Produk (44,000+)

MAX3380ECUP+T - 2Tx/2Rx RS-232 Transceiver | Analog Devices
MAX3380ECUP+T

MAX3380ECUP+T - 2Tx/2Rx RS-232 Transceiver | Analog Devices

The Analog Devices MAX3380ECUP+T is a 2-transmitter, 2-receiver RS-232 transceiver designed for +2.35 V to +5.5 V operation, with a 20-pin TSSOP package and enhanced electrostatic-discharge protection on both logic and RS-232 pins. It supports EIA/TIA-232 and V.28/V.24 communication interfaces while operating from a 1.65 V logic reference where required. An RS-232 transceiver is an interface IC that converts between single-ended TTL/CMOS logic signals and differential bipolar RS-232 signals. It belongs to the interface-IC hierarchy, connecting UART, UART-compatible controllers, microcontrollers, and industrial peripherals to physical communication links. Transceivers combine driver and receiver functions in one package, reducing board area and simplifying bidirectional serial-port implementations. The MAX3380ECUP+T provides two transmit channels and two receive channels, allowing two serial ports to share one device. Its +2.35 V to +5.5 V supply range accommodates modern 3.3 V and 5 V systems, while the VL pin provides logic-level interoperability in mixed-voltage environments down to 1.65 V. The manufacturer describes enhanced ESD protection on the TTL and RS-232 sides, with the distributor listing identifying 15 kV ESD protection on I/O and logic pins. The device combines low-power operation with high data-rate capability, making it suitable for compact communications equipment. Its integrated charge-pump circuitry supports RS-232 signal generation without a separate external DC-DC converter. Logic input and output levels are referenced to VL, allowing the interface thresholds to track a compatible mixed-logic supply rather than being tied to one fixed rail. Typical uses include industrial serial controllers, point-of-sale equipment, test and measurement instruments, medical-device consoles, security systems, and other embedded systems that exchange data over RS-232. A system can connect two UART channels to the MAX3380ECUP+T while providing shared ground wiring, proper signal polarity, and compliant cable termination. PCB layout should keep RS-232 traces away from clocks, switching supplies, and high-speed digital nets. Confirm logic thresholds against the connected UART voltage, observe the manufacturer’s charge-pump capacitor requirements, and provide the specified supply and bypass capacitance close to the device pins. This page combines the manufacturer interface description, package and ordering information, drop-in alternatives, comparison parameters, and practical PCB guidance to support faster component selection and implementation.

RFC Hubungi kami
MAX3380EEUP+ - 2/2 RS-232 Transceiver | Analog Devices
MAX3380EEUP+

MAX3380EEUP+ - 2/2 RS-232 Transceiver | Analog Devices

Analog Devices MAX3380EEUP+ is a 2-transmitter, 2-receiver RS-232 transceiver designed for +2.35 V to +5.5 V operation, with 15 kV ESD protection on both the RS-232 and logic pins and support for data rates up to 460 kbps. The device is offered in a 20-pin TSSOP package. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and differential bipolar RS-232 signals. It belongs to the transceiver class, then to the broader interface IC and semiconductor hierarchy. This bidirectional interface is useful when equipment must communicate over longer cable distances, tolerate ground-offset differences, or meet the electrical characteristics associated with EIA/TIA-232 and V.28 communications. The MAX3380EEUP+ uses a low-dropout transmitter output stage and a dual charge pump. These features allow RS-232-compatible output levels from supplies below +3.1 V and down to +2.35 V without increasing supply current when the supply lies within that range. Its +5.5 V maximum operating voltage also makes it suitable for systems powered from a single lithium-ion cell or a low-voltage regulated rail. The four-driver, four-receiver naming in some listings refers to two transmit channels and two receive channels rather than four independent full-duplex ports. Both RS-232 I/O pins and logic-side pins receive enhanced electrostatic-discharge protection. Typical system-level uses include data acquisition equipment, industrial controllers, service interfaces, embedded serial ports, and instrumentation that requires a compact, low-voltage RS-232 connection. For board design, treat the transmitter outputs and receiver inputs as externally exposed communication pins even when the logic-side pins are protected. Keep the interface connector and cable path away from sensitive analog circuitry, provide the required bypass capacitance close to the supply pins, and route the differential transmission traces as a pair. The transmitter should connect to the remote RS-232 port through protection and signal-conditioning components appropriate to the required surge and ESD levels. MAX3380EEUP+ is appropriate when a board needs two RS-232 receive channels and two RS-232 transmit channels from a compact, low-power interface IC. Verify cable length, data rate, connector protection, and grounding before deployment. This page combines the product specifications, qualified package details, sourcing information, replacement guidance, and practical RS-232 design considerations into a focused engineering reference.

RFC Hubungi kami
MAX3381ECUP+ - 2Tx/2Rx RS-232 Transceiver | Analog Devices
MAX3381ECUP+

MAX3381ECUP+ - 2Tx/2Rx RS-232 Transceiver | Analog Devices

Analog Devices MAX3381ECUP+ is a 2-transmitter, 2-receiver RS-232 interface transceiver with a +2.35 V to +5.5 V supply range, 15 kV ESD protection on I/O and logic pins, and a 20-TSSOP package. It combines EIA/TIA-232 and V.28/V.24 communication functions with low power requirements and high data-rate capability. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar voltage levels used by RS-232 equipment. Within the interface hierarchy, it belongs to the RS-232 transceiver class, communication interface IC family, and broader semiconductor category. Two transmitters and two receivers allow one device to support a complete point-to-point or multi-drop serial connection when the system bus rules are observed. The MAX3381ECUP+ provides 15 kV ESD protection on both its RS-232 I/O pins and logic pins. This protection is particularly useful in industrial, industrial-control, and equipment environments where cables can be touched or exposed to electrostatic discharge. Its 2.35 V minimum supply voltage also supports systems that cannot rely on a regulated 3.3 V or 5 V rail. The MAX3381E family is designed for low-power operation while retaining high data-rate performance. The integrated charge-pump circuitry required for RS-232 voltage generation is contained in the interface IC, reducing the number of external components needed for a working communication port. The MAX3381ECUP+ is identified as a 2/2 full RS-232 transceiver in a 20-TSSOP package. Typical applications include serial service consoles, data-acquisition equipment, industrial control links, test and measurement instruments, and embedded systems that communicate with legacy RS-232 peripherals. The dual-channel arrangement is useful for designs requiring two serial paths, or one link in each direction, without using two separate interface devices. PCB implementation should preserve the device's pinout and follow the manufacturer layout guidance. Place the required passives close to their associated pins, route the RS-232 traces away from sensitive analog and clock signals, and use suitable protection and grounding practices for cables entering the enclosure. Confirm the exact pin functions and external-component values against the manufacturer datasheet before releasing the layout. This product page consolidates the verified operating range, channel configuration, ESD rating, package information, same-footprint alternatives, and application-oriented design guidance. It is intended to help engineers evaluate the MAX3381ECUP+ quickly while keeping the final schematic, PCB, and component decisions grounded in manufacturer documentation.

