Analog Devices

AD8002ANZ - Dual 600 MHz CFA, 50 mW | Analog Devices

MPN: AD8002ANZ ✓ Aktif
5.0 mA per amplifier Vdss 8-lead plastic DIP, 0.300 inch (7.62 mm) pitch Package
MOQ: 1 |

AD8002ANZ Ringkasan

The Analog Devices AD8002ANZ is a dual, low-power, high-speed current-feedback amplifier with a 600 MHz small-signal bandwidth at a gain of +1, 500 MHz bandwidth at a gain of +2, and a 1200 V/µs slew rate. The device is specified for ±5 V operation and is packaged in an 8-lead plastic DIP. Its maximum total power dissipation is 50 mW, with maximum supply current of 5.0 mA per amplifier.

A current-feedback amplifier, or CFA, is a closed-loop amplifier topology whose bandwidth and stability depend primarily on the feedback resistance rather than the closed-loop gain. In the broader hierarchy, the AD8002ANZ is an operational amplifier, an analog signal-conditioning IC, and a semiconductor designed for high-frequency amplification. This topology is especially useful where low distortion and high slew rate are required across signal levels that would challenge a conventional voltage-feedback amplifier.

The AD8002 family provides excellent video performance. According to the Analog Devices AD8002 data sheet, gain flatness is 0.1 dB through 60 MHz, differential gain error is 0.01%, and differential phase error is 0.02°. Its transimpedance linearization circuitry supports video-load driving while maintaining low distortion. The amplifier settles to 0.1% in 16 ns and operates from dual ±5 V supplies.

Two independent amplifiers are integrated into one package, making the device suitable for paired signal chains such as differential video, active filtering, gain stages, and instrumentation. Unlike a voltage-feedback amplifier, its bandwidth at a given gain is controlled primarily by the external feedback resistor. Designers should therefore use the feedback values and gain configurations shown in the manufacturer data sheet rather than treating bandwidth as a gain-independent value.

Typical applications include professional video equipment, video distribution, high-speed instrumentation, cable-driver interfaces, and active analog filters. The 8-lead DIP package favors through-hole prototype boards and legacy industrial equipment, while the 600 MHz bandwidth and 1200 V/µs slew rate support pulse and wideband signal conditioning.

The principal design consideration is power-supply bypassing. Place ceramic decoupling capacitors close to the supply pins and return each amplifier ground directly to the quiet ground plane. Feedback resistors should be short, physically compact, and isolated from high-current return paths to minimize parasitic inductance and preserve the advertised gain and phase response.

This page combines the manufacturer specifications with practical pinout, replacement, layout, and application guidance. It also identifies which electrical characteristics are suitable for drop-in comparison, helping engineers move from component selection to a reproducible analog layout without relying on generic high-speed-amplifier assumptions.

Pilihan pengganti yang segera untuk AD8002ANZ — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera AD8002ANZ (sama faktor bentuk dan kaki) — berbeza dalam Package.

Analog Devices
Package: 14-pin PDIP
Bandingkan Dengan AD8002ANZ →

AD8002AN

✅ Masuk Drop-In
📦 8-lead plastic DIP, 0.300 inch (7.62 mm) pitch
Same AD8002 dual current-feedback family and 8-lead DIP footprint; ordering-code and qualification details require comparison.

📋 Alternatif rujukan (tidak dalam katalog)

AD8002ANZ Penilaian maksimum & Ciri-ciri Elektrik

Amplifier Type Current Feedback Amplifier
Number of Circuits 2 circuits
Small-Signal Bandwidth at Gain +1 600 MHz (-3 dB)
Small-Signal Bandwidth at Gain +2 500 MHz (-3 dB)
Slew Rate 1200 V/µs
Settling Time to 0.1% 16 ns
Maximum Power Dissipation 50 mW
Maximum Supply Current 5.0 mA per amplifier
Nominal Supply Voltage ±5 V
Gain Flatness 0.1 dB to 60 MHz at gain +2 with RL = 150 ohm
Differential Gain Error 0.01%
Differential Phase Error 0.02 degrees
Kemasan 8-lead plastic DIP, 0.300 inch (7.62 mm) pitch
Jenis Pemasangan Through-hole
Packaging Tube

