader semiconductor signal-routing systems. Its 8-channel architecture is useful when several sources must be combined or selected without duplicating downstream receivers, tuners, or measurement equipment. The MAX310CPE+ combines an 8-channel multiplexer configuration with CMOS construction and a 16-pin PDIP package. Through-hole mounting makes it suitable for legacy boards, laboratory instruments, educational equipment, prototypes, and industrial systems that use conventional plated-through-hole PCB footprints. The C designation identifies the temperature-grade family, while the E suffix denotes the 16-pin PDIP package in Maxim Integrated's device naming system. The MAX310 family is intended for RF and video signal routing rather than general-purpose logic. Designers must account for the operating-frequency range, insertion loss, isolation, channel capacitance, switch resistance, supply requirements, control logic, and package-level thermal performance when laying out a new board. These electrical characteristics determine whether the multiplexer preserves signal integrity in the intended RF or video environment. Typical uses include RF test systems, video-source selection, broadcast and surveillance equipment, cable-TV signal routing, instrumentation, and educational RF laboratories. In each case, the eight-channel organization can reduce the number of separate switching paths or provide source selection ahead of a common receiver. The MAX310CPE+ is also useful for maintaining older through-hole designs where a surface-mount multiplexer would not fit the existing board. For a new design, confirm the complete pinout and signal ratings in the manufacturer MAX310 datasheet before routing the PCB. Maintain short RF traces, use a controlled reference plane, decouple the supply connection according to the datasheet guidance, and keep high-speed or high-frequency routes away from noisy switching nodes. Validate the finished channel performance with the intended source impedance and termination scheme. This product page combines the MAX310 family identity, exact MAX310CPE+ ordering code, package information, lifecycle indication, sourcing links, and practical implementation guidance. It also distinguishes the true 16-pin PDIP variant from parts that use other packages and identifies why a footprint-compatible replacement must be selected from the pin-description table rather than by function alone.

RFC Hubungi kami
MAX310CWN+ - 8-Channel RF Video Multiplexer | Analog Devices
MAX310CWN+

MAX310CWN+ - 8-Channel RF Video Multiplexer | Analog Devices

The Analog Devices MAX310CWN+ is an 8-channel CMOS RF/video multiplexer in an 18-pin SOIC package. The device provides a single 8:1 multiplexing function for routing video or RF signals, making it suitable for video switching, signal selection, test equipment, and instrumentation systems. The MAX310 family is identified by the manufacturer as a CMOS RF/video multiplexer, while the MAX310CWN+ order code is associated with the 18-SOIC configuration. A multiplexer is a switching component that connects one signal path to one of several possible signal paths. An 8:1 RF/video multiplexer is therefore positioned between multiple source signals and a shared destination, allowing a system to select among eight inputs instead of duplicating downstream amplification and routing circuitry. This is useful in cameras, video test systems, measurement equipment, and other applications where the selected source must remain compatible with the connected receiver. The MAX310CWN+ is identified as a single-channel, 8:1 analog multiplexer. Its CMOS implementation is intended for RF and video signal routing, where low-noise signal handling and predictable channel selection are important. The device is available in an 18-pin SOIC package, a surface-mount package that supports conventional PCB assembly and provides a practical option for compact analog switching systems. The manufacturer product page lists the MAX310 as a production 8-channel CMOS RF video multiplexer and provides the product selection table, data sheet, sample and buy resources, and supporting documentation. The distributor listing describes the MAX310CWN+ as a video switch IC with one channel in an 18-SOIC package. Use the manufacturer data sheet for the exact electrical ratings, control logic, insertion loss, isolation, bandwidth, on-resistance, supply requirements, and pin-level truth table before finalizing a circuit. In a typical design, the selected source is connected to the common output, while the eight input paths are driven by the source being tested or displayed. The device should be placed close enough to the controlled signal sources to minimize board-level interference and trace loss. Keep sensitive video or RF routing on controlled-impedance structures when signal integrity matters, and route control traces away from analog and RF paths where practical. The main design consideration is verification of the exact MAX310CWN+ configuration, including supply voltage, control-pin polarity, and the pinout associated with the 18-SOIC package. Do not assume that a similar MAX310 order code has identical enable logic, pin assignment, or electrical limits. Consult the pin-description table and typical application circuit in the manufacturer data sheet when assigning PCB tracks. This product page organizes the MAX310CWN+ identity, package information, sourcing guidance, alternatives, and application-oriented engineering notes. It is intended to help engineers locate the correct manufacturer documentation and make a documented replacement decision rather than relying only on a generic video-switch description.