RFC Hubungi kami
MAX3381ECUP+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3381ECUP+T

MAX3381ECUP+T - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3381ECUP+T is a 2-transmitter, 2-receiver full-duplex RS-232 transceiver operating from 2.35V to 5.5V, supporting data rates up to 250kbps and providing 15kV ESD protection on I/O and logic pins in a 20-TSSOP package. It combines EIA/TIA-232, V.28, and V.24 interface requirements with low-power operation and integrated level translation. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into digital logic levels. In the broader electronics hierarchy, an RS-232 transceiver belongs to interface ICs and line-driver and receiver devices, where it protects a host controller from the voltage range and electrostatic-discharge exposure of a serial connection. The MAX3381E family supports two transmit channels and two receive channels, allowing full-duplex communication through one package. Its 2.35V minimum supply voltage supports modern low-voltage embedded systems, while the 5.5V maximum accommodates conventional 5V equipment. The 250kbps maximum data rate is suitable for industrial control links, point-of-sale equipment, data acquisition, and service interfaces. Integrated charge-pump circuitry generates the bipolar voltage required to transmit RS-232-compatible levels from a single low-voltage supply. According to the manufacturer datasheet, enhanced electrostatic-discharge protection is provided on both the TTL and RS-232 sides, covering the 15kV ESD-protected I/O and logic pins identified for this device. Typical uses include industrial serial controllers, programmable-logic or microcontroller UART links, instrumentation, and embedded control systems. The two transmitters can support separate outbound channels, while the two receivers allow simultaneous inbound monitoring or redundant communication paths when the connected system requires them. PCB design should provide a solid ground plane, place charge-pump and interface components close to the device, and preserve adequate clearances around connected RS-232 lines. Decoupling capacitors should be placed directly beside the supply pins. The 20-TSSOP footprint is compact, but its narrow lead pitch requires careful inspection and reliable assembly processes. This product page combines operating limits, interface characteristics, application guidance, package details, and same-family drop-in alternatives to support component selection and PCB design before an RS-232 interface is committed to production.

RFC Hubungi kami
MAX3381EEUP+ 2Tx/2Rx RS-232 Transceiver | Analog Devices
MAX3381EEUP+

MAX3381EEUP+ 2Tx/2Rx RS-232 Transceiver | Analog Devices

Analog Devices MAX3381EEUP+ is a 2-transmitter, 2-receiver RS-232 transceiver designed for +2.35 V to +5.5 V operation, with 1 uA supply current, 460 kbps data rate, and ±15 kV ESD protection on its I/O and logic pins. The device is packaged in a 20-pin TSSOP. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and differential bipolar RS-232 signals. It belongs to the transceiver and line-driver hierarchy within interface ICs, allowing equipment with TTL or CMOS logic ports to communicate with RS-232 equipment over a wired serial link. The MAX3381E combines two transmit channels, two receive channels, level translation, and electrostatic-discharge protection in one package. The MAX3381EEUP+ supports supply voltages from +2.35 V to +5.5 V, making it suitable for systems that cannot provide a conventional +5 V rail. Its 460 kbps maximum signaling rate handles common point-to-point serial-control links, while its 1 uA supply current supports low-power equipment. The ±15 kV ESD rating applies to both the RS-232 I/O pins and the logic pins. The MAX3381E family implements powered EIA/TIA-232 and V.28/V.24 communication interfaces. Powered operation means the device includes the charge-pump circuitry required to generate the bipolar voltage levels used by RS-232. This integration reduces the external discrete components normally needed around separate line drivers and receivers, although charge-pump capacitors and interface filtering still require careful PCB planning. Typical uses include industrial control consoles, laboratory instruments, data-acquisition equipment, point-of-sale terminals, and service-port adapters. The two transmitter and two receiver channels suit links requiring two serial paths, while the broad supply-voltage range supports both 3.3 V and 5 V system logic. Cable routing and connector selection remain important because RS-232 is designed for point-to-point communication rather than long multipoint networks. For a new layout, place the device close to the protected connector and route each RS-232 line directly toward its connector pin with a short path. Keep logic-side traces away from the unprotected connector side of the interface. Confirm the device's enable, shutdown, receiver-output, and driver-input states during startup so that unused channels do not create bus contention. This product record combines the manufacturer's MAX3381E family information with package, interface, speed, power, and ESD characteristics for engineering selection. It also provides verified same-package replacement context, practical layout guidance, and application-oriented comparisons that support faster component evaluation before schematic capture.

RFC Hubungi kami
MAX3381EEUP+T - 2/2 RS-232 Transceiver | Analog Devices
MAX3381EEUP+T

MAX3381EEUP+T - 2/2 RS-232 Transceiver | Analog Devices

Analog Devices MAX3381EEUP+T is a 2-transmitter, 2-receiver RS-232 transceiver operating from +2.35 V to +5.5 V, with 15 kV ESD protection on I/O and logic pins, in a 20-pin TSSOP package. The interface supports EIA/TIA-232 and V.28/V.24 communication while operating from a low 1 µA supply current. An RS-232 transceiver is an interface IC that converts low-voltage digital logic signals into RS-232 voltage levels and converts received RS-232 signals back into logic-compatible levels. It belongs to the transceiver and driver/receiver hierarchy, bridging UART, UART-compatible controller, and computer I/O logic with external serial cables. This bidirectional level-shifting function allows a compact system to communicate through a longer-distance, noise-tolerant serial interface. The MAX3381EEUP+T provides two transmit channels and two receive channels, supporting full-duplex point-to-point serial links. Its +2.35 V to +5.5 V operating range supports low-voltage logic systems as well as conventional +5 V equipment. The manufacturer's product page identifies 15 kV ESD protection on both I/O and logic pins, helping protect sensitive interface circuits when cables are connected or disconnected. The MAX3380E and MAX3381E families combine low power consumption with high data-rate capability. The MAX3381E variant is specified for production availability, and its enhanced ESD protection applies to both the RS-232 side and the logic pins. Independent transmit and receive channels allow full-duplex operation when the connected system assigns one driver and one receiver to each communication path. Typical uses include industrial control links, point-of-sale equipment, data-cable interfaces, instrumentation, and embedded serial ports. The dual transmitter arrangement can support two outbound RS-232 signals, while the dual receivers can monitor two incoming signals. In designs using a UART, the device can translate between the controller's logic-level pins and the voltage levels required by an RS-232 cable. When laying out the circuit, place the device close to the RS-232 connector and route driver and receiver traces away from sensitive analog or high-speed digital paths. Verify the connector's signal and ground assignments, provide the required supply bypassing, and maintain adequate board spacing to reduce surge-current exposure at the protected pins. This product page brings together the manufacturer's core electrical characteristics, package information, verified drop-in relationships, and practical interface-layout guidance. It is intended to help engineers evaluate the MAX3381EEUP+T for low-voltage RS-232 links, compare documented replacements, and plan protection and layout before releasing a PCB design.

