AD8002ANZ - Dual 600 MHz CFA, 50 mW | Analog Devices
MPN: AD8002ANZ ✓ Hoạt độngAD8002ANZ Tóm tắt
A current-feedback amplifier, or CFA, is a closed-loop amplifier topology whose bandwidth and stability depend primarily on the feedback resistance rather than the closed-loop gain. In the broader hierarchy, the AD8002ANZ is an operational amplifier, an analog signal-conditioning IC, and a semiconductor designed for high-frequency amplification. This topology is especially useful where low distortion and high slew rate are required across signal levels that would challenge a conventional voltage-feedback amplifier.
The AD8002 family provides excellent video performance. According to the Analog Devices AD8002 data sheet, gain flatness is 0.1 dB through 60 MHz, differential gain error is 0.01%, and differential phase error is 0.02°. Its transimpedance linearization circuitry supports video-load driving while maintaining low distortion. The amplifier settles to 0.1% in 16 ns and operates from dual ±5 V supplies.
Two independent amplifiers are integrated into one package, making the device suitable for paired signal chains such as differential video, active filtering, gain stages, and instrumentation. Unlike a voltage-feedback amplifier, its bandwidth at a given gain is controlled primarily by the external feedback resistor. Designers should therefore use the feedback values and gain configurations shown in the manufacturer data sheet rather than treating bandwidth as a gain-independent value.
Typical applications include professional video equipment, video distribution, high-speed instrumentation, cable-driver interfaces, and active analog filters. The 8-lead DIP package favors through-hole prototype boards and legacy industrial equipment, while the 600 MHz bandwidth and 1200 V/µs slew rate support pulse and wideband signal conditioning.
The principal design consideration is power-supply bypassing. Place ceramic decoupling capacitors close to the supply pins and return each amplifier ground directly to the quiet ground plane. Feedback resistors should be short, physically compact, and isolated from high-current return paths to minimize parasitic inductance and preserve the advertised gain and phase response.
This page combines the manufacturer specifications with practical pinout, replacement, layout, and application guidance. It also identifies which electrical characteristics are suitable for drop-in comparison, helping engineers move from component selection to a reproducible analog layout without relying on generic high-speed-amplifier assumptions.
Bộ thay thế dễ dàng lắp đặt cho AD8002ANZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AD8002ANZ (cùng hình factor và footprint) — khác nhau ở Package.
AD8002AN
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD8002ANZ Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Current Feedback Amplifier |
| Number of Circuits | 2 circuits |
| Small-Signal Bandwidth at Gain +1 | 600 MHz (-3 dB) |
| Small-Signal Bandwidth at Gain +2 | 500 MHz (-3 dB) |
| Slew Rate | 1200 V/µs |
| Settling Time to 0.1% | 16 ns |
| Maximum Power Dissipation | 50 mW |
| Maximum Supply Current | 5.0 mA per amplifier |
| Nominal Supply Voltage | ±5 V |
| Gain Flatness | 0.1 dB to 60 MHz at gain +2 with RL = 150 ohm |
| Differential Gain Error | 0.01% |
| Differential Phase Error | 0.02 degrees |
| Hộp | 8-lead plastic DIP, 0.300 inch (7.62 mm) pitch |
| Kiểu lắp đặt | Through-hole |
| Packaging | Tube |
Cấu hình chân AD8002ANZ
| Chân 1 | OUT A — Output of amplifier A |
| Chân 2 | -IN A — Inverting input of amplifier A |
| Chân 3 | +IN A — Non-inverting input of amplifier A |
| Chân 4 | V- — Negative power supply |
| Chân 5 | +IN B — Non-inverting input of amplifier B |
| Chân 6 | -IN B — Inverting input of amplifier B |
| Chân 7 | OUT B — Output of amplifier B |
| Chân 8 | V+ — Positive power supply |
Ứng dụng tiêu biểu
AD8002ANZ phù hợp cho 6 Áp dụngs: Professional Video Amplification, High-Speed Instrumentation, Active Video Filters, Pulse Signal Conditioning, Cable Driver Interfaces, Industrial Test and Measurement.
Professional Video Amplification
The AD8002ANZ is well suited to professional video gain and distribution stages because its 500 MHz bandwidth at gain +2, 1200 V/µs slew rate, and 0.1 dB gain flatness through 60 MHz preserve signal amplitude and phase relationships. One amplifier can condition a component or sync signal while the second handles another channel. The manufacturer-recommended feedback resistor should be used with a 150 ohm video load, and short PCB paths are essential to preserve the 0.01% differential gain error and 0.02° differential phase error.
Được đề xuất
High-Speed Instrumentation
The AD8002ANZ can condition fast sensor, transducer, or test signals when acquisition bandwidth must preserve pulse edges without excessive distortion. Its 600 MHz bandwidth at gain +1, 1200 V/µs slew rate, and 16 ns settling to 0.1% support wideband measurement paths, while the dual topology can implement matched gain stages or two channels of an instrument. Feedback components and signal routing must remain compact because parasitic inductance and capacitance can alter the current-feedback loop and compromise the expected step response.