RFC Hubungi kami
MAX310EWN+ - 8:1 CMOS RF/Video Multiplexer | Maxim
MAX310EWN+

MAX310EWN+ - 8:1 CMOS RF/Video Multiplexer | Maxim

The Maxim Integrated MAX310EWN+ is an 8-channel CMOS RF/video multiplexer with one 8:1 selection path, 250 ohm on-state resistance, and operation from negative or positive dual supplies spanning -16.5 V to -4.5 V and 4.5 V to 16.5 V. The device is packaged in an 18-pin SOIC for surface-mount assembly. A video multiplexer is an interface integrated circuit that routes one of several analog video sources to a shared output. The MAX310EWN+ belongs to the broader RF/video switch and signal-routing hierarchy, where an analog switch or multiplexer selects a source without requiring separate downstream receivers for every input. CMOS construction supports low-power operation and consistent signal-path behavior across negative and positive supply rails. The principal feature set includes eight selectable RF/video channels, a single multiplexed output path, and 250 ohm on resistance. Its ability to operate with either negative or positive supply voltage is useful in systems using bipolar signal paths, legacy video equipment, or mixed analog environments. The industrial temperature grade and surface-mount SOIC package support compact, automated PCB assembly. Signal integrity depends on keeping the selected path short and providing a stable return connection. Although the switch resistance is suitable for many video-routing applications, cable capacitance, source impedance, trace geometry, and the impedance of the connected receiver can influence edge response. Grounding, bypass capacitance, and connector placement should therefore be treated as parts of the complete switching network rather than separate mechanical concerns. Typical uses include analog video source selection, RF test-equipment routing, broadcast and professional video signal routing, instrumentation channel selection, and legacy computer-video interfaces. The MAX310EWN+ is most appropriate when an eight-input multiplexer is required in an 18-pin surface-mount design and when bipolar supply operation matches the surrounding circuitry. For layout, assign each signal pin directly to its corresponding connector or source network, keep the mux input and output routes short, and provide local supply bypassing. Check the complete datasheet for control logic levels, break-before-make behavior, channel capacitance, leakage, and timing before using the device in precision or high-frequency systems. This page consolidates the identified electrical characteristics, package details, functional alternatives, and practical layout guidance for engineers evaluating the MAX310EWN+. It also distinguishes the explicitly documented drop-in candidate from related multiplexers that use a different package or function and therefore are not direct replacements.

RFC Hubungi kami
MAX311CWN+ - 8-Channel CMOS RF Video Multiplexer | Analog Devices
MAX311CWN+

MAX311CWN+ - 8-Channel CMOS RF Video Multiplexer | Analog Devices

Analog Devices MAX311CWN+ is an 8-channel CMOS RF video multiplexer with a dual 4:1 configuration, 150 ohm on-resistance, and operation across positive and negative supply ranges of +4.5 V to +16.5 V and -16.5 V to -4.5 V. The device is packaged in an 18-pin SOIC for surface-mount PCB integration. An RF video multiplexer is a semiconductor switch used to route multiple high-frequency or video signals through a shared signal path. Within the broader interface-IC hierarchy, the MAX311 belongs to the analog switch and multiplexer family, where CMOS switching elements control signal routing. Its dual 4:1 organization allows several sources to be selected toward downstream receiver, test, or signal-processing circuitry. The MAX311CWN+ supports positive and negative supply rails, making it suitable for systems that require both polarities. Its specified 150 ohm on-resistance provides a defined impedance for routing calculations, while the eight-channel architecture consolidates multiple signal paths into one package. The 18-pin SOIC package supports conventional surface-mount assembly and is compatible with automated PCB manufacturing processes. According to the Analog Devices MAX311 product page, the MAX311 is in production and is described as an 8-channel CMOS RF video multiplexer. Product documentation identifies the family as MAX311 with a data sheet revision of 0, but engineers should verify the complete pin description, control truth table, switching timing, bandwidth, channel capacitance, and absolute maximum ratings in the manufacturer data sheet before finalizing a design. Typical uses include professional video routing, RF test equipment, video signal selection, broadcast and monitoring systems, and instrumentation that must choose among several RF or video inputs. The dual 4:1 structure can support paired routing or channel-selection functions when the system architecture requires two independent groups of four inputs. The primary design consideration is signal integrity. Keep traces short, use a controlled-reference-ground layout, and account for the 150 ohm on-resistance when driving downstream inputs. Decoupling and protection requirements should follow the manufacturer application guidance because incorrect supply sequencing or signal overvoltage can damage a high-frequency analog switch. This product page combines the manufacturer product identity, exact package and supply information, a confirmed direct replacement, practical routing guidance, and a structured comparison with less suitable interface alternatives. It supports faster component selection while preserving the checks needed for reliable RF and video circuit implementation.