Konfigurasi Pin AD8002ANZ

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
Pin 1 OUT A — Output of amplifier A
Pin 2 -IN A — Inverting input of amplifier A
Pin 3 +IN A — Non-inverting input of amplifier A
Pin 4 V- — Negative power supply
Pin 5 +IN B — Non-inverting input of amplifier B
Pin 6 -IN B — Inverting input of amplifier B
Pin 7 OUT B — Output of amplifier B
Pin 8 V+ — Positive power supply

Aplikasi Biasa

AD8002ANZ patut untuk 6 aplikasis: Professional Video Amplification, High-Speed Instrumentation, Active Video Filters, Pulse Signal Conditioning, Cable Driver Interfaces, Industrial Test and Measurement.

📺

Professional Video Amplification

The AD8002ANZ is well suited to professional video gain and distribution stages because its 500 MHz bandwidth at gain +2, 1200 V/µs slew rate, and 0.1 dB gain flatness through 60 MHz preserve signal amplitude and phase relationships. One amplifier can condition a component or sync signal while the second handles another channel. The manufacturer-recommended feedback resistor should be used with a 150 ohm video load, and short PCB paths are essential to preserve the 0.01% differential gain error and 0.02° differential phase error.

🔧

High-Speed Instrumentation

The AD8002ANZ can condition fast sensor, transducer, or test signals when acquisition bandwidth must preserve pulse edges without excessive distortion. Its 600 MHz bandwidth at gain +1, 1200 V/µs slew rate, and 16 ns settling to 0.1% support wideband measurement paths, while the dual topology can implement matched gain stages or two channels of an instrument. Feedback components and signal routing must remain compact because parasitic inductance and capacitance can alter the current-feedback loop and compromise the expected step response.

🌐

Active Video Filters

For active filtering around the video range, the AD8002ANZ provides the bandwidth and slew rate needed to process signals without introducing excessive amplitude tilt or phase error. The transimpedance linearization circuitry is especially relevant when the filter must drive a 150 ohm video load. Each amplifier section can implement a different filtering or gain function, subject to the feedback and compensation values shown in the manufacturer data sheet. Decoupling and ground-plane continuity should be optimized before fine-tuning filter response.

⚡

Pulse Signal Conditioning

The AD8002ANZ can amplify and reshape fast pulses because its 1200 V/µs slew rate and 16 ns settling to 0.1% reduce slew-rate and settling limitations over the useful bandwidth. The dual configuration allows one channel to condition a pulse while the other provides gain, edge shaping, or a related monitor function. Designers must account for the current-feedback topology's dependence on feedback resistance and use a ground reference capable of handling the high-frequency return current without introducing common-mode conversion.

🌐

Cable Driver Interfaces

The AD8002ANZ is appropriate for line-driving interfaces that require low distortion across a broad video or instrumentation band. Its 500 MHz bandwidth at gain +2 and 1200 V/µs slew rate provide headroom for composite video, control signals, or other wideband analog waveforms, while the transimpedance linearization circuitry assists video-load drive. The output stage should be checked against the intended cable and termination impedance, and decoupling should be placed close to the package to prevent supply ripple from appearing as gain or phase error.

🏭

Industrial Test and Measurement

The AD8002ANZ suits legacy industrial test equipment that requires high-bandwidth analog amplification on a through-hole board. Two amplifier sections can serve separate measurement or stimulus channels, and the DIP format simplifies replacement in existing equipment. The 50 mW maximum power condition and 5.0 mA per-amplifier maximum supply current keep power requirements manageable, but the application still needs stable ±5 V rails, effective bypass capacitors, and a return path designed for high-frequency currents. Production suitability depends on the exact temperature and qualification limits.