RFC Hubungi kami
MAX3384ECAP - 250kbps ESD-Protected RS-232 | Analog Devices
MAX3384ECAP

MAX3384ECAP - 250kbps ESD-Protected RS-232 | Analog Devices

Analog Devices MAX3384ECAP is a low-power true RS-232 transceiver with two transmitters and two receivers, operating from a 3.0V to 5.5V single supply and supporting data rates up to 250kbps. Every transmitter output and receiver input provides electrostatic-discharge protection to ±15kV. The device is packaged in a 20-pin SSOP with a 0.65mm pitch. A true RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and differential bipolar RS-232 signals. It belongs to the broader communication-interface hierarchy: RS-232 transceiver → line driver and receiver → interface IC → semiconductor. The MAX3384ECAP combines transmit and receive functions in one package, allowing a compact design to bridge a modern controller or microcontroller with a legacy RS-232 link. The 3.0V to 5.5V operating range supports both 3.3V and 5V digital systems while avoiding the higher supply requirement associated with some older RS-232 devices. Its operation up to 250kbps makes it suitable for data acquisition, industrial control, point-of-sale equipment, and embedded systems that transfer more information than a low-speed serial link. The integrated ±15kV ESD protection strengthens the external interface against electrostatic discharge events. The MAX3384ECAP provides two transmit channels and two receive channels in a single 20-pin SSOP. This channel density allows one transceiver to serve two independent RS-232 directions or multiple device connections. A 3.3V-compatible supply range also simplifies mixed-voltage designs in which the controller core operates below 5V, while the RS-232 interface remains powered from the same rail. Typical applications include industrial serial controllers, point-of-sale terminals, access-control equipment, security systems, laboratory instruments, and embedded data-collection systems. The combination of four I/O channels, a 250kbps maximum signaling rate, low-power operation, and ±15kV interface protection addresses designs that require compact integration without the supply voltage of a legacy 5V-only RS-232 implementation. Designers should pay attention to the device's 0.65mm-pitch SSOP footprint and verify every signal and power connection against the manufacturer pin-description table before layout release. Keep the RS-232 connector-side traces away from sensitive logic where practical, and provide the external charge-pump and interface components specified by the manufacturer datasheet for the selected operating configuration. This product overview combines the MAX3384ECAP's principal electrical, packaging, protection, and interface characteristics with pin-compatible replacement guidance and practical PCB considerations. It supports faster component selection by separating application fit, channel requirements, supply compatibility, and package constraints into directly comparable engineering factors.

RFC Hubungi kami
MAX3384ECWN+ - 250kbps RS-232 Transceiver | Analog Devices
MAX3384ECWN+

MAX3384ECWN+ - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3384ECWN+ is a 3.0V-powered, 2/2 RS-232 transceiver supporting data rates up to 250kbps in a 20-pin SSOP package. It provides two transmit channels, two receive channels, low-power operation, and enhanced electrostatic-discharge protection for reliable point-to-point serial interfaces. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts received RS-232 levels back into digital logic. It belongs to the transceiver hierarchy within interface ICs, providing the physical signaling layer between data-processing equipment and a cable-connected peripheral or system. The MAX3384ECWN+ implements the EIA/TIA-232 and V.28/V.24 signaling requirements described for this device family. The principal features include operation from a 3.0V to 5.5V supply, operation up to 250kbps, two transmit outputs, two receive inputs, and enhanced ESD protection. Low-power requirements make the device suitable for systems in which interface circuitry must coexist with low-voltage digital logic. The manufacturer describes protection on both transmitter outputs and receiver inputs, which is important when cables may be connected, disconnected, or exposed to electrostatic discharge. The MAX3384ECWN+ combines true RS-232 line-driver and receiver functions in one integrated circuit. Its powered-down behavior reduces power consumption when the associated subsystem is inactive. Because the interface operates from a single low-voltage supply while generating compliant RS-232 levels, it can simplify designs that would otherwise require separate external line drivers, receivers, and protection networks. Typical uses include industrial control consoles, point-of-sale terminals, test equipment, instrumentation, and embedded systems that communicate with RS-232 peripherals through cables. The 250kbps capability is useful for moderate-speed serial links, while the integrated two-channel transmitter and receiver arrangement reduces the number of components required for bidirectional or multiport serial interfaces. The principal design consideration is the difference between RS-232 and TTL-level signaling. The MAX3384ECWN+ is intended for the RS-232 side of the connection; it does not directly accept or produce standard TTL or CMOS logic levels. Layout should preserve short return paths and appropriate grounding, while external protection and cable-length considerations should follow the manufacturer's interface guidance. This product page combines the device's core electrical characteristics, verified package information, practical application guidance, and documented same-family replacement options. It also distinguishes true pin-compatible alternatives from broader RS-232 interface products that may use a different package, voltage rating, feature set, or channel arrangement.

RFC Hubungi kami
MAX3384ECWN+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3384ECWN+T

MAX3384ECWN+T - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3384ECWN+T is a 2/2 RS-232 transceiver with a 3.0V to 5.5V supply range, data rates up to 250kbps, and 15kV ESD protection, housed in an 18-pin SOIC package. It combines two transmitters and two receivers in one device, providing bidirectional serial-interface conversion for equipment that communicates through EIA/TIA-232 and V.28/V.24 links. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 levels and converts incoming RS-232 signals back into digital logic levels. It belongs to the interface IC hierarchy, where the transceiver performs the physical signal conversion between a host controller or UART and an RS-232 port. This integration reduces the number of discrete line-driver and receiver components required at the board level. The MAX3384ECWN+T operates from 3.0V to 5.5V, supports data rates up to 250kbps, and provides 15kV ESD protection. The Analog Devices manufacturer page specifies that all transmitter outputs and receiver inputs are protected. Its 18-pin SOIC package supports conventional surface-mount assembly and is suitable for industrial-control, communications, instrumentation, and embedded-system interfaces operating across 0°C to 70°C. The device uses two transmitters and two receivers, allowing two serial channels or full-duplex operation depending on how the interface pins are connected. Because it is a true RS-232 transceiver rather than a differential RS-422 or RS-485 device, its voltage levels and application role are not interchangeable with those bus standards. The 250kbps maximum data rate is suitable for legacy serial equipment, control consoles, POS systems, and industrial peripherals that use EIA/TIA-232. Typical applications include point-of-sale terminals, security and access-control equipment, test and measurement instruments, industrial controllers, and service-console interfaces. The integrated ESD protection is particularly valuable where an exposed serial cable can introduce electrostatic discharge into a control board. The 3.0V minimum supply voltage also helps the device operate alongside modern low-voltage digital systems without requiring a dedicated 5V-only interface rail. PCB design should preserve the datasheet-recommended supply and bypass-capacitor placement while keeping unprotected external connector wiring away from sensitive traces. Confirm the RS-232 signal levels and data direction in the system schematic, and verify that the 250kbps rating covers the required baud rate with suitable margin. Use the manufacturer pin-description table and pinout drawing when assigning connector and logic-net connections. This page combines the manufacturer interface description, distributor package information, replacement guidance, parameter comparisons, and practical PCB considerations in a form intended to accelerate component selection and hardware design.