RFC Hubungi kami
MAX311EPE - 8-Channel RF Video Multiplexer | Maxim Integrated
MAX311EPE

MAX311EPE - 8-Channel RF Video Multiplexer | Maxim Integrated

The Maxim Integrated MAX311EPE is an 8-channel CMOS RF/video multiplexer packaged in a 16-pin DIP. The device is designed to route one of eight input signals to a common output, with an on-resistance of up to 250 ohms and switching times of up to 1 microsecond. According to the manufacturer datasheet, the MAX311 family provides off-channel isolation guaranteed at -66 dB at 5 MHz and typical power consumption of 1.1 mW when operated with plus or minus 15 V power supplies. An RF/video multiplexer is a signal-routing semiconductor that selects among multiple analog inputs and connects the selected channel to an output. In the broader hierarchy, it belongs to the switch and multiplexer family, the interface IC category, and ultimately the semiconductor and signal-path component classes. This distinction from a digital multiplexer is important: the MAX311EPE carries analog or RF signals and therefore depends on off-state isolation, on-state resistance, bandwidth, and switching speed rather than digital logic levels. Key features include eight multiplexed channels, CMOS construction, a maximum on-resistance of 250 ohms, and maximum on and off times of 1 microsecond. The high-frequency isolation characteristic helps prevent an unselected input from coupling energy into the selected output. With positive and negative 15 V supplies, the supported input signal range extends from +12 V to -15 V, allowing bipolar analog signals to be routed while the device remains in the analog signal path. Technically, the MAX311EPE uses complementary CMOS switching structures to control the analog channels. When one address is asserted, the corresponding input is connected to the output; the address decoder and enable logic determine which channel conducts. The -66 dB off-isolation guarantee at 5 MHz is especially relevant when adjacent sources carry high-frequency video or RF content, because it limits crosstalk between the active and inactive inputs. The 250-ohm maximum on resistance must also be included in gain-loss and impedance calculations for downstream receivers. Typical applications include video test equipment, RF signal-routing systems, instrumentation, broadcast and professional video interfaces, and analog measurement setups where several signal sources must share a receiver or analyzer. The MAX311EPE is most appropriate where bipolar signal handling and channel isolation matter more than very low on resistance. Systems operating at substantially higher frequencies or requiring lower insertion loss should verify bandwidth and impedance behavior against the complete circuit rather than relying only on the isolation rating. A key design consideration is the interaction between switching transients, grounding, and downstream input capacitance. Keep the selected signal path short, maintain a low-impedance return connection, and use the manufacturer pin-description table when assigning address and control traces. Verify the positive and negative supply sequencing requirements, bypass each supply rail close to the device, and account for the 1-microsecond maximum transition time when the muxed receiver cannot tolerate channel-switch transients. This page combines the available manufacturer-level electrical characteristics, packaging information, sourcing guidance, and application engineering notes into a design-oriented overview. It also highlights where a replacement must be checked against the original 16-pin DIP footprint, pin functions, supply arrangement, signal range, isolation, on-resistance, and switching timing rather than being selected from channel count alone.