Ringkasan Produk Disebarkan

AD8002AN Same-family DIP ordering option for dual video amplification Dipergunakan di: Professional Video Amplification, High-Speed Instrumentation, Active Video Filters, Pulse Signal Conditioning, Cable Driver Interfaces, Industrial Test and Measurement AD8002ARMZ Same electrical family in a compact MSOP package for surface-mount designs Dipergunakan di: Professional Video Amplification, Active Video Filters, Cable Driver Interfaces, Industrial Test and Measurement
What is the AD8002ANZ and what are its key specifications?
The AD8002ANZ is a dual 600 MHz current-feedback amplifier from Analog Devices packaged in an 8-lead plastic DIP. According to the Analog Devices AD8002 data sheet, it provides 500 MHz bandwidth at a gain of +2, a 1200 V/µs slew rate, and 16 ns settling to 0.1%. The two amplifiers are designed for ±5 V operation and use transimpedance linearization circuitry to support low-distortion video and high-speed signal-conditioning applications.
What is the bandwidth of the AD8002ANZ at different gains?
The AD8002ANZ has a -3 dB small-signal bandwidth of 600 MHz at a gain of +1 and 500 MHz at a gain of +2. These values are specified in the Analog Devices AD8002 data sheet. Because the AD8002 is a current-feedback amplifier, its practical bandwidth also depends on the external feedback resistor; designers should use the feedback values and gain configurations published by the manufacturer when assessing rise time and stability.
Where can I download the AD8002ANZ datasheet PDF?
The official AD8002ANZ data sheet is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/AD8002.pdf. It contains the electrical characteristics, pin descriptions, typical performance curves, power-supply requirements, and recommended application circuits. The AD8002ANZ is the 8-lead DIP ordering variant of the dual 600 MHz AD8002 current-feedback amplifier.
Where can I find the AD8002ANZ pinout and package information?
The AD8002ANZ uses an 8-lead plastic DIP with 0.300-inch, or 7.62 mm, lead pitch. Its two amplifier sections share the supply pins, allowing the first amplifier to use pins 1, 2, and 3, the second to use pins 7, 6, and 5, and the supply rails to use pins 8 and 4. Use the pin-description table in the Analog Devices AD8002 data sheet when assigning PCB tracks or probing the device.
What supply voltage does the AD8002ANZ require?
The AD8002ANZ is designed to operate on dual ±5 V supplies. The Analog Devices AD8002 product information identifies the device as a dual, low-power, high-speed amplifier intended for ±5 V operation, while the data sheet also identifies a maximum power-supply current of 5.0 mA per amplifier under the 50 mW power condition. Verify the complete electrical limits and decoupling requirements against the manufacturer data sheet before applying it outside the nominal conditions.
Is the AD8002ANZ suitable for video signal processing?
Yes, the AD8002ANZ is well suited to high-speed video amplification because the AD8002 data sheet specifies gain flatness of 0.1 dB through 60 MHz, differential gain error of 0.01%, and differential phase error of 0.02°. Its transimpedance linearization circuitry improves video-load drive, while the 1200 V/µs slew rate preserves large-signal edge fidelity. The actual distortion and output amplitude still depend on gain, load, feedback resistance, supply bypassing, and PCB implementation.
What is the slew rate and settling time of the AD8002ANZ?
The AD8002ANZ provides a slew rate of 1200 V/µs and settles to 0.1% in 16 ns. According to the Analog Devices AD8002 data sheet, these specifications make the dual amplifier suitable for wideband video, pulse, and active-filter signal paths. When evaluating settling performance, include the selected feedback resistor and external compensation network because parasitic capacitance and PCB routing also influence practical response.
What is the difference between a current-feedback amplifier and a voltage-feedback amplifier?
A current-feedback amplifier controls bandwidth primarily through its external feedback resistor, whereas a conventional voltage-feedback amplifier has bandwidth that generally decreases as closed-loop gain increases. The AD8002ANZ is a current-feedback amplifier with 600 MHz bandwidth at gain +1 and 500 MHz at gain +2. It therefore suits high-speed, low-distortion stages when the manufacturer-recommended feedback resistor is used and board parasitics are controlled.
When should I choose the AD8002ANZ over another dual high-speed amplifier?