RFC Hubungi kami
MAX3384EEAP - 3V RS-232 Transceiver, 250kbps | Analog Devices
MAX3384EEAP

MAX3384EEAP - 3V RS-232 Transceiver, 250kbps | Analog Devices

The Analog Devices MAX3384EEAP is a 3V-powered EIA/TIA-232 and V.28/V.24 communications transceiver with two drivers and two receivers in a 20-pin SSOP package. It supports operation from 3V to 5.5V, delivers data rates up to 250kbps, and provides enhanced electrostatic discharge protection on the transmitter outputs and receiver inputs. The device is designed for low-power RS-232 links where supply voltage, communication speed, and transient protection are the primary design requirements. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 bipolar levels and converts received RS-232 levels back into CMOS-compatible logic. The MAX3384EEAP belongs to the interface IC hierarchy alongside serial transceivers, line drivers, and level-shifting ICs. Its two-driver, two-receiver arrangement supports full-duplex point-to-point communication, including flow-control lines between two data-terminal systems. Key features include a 3V to 5.5V supply range, operation up to 250kbps, low-power operation with shutdown and receiver active-low features, and ±15kV air-gap ESD protection on all transmitter outputs and receiver inputs. Contact discharge protection is rated at ±8kV using the IEC 1000-4-2 test method. These protection levels are important when the connector is exposed to cable discharge events or an industrial noise environment. The MAX3384E uses charge-pump circuitry to generate the bipolar voltage required by the RS-232 drivers, allowing operation from a single low-voltage supply. This architecture eliminates the need for a separate negative supply rail. The resulting single-supply implementation reduces board complexity in systems that already operate from 3.3V or 5V, while the driver stage provides the voltage swing expected by RS-232 receivers. Typical applications include industrial serial consoles, point-of-sale terminals, data-acquisition equipment, instrument control links, and embedded systems that communicate with legacy RS-232 peripherals. The 250kbps maximum data rate supports modern UART traffic while remaining compatible with the slower signaling commonly used by V.28 and V.24 equipment. The package is also suitable for compact control boards where connector access is limited. When laying out the circuit, place the device close to the RS-232 connector to minimize the length of unprotected traces between the IC and connector. Follow the pin-description and decoupling guidance in the manufacturer datasheet, and maintain the recommended charge-pump capacitor connections. Do not treat the internal ESD protection as a substitute for a properly designed external surge-protection network when cables leave the enclosure. This page combines device specifications, same-footprint drop-in alternatives, pin-level guidance, and application-focused design notes. It also highlights the MAX3384EEAP's balance of 3V supply operation, 250kbps throughput, low-power features, and enhanced IEC 1000-4-2 ESD protection for engineers evaluating a modern single-supply RS-232 interface.

RFC Hubungi kami
MAX3385ECAP - 250kbps True RS-232 Transceiver | Analog Devices
MAX3385ECAP

MAX3385ECAP - 250kbps True RS-232 Transceiver | Analog Devices

The Analog Devices MAX3385ECAP is a 2/3 transceiver with integrated charge pump and true RS-232 line drivers and receivers, operating from 3.0V to 5.5V at data rates up to 250kbps. The device is packaged in a 20-pin SSOP and provides 15kV ESD protection on its serial interface. An RS-232 transceiver is an interface integrated circuit that converts between single-ended logic-level signals and the bipolar voltage levels used by RS-232 equipment. A line driver translates logic states into RS-232-compatible outputs, while a line receiver performs the reverse conversion. The MAX3385ECAP integrates one driver and two receivers, commonly described as a 2/3 transceiver, for asymmetric point-to-point communication links. The MAX3385ECAP supports supply voltages from 3.0V to 5.5V, allowing operation from common 3.3V and 5V systems. Its maximum guaranteed data rate is 250kbps, making it suitable for point-to-point industrial control, instrumentation, data acquisition, and embedded equipment. The 15kV ESD rating strengthens its suitability for connectors and cables exposed to electrostatic discharge. Its dual charge-pump architecture generates the positive and negative voltages required for true RS-232 output levels without a separate negative supply rail. The manufacturer datasheet states that four 0.1uF capacitors are sufficient for operation from a 3.3V supply. A proprietary low-dropout transmitter output stage helps maintain compliant output levels across the supported supply range while controlling power consumption. Typical uses include serial configuration ports, test and measurement equipment, industrial controllers, barcode scanners, printers, and external data-acquisition modules. The 20-pin SSOP package supports compact surface-mount layouts, while the combination of 3.0V minimum supply, 250kbps throughput, and 15kV ESD protection makes the device appropriate for short-distance point-to-point links where logic-level UART signaling must cross an RS-232 cable. Pay attention to charge-pump capacitor placement and signal routing during PCB layout. Keep the charge-pump capacitors close to their associated pins, provide an uninterrupted ground reference beneath the interface, and route driver outputs and receiver inputs away from noisy switching nodes. These measures preserve signal integrity and reduce the chance that charge-pump switching activity will disturb adjacent circuitry. This product page combines the manufacturer interface specifications, package information, pricing availability, and practical RS-232 design guidance. It also distinguishes confirmed drop-in alternatives from functionally similar devices that require pinout, package, and operating-limit verification before substitution.

RFC Hubungi kami
MAX3385ECAP-T - 250kbps RS-232 IC | Analog Devices
MAX3385ECAP-T

MAX3385ECAP-T - 250kbps RS-232 IC | Analog Devices

Analog Devices MAX3385ECAP-T is a low-power, true RS-232 transceiver IC rated for data rates up to 250kbps and operating from a 3.0V to 5.5V supply. The device provides two drivers and three receivers in a 20-pin SSOP package and includes protection for exposed RS-232 lines rated to 15kV ESD. Its combination of multi-driver and multi-receiver channels suits equipment that exchanges data across several serial interfaces. A true RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into digital logic levels. The MAX3385ECAP-T belongs to the RS-232 transceiver family within interface ICs, where it sits between a host controller or data-processing system and a cable-based peripheral. Unlike a single-direction line driver or receiver, the integrated transceiver supports both transmission and reception while limiting the number of external interface components. The MAX3385ECAP-T supports supply voltages from 3.0V to 5.5V, making it suitable for systems that operate from either 3.3V or 5V logic rails. Its stated maximum signaling rate is 250kbps, which provides sufficient bandwidth for common point-to-point control, instrumentation, industrial, and data-acquisition links. The integrated 15kV ESD protection is a principal feature for interfaces connected to external cables, where electrostatic discharge can enter through a connector and damage an unprotected transceiver. This device is identified as a 2/3 transceiver, meaning that two driver channels and three receiver channels are available for asymmetric RS-232 links. The manufacturer datasheet describes the MAX3385ECAP as a low-power true RS-232 transceiver for 3.0V to 5.5V operation. Its SSOP-20 package provides a compact surface-mount format, while the -T ordering suffix identifies the tape-and-reel shipping form associated with this exact manufacturer part number. Typical uses include industrial control links, test and measurement equipment, data-logging systems, point-of-sale equipment, and embedded serial interfaces. The combination of a 250kbps data rate and multiple receiver channels is particularly useful where one controller must monitor several incoming RS-232 signals while transmitting command or status data through another channel. External charge-pump capacitors and connector protection arrangements should follow the pin-description and typical-application diagrams in the manufacturer datasheet. Designers should verify that the system ground and signal-return arrangement satisfy the RS-232 interface requirements before placing the IC. The maximum cable length and achievable rate depend on the complete transceiver circuit, cable impedance, connector, noise environment, and system baud rate; the 250kbps figure is the device rating rather than a guarantee for every installed link. Decoupling and charge-pump routing should follow the recommended layout because switching-regulator and charge-pump currents can couple into sensitive signal paths. This product page consolidates the exact MAX3385ECAP-T electrical ratings, package information, interface characteristics, sourcing path, and engineering guidance into one reference. It also distinguishes confirmed pin-compatible replacements from merely similar RS-232 transceivers, helping designers avoid assuming that equivalent protocol functions guarantee PCB-level drop-in compatibility.