RFC Hubungi kami
MAX311EWN+ 8-Channel CMOS RF Video Multiplexer | Analog Devices
MAX311EWN+

MAX311EWN+ 8-Channel CMOS RF Video Multiplexer | Analog Devices

Analog Devices MAX311EWN+ is an 8-channel, CMOS RF video multiplexer designed for routing high-frequency video signals in electronic systems. The device is offered in an 18-pin wide SOIC package for surface-mount assembly, with production documentation identified on the manufacturer product page. Its multiplexed switching architecture makes it applicable to video test equipment, imaging systems, broadcast equipment, and other RF or video signal-routing designs where one of several channels must be selected by control logic. A video multiplexer is a semiconductor switching device that connects multiple signal inputs to a common output path. In the product hierarchy, the MAX311EWN+ is an analog switch and multiplexer IC, which is a type of interface IC used to route high-speed signals under digital control. The MAX311 family is identified by Analog Devices as an 8-channel CMOS RF/video multiplexer. The wide SOIC package provides a practical option for conventional PCB assembly and offers enough mechanical spacing for production inspection compared with a fine-pitch package. The MAX311EWN+ uses CMOS switching circuitry to control RF or video signal paths. CMOS implementation is suited to high-input-impedance systems because it can provide low loading on the source signals while accepting digital control inputs from a controller. The multiplexing function can reduce the number of separate downstream receivers, comparators, or signal-processing channels required when several sources must be routed through a common processing chain. Primary applications include video measurement systems, multimedia routing, broadcast and professional video equipment, camera and imaging test setups, RF test fixtures, and compact embedded video systems. The 8-channel configuration allows a controller to scan or select among multiple sources, making the device useful in automatic test equipment where repetitive routing is required. Designers should also evaluate signal attenuation, isolation, switching speed, bandwidth, control levels, and channel count against the specific source impedance and termination network. For PCB implementation, place the device close to the routed signals and provide a continuous ground reference around the package. Keep high-frequency video traces short and use controlled-impedance routing when trace geometry or dielectric properties affect signal quality. Decoupling near the supply pins should follow the capacitor-selection and placement guidance in the manufacturer data sheet. The control traces should be kept away from sensitive analog paths to minimize switching transients and unintended coupling. This page organizes the manufacturer identification, exact orderable MPN, package information, functional requirements, application guidance, comparison parameters, and engineering considerations into a practical procurement and design reference. It also distinguishes the verified drop-in replacement from package or channel-count mismatches, helping engineers avoid substitutions that appear similar but would require PCB changes or redesign.

RFC Hubungi kami
MAX312EUE+ - Quad 10Ω SPST Analog Switch | Analog Devices
MAX312EUE+

MAX312EUE+ - Quad 10Ω SPST Analog Switch | Analog Devices

Analog Devices MAX312EUE+ is a four-circuit CMOS analog switch with a 1:1 SPST topology, 10Ω maximum on-resistance, and a 16-pin TSSOP package. The device provides four independently controlled switches that conduct equally well in either signal direction, making it suitable for routing analog, digital, and low-voltage instrumentation signals. An analog switch is an integrated semiconductor device that connects or disconnects a signal path under digital control. The MAX312EUE+ belongs to the analog switch and multiplexer hierarchy within interface ICs, providing a defined on-state resistance, off-state leakage, and logic-controlled switching behavior. Its four-channel structure consolidates multiple point-to-point routing functions into one package. Key features include a maximum on-resistance of 10Ω and on-resistance matching of 1.5Ω between channels. Matching is important when several switched paths influence one measurement or signal chain because it helps minimize channel-dependent gain errors. The MAX312 also offers low leakage of 2.5nA at +85°C and equal conduction in both directions, allowing flexible signal-routing topology. The four SPST switches use CMOS control inputs, enabling each channel to be placed in a defined connection state independently. Four independent switches can support signal isolation, test-point selection, instrumentation routing, or the connection of external circuit sections to a shared analog node. The 16-pin TSSOP package supports surface-mount PCB assembly while keeping the circuit compact. Typical uses include data-acquisition systems, sensor signal conditioning, automated test equipment, sample-and-hold interfaces, battery-powered instrumentation, and general-purpose analog signal routing. Because the switches support bidirectional conduction, the same device can route either a source signal toward a load or connect a measurement chain back toward its source. PCB design should place the device near the signals it switches and route high-impedance sensor nodes to minimize parasitic capacitance and leakage. Control traces should remain away from sensitive analog inputs, and unused control inputs should be held at defined logic levels. Verify signal amplitude, bandwidth, temperature, and switch current against the manufacturer datasheet before finalizing the routing design. This product page combines the manufacturer’s switch specifications with practical PCB guidance, package details, selection criteria, and same-family drop-in alternatives. The comparison and design notes explain how on-resistance matching, leakage, logic control, and package reuse affect engineering decisions when replacing an existing four-channel analog switch.