Choose the AD8002ANZ when the design needs two current-feedback amplifiers, a 600 MHz unity-gain bandwidth, a 1200 V/µs slew rate, and an 8-lead DIP footprint. It is especially attractive for through-hole video, instrumentation, and filtering designs requiring low distortion. Select a different device when a surface-mount package, wider supply range, rail-to-rail input or output, or a different amplifier topology is required.
Is the AD8002ANZ suitable for industrial instrumentation?
The AD8002ANZ can support high-speed instrumentation when its ±5 V supply, bandwidth, power, and temperature limits are appropriate for the operating environment. Its 600 MHz bandwidth and 16 ns settling behavior are useful for conditioning fast sensor or pulse signals. The through-hole DIP package also simplifies insertion into some legacy industrial test systems, although production temperature ratings and lifecycle details should be confirmed for the exact deployment.
What is the best drop-in replacement for the AD8002ANZ?
The closest documented same-package alternative is the Analog Devices AD8002AN, which uses the same 8-lead DIP configuration and belongs to the same dual current-feedback amplifier family. A cross-brand replacement cannot be confirmed from the available technical records, so no unsupported competitor part should be treated as pin-compatible. Before substitution, verify the pinout, supply limits, bandwidth, feedback resistor, stability, and load-drive requirements in the manufacturer data sheet.
Can AD8002AN replace AD8002ANZ without PCB changes?
The AD8002AN is a same-family, same-package candidate for the AD8002ANZ because both are identified as 8-lead DIP versions of the AD8002 dual current-feedback amplifier. Their ordering codes differ, so procurement and qualification records must distinguish them. Before using it as a drop-in replacement, confirm electrical limits, temperature grade, lead finish, and lifecycle status for the exact ordering code.
What can replace the AD8002ANZ?
The AD8002AN is the only clearly supportable drop-in candidate identified in the available records because it retains the same Analog Devices AD8002 family and 8-lead DIP package. Other AD8002 suffixes may represent SOIC or reel/tube ordering variants and therefore are not automatically interchangeable without checking the package drawing. The AD8002ARMZ and AD8009ARZ use different packages, while the AD8000YRDZ has materially different bandwidth and slew-rate characteristics.
How should the AD8002ANZ be laid out for stable high-speed operation?
Place the power-supply bypass capacitors immediately beside the supply pins, use a continuous ground plane, and keep each amplifier's feedback resistor close to its output and inverting-input pins. Avoid routing high-current return paths beneath the analog signal traces, and minimize trace and via parasitics around the feedback loop. The 1200 V/µs slew rate can expose small layout defects quickly, making controlled return paths and short feedback connections essential.
Where can I buy the AD8002ANZ and what is its lead time?
Use the Request a Quote form on this page to inquire about AD8002ANZ availability, current lead time, minimum order quantity, and tube quantity. The manufacturer product page identifies the AD8002 family as production, but current channel inventory and delivery schedules should be confirmed when an order is placed. The form avoids presenting a potentially stale availability claim or unsupported delivery estimate.
How much does the AD8002ANZ cost and is it in stock?
Current commercial terms for the AD8002ANZ should be obtained through the Request a Quote form on this page. The form can provide the applicable unit quotation, stock status, quantity breaks, and expected lead time for the exact 8-lead DIP ordering code. Quote confirmation is particularly important for legacy-style DIP packages because available inventory may vary by manufacturer lot and delivery schedule.
Is AD8002ANZ the same as AD8002ARMZ?
No. The AD8002ANZ and AD8002ARMZ are both dual AD8002 current-feedback amplifiers, but their packages differ: AD8002ANZ is an 8-lead plastic DIP, while AD8002ARMZ is an 8-lead MSOP. They therefore cannot be treated as drop-in equivalents without redesigning the PCB land pattern. The AD8002AN, rather than AD8002ARMZ, is the relevant same-package ordering candidate.
What is the best Analog Devices equivalent for the AD8002ANZ?
The Analog Devices AD8002AN is the best-supported equivalent because it remains in the AD8002 family and uses the same 8-lead DIP package as the AD8002ANZ. Its ordering code must still be checked for grade, lifecycle, and packaging differences. The AD8002ARMZ is not equivalent from a PCB perspective because its MSOP footprint differs, and AD8002ARZ likewise requires verification of the SOIC land pattern.