RFC Hubungi kami
MAX3385ECWN - 250kbps True RS-232 Transceiver | Analog Devices
MAX3385ECWN

MAX3385ECWN - 250kbps True RS-232 Transceiver | Analog Devices

Analog Devices MAX3385ECWN is a true RS-232 transceiver IC supporting a 3.0V to 5.5V supply, data rates up to 250kbps, and ESD protection rated at ±15kV. The device is offered in an 18-SOIC package and provides two drivers and three receivers, making it suitable for bidirectional and multi-channel serial-interface equipment. A true RS-232 transceiver is an interface IC that converts logic-level signals to RS-232 levels and converts incoming RS-232 signals back to logic levels. RS-232 is a point-to-point, unbalanced serial-interface standard widely used for industrial control, data acquisition, instrumentation, and legacy peripheral connections. Its transmitter and receiver circuitry provide the voltage conversion and noise tolerance required when logic levels must communicate with a longer, unbalanced cable. The MAX3385ECWN supports operation from a single 3.0V to 5.5V supply, allowing use in both 3.3V and 5V systems. Its maximum data rate of 250kbps is suitable for moderate-speed serial links, and the ±15kV ESD rating adds protection for exposed connector pins. The 2/3 driver-receiver configuration is useful when a design requires more receiver channels than transmitter channels. The MAX3385ECWN family uses integrated true RS-232 line-driver and line-receiver stages rather than a limited-voltage-only interface. This distinction is important when connecting to equipment that expects RS-232 voltage levels. Its operating-temperature range is specified as 0°C to 70°C for the commercial-grade CWN configuration, making it appropriate for equipment intended for controlled indoor or industrial environments within that range. Typical uses include industrial serial adapters, programmable-logic-controller communication, test and measurement instruments, barcode and data-acquisition equipment, and embedded control systems that retain an RS-232 port. Systems operating at 250kbps should include appropriate cable routing and grounding because unbalanced RS-232 performance can still be affected by ground offsets, electromagnetic interference, and connector cable characteristics. PCB implementation should follow the manufacturer's pin and decoupling guidance, particularly for supply connections and exposed RS-232 pins. Place the required bypass capacitor close to the device, route transceiver outputs to the connector through a short and appropriately arranged path, and confirm that system grounding satisfies the interface requirements before enabling communication. This page combines the manufacturer-oriented device identity, verified distributor descriptions, RS-232 design guidance, package details, and replacement analysis. It also identifies where additional electrical, mechanical, and lifecycle information must be confirmed in the manufacturer datasheet or through a current manufacturer quotation.

RFC Hubungi kami
MAX3385EEAP - 250kbps RS-232 Transceiver | Analog Devices
MAX3385EEAP

MAX3385EEAP - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3385EEAP is a low-power RS-232 transceiver rated for data rates up to 250kbps and operation from a 3.0V to 5.5V supply. The device is offered in a 20-pin SSOP package and provides the driver and receiver functions required to connect a modern digital circuit to an RS-232 serial port. Its integrated protection is specified for ±15kV electrostatic-discharge exposure on the serial lines. An RS-232 transceiver is an interface IC that belongs to the line-driver and line-receiver hierarchy within interface semiconductors. It converts logic-level signals into RS-232-compatible levels in the transmit direction and converts incoming RS-232 levels back into logic levels in the receive direction. The MAX3385EEAP therefore provides the physical signaling layer between equipment logic and a cable-based serial interface. Key characteristics include support for both 3.0V and 5.5V supply operation, a maximum signaling rate of 250kbps, low-power design, true RS-232 transceiver operation, and ±15kV ESD protection. The 3.0V minimum supply makes the interface suitable for systems whose digital core operates below 5V, while the 5.5V upper limit allows use with conventional 5V equipment. The 250kbps rate supports modern point-to-point serial links without requiring the lower bandwidth associated with legacy communication standards. The MAX3385EEAP combines two transmit drivers and two receive receivers in one package, matching the conventional direction and signal arrangement used by RS-232 interface designs. Its integrated ESD protection reduces the amount of external protection normally required at a connector or cable entry. Applications still require correct signal routing, suitable bypass capacitance, controlled return paths, and compliance with the applicable RS-232 electrical requirements. Typical uses include industrial control consoles, test equipment, data acquisition systems, service interfaces, and embedded products that retain an RS-232 port for configuration or diagnostics. The part is particularly useful where modern 3.3V logic must communicate with an RS-232 host while board area and external protection components must be minimized. Designers should begin with the manufacturer's pin-description table when assigning PCB tracks and must preserve the documented charge-pump and driver topology around the transceiver. Input and supply bypassing should be placed close to the relevant pins, and connector-side protection must be reviewed against the required ESD exposure and working voltage. This page consolidates the core electrical and package characteristics of the MAX3385EEAP with application guidance, comparison parameters, and practical interface-design considerations. It is intended to help engineers determine whether the device's voltage range, data rate, package, and protection level match a particular RS-232 design before committing the footprint to a PCB.

RFC Hubungi kami
MAX3386ECDW - 3/2 RS-232 Transceiver, 250kbps | Texas Instruments
MAX3386ECDW

MAX3386ECDW - 3/2 RS-232 Transceiver, 250kbps | Texas Instruments

The Texas Instruments MAX3386ECDW is a full-duplex RS-232 transceiver with three drivers and two receivers, a maximum data rate of 250kbps, and a 3V to 5.5V supply range in a 20-pin SOIC package. The device includes a split logic-side supply arrangement for mixed-signal systems. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar voltage levels used by the RS-232 standard. It belongs to the communication transceiver family, which sits above line drivers and receivers in the interface hierarchy and ultimately supports serial data links in industrial, commercial, and embedded equipment. Key electrical features include 500mV receiver hysteresis for improved noise immunity, 3V to 5.5V operation, and ±25kV ESD protection as identified for this device. The three-driver, two-receiver arrangement supports multiple outbound channels and two inbound channels within one package. Full-duplex operation allows simultaneous transmission and reception, while the split supply pins give the circuit designer independent control over the logic-side supply arrangement. The MAX3386ECDW operates from 0°C to 70°C and is specified for surface-mount assembly in a 20-SOIC package measuring 0.295 inches, or 7.50mm, wide. Its 250kbps signaling rate is suitable for configuration ports, instrumentation, point-of-sale equipment, and legacy industrial control links. The integrated protection reduces the need for separate surge-protection components on exposed serial lines. Typical applications include RS-232 ports for embedded controllers, test and measurement instruments, industrial diagnostic interfaces, and data acquisition systems. Because this part is obsolete, engineers should confirm availability, lifecycle status, and any manufacturer-approved migration path before releasing a new production design. When laying out the board, keep the logic-side connections short and route the RS-232 lines away from clocks, switching regulators, and high-current power paths. Verify the external charge-pump capacitor values against the manufacturer datasheet and treat the RS-232 pins as external-facing signal nodes during EMC and ESD reviews. This page consolidates device specifications, lifecycle information, pin-compatible alternatives, and design guidance for engineers evaluating the MAX3386ECDW against current RS-232 interface options.