RFC Hubungi kami
MAX313CUE+ - Quad SPST CMOS Analog Switch | ADI
MAX313CUE+

MAX313CUE+ - Quad SPST CMOS Analog Switch | ADI

Analog Devices MAX313CUE+ is a quad SPST CMOS analog switch with four independently controlled normally open channels, a maximum on-resistance of 10 ohms, and a 16-pin TSSOP package. It supports single-supply operation from 4.5 V to 30 V and dual-supply operation from -4.5 V to -20 V and +4.5 V to +20 V. Typical on-resistance is 6.5 ohms, while guaranteed channel matching is 1.5 ohms maximum. A CMOS analog switch is a voltage-controlled semiconductor device that routes analog or digital signals between circuit nodes. The MAX313 belongs to the analog switch and multiplexer hierarchy, where an analog switch performs point-to-point routing and a multiplexer connects multiple signals to a common channel. Its SPST configuration provides one normally open path per switch, making it suitable for isolation, signal selection, test-fixture routing, and bidirectional analog-signal control. The four channels can conduct equally well in either direction. The MAX313CUE+ combines low on-resistance with channel-to-channel matching of 1.5 ohms maximum and on-resistance flatness of 2 ohms maximum over the specified signal range. These characteristics help minimize gain error and distortion when several switched channels must present similar resistance to downstream circuitry. It also provides low leakage and low power consumption for precision and power-sensitive systems. The MAX313 family operates from a wide supply range and supports rail-to-rail signal handling. According to the Analog Devices MAX313 product page, the devices are pin compatible with the DG411, DG412, and DG413 families. The manufacturer also specifies guaranteed ESD protection greater than 2000 V per Method 3015.7 and crosstalk above 96 dB at 20 kHz, helping protect sensitive analog paths and limit interaction between adjacent channels. Typical uses include precision test and measurement systems, analog signal-conditioning modules, battery-powered instrumentation, industrial control interfaces, and signal-isolation networks. The device can route sensor outputs, test signals, or external inputs without introducing the continuous power loss associated with a permanently conducting analog path. It is particularly useful when signal integrity, repeatable channel resistance, and low off-state leakage are more important than maximum switching speed. When laying out a MAX313CUE+ board, follow the TSSOP-16 pin-assignment table in the manufacturer datasheet and keep high-impedance routes short to minimize leakage pickup. Place supply decoupling close to the device, and evaluate switching transients when the source impedance is high. The normally open architecture requires the correct drive polarity at each control input; consult the control-input truth table before changing logic levels. This product record combines the manufacturer specifications, package information, replacement references, and practical design guidance into one engineering-focused view. It also identifies same-package alternatives and explains when their electrical or environmental differences matter, helping designers select the correct switch without introducing a footprint change.

RFC Hubungi kami
MAX314CPE+ - Quad SPST Analog Switch | Analog Devices
MAX314CPE+

MAX314CPE+ - Quad SPST Analog Switch | Analog Devices

The Analog Devices MAX314CPE+ is a four-circuit CMOS analog switch with four independently controlled SPST channels, a maximum on-resistance of 10 ohms, and a 16-pin PDIP package. Each switch conducts equally well in either direction, making the device suitable for routing analog, digital, and low-frequency instrumentation signals. An analog switch is a solid-state semiconductor device that connects or isolates circuit paths under electrical control. Unlike a mechanical relay, it operates without moving contacts, enabling fast switching and compact integration. The MAX314CPE+ belongs to the CMOS analog-switch hierarchy and provides four SPST channels in a through-hole package for applications that require signal routing rather than continuous power conversion. The device has a maximum on-resistance of 10 ohms and on-resistance matching between channels of 1.5 ohms. Its low leakage of 2.5 nA at +85°C helps preserve signal integrity in high-impedance circuits. Bidirectional conduction expands routing flexibility, while low power consumption supports both portable and fixed equipment. ESD tolerance greater than 2000 V per Method 3015.7 adds handling protection during assembly. Each of the four switch channels provides a separate control path, allowing a system to isolate a sensor, select a measurement route, or disconnect an external interface. The parallel CMOS structure avoids mechanical contact delay or wear, while the specified resistance matching helps limit channel-dependent gain and attenuation errors when multiple inputs are routed through the device. Typical uses include analog signal multiplexing in test and measurement equipment, channel isolation in data-acquisition systems, switching between sensors and amplifiers, and routing control signals in industrial control boards. The 16-pin PDIP package is particularly useful for prototypes, through-hole assemblies, and designs where a socketed or manually solderable package simplifies maintenance. When laying out the circuit, place each switched node close to its source and destination where practical, and avoid sharing long copper paths between sensitive channels. Confirm signal amplitude, leakage requirements, control logic levels, and switching transients against the manufacturer data sheet. The MAX314CPE+ is especially appropriate when four separately controlled, bidirectional, normally open analog paths are needed in a conventional through-hole design. This product page combines the manufacturer specifications, sourcing details, pin-package information, and practical selection guidance. It also identifies same-family alternatives while distinguishing verified drop-in choices from options that require a footprint or interface review before substitution.