Data referensi kejuruteraan untuk AD8002ANZ — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the AD8002ANZ for a high-speed dual current-feedback amplifier design that specifically uses the 8-lead DIP footprint. It is a strong choice for professional video, wideband instrumentation, active filtering, and pulse conditioning when 600 MHz unity-gain bandwidth, 1200 V/µs slew rate, and low video distortion are important. The AD8002AN is the closest same-family drop-in candidate and should be compared by ordering code, lifecycle, qualification, and procurement requirements. Do not choose AD8002ARMZ or AD8002ARZ as direct replacements because their surface-mount packages differ. Select a new amplifier only when requirements such as supply range, rail-to-rail operation, noise, output-current capability, or thermal performance fall outside the AD8002 specification. Regardless of the device, use manufacturer-recommended feedback values and preserve a compact, low-inductance layout.

Perbandingan dengan Gantian

Parametr Produk Ini AD8002AN
Package 8-lead plastic DIP, 0.300 inch (7.62 mm) pitch 8-lead plastic DIP, 0.300 inch (7.62 mm) pitch
Brand Analog Devices Analog Devices
Amplifier Type Dual current-feedback amplifier Dual current-feedback amplifier
Number of Circuits 2 circuits 2 circuits
Bandwidth at Gain +1 600 MHz (-3 dB) 600 MHz (-3 dB)
Bandwidth at Gain +2 500 MHz (-3 dB) 500 MHz (-3 dB)
Slew Rate 1200 V/µs 1200 V/µs
Settling Time to 0.1% 16 ns 16 ns
Maximum Power Dissipation 50 mW 50 mW
Nominal Supply ±5 V ±5 V
Gain Flatness 0.1 dB to 60 MHz at gain +2 with RL = 150 ohm 0.1 dB to 60 MHz at gain +2 with RL = 150 ohm
Packaging Tube Tube

Penyeberangsung Jelas

  • High-speed current-feedback performance in a dual amplifier (vsAD8002AN)
  • Video gain and phase accuracy (vsAD8002AN)
  • Through-hole serviceability for legacy systems (vsAD8002ARMZ)

Catatan Desain

Place supply bypass capacitors directly beside pins 4 and 8, and connect each capacitor's ground end to the quiet ground plane with the shortest practical return. Keep the feedback resistor, output trace, and inverting-input node compact because parasitic inductance in a current-feedback loop can produce overshoot or instability. Avoid routing high-current returns beneath the feedback network, and use a solid ground plane rather than fragmented or split planes beneath the amplifier.

Use the feedback resistance and gain configurations shown in the Analog Devices AD8002 data sheet. The current-feedback topology makes bandwidth strongly dependent on feedback resistance, and an arbitrary resistor change can shift frequency response or compromise stability. Account for the 1200 V/µs slew rate, 16 ns settling target, and 500 MHz bandwidth at gain +2 when defining trace length, connector transitions, and the frequency content that may excite parasitic resonances.

The AD8002 is specified for ±5 V operation, with maximum power-supply current of 5.0 mA per amplifier under the 50 mW maximum-power condition. Provide low-noise rails with sufficient decoupling and verify startup and shutdown behavior across the complete operating condition. Do not infer the complete allowable supply range, output-current capability, or quiescent-current distribution from the headline power figure; consult the electrical-characteristics table in the manufacturer data sheet before setting design limits.

Do not substitute the AD8002ARMZ or AD8002ARZ as direct PCB replacements for the DIP package: their surface-mount land patterns are different. Do not treat reel or tube suffixes as electrical alternatives without confirming the complete ordering code. After replacement, verify the feedback resistor, load value, supply polarity, pin mapping, and stability before applying the full signal range.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The AD8002ANZ is a lead-free ordering option, but separate RoHS, REACH, halogen-free, and conflict-minerals declarations were not identified. AEC-Q100 is not applicable because this is an industrial amplifier rather than an automotive-qualified device.

Data disahkan pada: 2026-11-18 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

AD8002ANZ datasheet AD8002ANZ datasheet pdf AD8002ANZ pinout AD8002ANZ specifications Analog Devices AD8002ANZ AD8002ANZ equivalent AD8002ANZ replacement AD8002ANZ drop-in replacement AD8002ANZ vs AD8002AN AD8002ANZ price AD8002ANZ stock AD8002ANZ application circuit

Komponen dan Tanda berkaitan

Analog Devices AD8002 AD8002ANZ AD8002AN AD8002ARMZ AD8002ARZ AD8009ARZ AD8000YRDZ Current Feedback Amplifier CFA Operational Amplifier Analog Signal-Conditioning IC Semiconductor Small-Signal Bandwidth Slew Rate Settling Time Gain Flatness Differential Gain Error Differential Phase Error Transimpedance Linearization Video Amplifier Active Filter High-Speed Instrumentation 8-Lead Plastic DIP Through-Hole Package
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