RFC Hubungi kami
MAX3386ECDWG4 - RS-232 Transceiver | Texas Instruments
MAX3386ECDWG4

MAX3386ECDWG4 - RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3386ECDWG4 is a dual line RS-232 transceiver with a split supply pin for the logic side, designed for mixed-voltage serial-interface systems. It is packaged in a 20-pin SOIC (0.295 inch, 7.50 mm width) and is identified as a commercial-grade RS-232 interface IC. The device supports ESD protection on the RIN inputs and DOUT outputs, including ±15 kV human-body-model protection, and is also described as a 3 V and ±25 kV ESD RS-232 device. An RS-232 transceiver is a signal-interface semiconductor that combines line drivers and line receivers to connect a digital logic system to a serial port using RS-232 electrical levels. In the hierarchy of electronic components, it belongs to the interface-IC family, specifically the RS-232 line-driver and receiver category. The split logic-side supply feature allows the logic-side voltage to be selected for compatibility with systems using mixed supply levels, while the RS-232 side handles the higher voltage signaling required by the standard. The MAX3386ECDWG4 is designed for applications requiring bidirectional or multi-line RS-232 connectivity, protection for exposed serial lines, and operation in a compact SOIC-20 package. Its stated ESD capability is particularly useful when the connector or cable interface may be exposed to electrostatic discharge during insertion, removal, or industrial handling. The commercial temperature designation indicates its intended use in commercial equipment rather than an automotive-qualified environment. The MAX3386E family uses split supply pins to support operation in mixed-signal systems. The logic-side supply feature allows a system designer to interface the transceiver with a lower-voltage digital subsystem, while the RS-232-side supply arrangement supports the voltage requirements of the line interface. The device also includes driver and receiver channels suited to point-to-point serial links, instrumentation, control equipment, and data-acquisition equipment. Typical applications include RS-232 ports in industrial controllers, laboratory instruments, POS terminals, serial adapters, embedded control boards, and communications equipment. In an industrial controller, the transceiver can place a protected RS-232 interface between a logic-level UART and an external DB9 or terminal connector. In measurement equipment, it can provide the electrical conversion and line protection needed when connecting an instrument to a host computer. Protection requirements should still be checked against the connector and cable environment. When laying out the board, place the transceiver close to the RS-232 connector and route the protected RIN and DOUT lines directly to the relevant pins to minimize exposure to electrostatic discharge and external cable transients. Confirm logic-side and RS-232-side supply levels, supply decoupling, and the UART signal levels before finalizing the design. The SOIC-20 footprint also requires adequate spacing around the pins for reliable assembly and rework. This product page combines the manufacturer-family characteristics, package information, ESD descriptions, interface details, practical application guidance, and verified replacement information for engineers evaluating the MAX3386ECDWG4. It is intended to support board-level decision making, footprint planning, cross-reference work, and RS-232 interface design rather than serving as a substitute for the complete manufacturer datasheet.

RFC Hubungi kami
MAX3386ECPW - 3 to 5.5V RS-232 Transceiver | Texas Instruments
MAX3386ECPW

MAX3386ECPW - 3 to 5.5V RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3386ECPW is a 3- to 5.5-V, 250-kbps RS-232 line driver/receiver with three drivers, two receivers, a logic supply pin, and plus-or-minus 15-kV IEC-ESD protection. The device is packaged in a 20-pin TSSOP package. It is designed for bidirectional serial-interface systems that require RS-232 line drivers and receivers in one compact surface-mount package. An RS-232 transceiver is an interface IC that combines differential line-driver and receiver functions for communicating between equipment over the RS-232 standard. The MAX3386ECPW converts logic-level signals to RS-232 levels and converts incoming RS-232 signals back to logic levels. Its 3- to 5.5-V operating range supports both 3.3-V and 5-V system rails, while the 250-kbps data rate is suitable for moderate-speed serial links. Key features include three RS-232 drivers, two RS-232 receivers, a separate logic supply pin, and plus-or-minus 15-kV IEC-ESD protection on the RS-232 inputs and outputs. The family is positioned for industrial-control, instrumentation, data-acquisition, and embedded equipment interfaces where a compact transceiver and electrostatic-discharge resilience are useful. The MAX3386ECPW is a member of the MAX3386E family, also identified by the manufacturer as the MAX3386E product page. The MAX3386E architecture uses charge-pump circuitry internally to generate the RS-232 transmit voltage levels. The logic-side supply and the driver-side supply arrangement allow the interface to operate with modern low-voltage digital logic while maintaining RS-232-compatible signal levels at the connector. The integrated protection helps reduce damage from electrostatic discharge events encountered during handling or field installation, although the complete system still requires appropriate board-level grounding and signal routing. Typical applications include industrial serial controllers, test and measurement equipment, barcode and data-acquisition systems, point-of-sale equipment, and embedded RS-232 links. The device is especially appropriate when the design needs three transmit channels and two receive channels rather than a one-driver, one-receiver RS-232 transceiver. When laying out a board using the MAX3386ECPW, place the device near the RS-232 connector and route driver and receiver traces away from sensitive analog or high-speed digital signals. Maintain the connector-side ground path and follow the manufacturer’s recommended charge-pump capacitor connections. Confirm the logic supply voltage, RS-232 connector pin assignment, and the required charge-pump capacitors during schematic and layout review. This page combines the manufacturer’s MAX3386E product information, distributor identification, package details, application guidance, and structured replacement information. It is intended to help engineers evaluate the MAX3386ECPW for RS-232 interface designs while checking exact pin, electrical, and compliance details against the manufacturer datasheet.

RFC Hubungi kami
MAX3386ECUP+ - 3/2 RS-232 Transceiver, 250kbps | Analog Devices
MAX3386ECUP+

MAX3386ECUP+ - 3/2 RS-232 Transceiver, 250kbps | Analog Devices

The Analog Devices MAX3386ECUP+ is a 3/2 RS-232 communications transceiver with three transmitters, two receivers, operation from a 3.0V to 5.5V supply, and data rates up to 250kbps. The device is housed in a 20-pin TSSOP package and is designed for low-power, portable equipment requiring EIA/TIA-232, V.28, or V.24-compatible serial interfaces. An RS-232 transceiver is an interface IC that bridges a low-voltage digital logic system and a single-ended, bipolar RS-232 link. It belongs to the communications-interface hierarchy, combining transmitter and receiver functions with the voltage conversion and protection required for unbalanced serial communication. The MAX3386ECUP+ also uses charge-pump circuitry to generate the positive and negative voltages required by RS-232 output levels from a single low-voltage supply. The MAX3386ECUP+ supports a 3.0V to 5.5V supply and operates at data rates up to 250kbps while maintaining RS-232-compliant output levels. Its dual charge pump requires four 0.1uF capacitors for operation from a 3.3V supply. The three-driver, two-receiver arrangement suits equipment with several outbound serial channels and fewer inbound channels, while enhanced electrostatic-discharge protection improves robustness in exposed cable-connected systems. The low-dropout transmitter output stage enables true RS-232 performance without requiring a 5V-only power rail, making the device useful in battery-powered and portable systems. The manufacturer describes the MAX3386E family as a low-power communications interface with high data-rate capability and enhanced ESD protection. Charge-pump switching and transmitter edge behavior should be considered when the serial link operates next to sensitive analog circuitry. Typical uses include RS-232 ports in personal digital assistants and cellular phones, diagnostic and programming interfaces, industrial equipment, point-of-sale terminals, and embedded serial adapters. Its 250kbps maximum rate provides useful margin above common asynchronous serial communication rates, while the compact 20-pin TSSOP package supports space-constrained portable products. Design the charge-pump capacitor network for the shortest practical connection to the supply and ground pins. Confirm the connector-side protection strategy and cable routing because the integrated ESD protection does not eliminate the need for correct board layout and system-level grounding. Verify signal levels and timing against the manufacturer datasheet before replacing a multi-transceiver interface. This product page combines manufacturer specifications, pin-compatible alternatives, application guidance, and practical interface-design notes. It helps engineers compare protocol capability, package compatibility, protection, and implementation constraints before selecting a compact RS-232 transceiver.