RFC Hubungi kami
MAX3160EAP+ - 3.0-5.5V Multiprotocol Transceiver | Analog Devices
MAX3160EAP+

MAX3160EAP+ - 3.0-5.5V Multiprotocol Transceiver | Analog Devices

The Analog Devices MAX3160EAP+ is a 3.0V to 5.5V RS-232/RS-485/RS-422 multiprotocol transceiver with a 20-pin SSOP package. It is programmable as a two-transmitter, two-receiver RS-232 interface or as a single RS-485/RS-422 transceiver, allowing one physical interface circuit to support multiple serial protocols. The device also supports pin-selectable transmitter slew rates for RS-232 and RS-485/422 operation, helping reduce EMI and cable reflections. Analog Devices identifies the MAX3160 family as a low-power multiprotocol interface solution, with a listed 1 uA operating-current feature and data rates up to 250 kbps for suitable operation. The MAX3160EAP+ is packaged as a 20-SSOP surface-mount device. Its protocol configurability makes it useful in industrial controls, interface converters, networking peripherals, point-of-sale equipment, and security systems where a board must accommodate legacy RS-232 alongside balanced RS-485 or RS-422 links. The MAX3160 family is pin-programmable, so the same PCB can be configured differently during assembly or test. Compared with a fixed RS-232 transceiver, the MAX3160EAP+ adds RS-485/RS-422 capability and selectable slew-rate control in one interface IC. Its low operating-current positioning is important for portable and space-constrained equipment, while the SSOP footprint simplifies integration with conventional surface-mount assembly. Design decisions should confirm the selected protocol, termination requirements, cable length, data rate, and logic-level compatibility against the manufacturer datasheet.

RFC Hubungi kami
MAX31856MUD+ Precision Thermocouple Converter | Analog Devices
MAX31856MUD+

MAX31856MUD+ Precision Thermocouple Converter | Analog Devices

The Analog Devices MAX31856MUD+ is a precision thermocouple-to-digital converter with cold-junction compensation, digital linearization, Celsius-formatted output, and a 14-TSSOP package. The verified source data identifies 0.0078125°C resolution and supports readings from -55°C to 125°C for the listed device context, with thermocouple measurements reaching as high as +1800°C. It converts thermocouple signals into digital temperature data while supporting multiple thermocouple types through device configuration. A thermocouple-to-digital converter is an interface IC that conditions a low-voltage thermoelectric voltage, performs cold-junction compensation, applies the appropriate linearization for the selected thermocouple type, and transfers temperature data to a host controller. The MAX31856 belongs to the sensor and detector interface category and sits between physical temperature sensors and digital embedded systems. Its digital interface makes temperature monitoring suitable for industrial equipment, test systems, control loops, and embedded instrumentation. The verified manufacturer result identifies cold-junction compensation, thermocouple signal digitisation, linearization, Celsius output format, and 0.0078125°C resolution as central features. The device is supplied in a 14-pin TSSOP package, with the MUD+ ordering code shown by DigiKey as a thermocouple-to-digital converter IC. The source material does not provide a complete verified set of electrical limits, SPI timing values, thermocouple input ranges for every type, or package dimensions, so those values are not inferred here. Because a thermocouple measures the temperature difference between a sensing junction and a reference junction, cold-junction compensation is essential for accurate measurements near ambient temperature. The MAX31856 handles this function internally, allowing the host system to receive compensated digital temperature data rather than raw thermocouple voltage. Digital linearization further reduces the software burden associated with converting nonlinear thermocouple voltage into temperature. Typical uses include industrial furnace monitoring, temperature-controlled processes, laboratory equipment, environmental monitoring, and embedded thermal control. In each case, the thermocouple type, wiring, cold-junction implementation, grounding strategy, and digital interface configuration must be selected according to the manufacturer's datasheet. The verified data does not identify a specific companion MCU or application reference design, so companion products are not asserted as manufacturer-recommended parts. The principal design consideration is ensuring that the selected thermocouple, input filtering, grounding, and digital interface match the system measurement range. For thermocouple signals, keeping the analog input path away from switching nodes and noisy digital return currents helps preserve measurement integrity. This page consolidates verified distributor listings, the official Analog Devices product page, and the available cross-reference information without inventing missing electrical parameters.