Được đề xuất
Active Video Filters
For active filtering around the video range, the AD8002ANZ provides the bandwidth and slew rate needed to process signals without introducing excessive amplitude tilt or phase error. The transimpedance linearization circuitry is especially relevant when the filter must drive a 150 ohm video load. Each amplifier section can implement a different filtering or gain function, subject to the feedback and compensation values shown in the manufacturer data sheet. Decoupling and ground-plane continuity should be optimized before fine-tuning filter response.
Được đề xuất
Pulse Signal Conditioning
The AD8002ANZ can amplify and reshape fast pulses because its 1200 V/µs slew rate and 16 ns settling to 0.1% reduce slew-rate and settling limitations over the useful bandwidth. The dual configuration allows one channel to condition a pulse while the other provides gain, edge shaping, or a related monitor function. Designers must account for the current-feedback topology's dependence on feedback resistance and use a ground reference capable of handling the high-frequency return current without introducing common-mode conversion.
Được đề xuất
Cable Driver Interfaces
The AD8002ANZ is appropriate for line-driving interfaces that require low distortion across a broad video or instrumentation band. Its 500 MHz bandwidth at gain +2 and 1200 V/µs slew rate provide headroom for composite video, control signals, or other wideband analog waveforms, while the transimpedance linearization circuitry assists video-load drive. The output stage should be checked against the intended cable and termination impedance, and decoupling should be placed close to the package to prevent supply ripple from appearing as gain or phase error.
Được đề xuất
Industrial Test and Measurement
The AD8002ANZ suits legacy industrial test equipment that requires high-bandwidth analog amplification on a through-hole board. Two amplifier sections can serve separate measurement or stimulus channels, and the DIP format simplifies replacement in existing equipment. The 50 mW maximum power condition and 5.0 mA per-amplifier maximum supply current keep power requirements manageable, but the application still needs stable ±5 V rails, effective bypass capacitors, and a return path designed for high-frequency currents. Production suitability depends on the exact temperature and qualification limits.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD8002ANZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD8002AN |
|---|---|---|
| Package | 8-lead plastic DIP, 0.300 inch (7.62 mm) pitch | 8-lead plastic DIP, 0.300 inch (7.62 mm) pitch |
| Brand | Analog Devices | Analog Devices |
| Amplifier Type | Dual current-feedback amplifier | Dual current-feedback amplifier |
| Number of Circuits | 2 circuits | 2 circuits |
| Bandwidth at Gain +1 | 600 MHz (-3 dB) | 600 MHz (-3 dB) |
| Bandwidth at Gain +2 | 500 MHz (-3 dB) | 500 MHz (-3 dB) |
| Slew Rate | 1200 V/µs | 1200 V/µs |
| Settling Time to 0.1% | 16 ns | 16 ns |
| Maximum Power Dissipation | 50 mW | 50 mW |
| Nominal Supply | ±5 V | ±5 V |
| Gain Flatness | 0.1 dB to 60 MHz at gain +2 with RL = 150 ohm | 0.1 dB to 60 MHz at gain +2 with RL = 150 ohm |
| Packaging | Tube | Tube |
Bảo phân biệt quan trọng
- High-speed current-feedback performance in a dual amplifier (vsAD8002AN)
- Video gain and phase accuracy (vsAD8002AN)
- Through-hole serviceability for legacy systems (vsAD8002ARMZ)
Ghi chú thiết kế
Place supply bypass capacitors directly beside pins 4 and 8, and connect each capacitor's ground end to the quiet ground plane with the shortest practical return. Keep the feedback resistor, output trace, and inverting-input node compact because parasitic inductance in a current-feedback loop can produce overshoot or instability. Avoid routing high-current returns beneath the feedback network, and use a solid ground plane rather than fragmented or split planes beneath the amplifier.
Use the feedback resistance and gain configurations shown in the Analog Devices AD8002 data sheet. The current-feedback topology makes bandwidth strongly dependent on feedback resistance, and an arbitrary resistor change can shift frequency response or compromise stability. Account for the 1200 V/µs slew rate, 16 ns settling target, and 500 MHz bandwidth at gain +2 when defining trace length, connector transitions, and the frequency content that may excite parasitic resonances.
The AD8002 is specified for ±5 V operation, with maximum power-supply current of 5.0 mA per amplifier under the 50 mW maximum-power condition. Provide low-noise rails with sufficient decoupling and verify startup and shutdown behavior across the complete operating condition. Do not infer the complete allowable supply range, output-current capability, or quiescent-current distribution from the headline power figure; consult the electrical-characteristics table in the manufacturer data sheet before setting design limits.
Do not substitute the AD8002ARMZ or AD8002ARZ as direct PCB replacements for the DIP package: their surface-mount land patterns are different. Do not treat reel or tube suffixes as electrical alternatives without confirming the complete ordering code. After replacement, verify the feedback resistor, load value, supply polarity, pin mapping, and stability before applying the full signal range.
Thông tin tuân thủ
The AD8002ANZ is a lead-free ordering option, but separate RoHS, REACH, halogen-free, and conflict-minerals declarations were not identified. AEC-Q100 is not applicable because this is an industrial amplifier rather than an automotive-qualified device.