RFC Hubungi kami
MAX3386EEUP+ - 3V ESD-Protected RS-232 Transceiver | Analog Devices
MAX3386EEUP+

MAX3386EEUP+ - 3V ESD-Protected RS-232 Transceiver | Analog Devices

Analog Devices MAX3386EEUP+ is a 3V-powered EIA/TIA-232 and V.28/V.24 transceiver with three transmitters, two receivers, ±25 kV ESD protection, and a 20-pin TSSOP package. It combines low-power operation with high data-rate capability for portable equipment, data acquisition systems, and industrial serial interfaces. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232-compatible voltage levels and converts incoming RS-232 signals back into digital logic. Within the interface hierarchy, the MAX3386EEUP+ is a multi-driver, multi-receiver line-interface device designed for point-to-point serial links requiring electrostatic-discharge protection. Key features include three RS-232 drivers, two RS-232 receivers, a nominal 3V supply, and enhanced ESD protection of ±25 kV. The device targets EIA/TIA-232 and V.28/V.24 communications while emphasizing low power requirements and high data-rate capability. Its 20-pin TSSOP package supports compact surface-mount PCB construction without requiring external driver circuitry for each unidirectional RS-232 link. The MAX3386EEUP+ family provides a practical bridge between a modern microcontroller UART and a legacy RS-232 port. The three transmitters support multiple outputs, while two receivers can monitor two incoming signals or implement a hardware handshake arrangement. The ±25 kV ESD rating increases robustness at exposed connector interfaces, although board-level routing and grounding remain essential for dependable operation. Typical applications include personal digital assistants, cellular phones, portable instrumentation, barcode readers, industrial controls, and service or diagnostic equipment. It is particularly useful where a compact PCB requires several RS-232 signals but the system power supply operates near 3V. The interface supports point-to-point links rather than multidrop RS-232 networks. When designing the circuit, account for RS-232's unbalanced voltage signaling and use a suitable protection network at any externally accessible connector. Keep the transceiver and its charge-pump components away from sensitive analog areas, and follow the Analog Devices pin-description table when assigning connector and logic signals. Confirm the exact data rate, supply range, and operating temperature limits against the manufacturer datasheet before release. This page combines the manufacturer's interface description, package information, drop-in candidates, application guidance, and design considerations to support faster component evaluation and sourcing decisions.

RFC Hubungi kami
MAX3386EIDW - 3/2 RS-232 Transceiver | Texas Instruments
MAX3386EIDW

MAX3386EIDW - 3/2 RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3386EIDW is a 3-driver, 2-receiver RS-232 transceiver with a split supply pin for the logic side, a 20-SOIC package, and enhanced ESD protection rated at ±25 kV on the RIN inputs and DOUT outputs. It is designed for mixed-voltage systems in which the transceiver logic side requires a separate supply from the RS-232 side. An RS-232 transceiver is an interface IC that bridges a digital logic system and an RS-232 serial link. In the transmit direction, drivers convert logic-level signals into RS-232 levels; in the receive direction, receivers convert RS-232 inputs into compatible logic levels. The MAX3386E belongs to the interface IC hierarchy and supports bidirectional serial connectivity between embedded equipment and external data ports. The MAX3386EIDW provides three transmit drivers and two receive inputs, allowing one logic-side connection to serve multiple RS-232 lines. Its split VL supply arrangement supports mixed-voltage logic systems by allowing the logic-side supply to be selected independently from the transceiver’s other supply connections. Enhanced input and output ESD protection improves robustness against electrostatic discharge encountered during normal handling, cable connection, and industrial environments. The MAX3386EIDW is identified in the manufacturer documentation as the MAX3386E RS-232 transceiver with split supply pin for logic side. It is offered in a 20-SOIC package measuring 0.295 inches, or 7.50 mm, in body width. The E suffix denotes enhanced ESD protection, while the exact operating-temperature grade and ordering suffix details should be confirmed in the manufacturer datasheet before production release. Typical uses include industrial control links, point-of-sale equipment, serial adapters, instrumentation, and embedded systems that exchange data through RS-232 ports. The three-driver and two-receiver arrangement can support multiple signal directions on one board, while the split logic-side supply can simplify interfacing with modern low-voltage processors. Any replacement must preserve the exact pinout, supply arrangement, logic levels, and ESD requirements of the original PCB. For PCB design, keep RS-232 driver and receiver routes away from sensitive analog signals, use a solid ground reference, and place protection and bypass components close to their associated pins. Because this part is listed as obsolete by one distributor, new production designs should confirm lifecycle status and obtain an approved source before committing to a long-term bill of materials. This page combines lifecycle and package information, verified pricing treatment, drop-in replacement evaluation, and practical design guidance to support faster component selection and board-level risk assessment.

RFC Hubungi kami
MAX3386EIPW - 3V RS-232 Transceiver | Texas Instruments
MAX3386EIPW

MAX3386EIPW - 3V RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3386EIPW is a 3V-to-5.5V RS-232 line driver and receiver capable of 250kbps operation, packaged in a 20-pin TSSOP. It combines three drivers, two receivers, a split logic-side supply connection, and enhanced IEC 61000-4-2 ESD protection rated to ±15kV on receiver inputs and driver outputs. An RS-232 transceiver is an interface IC that converts between digital logic-level signals and the bipolar voltage levels used by RS-232 equipment. In the product hierarchy, it belongs to the transceiver class of interface ICs, where line drivers transmit logic signals onto the cable and line receivers reconstruct valid logic signals from the cable. The MAX3386EIPW therefore connects low-voltage digital systems to external RS-232 ports while providing the voltage translation and electrostatic-discharge protection required at exposed connectors. The MAX3386E family supports operation from 3V to 5.5V, allowing its logic-side supply to match 3.3V or 5V systems. The separate VL pin improves compatibility with mixed-voltage systems by supplying the receiver and driver interface at the desired logic level. Its 250kbps maximum data rate is suitable for moderate-speed serial links, while three drivers and two receivers support asymmetric full-duplex connections. The 20-pin TSSOP also supports compact surface-mount PCB layouts. This device does not include the integrated charge-pump capacitors found in some RS-232 transceivers. Its split-supply architecture requires the external supply arrangements specified by the manufacturer datasheet, and the logic-side supply level must be selected to match the connected digital circuitry. This makes the device particularly appropriate when a controlled logic-side voltage is preferred over a single fixed internal supply arrangement. Typical uses include industrial control equipment, test and measurement instruments, data-acquisition systems, POS terminals, and embedded serial-port interfaces. In an industrial sensor interface, the MAX3386EIPW can translate between a 3.3V controller and a ±12V RS-232 bus while the ±15kV IEC ESD protection helps reduce connector-borne discharge damage. The interface should still be paired with suitable board-level grounding and enclosure practices. When laying out the PCB, place the device near the protected RS-232 connector and route driver and receiver traces away from sensitive analog or high-speed digital signals. Confirm the logic-side voltage, external capacitor requirements, and input slew behavior against the manufacturer datasheet before release. Validate the assembled interface for the required cable length, ground-reference arrangement, and system ESD level. This page combines the manufacturer family specifications, package information, lifecycle indication, verified drop-in cross-reference information, and practical interface-design guidance to support component selection and PCB planning.