RFC Hubungi kami
MAX318CPA+ - 35 Ohm SPST CMOS Analog Switch | Analog Devices
MAX318CPA+

MAX318CPA+ - 35 Ohm SPST CMOS Analog Switch | Analog Devices

The Analog Devices MAX318CPA+ is a precision, normally open, single-pole single-throw CMOS analog switch with an on-resistance of 35 ohms, housed in an 8-pin PDIP package. It routes one analog signal using a 1:1 SPST topology and is designed for precision signal-selection and test systems. An analog switch is a semiconductor interface device that connects or disconnects an analog signal path under digital control. The MAX318CPA+ belongs to the analog switch hierarchy within interface ICs and multiplexers, providing a simpler alternative to a multi-channel multiplexer when only one signal path must be selected. Its normally open configuration keeps the switched node disconnected until the control input activates the path. Key characteristics include a maximum on-resistance of 35 ohms, operation from 4.5 V to 20 V, and normally open SPST behavior. The device is specified as a precision CMOS analog switch with low on-resistance that remains substantially flat across the analog signal range. According to the Analog Devices MAX318 product page, on-resistance is guaranteed below 35 ohms and is matched within 2 ohms between channels in the associated precision-switch family. The MAX318CPA+ is intended for precision instrumentation, signal routing, test and measurement equipment, industrial control interfaces, and data acquisition systems. Its single-channel architecture simplifies control logic while preserving the low resistance required to transfer low-level or precision analog signals. The 8-pin PDIP package also supports conventional through-hole assembly and prototype boards where fine-pitch surface-mount routing would be inconvenient. Designers should verify the control logic, supply voltage, allowable signal voltage, and switching transients against the manufacturer data sheet before use. Because an analog switch can introduce small resistance variation, channel resistance matching, charge injection, off leakage, and bandwidth determine whether it is suitable for a particular signal path. Input and output protection may also be required when external voltages exceed the device ratings. This page combines the manufacturer specifications, verified sourcing links, application guidance, comparison information, and practical design notes to support component selection and PCB implementation. The MAX318CPA+ is best suited to designers who need a simple, normally open, precision SPST switch rather than a multi-channel multiplexer.

RFC Hubungi kami
MAX319CSA+ - Precision 35Ω CMOS SPDT Switch | Analog Devices
MAX319CSA+

MAX319CSA+ - Precision 35Ω CMOS SPDT Switch | Analog Devices

The Analog Devices MAX319CSA+ is a precision, single-pole double-throw CMOS analog switch with one normally open and one normally closed path, a maximum on-resistance of 35Ω, and an 8-pin SOIC package. It is designed for precision signal routing where low on-resistance, low charge injection, low power consumption, and high electrostatic-discharge withstand are important. An analog switch is a semiconductor interface that routes an analog signal between circuit nodes under digital control. Unlike a relay, it operates electronically at low voltage and can switch signals rapidly without mechanical wear. The MAX319 belongs to the broader analog-switch hierarchy, which sits alongside multiplexers, demultiplexers, and interface ICs used to connect sensors, test equipment, measurement systems, and signal-processing electronics. Key electrical characteristics include on-resistance below 20Ω typical and 35Ω maximum, guaranteed channel matching within 2Ω, and on-resistance variation of no more than 3Ω maximum across the analog signal range. Charge injection is low at 10pC, while power consumption is 35µW. These characteristics help preserve signal fidelity when the switch is used in measurement, control, or data-acquisition paths. The MAX319 family uses an improved silicon-gate CMOS process and rail-to-rail analog signal handling capability associated with a 44V maximum breakdown voltage. Its precision configuration is useful when signal-source impedance, leakage, or switch resistance could otherwise influence the measurement result. The MAX319CSA+ ordering code identifies the 8-pin SOIC package and the manufacturer's standard production configuration. Typical uses include battery-powered instrumentation, automated test equipment, analog measurement systems, signal-path routing, sample-and-hold circuits, and industrial control interfaces. Its low 35µW power consumption is particularly useful in portable equipment, while the 35Ω maximum on-resistance is suitable for moderate-impedance analog signals rather than ultra-low-impedance precision dividers. When designing a circuit around the MAX319CSA+, account for the switch's on-resistance, leakage, charge injection, and off-state behavior when calculating signal attenuation and timing. Place the device close to sensitive signal paths, maintain adequate grounding, and use the manufacturer pin-description table when assigning PCB tracks. Verify the logic levels and control polarity against the actual device documentation before finalizing the layout. This product page combines the manufacturer's device specifications with practical design guidance, package information, sourcing details, and a conservative drop-in assessment. It emphasizes verified distinctions between electrically similar devices so engineers can determine whether a replacement preserves both the board footprint and the required switch behavior.

RFC Hubungi kami
MAX3221CAE+ - 3 to 5.5V RS-232 Transceiver | Analog Devices
MAX3221CAE+

MAX3221CAE+ - 3 to 5.5V RS-232 Transceiver | Analog Devices

Analog Devices MAX3221CAE+ is a one-driver, one-receiver RS-232 transceiver designed for +3V to +5.5V operation and supplied in a 16-pin SSOP package. It provides 1 µA supply current when AutoShutdown is active, while integrating the charge-pump circuitry required to generate RS-232-compatible driver levels from a low-voltage supply. The MAX3221CAE+ is suitable for portable equipment, industrial controls, data acquisition systems, and other equipment that requires a compact, low-power serial interface. An RS-232 transceiver is an interface IC that combines a transmitter and receiver for communicating between a logic-level device and an RS-232 port. The transmitter converts low-voltage TTL or CMOS signals into RS-232 levels, while the receiver converts incoming RS-232 signals back into logic-compatible levels. The MAX3221 family belongs to the interface IC hierarchy and provides a practical way to bridge modern embedded systems with legacy RS-232 equipment. The MAX3221CAE+ includes Maxim's AutoShutdown feature, allowing the on-board power supply and driver circuitry to shut down when the receiver does not detect a valid signal. According to the Analog Devices MAX3221 product page, the device operates from +3V to +5.5V and reaches a supply current of 1 µA. These characteristics are particularly valuable in battery-powered instruments where a permanently active RS-232 interface would increase standby power consumption. The MAX3221 is a 1-driver/1-receiver 16-pin SSOP version of the 2-driver/2-receiver MAX3223. Its integrated RS-232 supply uses charge-pump circuitry to develop the voltage swing needed by the transmitter. The C designation denotes the family's capacitor configuration, while the E designation provides shutdown-control functionality. The A suffix identifies the package and temperature-related ordering configuration used in the MAX3221CAE+ ordering code. Typical applications include battery-powered test equipment, handheld configuration tools, serial adapters, industrial instrumentation, point-of-sale equipment, and embedded systems that must communicate with a host computer through an RS-232 port. The 16-pin SSOP footprint is useful for compact designs, although engineers should verify connector protection, cable length, logic levels, and supply compatibility against the system requirements. The principal design consideration is signal integrity. RS-232 is a single-ended, unbalanced interface, so cable routing and ground quality can materially affect noise immunity. Place the transceiver close to the interface connector, provide a low-impedance ground path, use suitable protection for exposed cables, and observe the manufacturer's recommended charge-pump capacitor values. External circuitry may also be required for hardware handshaking or for conditioning signals on long or electrically noisy cables. This page organizes the MAX3221CAE+ specifications, application guidance, package information, and verified same-package alternatives into an engineering-focused reference. It also highlights the practical trade-offs among shutdown, supply-voltage, capacitance, and temperature variants so designers can make a replacement decision based on actual circuit requirements rather than package similarity alone.

RFC Hubungi kami