RFC Hubungi kami
MAX3387ECUG+ - 3V 250kbps RS-232 Transceiver | Analog Devices
MAX3387ECUG+

MAX3387ECUG+ - 3V 250kbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3387ECUG+ is a 3V-powered EIA/TIA-232 and V.28/V.24 communications transceiver with three transmitters, three receivers, data rates up to 250 kbps, enhanced ESD protection, and a 24-pin TSSOP package. It operates from a 3V to 5.5V supply and uses a dual charge pump with four 0.1uF capacitors for operation at 3.3V. An RS-232 transceiver is an interface IC that converts between logic-level signals and the voltage-defined bipolar signals used by RS-232 equipment. It belongs to the transceiver and line-driver/receiver hierarchy within interface ICs, bridging portable processors, cellular equipment, industrial controllers, and legacy serial ports while adding level conversion and electrostatic-discharge protection. The MAX3387E family provides three driver channels and three receiver channels, allowing three RS-232 links to be implemented in a compact design. Its low-dropout transmitter output stage is intended to preserve compliant RS-232 output levels with a supply as high as 5.5V. The manufacturer describes the device for low-power requirements, high data-rate capability, and enhanced ESD protection, with stated ±15kV protection for the MAX3387ECUG+. Its dual charge-pump architecture generates the positive and negative transmitter voltages required by RS-232 while operating from a single low-voltage supply. Four small 0.1uF charge-pump capacitors are sufficient for 3.3V operation according to the manufacturer documentation. The AutoShutdown Plus feature is intended to reduce power consumption when the interface is not active, making the part suitable for battery-powered and portable systems. Typical applications include RS-232 links in PDAs, cellular phones, data acquisition equipment, industrial controllers, point-of-sale terminals, and portable diagnostic instruments. The three-transmitter and three-receiver organization is useful where a board must expose multiple serial channels while conserving space and avoiding separate level-conversion ICs. Design should place the charge-pump capacitors close to their designated pins and route each RS-232 driver output with controlled return-path geometry. External protection may still be required for long cables or severe industrial environments, and system designers should confirm logic levels, shutdown behavior, receiver enable timing, and line-driver loading against their system requirements. This page organizes the principal electrical characteristics, package information, verified sourcing references, compatible family options, and practical interface-design considerations into a consolidated guide for engineers evaluating the MAX3387ECUG+.

RFC Hubungi kami
MAX3387ECUG+T - 250kbps RS-232 Interface | Analog Devices
MAX3387ECUG+T

MAX3387ECUG+T - 250kbps RS-232 Interface | Analog Devices

The Analog Devices MAX3387ECUG+T is a 3 V powered, 3-driver/3-receiver RS-232 communications interface operating at up to 250 kbps in a 24-pin TSSOP package. It supports supply voltages from 3 V to 5.5 V, provides enhanced electrostatic-discharge protection of ±15 kV, and uses a dual charge-pump architecture with four 0.1 µF capacitors. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 bipolar levels and converts received RS-232 levels back into CMOS-compatible logic. The RS-232 interface belongs to the communications-interface hierarchy, where it bridges portable equipment, industrial controllers, point-of-sale terminals, and other data links that require the electrical characteristics defined by EIA/TIA-232 and V.28/V.24. The MAX3387ECUG+T combines three transmitters and three receivers in one device, reducing board area in multi-port RS-232 equipment. Key features include a maximum data rate of 250 kbps, operation from a 3 V to 5.5 V supply, and ±15 kV ESD protection. The low-dropout transmitter output stage supports true RS-232 operation from a +5.5 V supply, while the dual charge pump generates the bipolar voltage required for compliant signal levels. A low-power design makes the interface appropriate for battery-operated products, including personal digital assistants and cellular phones. The device integrates three independent transmit channels and three independent receive channels, allowing one package to terminate a multi-drop or multi-port RS-232 connection. Its 250 kbps capability exceeds the speed needed by many legacy serial peripherals and supports communication links requiring more throughput than conventional low-speed RS-232 ports. The internal charge-pump arrangement reduces the external support circuitry to four small 0.1 µF capacitors. Typical applications include RS-232 links in personal digital assistants, mobile and cellular phones, portable test equipment, point-of-sale systems, industrial control panels, and embedded serial-port interfaces. The combination of three transmitters, three receivers, 3 V operation, and enhanced ESD protection is particularly useful where several serial endpoints share a compact circuit board. When laying out the design, place the four 0.1 µF charge-pump capacitors close to their specified pins, keep the RS-232 connector and signal traces physically separated from sensitive logic, and provide an appropriate return path for the bipolar interface. Confirm the logic levels, supply range, and shutdown behavior in the manufacturer datasheet before finalizing a new board. This page consolidates the MAX3387ECUG+T interface specifications, verified drop-in candidate, application guidance, and design notes into an engineering-focused reference that supports component selection, schematic review, and PCB planning beyond a basic distributor listing.

RFC Hubungi kami
MAX3387EEUG+ - 3V RS-232 Transceiver, 250kbps, ±15kV ESD | Maxim
MAX3387EEUG+

MAX3387EEUG+ - 3V RS-232 Transceiver, 250kbps, ±15kV ESD | Maxim

The Analog Devices (formerly Maxim Integrated) MAX3387EEUG+ is a 3V-powered, ±15kV ESD-protected RS-232 transceiver with three drivers and three receivers, housed in a 24-pin TSSOP package. It supports data rates up to 250 kbps, complies with EIA/TIA-232 and V.28/V.24 standards, and integrates a charge pump to generate the ±5.5V RS-232 levels from a single 3.0V to 5.5V supply. The 'E' suffix indicates the enhanced AutoShutdown Plus mode that reduces supply current to 1 µA typical when no valid cable is connected. An RS-232 transceiver is a line driver/receiver IC that translates between TTL/CMOS logic levels (0-3.3V) on the UART side and the bipolar ±5V to ±15V signal levels required by the legacy RS-232 standard on the cable side. RS-232 transceivers sit at the physical layer of serial communication and remain ubiquitous in point-of-sale terminals, industrial equipment, legacy PC peripherals, and embedded debug ports despite being superseded by USB and Ethernet in many consumer applications. Key features include ±15kV ESD protection on the RS-232 bus pins (IEC 61000-4-2 Air Gap), an integrated dual charge pump requiring only four small 0.1µF external capacitors, and an AutoShutdown Plus mode that automatically disables the charge pump and receivers when the cable is disconnected. The device operates from a single 3.0V to 5.5V supply and includes three active-low INVALID outputs for system monitoring. The MAX3387EEUG+ uses a proprietary low-power charge pump architecture combined with Maxim's AutoShutdown Plus logic, achieving 1 µA typical supply current in shutdown while still supporting 250 kbps data rates. The dual charge pump generates +7V and -7V from the input rail using only flying capacitors, eliminating the need for a ±12V system supply. Typical applications include PDA and cell phone data cables, palmtop computers, battery-powered equipment, embedded industrial controllers, GPS receivers, and point-of-sale (POS) terminals. Its single-supply 3V operation makes it ideal for portable, battery-powered designs where ±12V rails are unavailable. When designing with this device, place the four charge-pump capacitors (typically 0.1µF ceramic) as close as possible to the C1+, C1-, C2+, and V+ pins. Ensure the ESD-protected bus traces are kept short and routed away from sensitive analog signals. For systems that can tolerate a slightly larger TSSOP, the MAX3387ECUG+ offers a commercial 0°C to +70°C temperature range as an alternative. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami